SERIAL # GOODNATURE M-1 OWNER’S MANUAL SETUP & OPERATING INSTRUCTIONS Introduction

WARNING: To limit risk of personal injury and material damage, all users must read these instructions in their entirety and strictly follow them.

Check out our YouTube channel at youtube.com/goodnaturepro for video guides and how-to’s, which we update regularly.

You can find tips and solutions to many common questions on our knowledgebase at: www.goodnature.com/knowledgebase

MACHINE SPECIFICATIONS

VAC: 115V | Amps: 8A | Frequency: 60Hz Single phase | IPX1 | Weight: 65 lb

APPLICATION

The M-1 is a commercial press built specifically for juice on-demand. No longer do you or your customers have to choose between “fresh” or “cold-pressed”—now there can be both. The first juice press that requires no cleaning between recipes.

HERBIVORE™ WHOLEFRUIT READYGRIND™ FRESHFILTER® PRESSAFE ELEGANT GRINDER HOPPER™ TECHNOLOGY PRESS BAGS INTERLOCKS™ DESIGN

GOODNATURE M-1 OWNER’S MANUAL 02 SETUP & OPERATING INSTRUCTIONS 28 Table of Contents

SECTION 1 Safety Precautions PAGE 04

SECTION 2 Unpacking PAGE 05

SECTION 3 Enclosed Parts List PAGE 06

SECTION 4 Setup PAGE 07

SECTION 5 Produce Preparation PAGE 16

SECTION 6 Operation PAGE 17

SECTION 7 Cleaning PAGE 20

SECTION 8 Maintenance PAGE 22

SECTION 9 Warranty PAGE 23

SECTION 10 Replacement Parts PAGE 26

SECTION 11 Contact Information PAGE 27

GOODNATURE M-1 OWNER’S MANUAL 03 SETUP & OPERATING INSTRUCTIONS 28 Section 1: Safety Precautions

DANGER: This machine is not intended for use by persons (including children) with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the machine by a person responsible for their safety.

DANGER: Never place hands, body parts, clothing, hair or any foreign object in the machine while it is operating. Failure to do so can result in bodily harm, or damage to the machine.

WARNING: Disconnect all power before performing maintenance to avoid risk of serious electric shock and mechanical hazards.

WARNING: Always check with your local health department regarding procedures required to ensure proper cleaning and sanitation in order to avoid serious food borne illness to consumers. For the US: FDA.gov/food.

WARNING: Discontinue use immediately and have machine serviced if any components are damaged or malfunctioning to avoid risk of personal injury and damage to the machine.

WARNING: Never tamper with or override any of the safety features of the machine, including the Hopper Door. Tampering with safety features can result in unsafe operating conditions and can result in harm to the operator.

WARNING: Be aware of all pinch points and moving parts, and take precautions to keep loose clothing, hair, or foreign objects away from them to avoid personal injury and damage to the machine.

CAUTION: Only place machine on a sturdy counter, table, or cart with locked casters.

GOODNATURE M-1 OWNER’S MANUAL 04 SETUP & OPERATING INSTRUCTIONS 28 Section 2: Unpacking

PREASSEMBLY STEPS

1 Inspect the shipping container of your new M-1 prior to opening. Ensure it is free of any handling damage that may have occurred during shipping. Notify the shipping carrier of any damage to the shipping container as soon as it is received.

2 Release the four plastic clips from the base of the shipping container by pinching the sides together and pulling out. Clip

3 Lift the outer box directly up.

4 Remove the top box.

5 Remove the storyboard box.

6 Unfasten the Velcro® strap that is over the machine.

7 Remove the FreshFilter® Press Bags, Toolkit, and any other loose items.

8 Lift machine away from the shipping container base and onto the counter, table, or cart where it is intended to be used. Machine should be lifted by a minimum of two people. One person can lift from underneath the front two feet, and one person can lift from the rear two feet.

9 We recommend cleaning all parts that will be in contact with food prior to its first use. The cleaning procedure is located in section 7 of this manual.

10 Prior to applying any electrical power to the equipment, complete all of the setup steps outlined in Section 4.

11 Review the enclosed parts list on the following page. Inspect all enclosed parts carefully and make sure that there are no parts missing. If any parts are missing or damaged please contact Goodnature.

