DOCSLIB.ORG

OHIO Utiiversity LIBRARY TABLE of CONTENTS

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
OHIO Utiiversity LIBRARY TABLE of CONTENTS *DEVELOPMENT OF A NEAR-ZONE COMPUTER MODEL FOR INVESTIGATION OF FEASIBILITY OF GROUND CHECKING THE CAPTURE-EFFECT GLIDE SLOPE , A Thesis Presented to the Faculty of the Graduate College of Ohio University In Partial Fulfillment of the Requirements for the Degree Master of Science Thierry LANGLOIS dlESTAINTOT *- JUt3 e +fsiGZi 1984 OHIO UTiIVERSITY LIBRARY TABLE OF CONTENTS Page I . INTRODUCTION AND BACKGROUND ............................. 1 A . Introduction ........................................ 1 B . Basic Theory of Image-Type Glide Slope Systems ....... 4 1 . Image theory ...................................... 5 2 . Near.field. far-field discrimination .............. 8 I1 . CEGS DESCRIPTION ........................................ 12 A . History .............................................. B . Capture Effect Glide Slope Operation ................. 111 . DEVELOPMENT OF A NEAR-ZONE CEGS MODEL ( TGCGS ) ......... A . Existing Models ...................................... B . Near-Zone Effects Considered by TGCGS ................ 1 . Sloping reflecting plane .......................... 2 . Finite conductivity ............................... 3 . Spherical wave propagation effect ................. 4 . Array factor ...................................... 29 5 . Reflector factor .................................. 33 6 . Ground plane surface roughness .................... 33 C . TGCGS Model Summary .................................. 37 D . Model Application .................................... 41 1 . Basic analytical approach ......................... 41 2 . Fault conditions .................................. 48 3 . Other perturbations ............................... 50 4 . Ground check location selection ................... 56 5 . Clearance signal checking ......................... 59 IV . DATA (MEASUREDAND ~DELED)............................. 61 A . Tamiami Airport ...................................... 61 B . 360-Degree Phase Proximity Point ..................... 64 V . CONCLUSIONS ............................................ 66 VI. RECOMMENDATIONS ......................................... 68 VII. ACKNOWLEDGEMENTS ........................................ 69 VIII. REFERENCES ........................................... 70 IX . APPENDICES ........................................... 73 A . Image-type Glide Slope Systems ....................... 73 B . Parameters Modeled by TGCGS .......................... 74 C . General Data for Tamiami Airport CEGS ................ 76 D . TGCGS Listing ........................................ 77 LIST OF FIGURES figure Page 1 . Geometry Illustrating a Possible Deficiency in Ground Measurements Caused by Terrain Irregularities Beyond the Measuring Point .......................................... 2 2 . Glide Slope Signals in Space: Above and Below Path CDI ...... 6 3 . Summary of Orientation and Excitation of Image Elements for Image Theory ............................................ 7 4 . Example of Image Theory Application: Current Element Parallel to the Ground Plane ................................. 9 5 . Composite CEGS Radiation Pattern ............................. 15 6a . Carrier Sideband. Ecs. Radiation Pattern ..................... 16 6b . Separate Sideband. EsS. Radiation Pattern .................... 16 7 . Clearance Signal Radiation Patterns .......................... 18 8 . DDM Structure With and Without Clearance Signal.............. 19 9 . Reference Coordinate System for TGCGS Model .................. 22 10 . Image Theory for Reflected Field ............................. 24 11 . Magnitude of the Horizontally-Polarized Reflection Coef- f icient vs . Incidence Angle for Various Ground Plane Electrical Constants (modeled) ............................... 26 12 . Geometry Illustrating How to Reduce Spherical Wave In- cidence into Infinite Series of Plane Wave Reflections ....... 27 13 . Spherical Wave Propagation Effect on Reflection Coefficient .4 (angle of incidence .80'. 0 .1 X 10 dm. E~ .3) .."" ... 30 14 . Antenna Products Company FA8976 .............................. 31 15 . Three-Element Colinear Antenna Array ......................... 