DOCSLIB.ORG

Glossary of Terms by TDK-Lambda

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Glossary of Terms by TDK-Lambda Glossary of Power Supply Terms Rev 3.0 – May 2014 Glossary of Power Supply Terms Index A....................................................................................................................................................................... 1 B....................................................................................................................................................................... 2 C....................................................................................................................................................................... 4 D....................................................................................................................................................................... 8 E..................................................................................................................................................................... 10 F..................................................................................................................................................................... 12 G..................................................................................................................................................................... 14 H..................................................................................................................................................................... 15 I....................................................................................................................................................................... 17 J...................................................................................................................................................................... 19 K..................................................................................................................................................................... 20 L...................................................................................................................................................................... 21 M..................................................................................................................................................................... 23 N..................................................................................................................................................................... 25 O..................................................................................................................................................................... 26 P..................................................................................................................................................................... 28 Q..................................................................................................................................................................... 31 R..................................................................................................................................................................... 32 S..................................................................................................................................................................... 34 T..................................................................................................................................................................... 38 U..................................................................................................................................................................... 40 V..................................................................................................................................................................... 41 W.................................................................................................................................................................... 42 X..................................................................................................................................................................... 43 Y..................................................................................................................................................................... 44 Z..................................................................................................................................................................... 45 Useful Conversion factors...............................................................................................................................46 Prefixes........................................................................................................................................................................... 46 Lengths........................................................................................................................................................................... 46 Temperature....................................................................................................................................................................46 Weights........................................................................................................................................................................... 47 Airflow............................................................................................................................................................................. 47 Energy............................................................................................................................................................................. 48 Cable Size....................................................................................................................................................................... 49 Useful Calculations......................................................................................................................................... 51 Resistance and Ohm's Law.............................................................................................................................................51 Reactance....................................................................................................................................................................... 51 Voltage Divider Rule:......................................................................................................................................................51 Electrical Energy and Power...........................................................................................................................................51 Capacitors....................................................................................................................................................................... 52 RC Circuits...................................................................................................................................................................... 52 Inductors......................................................................................................................................................................... 52 RL Circuits....................................................................................................................................................................... 53 RLC Circuits (Series Resonant)......................................................................................................................................53 RLC Circuits (Parallel Resonant)....................................................................................................................................54 Installation for optimum EMC performance.....................................................................................................55 Mounting......................................................................................................................................................................... 55 Cables............................................................................................................................................................................. 55 Connecting between boxes.............................................................................................................................................55 Earth star point................................................................................................................................................................55 External Fusing............................................................................................................................................... 56 Safety Approvals............................................................................................................................................. 57 TDK-Lambda Company Contacts...................................................................................................................58 Page ii Doc No 69639 Issue 2.2 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z Glossary of Power Supply Terms A A - Abbreviation for ampere. ac - Abbreviation for Alternating Current (written in lower case 'ac'). ac Brownout – See Brownout. ac-dc converter – A device that changes ac input voltage/current to a different dc output voltage/current. See Power Supply. ac Line – A conductor that routes ac voltage from one point
Load more

Recommended publications
  • EXPERIMENT 4: RC, RL and RD Circuits
    Laboratory 4: The RC Circuit EXPERIMENT 4: RC, RL and RD CIRCUITs Equipment List An assortment of resistor, one each of (330, 1k,1.5k, 10k,100k,1000k) Function Generator Oscilloscope 0.F Ceramic Capacitor 100H Inductor LED and 1N4001 Diode. Introduction We have studied D.C. circuits with resistors and batteries and discovered that Ohm’s Law governs the relationship between current through and voltage across a resistance. It is a linear response; i.e., 푉 = 퐼푅 (1) Such circuit elements are called passive elements. With A.C. circuits we find other passive elements called capacitors and inductors. These, too, obey Ohm’s Law and circuit loop problems can be solved using Kirchoff’ 3 Laws in much the same way as with DC. circuits. However, there is one major difference - in an AC. circuit, voltage across and current through a circuit element or branch are not necessarily in phase with one another. We saw an example of this at the end of Experiment 3. In an AC. series circuit the source voltage and current are time dependent such that 푖(푡) = 푖푠sin⁡(휔푡) (2) 푣(푡) = 푣푠sin⁡(휔푡 + 휙) where, in this case, voltage leads current by the phase angle , and Vs and Is are the peak source voltage and peak current, respectively. As you know or will learn from the text, the phase relationships between circuit element voltages and series current are these: resistor - voltage and current are in phase implying that 휙 = 0 휋 capacitor - voltage lags current by 90o implying that 휙 = − 2 inductor - voltage leads current by 90o implying that 휙 = 휋/2 Laboratory 4: The RC Circuit In this experiment we will study a circuit with a resistor and a capacitor in m.