GOODNATURE M-1 OWNER’S MANUAL 05 SETUP & OPERATING INSTRUCTIONS 28 Section 3: Enclosed Parts List

Hopper Base Hopper Hopper Door

Grinder Blade Pusher Press Chamber

Press Rack Moving Platen FreshFilter® Press Bags

Drip Tray Tool Kit & Accessories

GOODNATURE M-1 OWNER’S MANUAL 06 SETUP & OPERATING INSTRUCTIONS 28 Section 4: Setup

READYGRIND™ KIT SETUP

GOODNATURE M-1 OWNER’S MANUAL 07 SETUP & OPERATING INSTRUCTIONS 28 Section 4: Setup

1 2 3

Attach Hopper Door to the Hopper Position the Grinder Blade onto the Position Hopper on the Hopper Base by inserting the Hopper Door Hopper Base. Base by aligning the Hopper knobs into the cutouts on the Hopper slightly offset from the Hopper Base, holding completely open. Base so that the cutouts line up with the tabs on the Hopper Base, twist clockwise on Hopper Base until it locks into place.

4 5

Insert the Pusher all the way into With the Grinder Motor Housing the Hopper, the Pusher Handle is in the UP position, place the tapered in order to allow the hopper assembled ReadyGrind™ Kit onto door to open and close with the the four posts of Grinder Motor Pusher installed all the way into Housing, and twist clockwise to the Hopper. Close the Hopper Door. lock.

GOODNATURE M-1 OWNER’S MANUAL 08 SETUP & OPERATING INSTRUCTIONS 28 Section 4: Setup

PRESS KIT SETUP

GOODNATURE M-1 OWNER’S MANUAL 09 SETUP & OPERATING INSTRUCTIONS 28 Section 4: Setup

1 2 3 4

Insert the Press Insert the Moving Place the assembled Press Move the Drip Tray into Rack into the Press Platen into the Press Kit into the press area of the position under the press area of Chamber. The Press Chamber with the machine. The Press Chamber the machine. It will stop when it Rack will fold to allow draining grooves facing should rest on top of the Fixed makes contact with the front of alignment of the forward towards the Platen and the side rails of the machine. bottom tab with the front of the press and the press. Slide the Moving cutout in the bottom with the bill on top. Platen to the back of the Press left of the Press Chamber. Chamber.

GOODNATURE M-1 OWNER’S MANUAL 10 SETUP & OPERATING INSTRUCTIONS 28 Section 4: Setup

5 6 7

Place one FreshFilter® Press Bag into Open the top of the bag so that the Lower the grinder to the the Press Chamber. excess material rests on the front DOWN position. of the Press Chamber and on the Moving Platen.

GOODNATURE M-1 OWNER’S MANUAL 11 SETUP & OPERATING INSTRUCTIONS 28 Section 5: Produce Preparation

Visit www.goodnature.com/knowledgebase and go to the Juicing Tips section for more information on preparing produce for juice.

CAUTION: Only press produce that has been shredded. Never attempt to press unshredded produce, pits, or large seeds, as doing so can put uneven loading on the machine and cause damage.

GOODNATURE M-1 OWNER’S MANUAL 12 SETUP & OPERATING INSTRUCTIONS 28 Section 6: Operation

POWER SWITCH

GOODNATURE M-1 OWNER’S MANUAL 13 SETUP & OPERATING INSTRUCTIONS 28 Section 6: Operation

CONTROLS

There are three buttons on the right side of the machine that are used to operate the grinder and press. These buttons are GRIND, PRESS and STOP.

There are six lights on the button panel:

Drop Three functional lights next to each button that will illuminate during operation.

Drop Three safety indicator lights at the bottom of the Button Panel.

1 Hopper Door is closed and the“Hopper Door Safety” is engaged.

2 Grinder is lowered into the DOWN position and the “Grinder Safety” is engaged.

3 Press Kit is properly installed and the “Chamber Safety” is engaged.

GOODNATURE M-1 OWNER’S MANUAL 14 SETUP & OPERATING INSTRUCTIONS 28 Section 6: Operation

GRIND

Drop Pressing GRIND will start the grind cycle.

Drop Press the GRIND button a second time to stop the grind cycle. Alternatively, the STOP button can be pressed to stop the grinder.

Drop When the Hopper Door is opened to add produce during the cycle, the grinder will come to a stop automatically and the GRIND light will flash. The grind cycle will restart automatically once the door is closed.