32 16 . Modeled Array Factor vs . Azimuth Angle for Normal and Faulty System ...................................................... 34 17 . Image Theory Applied to Corner Reflector ..................... 35 18. Modeled Reflector Factor Magnitude vs. Elevation Angle ....... 36 19. Modeled Magnitude of the Roughness Coefficient vs. Angle for Various Roughness Parameters (roughness parameter = h) ....... 38 20. TGCGS Block Diagram.......................................... 39 21. Modeled CDI vs. Receiving Antenna Height at the 122244 Ground Check Point for a Normal System.............................. 40 22. Theoritical Airport Geometry with Grid Used for Primary TGCGS Tests........................................................ 43 23. CDI vs. Receiving Antenna Height for Grid Line X = 30,5m..... 44 24. CDI vs. Receiving Antenna Height for Grid Line X = 61m....... 45 25. CDI vs. Receiving Antenna Height for Grid Line X = 91.5m..... 46 26. CDI vs. Receiving Antenna Height for Grid Line X = 122m (in Front of the Antenna Mast) ................................... 47 27. Effect of Faults in CEGS System on Glide Path Performances... 49 28. Modeled CDI vs. Receiving Antenna Height for Normal System and for Broad and Narrow Alarms..............,............... 51 29. Modeled CDI vs. Receiving Antenna Height with -+ 15O Dephasing of the Lower Antenna......................................... 52 30. Modeled CDI vs. Receiving Antenna Height with -+ 15O Dephasing of the Middle Antenna......,.......................... 53 31. Modeled CDI vs. Receiving Antenna Height with -+ 15' Dephasing of the Upper Antenna.....,................................... 54 32. Modeled CDI vs. Receiving Antenna Height. Effect of Atten- uation in Antenna Currents..,................................ 55 33. Modeled CDI vs. Receiving Antenna Height for Various Reflect- ing Ground Electric Constants................,............. 57 34. Modeled CDI vs. Receiving Antenna Height for Various Snow Depths.....................................,................. 58 35. Clearance Signal Relative Strength for Normal and Fault Con- ditions.................................,................... 60 36. Control Points for ILS Site at New Tamiami Airport, Florida.. 62 37. CEGS Transmitter Mast Equipped with Three FA8976 Antennas.... 63 38. Measured and Modeled 01 vs. Elevation Angle for the 360' Phase Proximity Point Located Directly in Front of the Anten- na Mast.............................,...................... 65 I. INTRODUCTION AND BACKGROUND A. Introduction. Aircraft Instrument Landing Systems are designed to provide operational capability to permit the pilot of any appropri- ately equipped aircraft to approach and land at an airport during con- ditions of marginal visibility. Safety is clearly essential for air- craft operation. The performance record is impressive; these systems have been working for four decades and no accident has been attributed to ILS failure. Thus, the impetus for the work presented here is not safety, but cost. Currently, the integrity of ILS operation is maintained by costly periodic airborne masurements in addition to some form of near-f ield monitoring. A lower cost alternative, which is the topic of this paper, substitutes near-field ground measurements for the airborne measurements. A clearly apparent deficiency in ground measurements, as opposed to airborne measurements, is that path variations caused by terrain irregularities beyond the measuring point cannot be sensed. An illus- tration is shown in figure 1. To account for the effects of terrain irregularities using ground measurements, a program is outlined here which employs a terrain-sensitive glide slope model [l] in conjunction with near-field ground measurements to verify that a glide slope system is performing within safety tolerances. Terrain irregu larities beyond the measurement point resulting in possible path variation G.S. mast ground measurement ground I antenna I Figure 1 . Geometry Illustrating a Possible Deficiency in Ground Measurements Caused by Terrain Irregularities Beyond the Measuring Point. An additional consideration of the ground-based measurements is the sensitivity of the current near-zone monitor to environmental variations. Specifically, conditions can exist, such as snow on the ground plane [2], that cause the near-field monitor to sense an out- of-tolerance situation, although the