    [Show full text]
  • Chapter 7: AC Transistor Amplifiers
    Chapter 7: Transistors, part 2 Chapter 7: AC Transistor Amplifiers The transistor amplifiers that we studied in the last chapter have some serious problems for use in AC signals. Their most serious shortcoming is that there is a “dead region” where small signals do not turn on the transistor. So, if your signal is smaller than 0.6 V, or if it is negative, the transistor does not conduct and the amplifier does not work. Design goals for an AC amplifier Before moving on to making a better AC amplifier, let’s define some useful terms. We define the output range to be the range of possible output voltages. We refer to the maximum and minimum output voltages as the rail voltages and the output swing is the difference between the rail voltages. The input range is the range of input voltages that produce outputs which are not at either rail voltage. Our goal in designing an AC amplifier is to get an input range and output range which is symmetric around zero and ensure that there is not a dead region. To do this we need make sure that the transistor is in conduction for all of our input range. How does this work? We do it by adding an offset voltage to the input to make sure the voltage presented to the transistor’s base with no input signal, the resting or quiescent voltage , is well above ground. In lab 6, the function generator provided the offset, in this chapter we will show how to design an amplifier which provides its own offset.
    [Show full text]
  • Unit-1 Mphycc-7 Ujt
    UNIT-1 MPHYCC-7 UJT The Unijunction Transistor or UJT for short, is another solid state three terminal device that can be used in gate pulse, timing circuits and trigger generator applications to switch and control either thyristors and triac’s for AC power control type applications. Like diodes, unijunction transistors are constructed from separate P-type and N-type semiconductor materials forming a single (hence its name Uni-Junction) PN-junction within the main conducting N-type channel of the device. Although the Unijunction Transistor has the name of a transistor, its switching characteristics are very different from those of a conventional bipolar or field effect transistor as it can not be used to amplify a signal but instead is used as a ON-OFF switching transistor. UJT’s have unidirectional conductivity and negative impedance characteristics acting more like a variable voltage divider during breakdown. Like N-channel FET’s, the UJT consists of a single solid piece of N-type semiconductor material forming the main current carrying channel with its two outer connections marked as Base 2 ( B2 ) and Base 1 ( B1 ). The third connection, confusingly marked as the Emitter ( E ) is located along the channel. The emitter terminal is represented by an arrow pointing from the P-type emitter to the N-type base. The Emitter rectifying p-n junction of the unijunction transistor is formed by fusing the P-type material into the N-type silicon channel. However, P-channel UJT’s with an N- type Emitter terminal are also available but these are little used.
    [Show full text]
  • KVL Example Resistor Voltage Divider • Consider a Series of Resistors And
    KVL Example Resistor Voltage Divider • Consider a series of resistors and a voltage source • Then using KVL V −V1 −V2 = 0 • Since by Ohm’s law V1 = I1R1 V2 = I1R2 • Then V − I1R1 − I1R2 = V − I1()R1 + R2 = 0 • Thus V 5 I1 = = = 1 mA R1 + R2 2000 + 3000 • i.e. get the resistors in series formula Rtotal = R1 + R2 = 5 KΩ KVL Example Resistor Voltage Divider Continued • What is the voltage across each resistor • Now we can relate V1 and V2 to the applied V • With the substitution V I 1 = R1 + R 2 • Thus V1 VR1 5(2000) V1 = I1R1 = = = 2 V R1 + R2 2000 + 3000 • Similarly for the V2 VR2 5(3000) V1 = I1R2 = = = 3V R1 + R2 2000 + 3000 General Resistor Voltage Divider • Consider a long series of resistors and a voltage source • Then using KVL or series resistance get N V V = I1∑ R j KorKI1 = N j=1 ∑ R j j=1 • The general voltage Vk across resistor Rk is VRk Vk = I1Rk = N ∑ R j j=1 • Note important assumption: current is the same in all Rj Usefulness of Resistor Voltage Divider • A voltage divider can generate several voltages from a fixed source • Common circuits (eg IC’s) have one supply voltage • Use voltage dividers to create other values at low cost/complexity • Eg. Need different supply voltages for many transistors • Eg. Common computer outputs 5V (called TTL) • But modern chips (CMOS) are lower voltage (eg. 2.5 or 1.8V) • Quick interface – use a voltage divider on computer output • Gives desired input to the chip Variable Voltage and Resistor Voltage Divider • If have one fixed and one variable resistor (rheostat) • Changing variable resistor controls out Voltage across rheostat • Simple power supplies use this • Warning: ideally no additional loads can be applied.
