Science Lab Equipment Notes

Total Page:16

File Type:pdf, Size:1020Kb

Science Lab Equipment Notes Science Lab Equipment Study Sheet Apparatus Description Use Name Glass As a container, cup Common Sizes: Stirring, Mixing, Pouring, BEAKER 100, 250, 400, & 1000 mL Heating Glass Usually marked with a To measure volume milliliter (mL) scale GRADUATED CYLINDER Glass A Common Sizes: 125, 250, May be heated a. ERLENMEYER FLASK B 500 ml b. ROUND BOTTOM FLASK Glass Many uses: Can be heated Several Sizes Mixing/Watching reactions TEST TUBE & TEST TUBE BRUSH Wood, metal, plastic To hold test tubes upright TEST TUBE RACK Metal Used to hold a test tube Clamp with a spring handle TEST TUBE HOLDER Metal Clamp with screws, nut, To hold test tubes securely on & curved clamp the ring stand TEST TUBE CLAMP Metal To pick up and hold a crucible CRUCIBLE TONGS Glass Used to collect/add specific volumes of liquids PIPETTE Used for suction to pull liquids PUMP into the apparatus Glass Used to hold liquids for titration Marked in milliliter scale a. BURET Fitted with a stopcock, pinch clamp, or glass bead b. BURET CLAMP Metal Clamp To hold burets when titrating With flexible clips 10 cm _________ To measure length Used to measure length METRIC RULER Divided into cm and mm divisions Triangular wire frame with To support the crucible clay material coverings CLAY TRIANGLE Small porcelain dish with To heat small amounts of solid cover material at high temperature CRUCIBLE AND COVER Wire screen with ceramic To spread the heat of a flame fibered center Rests on the ring for the ring WIRE GAUZE stand Metal heating device To heat chemicals in beakers or connected to gas outlet with test tubes BUNSEN BURNER rubber tubing Metal rod upright, heavy base A support with many uses RING STAND and RING Glass Used in the preparation of Marked off to liter capacity, solutions VOLUMETRIC FLASK with a glass stopper Plastic Used to hold liquids in micro Many different wells experiment CHEM PLATE SPOT PLATE Heavy porcelain To grind chemicals to a powder Dish with grinder MORTAR & PESTLE Metal/Porcelain To transfer chemicals in weighing CHEMICAL SCOOP Squeezable plastic bottle with To dispense distilled water angular tip WASH BOTTLE Porcelain dish As a container for small amounts of liquid being EVAPORATING DISH evaporated Curved glass May be used as a beaker cover or for evaporating small WATCH GLASS amounts of liquid Plastic Used in micro experiments to transfer small amounts of liquid MICROPIPETTE 3 metal bars with riders for Used to find the mass in grams 100s, 10s, and 1s of an object TRIPLE BEAM BALANCE measurement Digital scale, precise to the Used to find the mass in grams thousandths of a gram of an object ELECTRONIC BALANCE Usually metal or plastic with a Finds the force in (N) hook and a metal spring SPRING SCALE Electric device often with a Used to heat substances in heat and stirring controls glass or metal containers HOT PLATE Plastic, disposable Tray or paper used to hold find the mass of a chemical WEIGH BOAT Glass or plastic with lid Used to collect specimen or hold agar for growing specimen PETRI DISH Other items to know: first aid kit, fire extinguisher, apron, goggles, stopwatch, glass rod, forceps/tweezers, droppers, rubber tubing, metal file, funnel, and pH/Litmus paper (B.R.A. & R.B.B.) .
Recommended publications
  • Lab Equipment Erlenmeyer Flask
    Lab Equipment Erlenmeyer Flask • Erlenmeyer flasks hold solids or liquids that may release gases during a reaction or that are likely to splatter if stirred or heated. Beaker • Beakers hold solids or liquids that will not release gases when reacted or are unlikely to splatter if stirred or heated. Graduated Cylinder • A graduated cylinder is used to measure volumes of liquids. Test Tubes • Test tubes are used to hold small amounts of liquid and to conduct small chemical reactions in. Test Tube Clamp • A test tube holder is useful for holding a test tube which is too hot to handle. Test tube and beaker Brushes • Test tube brushes are used to clean test tubes and graduated cylinders. • Forcing a large brush into a small test tube will often break the tube. Test Tube Racks • Test tube racks are for holding and organizing test tubes on the laboratory counter. Plastic racks may melt in contact with very hot test tubes. Spot Plates • Spot plates are used when we want to perform many small scale reactions at one time. We will use these many times during the year. Watch Glass • A watch glass is used to hold a small amount of solid, such as the product of a reaction. Glass Stir Rod • A glass rod is used to manually stir solutions. It can also be used to transfer a single drop of a solution. Funnel • A funnel is used to aid in the transfer of liquid from one vessel to another. • A funnel is used to separate a solid from a liquid Wash Bottle • A wash bottle has a spout that delivers a wash solution to a specific area.