far-field glide path is within tolerance. Circumstances such as this are clearly not in the best interests of safety, as they deprive the pilot of electronic guidance, often when it is most needed. To reduce the occurrence of unnecessary system outages resulting from the over-sensitivity of the near-field monitor, the measurement procedure presented in this paper can be per- formed as the monitor approaches on out-of-tolerance condition to determine whether the monitor indication is representative of the far- field signal or is merely influenced by some extraneous factor. The objective of this work is to investigate the feasibility of ground checking a glide slope facility both as a substitute for flight checking and for routine system maintenance. The means of this inves- tigation will be the use of computer models to study near-zone glide slope signal behavior and to correlate near-field measurements to far- field glide path characteristics. Basically, these measurements will be made by raising a horizontal dipole
Load more

Recommended publications
  • 7.3 ANTENNAS and WAVE PROPAGATION 7.3.1 Objectives
    7.3 ANTENNAS AND WAVE PROPAGATION 7.3.1 Objectives and Relevance 7.3.2 Scope 7.3.3 Prerequisites 7.3.4 Syllabus i. JNTU ii. GATE iii. IES 7.3.5 Suggested Books 7.3.6 Websites 7.3.7 Experts’ Details 7.3.8 Journals 7.3.9 Findings and Developments 7.3.10 Session Plan 7.3.11 Question Bank i. JNTU ii. GATE iii. IES 7.3.1 OBJECTIVES AND RELEVANCE Through this subject, Students can understand the physical concept of Radiation and they can relate real- world situations. They can learn about various types of antennas, its working principle and design. Since Hertz and Marconi, antennas have become increasingly important to our society until now they are indispensable. They are everywhere: at our homes and workplaces, on our cars and aircrafts. While our ships, satellites and spacecrafts bristle with them, even as pedestrians we carry them. “With mankind’s activities expanding into space, the need for antennas will grow to an unprecedented degree. Antennas will provide the vital links to and from everything out there. 7.3.2 SCOPE It gives about the basic concepts of the antenna parameters and also about the various antenna theorems in detail. Antennas are the basic components of any electric systems and are connecting links between the transmeter and free space and the receiver. Antenna place a vital role in finding the characteristics of the system in which antennas are employed. It gives in detail about the various types of microwave, VHF, and UHF antennas, their characteristics and the various applications.
    [Show full text]
  • Design of Cellular and GNSS Antenna for Iot Edge Device
    Master Thesis Master's Programme in Electronics Design, 60 credits Design of Cellular and GNSS Antenna for IoT Edge Device in collaboration with HMS Industrial Networks AB Electronics Engineering,15 credits Halmstad 2019-04-10 Ioannis Broumas HALMSTAD UNIVERSITY 60 Credits Author Ioannis Broumas Supervisor Johan Malm Examiner Pererik Andreasson School of Information Technology Halmstad University PO Box 823, SE-301 18 HALMSTAD Sweden 2 Abstract Antennas are one of the most sensitive elements in any wireless communication equipment. Designing small-profile, multiband and wideband internal antennas with a simple structure has become a necessary challenge. In this thesis, two planar antennas are designed, simulated and implemented on an effort to cover the LTE-M1 and NB-IoT radio frequencies. The cellular antenna is designed to receive and transmit data over the eight-band LTE700/GSM/UMTS, and the GNSS antenna is designed to receive signal from the global positioning system and global navigation systems, GPS (USA) and GLONASS. The antennas are suitable for direct print on the system circuit board of a device. Related theory and research work are discussed and referenced, providing a strong configuration for future use. Recommendations and suggestions on future work are also discussed. The proposed antenna system is more than promising and with further adjustments and refinement can lead to a fully working solution. 3 Στον αδελφό μου Μάκη 4 Contents 1. Introduction ...............................................................................................................................................