    [Show full text]
  • Ohm's Law and Kirchhoff's Laws
    CHAPTER 2 Basic Laws Here we explore two fundamental laws that govern electric circuits (Ohm's law and Kirchhoff's laws) and discuss some techniques commonly applied in circuit design and analysis. 2.1. Ohm's Law Ohm's law shows a relationship between voltage and current of a resis- tive element such as conducting wire or light bulb. 2.1.1. Ohm's Law: The voltage v across a resistor is directly propor- tional to the current i flowing through the resistor. v = iR; where R = resistance of the resistor, denoting its ability to resist the flow of electric current. The resistance is measured in ohms (Ω). • To apply Ohm's law, the direction of current i and the polarity of voltage v must conform with the passive sign convention. This im- plies that current flows from a higher potential to a lower potential 15 16 2. BASIC LAWS in order for v = iR. If current flows from a lower potential to a higher potential, v = −iR. l i + v R – Material with Cross-sectional resistivity r area A 2.1.2. The resistance R of a cylindrical conductor of cross-sectional area A, length L, and conductivity σ is given by L R = : σA Alternatively, L R = ρ A where ρ is known as the resistivity of the material in ohm-meters. Good conductors, such as copper and aluminum, have low resistivities, while insulators, such as mica and paper, have high resistivities. 2.1.3. Remarks: (a) R = v=i (b) Conductance : 1 i G = = R v 1 2 The unit of G is the mho (f) or siemens (S) 1Yes, this is NOT a typo! It was derived from spelling ohm backwards.
    [Show full text]
  • Thyristors.Pdf
    THYRISTORS Electronic Devices, 9th edition © 2012 Pearson Education. Upper Saddle River, NJ, 07458. Thomas L. Floyd All rights reserved. Thyristors Thyristors are a class of semiconductor devices characterized by 4-layers of alternating p and n material. Four-layer devices act as either open or closed switches; for this reason, they are most frequently used in control applications. Some thyristors and their symbols are (a) 4-layer diode (b) SCR (c) Diac (d) Triac (e) SCS Electronic Devices, 9th edition © 2012 Pearson Education. Upper Saddle River, NJ, 07458. Thomas L. Floyd All rights reserved. The Four-Layer Diode The 4-layer diode (or Shockley diode) is a type of thyristor that acts something like an ordinary diode but conducts in the forward direction only after a certain anode to cathode voltage called the forward-breakover voltage is reached. The basic construction of a 4-layer diode and its schematic symbol are shown The 4-layer diode has two leads, labeled the anode (A) and the Anode (A) A cathode (K). p 1 n The symbol reminds you that it acts 2 p like a diode. It does not conduct 3 when it is reverse-biased. n Cathode (K) K Electronic Devices, 9th edition © 2012 Pearson Education. Upper Saddle River, NJ, 07458. Thomas L. Floyd All rights reserved. The Four-Layer Diode The concept of 4-layer devices is usually shown as an equivalent circuit of a pnp and an npn transistor. Ideally, these devices would not conduct, but when forward biased, if there is sufficient leakage current in the upper pnp device, it can act as base current to the lower npn device causing it to conduct and bringing both transistors into saturation.
    [Show full text]
  • Phasor Analysis of Circuits
    Phasor Analysis of Circuits Concepts Frequency-domain analysis of a circuit is useful in understanding how a single-frequency wave undergoes an amplitude change and phase shift upon passage through the circuit. The concept of impedance or reactance is central to frequency-domain analysis. For a resistor, the impedance is Z ω = R , a real quantity independent of frequency. For capacitors and R ( ) inductors, the impedances are Z ω = − i ωC and Z ω = iω L. In the complex plane C ( ) L ( ) these impedances are represented as the phasors shown below. Im ivL R Re -i/vC These phasors are useful because the voltage across each circuit element is related to the current through the equation V = I Z . For a series circuit where the same current flows through each element, the voltages across each element are proportional to the impedance across that element. Phasor Analysis of the RC Circuit R V V in Z in Vout R C V ZC out The behavior of this RC circuit can be analyzed by treating it as the voltage divider shown at right. The output voltage is then V Z −i ωC out = C = . V Z Z i C R in C + R − ω + The amplitude is then V −i 1 1 out = = = , V −i +ω RC 1+ iω ω 2 in c 1+ ω ω ( c ) 1 where we have defined the corner, or 3dB, frequency as 1 ω = . c RC The phasor picture is useful to determine the phase shift and also to verify low and high frequency behavior. The input voltage is across both the resistor and the capacitor, so it is equal to the vector sum of the resistor and capacitor voltages, while the output voltage is only the voltage across capacitor.