    [Show full text]
  • Microinjection & Transfection 2016-2017
    WORLD PRECISION INSTRUMENTS Instrumenting scientific ideas Microinjection & Transfection 2016-2017 Come see us at The Allied Genetics 2016 Conference • July 13-17 • Booths # 623 & 816/818 Everything you need for Microinjection Microinjection processes use either metal microinjection Recently, WPI introduced its customizable Microinjection needles or glass micropipettes to inject small liquid System with everything you need to get started. We can volumes. For example, genetic material may be inserted help you customize your system with many options and into a living cell, a drug introduced into an eye or brain, microinjection system accessories. The basic system or fluid injected into a muscle. Typically, microinjection includes: is performed under a microscope. A stereotaxic frame l Microinjection pump like the PV820 Pneumatic setup may be required. PicoPump l LED lighted microscope base with a PZMIII Stereo Microscope and an articulating mirror l Micromanipulator l Many accessories WPI offers a variety of pumps along with special syringes, stereotaxic frames, glass capillaries and needles. The setup you choose depends on the size of your microinjection aliquots, the volume to be injected and the size of needle or glass tip you choose. In addition, we offer an electroporator for transfection procedures. Whether you are working with Danio rerio (zebrafish), Xenopus, Drosophila or Caenorhabditis elegans, we can help you customize a microinjection system for your application. Options for Customizing Your System INJECTOR ✱ PV820 Pneumatic PicoPump with Hold Pressure • PV830 Pneumatic PicoPump with Hold Designed to simplify intracellular injection and a variety Microprocessor- The versatile Pressure and Vacuum of other micro in jec tion tasks, WPI's PicoPumps use UMP3 controlled injector uses • Nanoliter2010 carefully regulated air pres sures for se cur ing cells and injecting them with fluid.
    [Show full text]
  • General Chemistry Laboratory I Manual
    GENERAL CHEMISTRY LABORATORY I MANUAL Fall Semester Contents Laboratory Equipments .............................................................................................................................. i Experiment 1 Measurements and Density .............................................................................................. 10 Experiment 2 The Stoichiometry of a Reaction ..................................................................................... 31 Experiment 3 Titration of Acids and Bases ............................................................................................ 10 Experiment 4 Oxidation – Reduction Titration ..................................................................................... 49 Experiment 5 Quantitative Analysis Based on Gas Properties ............................................................ 57 Experiment 6 Thermochemistry: The Heat of Reaction ....................................................................... 67 Experiment 7 Group I: The Soluble Group ........................................................................................... 79 Experiment 8 Gravimetric Analysis ........................................................................................................ 84 Scores of the General Chemistry Laboratory I Experiments ............................................................... 93 LABORATORY EQUIPMENTS BEAKER (BEHER) Beakers are containers which can be used for carrying out reactions, heating solutions, and for water baths. They are for
    [Show full text]
  • Laboratory Equipment Reference Sheet
    Laboratory Equipment Stirring Rod: Reference Sheet: Iron Ring: Description: Glass rod. Uses: To stir combinations; To use in pouring liquids. Evaporating Dish: Description: Iron ring with a screw fastener; Several Sizes Uses: To fasten to the ring stand as a support for an apparatus Description: Porcelain dish. Buret Clamp/Test Tube Clamp: Uses: As a container for small amounts of liquids being evaporated. Glass Plate: Description: Metal clamp with a screw fastener, swivel and lock nut, adjusting screw, and a curved clamp. Uses: To hold an apparatus; May be fastened to a ring stand. Mortar and Pestle: Description: Thick glass. Uses: Many uses; Should not be heated Description: Heavy porcelain dish with a grinder. Watch Glass: Uses: To grind chemicals to a powder. Spatula: Description: Curved glass. Uses: May be used as a beaker cover; May be used in evaporating very small amounts of Description: Made of metal or porcelain. liquid. Uses: To transfer solid chemicals in weighing. Funnel: Triangular File: Description: Metal file with three cutting edges. Uses: To scratch glass or file. Rubber Connector: Description: Glass or plastic. Uses: To hold filter paper; May be used in pouring Description: Short length of tubing. Medicine Dropper: Uses: To connect parts of an apparatus. Pinch Clamp: Description: Glass tip with a rubber bulb. Uses: To transfer small amounts of liquid. Forceps: Description: Metal clamp with finger grips. Uses: To clamp a rubber connector. Test Tube Rack: Description: Metal Uses: To pick up or hold small objects. Beaker: Description: Rack; May be wood, metal, or plastic. Uses: To hold test tubes in an upright position.