    [Show full text]
  • Antenna Basics 9
    M09_RAO3333_1_SE_CHO9.QXD 4/9/08 2:40 PM Page 339 CHAPTER Antenna Basics 9 In the preceding chapters, we studied the principles of propagation and transmission of electromagnetic waves. The remaining important topic pertinent to electromagnetic wave phenomena is radiation of electromagnetic waves. We have, in fact, touched on the principle of radiation of electromagnetic waves in Chapter 4 when we derived the electromagnetic field due to the infinite plane sheet of sinusoidally time-varying, spa- tially uniform current density. We learned that the current sheet gives rise to uniform plane waves radiating away from the sheet to either side of it. We pointed out at that time that the infinite plane current sheet is, however, an idealized, hypothetical source. With the experience gained thus far in our study of the elements of engineering elec- tromagnetics, we are now in a position to learn the principles of radiation from physi- cal antennas, which is our goal in this chapter. We shall begin the chapter with the derivation of the electromagnetic field due to an elemental wire antenna, known as the Hertzian dipole. After studying the radia- tion characteristics of the Hertzian dipole, we shall consider the example of a half- wave dipole to illustrate the use of superposition to represent an arbitrary wire antenna as a series of Hertzian dipoles in order to determine its radiation fields. We shall also discuss the principles of arrays of physical antennas and the concept of image antennas to take into account ground effects. Finally, we shall briefly consider the receiving properties of antennas and learn of their reciprocity with the radiating properties.
    [Show full text]
  • Principles of Radiation and Antennas
    RaoCh10v3.qxd 12/18/03 5:39 PM Page 675 CHAPTER 10 Principles of Radiation and Antennas In Chapters 3, 4, 6, 7, 8, and 9, we studied the principles and applications of prop- agation and transmission of electromagnetic waves. The remaining important topic pertinent to electromagnetic wave phenomena is radiation of electromag- netic waves. We have, in fact, touched on the principle of radiation of electro- magnetic waves in Chapter 3 when we derived the electromagnetic field due to the infinite plane sheet of time-varying, spatially uniform current density. We learned that the current sheet gives rise to uniform plane waves radiating away from the sheet to either side of it. We pointed out at that time that the infinite plane current sheet is, however, an idealized, hypothetical source. With the ex- perience gained thus far in our study of the elements of engineering electro- magnetics, we are now in a position to learn the principles of radiation from physical antennas, which is our goal in this chapter. We begin the chapter with the derivation of the electromagnetic field due to an elemental wire antenna, known as the Hertzian dipole. After studying the radiation characteristics of the Hertzian dipole, we consider the example of a half-wave dipole to illustrate the use of superposition to represent an arbitrary wire antenna as a series of Hertzian dipoles to determine its radiation fields.We also discuss the principles of arrays of physical antennas and the concept of image antennas to take into account ground effects. Next we study radiation from aperture antennas.
    [Show full text]
  • Antenna & Wave Propagation
    COMPUCOM INSTITUTE OF TECHNOLOGY & MANAGEMENT, JAIPUR (DEPARTMENT OF ELECTRONICS & COMMUNICATION) Notes Antenna & Wave Propagation (Subject Code: 7EC1) Prepared By: Raj Kumar Jain Class: B. Tech. IV Year, VII Semester Antenna & Wave Propagation Antenna Array Unit –II Antenna Array The study of a single small antenna indicates that the radiation fields are uniformly distributed and antenna provides wide beam width, but low directivity and gain. For example, the maximum radiation of dipole antenna takes place in the direction normal to its axis and decreases slowly as one moves toward the axis of the antenna. The antennas of such radiation characteristic may be preferred in broadcast services where wide coverage is required but not in point to point communication. Thus to meet the demands of point to point communication, it is necessary to design the narrow beam and high directive antennas, so that the radiation can be released in the preferred direction. The simplest way to achieve this requirement is to increase the size of the antenna, because a larger-size antenna leads to more directive characteristics. But from the practical aspect the method is inconvenient as antenna becomes bulky and it is difficult to change the size later. Another way to improve the performance of the antenna without increasing the size of the antenna is to arrange the antenna in a specific configuration, so spaced and phased that their individual contributions are maximum in desired direction and negligible in other directions. This way particularly, we get greater directive gain. This new arrangement of multi-element is referred to as an array of the antenna.