    [Show full text]
  • AIX Globalization
    AIX Version 7.1 AIX globalization IBM Note Before using this information and the product it supports, read the information in “Notices” on page 233 . This edition applies to AIX Version 7.1 and to all subsequent releases and modifications until otherwise indicated in new editions. © Copyright International Business Machines Corporation 2010, 2018. US Government Users Restricted Rights – Use, duplication or disclosure restricted by GSA ADP Schedule Contract with IBM Corp. Contents About this document............................................................................................vii Highlighting.................................................................................................................................................vii Case-sensitivity in AIX................................................................................................................................vii ISO 9000.....................................................................................................................................................vii AIX globalization...................................................................................................1 What's new...................................................................................................................................................1 Separation of messages from programs..................................................................................................... 1 Conversion between code sets.............................................................................................................
    [Show full text]
  • NAME Experiment 7 Frequency Response ______PARTNER
    ECE 241L Fundamentals of Electrical Engineering _____________________ NAME Experiment 7 Frequency Response _____________________ PARTNER A. Objectives: I. Measure frequency response of RC low-pass and CR high-pass filters II. Measure frequency response of an RLC frequency selective filter III. Measure uncalibrated inductance and capacitance B. Equipment: Breadboard, resistor(s), potentiometer, wire (student lab kit), wire stripper Digital Volt-Ohm Meter (DVM): Fluke 189 (or equivalent) Oscilloscope: Tektronix TDS3043 Digital Storage Scope Function Generator: Tektronix AFG310/320 Arbitrary Function Generator Inductor: 100 mH nominal Capacitors: 0.001 and 0.1 μF nominal C. Introductory Notes: Filters: Electric circuits can be used as filters to pass certain frequencies and stop others. For example the tone control on a radio is used to vary the amount of low frequencies (bass) and high frequencies (treble) in playing music. Frequency selectable filters are used to tune in a desired station and reject other stations. This experiment will demonstrate three standard types of filters: low-pass, high-pass, and band select. Simple filters can be designed using R, C, and L in voltage divider circuits. 1. LOW-PASS FILTER A low-pass filter can be constructed as a voltage divider with a resistance R and a capacitance C in series, with the output voltage across the capacitor. Figure E4-1 Voltage divider circuit to form an RC filter In this circuit, the low-pass filter frequency response |H(f)| is given by the (dimensionless) ratio of the voltage across the capacitor divided by the input voltage. |H| = [Vc]/[Vo] From the voltage divider formula and Kirchhoff's Voltage Law for a-c circuits [Vc] = [Vo] Xc/(R2 + Xc2)0.5 From the reactance of a capacitor Xc = 1/2π f C |H| = 1 / [1 + (f / Fc)2]0.5 FREQUENCY RESPONSE OF LOW-PASS FILTER Fc = 1/2πRC FILTER CUTOFF FREQUENCY (Hz) The graph of |H| as a function of frequency is sketched in Figure E4-2 Fc (cutoff frequency) f (frequency) (Hz) Figure E4-2 Frequency response of an RC low-pass filter.