    [Show full text]
  • 2019 Beverage Industry Supplies Catalog Table of Contents
    2019 Beverage Industry Supplies Catalog Table of Contents Barrels, Racks & Wood Products……………………………………………………………...4 Chemicals Cleaners and Sanitizers…………………………………………………………..10 Processing Chemicals……………………………………………………………..13 Clamps, Fittings & Valves……………………………………………………………………….14 Fermentation Bins…………………………………………………………………………………18 Filtration Equipment and Supplies……...…………………………………………………..19 Fining Agents………………………………………………………………………………………..22 Hoses…………………………………………………………………………………………………..23 Laboratory Assemblies & Kits…………………………………………………………………..25 Chemicals……………………………………………………………………………..28 Supplies………………………………………………………………………………..29 Testers………………………………………………………………………………… 37 Malo-Lactic Bacteria & Nutrients…………………………………………………………….43 Munton’s Malts……………………………………………………………………………………..44 Packaging Products Bottles, Bottle Wax, Capsules………………………………………………….45 Natural Corks………………………………………………………………………..46 Synthetic Corks……………………………………………………………………..47 Packaging Equipment…………………………………………………………………………….48 Pumps………………………………………………………………………………………………….50 Sulfiting Agents…………………………………………………………………………………….51 Supplies……………………………………………………………………………………………….52 Tanks…………………………………………………………………………………………………..57 Tank Accessories…………………………………………………………………………………..58 Tannins………………………………………………………………………………………………..59 Yeast, Nutrient & Enzymes……………………………………………………………………..61 Barrels, Racks & Wood Products Barrels Description Size Price LeRoi, New French Oak 59 gl Call for Pricing Charlois, New American Oak 59 gl Call for Pricing Charlois, New Hungarian Oak 59 gl Call for Pricing Used
    [Show full text]
  • Standard Methods for the Examination of Water and Wastewater
    Standard Methods for the Examination of Water and Wastewater Part 1000 INTRODUCTION 1010 INTRODUCTION 1010 A. Scope and Application of Methods The procedures described in these standards are intended for the examination of waters of a wide range of quality, including water suitable for domestic or industrial supplies, surface water, ground water, cooling or circulating water, boiler water, boiler feed water, treated and untreated municipal or industrial wastewater, and saline water. The unity of the fields of water supply, receiving water quality, and wastewater treatment and disposal is recognized by presenting methods of analysis for each constituent in a single section for all types of waters. An effort has been made to present methods that apply generally. Where alternative methods are necessary for samples of different composition, the basis for selecting the most appropriate method is presented as clearly as possible. However, samples with extreme concentrations or otherwise unusual compositions or characteristics may present difficulties that preclude the direct use of these methods. Hence, some modification of a procedure may be necessary in specific instances. Whenever a procedure is modified, the analyst should state plainly the nature of modification in the report of results. Certain procedures are intended for use with sludges and sediments. Here again, the effort has been to present methods of the widest possible application, but when chemical sludges or slurries or other samples of highly unusual composition are encountered, the methods of this manual may require modification or may be inappropriate. Most of the methods included here have been endorsed by regulatory agencies. Procedural modification without formal approval may be unacceptable to a regulatory body.