    [Show full text]
  • Radiation of Turnstile Antennas Above a Conducting Ground Plane Kirk T
    Radiation of Turnstile Antennas Above a Conducting Ground Plane Kirk T. McDonald Joseph Henry Laboratories, Princeton University, Princeton, NJ 08544 (September 18, 2008) 1Problem A “turnstile” antenna [1, 2] consists of a pair of linear dipole antennas oriented at 90◦ to each other, and driven 90◦ out of phase, as shown in Fig. 1. Figure 1: A “turnstile” antenna. From [2]. The linear antennas could be either dipoles as shown in the figure, or simply monopoles. Consider the case that the length of the linear antennas is small compared to a wavelength, −iωt so that it suffices to characterize each antenna by its electric dipole p1,2e , where the ◦ magnitudes p1 and p2 are equal but their phases differ by 90 , the directions of the two ◦ moment differs by 90 , i.e., p1 · p2 =0,andω is the angular frequency. Discuss the angular distribution and the polarization of radiation by turnstile antennas in various configurations. The two antennas may or may not be at the same point in space, and they may or may not be above a conducting ground plane. 2Solution 2.1 The Basic Turnstile Antenna We first consider a basic turnstile antenna whose component antennas lie in the x-y plane at a common point. Then, we can write the total electric dipole moment of the antenna system as −iωt −iωt p = p0e = p0(xˆ + iyˆ)e , (1) 1 The electromagnetic fields in the far zone are then ei(kr−ωt) k2 × , × , B = r ˆr p0 E = B ˆr (2) whose components in spherical coordinates are Er = Br = ˆr · B =0, (3) ei(kr−ωt) E B p k2 θ φ i φ , θ = φ = 0 r cos (cos + sin ) (4) ei(kr−ωt) E −B −p k2 φ − i φ , φ = θ = 0 r (sin cos ) (5) noting that rˆ×xˆ =sinφ θˆ +cosθ cos φ φˆ,andrˆ×yˆ = − cos φ θˆ +cosθ sin φ φˆ.
    [Show full text]
  • Chapter-3 Wire Antennas
    Chapter-3 Wire Antennas 1. Introduction In Chapter-2, we have just indicated that a short dipole antenna is not a good radiator of electromagnetic power because of its low radiation resistance and low radiation efficiency. We now examine the radiation characteristics of a center-fed thin straight antenna having a length comparable to a wavelength, as shown in Fig.5. Such an antenna is a linear dipole antenna. If the current distribution along the antenna is known, we can find its radiation field by integrating over the entire length of the antenna the radiation field due to an elemental dipole. The determination of the exact current distribution on such a seemingly simple geometrical configuration (a straight wire of a finite radius) is, however, a very difficult boundary-value problem even if the wire is assumed to be perfectly conducting. The current must be zero at the ends of the wire where charges are deposited, and the tangential electric field due to all currents and charges must vanish at every point on the wire surface. An analytical formulation of the problem leads to an integral equation in which the current distribution along the antenna is the unknown function under the integral. Unfortunately, an exact solution of the integral equation does not exist. Various approximate solutions have been attempted. With the advent of high- speed digital computers, numerical solutions for current distributions and input impedances can be obtained for linear antennas of specific lengths and thicknesses. The ratio of the voltage and the current at the feed points is the input impedance.
    [Show full text]
  • PA-22 Design Application Note
    PA-22 Design Application Note CONTENTS 1. PIFA BASICS 2. GROUND PLANE SIZE 3. BANDWIDTH 4. GAIN 5. TECHNOLOGY ADVANTAGES 6. MOUNTING 7. ENVIRONMENTAL CONSIDERATIONS 8. TUNING ©Copyright 2006 All Rights Reserved. Taoglas Limited Unit 3, Enniscorthy Technology Centre, Mile House Road, Enniscorthy, Co. Wexford, Ireland. [email protected] www.taoglas.com 1. PIFA Basics The PA-22 Planar Inverted F Antenna (PIFA) consists of a rectangular planar element located above a ground plane, a short circuiting plate, and a feeding mechanism for the planar element. The PIFA is a variant of the monopole where the top section has been folded down so as to be parallel with the ground plane. This is done to reduce the height of the antenna, while maintaining a resonant trace length. This parallel section introduces capacitance to the input impedance of the antenna, which is compensated by implementing a short-circuit stub. The stub’s end is connected to the ground plane via the short circuiting plate on the edge of the antenna, whose function is to extend the bandwidth of the PIFA. The ground plane of the antenna plays a significant role in its operation. Excitation of currents in the PIFA causes excitation of currents in the ground plane. The resulting electromagnetic field is formed by the interaction of the PIFA and an ‘image’ of itself below the ground plane. Its behaviour as a perfect energy reflector is consistent only when the ground plane is infinite or very much larger in its dimensions than the monopole itself. In practice the groundplane area is of comparable dimensions to the monopole and forms the ‘image antenna’ which is one half of the dipole.