    [Show full text]
  • From Laptop to Lambda: Outsourcing Everyday Jobs to Thousands of Transient Functional Containers
    From Laptop to Lambda: Outsourcing Everyday Jobs to Thousands of Transient Functional Containers Sadjad Fouladi Francisco Romero Dan Iter Qian Li Shuvo Chatterjee+ Christos Kozyrakis Matei Zaharia Keith Winstein Stanford University, +Unaffiliated Abstract build system ExCamera Google Test Scanner (make, ninja) (video encoder) (unit tests) (video analysis) We present gg, a framework and a set of command-line front-ends gg tools that helps people execute everyday applications—e.g., model substitution substitution scriptingscripting SDK SDK C++C++ SDK SDK Python SDKSDK software compilation, unit tests, video encoding, or object recognition—using thousands of parallel threads on a cloud- functions service to achieve near-interactive completion times. IR In the future, instead of running these tasks on a laptop, or gg back-ends keeping a warm cluster running in the cloud, users might gg push a button that spawns 10,000 parallel cloud functions to Lambda/S3 Lambda/RediscomputeOpenWhisk and storageGoogle Cloudengines Functions EC2 Local execute a large job in a few seconds from start. gg is designed to make this practical and easy. Lambda/S3 Lambda/Redis OpenWhisk Google Cloud Functions EC2 Local With gg, applications express a job as a composition of lightweight OS containers that are individually transient (life- Figure 1: gg helps applications express their jobs as a composition times of 1–60 seconds) and functional (each container is her- of interdependent Linux containers, and provides back-end engines metically sealed and deterministic). gg takes care of instantiat- to execute the job on different cloud-computing platforms. ing these containers on cloud functions, loading dependencies, minimizing data movement, moving data between containers, and dealing with failure and stragglers.
    [Show full text]
  • Voltage Divider from Wikipedia, the Free Encyclopedia
    Voltage divider From Wikipedia, the free encyclopedia In electronics, a voltage divider (also known as a potential divider) is a passive linear circuit that produces an output voltage (Vout) that is a fraction of its input voltage (Vin). Voltage division is the result of distributing the input voltage among the components of the divider. A simple example of a voltage divider is two resistors connected in series, with the input voltage applied across the resistor pair and the output voltage emerging from the connection between them. Resistor voltage dividers are commonly used to create reference voltages, or to reduce the magnitude of a voltage so it can be measured, and may also be used as signal attenuators at low frequencies. For direct current and relatively low frequencies, a voltage divider may be sufficiently accurate if made only of resistors; where frequency response over a wide range is required (such as in an oscilloscope probe), a voltage divider may have capacitive elements added to compensate load capacitance. In electric power transmission, a capacitive voltage divider is used for measurement of high voltage. Figure 1: A simple voltage divider Contents 1 General case 2 Examples 2.1 Resistive divider 2.2 Low-pass RC filter 2.3 Inductive divider 2.4 Capacitive divider 3 Loading effect 4 Applications 4.1 Sensor measurement 4.2 High voltage measurement 4.3 Logic level shifting 5 References 6 See also 7 External links General case A voltage divider referenced to ground is created by connecting two electrical impedances in series, as shown in Figure 1.
    [Show full text]
  • Using Lame's Petrophysical Parameters for Fluid Detection and Lithology Determination in Parts of Niger Delta
    DOI: http://dx.doi.org/10.4314/gjgs.v13i1.4 GLOBAL JOURNAL OF GEOLOGICAL SCIENCES VOL. 13, 2015: 23-33 23 COPYRIGHT© BACHUDO SCIENCE CO. LTD PRINTED IN NIGERIA ISSN 1118-0579 www.globaljournalseries.com , Email: [email protected] USING LAME’S PETROPHYSICAL PARAMETERS FOR FLUID DETECTION AND LITHOLOGY DETERMINATION IN PARTS OF NIGER DELTA C. C. Ezeh (Received 3 March 2014; Revision Accepted 8 July 2014) ABSTRACT This study analyzed seismic and well log data in an attempt to interpret relationship between rock properties and acoustic impedance and to construct amplitude versus offset (AVO) models. The objective was to study sand properties and predict potential AVO classification. Logs of Briga 84 well provided compressional and shear velocities. AVO synthetic gather models were created using various gas/brine/oil substitutions. The Fluid Replacement Modeling predicted Class 3 AVO responses from gas sands. Log calibrated Lambda Mu Rho (LMR) inversion provided a quantitative extraction of rock properties to clearly determine lithology and fluids. Beyond the standard LMR cross-plotting that isolated gas sand clusters in the log, an improved separation of high porosity sands from shale was also achieved using λρ - µρ vs. AI. When applied to the calibrated AVO/LMR attributes inverted from 3D seismic, the λρ analysis permitted a better isolation of prospective hydrocarbon zones than standard AI inversion Thus, as an exploration tool for hydrocarbon accumulation, the Lambda Mu Rho (λµρ) technique is a good indicator of the presence of low impedance sands encased in shales which are good gas reservoirs. KEYWORDS: Impedance, synthetic gather, cross-plotting, porosity, inversion INTRODUCTION regional field structure comprises of large collapsed crest rollover anticline trending east – west and bounded The study area is situated in the eastern coastal to the north by the central swamp II depobelt.
    [Show full text]