    [Show full text]
  • 20 Pts. Chemistry Lab: Writing Chemical Equations I
    Name(s): ________________________________________________ 20 Pts. Chemistry Lab: Writing Chemical Equations I. Purpose: To observe, predict, classify, and write balanced chemical equations that illustrate a chemical reaction. II. Procedure: 1. At each lab bench station follow the directions to perform the experiment. You must record all observations carefully. A significant portion of the grade is based on your ability to describe a chemical reaction in words as well as symbols. 2. Complete the rest of the table for each station's experiment. Classify as double displacement, single displacement, decomposition, synthesis, or combustion. Include phase notation in your balanced chemical equation. Clean up after each experiment. 3. Wear safety glasses! III. Analysis: Data: Station 1-a: Directions: Place 20 drops of ethyl alcohol in an evaporating dish. Cap and remove the bottle from the work area. Obtain a test tube that is dry on the outside and fill it 1/3rd full of cold water. Light a lighter and bring the flame close to the alcohol. Turn off lighter as soon as the alcohol ignites. With a test tube holder place the tube above the burning alcohol. Observe the outside of the test tube. Allow all of the alcohol to burn. Observation Classification Balanced chemical equation with phase not. Station 1-b: Directions: Place a scoopula of sodium hydrogen carbonate in a 150-ml beaker. Add 20-ml of vinegar (dilute acetic acid). Note the temperature of the beaker. "Pour" the gas (Not the liquid!) evolved from the reaction mixture onto the evaporating dish with the burning alcohol. Observation Classification Balanced chemical equation with phase not.
    [Show full text]
  • Product Overview
    Product Overview Electrophysiology 2020 • Patch Clamp Amplifier • Electrophysiological Accessories • Two Electrode Voltage Clamp • Electrical Shielding • Automated Patch Clamp Systems • Pipette & Electrode Manufacturing • Data Acquisition Boards • Software www.heka.com For over 45 years HEKA has designed and manufactured sophisticated instrumentation and software for biomedical and industrial research applications. Through the years, HEKA has achieved an unparalleled reputation for precision and quality. Medical, pharmaceutical and industrial research facilities world-wide rely on HEKA ingenuity for their discoveries. While there have been many changes in research, instrumentation, and software, our commitment to bring innovative technology to our customers remains constant. HEKA is a select group of engineers, biomedical researchers, and computer scientists who pride themselves on the quality of HEKA products. HEKA offers complete pre- and post-sales technical support, and takes care of each customer personally. In every way, HEKA provides solutions. HEKA Elektronik GmbH is proud to be part of the Smart Ephys umbrella. Together with our other Harvard Bioscience, Inc. brands Multi Channel Systems GmbH and Warner Instruments we offer complete solutions for electrophysiology. You will find the high-quality products and service that you know and trust from each of the individual companies, but you can get information on all products, complete set-ups (e.g. patch clamp rigs), and product consultation from one source. Please check out the Smart Ephys website and contact your local sales representative with any questions. Buy Online The Smart Ephys one-stop-shop concept applies to online orders as well. Quickly order consumables and accessories via our webshop. Expedite equipment acquisition by generating your own quote for your purchasing department.
    [Show full text]
  • Laboratory Safety Regulations Humboldt State University • Department of Chemistry Lower Level
    Version 3.0 September 28,, 2015 Laboratory Safety Regulations Humboldt State University • Department of Chemistry Lower Level FAILURE TO OBSERVE SAFETY PRECAUTIONS MAY RESULT IN IMMEDIATE DISMISSAL FROM THE LABORATORY AND ASSOCIATED LECTURE! ​ ​ A. General 1. First­Aid kits are available in the following locations: Main stockroom—SA 569; Organic Stockroom—SA 566; Analytical/Inorganic/Physical Lab—SA 369. Band­aids for minor cuts are available in the main stockroom. 2. Notify your instructor as soon as possible after all accidents and/or injuries regardless of their severity. If you need medical treatment, you will be promptly taken to the Student Health Center. In case of accident after 5:00 pm or on weekends, call the campus police at 911. ​ ​ 3. Perform no unauthorized experiments. 4. Horseplay, pranks, and other acts of mischief are strictly prohibited and will result in immediate dismissal from the laboratory. 5. Work with chemicals only after you have learned about their potential hazards. Then, proceed with caution. 6. There are always risks when working with chemicals so work cautiously and defensively. Safety Data Sheets (SDS) are available in the Main Stockroom and are also available on the Web. 7. You are required to determine the hazards of any chemical before you use the chemical. For example, ask yourself the ​ following: ​ ● What are the greatest risks from using this chemical? How can I minimize these risks? ● In what form is this chemical most hazardous? Least hazardous? ● How can I arrange my work so that the chemical is used in the least hazardous manner? ● If I have to transport this chemical, what is the safest way to do so? ● How would I respond if the chemical were spilled? 8.