    [Show full text]
  • AN853: Single-Ended Antenna Matrix Design Guide
    AN853 SINGLE-ENDED ANTENNA MATRIX DESIGN GUIDE 1. Introduction This application note describes the design challenges, difficulties, and conclusions regarding single-ended Antenna Matrix design. It also discusses the effects of human hand proximity on these antennas. The single-ended antennas used in the Antenna Matrix are mostly specialized monopole antennas. Most of the antennas are printed, but there are also helical wire examples and chip antennas. Unfortunately, the internal structures of the chip antennas are unknown, so the tuning possibilities are limited. 2. Antenna Basics This section describes the essential antenna definitions and principles required to understand subsequent sections in this application note. Many books and papers discuss this field in detail ([1], [2], [3], [4], [5]). Proceed to the next section if already familiar with the terms and concepts below. An antenna transforms conducted RF power to radiated RF power. DC current or static charge does not radiate. Only accelerating electrical charges create radiation, so alternating currents or pulses with discontinuities (wire ends, bending, etc.) in the conductor are required. Planar Type Wire or Printed Transmission Line Trace Radiator Figure 1. Transmission Line and Antenna Rev. 0.1 7/15 Copyright © 2015 by Silicon Laboratories AN853 AN853 2.1. Near Field and Far Field The space around the antenna can be divided into near field and far field regions. Figure 2. Near Field and Far Field Regions The main property of the far field region is that the radiation pattern does not change with the distance. However, in the near field region, the radiation pattern strongly depends on the distance from the antenna.
    [Show full text]
  • 6750.16E Siting Criteria for Instrument Landing Systems
    ORDER 6750.16E SITING CRITERIA FOR INSTRUMENT LANDING SYSTEMS April 10, 2014 DEPARTMENT OF TRANSPORTATION FEDERAL AVIATION ADMINISTRATION Distribution: A-WXYZ-1; A-FFS-0 (SUPV); A-FIA-0 (SUPV) Initiated By: AJM-3221 A-FAS-1 (SUPV); A-FAT-2 (SUPV); A-FAF-0 (LTD) RECORD OF CHANGES DIRECTIVE NO 6750.16E CHANGE CHANGE SUPPLEMENT OPTIONAL TO SUPPLEMENT OPTIONAL TO BASIC BASIC FAA FORM 1320-5 (6-80) USE PREVIOUS EDITION ORDER 6750.16E National Policy Effective Date: 04/10/14 SUBJ: Siting Criteria for Instrument Landing Systems The material in this order is a result of a total review of Order 6750.16D. The purpose of the revision is to delete obsolete material that addressed antenna systems and other units that are no longer used, certain practices and requirements that are no longer required, and items of a similar nature. Distribution: A-WXYZ-1; A-FFS-0 (SUPV); A-FIA-0 (SUPV); Initiated By: AJM-3221 A-FAS-1 (SUPV); A-FAT-2 (SUPV); A-FAF-0 (LTD) 4/10/2014 6750.16E Table of Contents Paragraph Page Chapter 1. General Information 1. Purpose of This Order ............................................................................................................. 1-1 2. Audience ................................................................................................................................. 1-1 3. Where Can I Find This Order?................................................................................................ 1-1 4. Cancellation. ..........................................................................................................................
    [Show full text]
  • DESIGN of an IMAGE RADIATION MONITOR for ILS GLIDE SLOPE in the PRESENCE of SNOW a Dissertation Presented to the Faculty of The
    DESIGN OF AN IMAGE RADIATION MONITOR FOR ILS GLIDE SLOPE IN THE PRESENCE OF SNOW A Dissertation Presented to The Faculty of the Fritz J. and Dolores H. Russ College of Engineering and Technology Ohio University In Partial Fulfillment of the Requirement for the Degree Doctor of Philosophy by Frank Marcum August, 1995 ACKNOWLEDGMENTS The author wishes to thank Dr. Roger Radcliff for his support over the years and his help in organizing this material. Mr. Joe Shovlin is also recognized for his help in reviewing the technical papers associated with this material. TABLE OF CONTENTS Page LIST OF FIGURES GLOSSARY vii I. INTRODUCTION 11. PREVIOUS RESEARCH 111. DESCRIPTION OF GLIDE SLOPE AND PARAMETERS IV. CALCULATION OF FIELD FROM ANTENNA OVER GROUND A. The Optical Approximation B. Validity of the Optical Approximation V. GLIDE SLOPE PERFORMANCE VS. REFLECTION COEFFICIENT A. Null Reference B. Sideband Reference C. Capture Effect VI. EFFECT OF SNOW OVER GROUND VII. ANALYSIS OF SNOW EFFECTS A. Effects on Null Reference Glide Slope B. Effects on Sideband Reference Glide Slope C. Effects on Capture Effect Glide Slope D. Probability of Snow Type E. Effects of Rough Snow Surfaces and Terrain VIII. MONITOR DESIGN CONCEPT A. Monitor Error Budgets and Calibration B. Monitor Siting Criteria IX. CONCLUSIONS BIBLIOGRAPHY A. Ohio University Documents B. FAA Literature APPENDIX A. Tolerance Limits ABSTRACT LIST OF FIGURES Page 1. Vertical Position of Aircraft Relative to Course Deviation Indicator. 18 2. Two-Dimensional Geometry of Problem. 21 3. Geometry of Optical Problem. 4. Minimum Distances for Surface Wave and Space Wave Equality. 26 5.
    [Show full text]
  • A Uniform Geometrical Theory of Diffraction Model of Very-High-Frequency
    A Uniform Geometrical Theory of Diffraction Model of Very-High-Frequency Omni-directional Range Systems for Improved Accuracy A thesis presented to the faculty of the Russ College of Engineering and Technology of Ohio University In partial fulfillment of the requirements for the degree Master of Science Augustine D. Yellu August 2013 © 2013 Augustine D. Yellu. All Rights Reserved. 2 This thesis titled A Uniform Geometrical Theory of Diffraction Model of Very-High-Frequency Omni-directional Range Systems for Improved Accuracy by AUGUSTINE D. YELLU has been approved for the Department of Electrical Engineering and Computer Science and the Russ College of Engineering and Technology by Chris Bartone Professor of Electrical Engineering and Computer Science Dennis Irwin Dean, Russ College of Engineering and Technology 3 ABSTRACT YELLU, AUGUSTINE D.,M.S., August 2013., Electrical Engineering A Uniform Geometrical Theory of Diffraction Model of Very-High-Frequency Omni-directional Range Systems for Improved Accuracy Director ofThesis: Chris Bartone In this thesis a computer model for predicting the radiated fields and system errors of the Conventional Very-High-Frequency (VHF) Omni-directional Range (CVOR) and the Doppler VHF Omni-directional Range (DVOR) systems was developed and validated. This software model is based on the Uniform Geometrical Theory of Diffraction (UTD) and can predict the aforementioned fields and errors for different CVOR/DVOR transmitting station configurations. By integrating the model into an existing computer model namely the Ohio University Navaids Performance Prediction Model (OUNPM), a software which predicts the performance of Instrument Landing Systems (ILS) and CVOR/DVOR systems in multipath environments, an improvement in the accuracy of the CVOR/DVOR model of the OUNPPM is achieved.
    [Show full text]