    [Show full text]
  • Chemistry M11 Laboratory Manual
    Chemistry M11 Laboratory Manual Laboratory Experiments for General, Organic, and Biochemistry Compiled by the Department of Chemistry at Moorpark College Version 2.0 Fall 2020 – Present NH2 O O CN NH2 N N Co The Vitamin B molecule shown is useful in the treatment of N N 12 H2N pernicious anemia and other diseases. Enzymes derived from O O vitamin B12 accelerate a large range of important reactions NH2 including those involved in producing red blood cells. HN O N HO N O O P O O O CH2OH Moorpark College Department of Chemistry Chemistry 11 Lab Manual Table of Contents Laboratory Experiments Page Number Experiment 1 – Separation of Copper(II) Sulfate from Sand ............................................. 3 Experiment 2 – Measurements............................................................................................ 6 Experiment 3 – Properties of Solutions ............................................................................ 13 Experiment 4 – Double Displacement Reactions ............................................................. 20 Experiment 5 – Single Displacement Reactions ............................................................... 25 Experiment 6 – Precipitation of Strontium Sulfate ........................................................... 29 Experiment 7 – Ionization and the Nature of Acids, Bases, and Salts .............................. 33 Experiment 8 – Acid/Base Titrations ................................................................................ 42 Experiment 9 – Structure in Inorganic & Organic
    [Show full text]
  • Laboratory Equipment Used in Filtration
    KNOW YOUR LAB EQUIPMENTS Test tube A test tube, also known as a sample tube, is a common piece of laboratory glassware consisting of a finger-like length of glass or clear plastic tubing, open at the top and closed at the bottom. Beakers Beakers are used as containers. They are available in a variety of sizes. Although they often possess volume markings, these are only rough estimates of the liquid volume. The markings are not necessarily accurate. Erlenmeyer flask Erlenmeyer flasks are often used as reaction vessels, particularly in titrations. As with beakers, the volume markings should not be considered accurate. Volumetric flask Volumetric flasks are used to measure and store solutions with a high degree of accuracy. These flasks generally possess a marking near the top that indicates the level at which the volume of the liquid is equal to the volume written on the outside of the flask. These devices are often used when solutions containing dissolved solids of known concentration are needed. Graduated cylinder Graduated cylinders are used to transfer liquids with a moderate degree of accuracy. Pipette Pipettes are used for transferring liquids with a fixed volume and quantity of liquid must be known to a high degree of accuracy. Graduated pipette These Pipettes are calibrated in the factory to release the desired quantity of liquid. Disposable pipette Disposable transfer. These Pipettes are made of plastic and are useful for transferring liquids dropwise. Burette Burettes are devices used typically in analytical, quantitative chemistry applications for measuring liquid solution. Differing from a pipette since the sample quantity delivered is changeable, graduated Burettes are used heavily in titration experiments.
    [Show full text]
  • Product Catalogue
    Lab Equipment 8/6/06 16:22 Page 1 LABORATORY EQUIPMENT © 2003 S Murray & Co Ltd Holborn House Old Woking Laboratory Equipment: Catalogue Surrey GU22 9LB England Registered in England No 145824 This catalogue is copyright and no Telephone +44 (0)1483 740099 part of it may be reproduced Authorised Share Capital Fax +44 (0)1483 755111 without our express written consent. £1,000,000 e-mail [email protected] Produced by Knowles Thompson. Printed in the UK. www.smurray.co.uk Lab Equipment 8/6/06 16:22 Page 2 SMURRAY&CO AHISTORY OF G ROWTH &DEVELOPMENT Head office and glassworks, Woking Blow-moulding and printworks, Woking S Murray was founded in 1915, initially as a Woking, and the manufacture of surgical distributor of medical glassware. instruments in Sheffield. The company rapidly developed to become Represented by more than 300 wholesalers a leading British manufacturer of laboratory and distributors worldwide, the SAMCO consumables and has since diversified into trademark is known internationally for blow-moulding and silk-screen printing at quality, service and competitive pricing. 2 Lab Equipment 8/6/06 16:22 Page 3 SMURRAY&CO AFIRM F OUNDATION FOR THE F UTURE Sheffield factory Notable Milestones Laboratory Equipment Owner managed for four generations, S Murray Manufacture of test tubes was relocated from & Co has a history of growth and development London to Woking in 1941. The company with a number of notable milestones:- commenced distribution of Trident Vials in 1964 and acquired laboratory scaffolding Plastic Containers manufacturer Climpex Ltd in 1998. Beginning with the distributorship of Fibrenyle Surgical Instruments products in 1963, the company commenced The acquisition of Sheffield-based surgical in-house manufacture in 1984, then acquired and dissecting instrument manufacturers blow-moulding and silk-screen specialists George Gill & Sons took place in 1948, Miller Mouldings Ltd in 1989.
    [Show full text]