• If the hopper door is open for more than 45 seconds or the Grinder runs without interruption, the grind cycle will cancel and the light will no longer be illuminated.

• Use the GRIND button to stop the grinder before opening Hopper Door when the Hopper is full.

Drop A solid illuminated GRIND light means that the Grinder Blade is spinning.

PRESS

Drop Pushing the PRESS button starts the pressing cycle. It is intended for making a single serving of juice, 1 - 2.5 lb of produce, depending on the recipe.

Drop The pressing cycle will take roughly 90 seconds. At the end of the press cycle, the press will automatically relieve pressure and the press rod will retract into the machine.

Drop To cancel a press cycle use the PRESS or STOP buttons. This will start a retract of the press rod and cancel the current press cycle.

STOP

Drop Pressing the STOP button while the grinder is running will turn off the grinder.

Drop Pressing the STOP button once during any press cycle or while the machine is idle and powered on will relieve any pressure and retract the press rod.

GOODNATURE M-1 OWNER’S MANUAL 15 SETUP & OPERATING INSTRUCTIONS 28 Section 6: Operation

PRE-OPERATION CHECKS

Drop Ensure the ReadyGrind™ Kit and the Press Kit are properly assembled according to Section 4: Setup

Drop Check that the press rod is fully retracted into the machine (this can be done by powering the machine on and pressing the STOP button).

Drop Check that the Moving Platen is pushed snugly to the back of the Press Chamber.

Drop Recipe is prepared, 1-2.5 lb of produce, depending on your recipe.

TROUBLESHOOTING TIP:

If the grinder does not start and the Hopper Door safety indicator light at the bottom left of the button panel is blinking then open the Hopper Door and then close it. The Hopper Door safety indicator light should turn on and be solidly illuminated. Press the GRIND button to start a grind cycle.

GOODNATURE M-1 OWNER’S MANUAL 16 SETUP & OPERATING INSTRUCTIONS 28 Section 6: Operation

OPERATION

1 2 3

Plug the M-1 Power Cord into the Push the power switch to the ON Place an empty cup on the receptacle located on the back of the ( I ) position. You will hear the Drip Tray. machine. With the machine power turn on once the machine has switch in the OFF ( O ) position, plug power. the power cord into a wall outlet.

4 5 6

Check that all three bottom lights Push the GRIND button to turn on Pull the Pusher out until it on the Button Panel are illuminated. the grinder. stops and rest the Pusher in This indicates that all three safeties the notch on the Hopper as are in the correct position. shown.

GOODNATURE M-1 OWNER’S MANUAL 17 SETUP & OPERATING INSTRUCTIONS 28 Section 6: Operation

7 8 9

Fill the Hopper, up to 2/3 full, with Close the Hopper Door by lowering Place one hand on the Hopper the desired produce. the Pusher. Be sure the Hopper Door applying firm pressure, Door is completely closed. and with the other hand, apply gentle pressure to the Pusher. The produce will grind slowly into the press bag. Some vibration in the grinder and Pusher is normal. Continue grinding produce until the Hopper is empty.

Pro Tips:

If it seems that the Pusher 10 11 is not making any progress, twist the pusher clockwise and Once grinding is complete, push the Before starting the press cycle, counterclockwise until the blockage is cleared. GRIND or STOP button to turn off check to make sure the press bag is the grinder. evenly filled and is not over-filled. At the end of the grind cycle, Push the PRESS button to begin the press cycle. twist the pusher clockwise, 1-2 full turns. This will ensure that the Hopper is cleared of produce.

GOODNATURE M-1 OWNER’S MANUAL 18 SETUP & OPERATING INSTRUCTIONS 28 Section 6: Operation

12 13 14

The press will stop Your juice is ready to serve! If switching quickly to a new automatically when the cycle is recipe, swap out ReadyGrind™ Kit finished, about 90 seconds. At with a clean one, replace the press the end of the cycle, move the bag, and you are ready to go. grinder to the UP position, then push the moving platen back away from the press bag filled with pulp and remove the press bag from the press chamber.

Pro Tip:

If you are testing a recipe for the first time, have an extra cup or container on hand and be prepared to catch any possible overflow. 15

When you are finished, turn the power switch to the OFF (O) position.

GOODNATURE M-1 OWNER’S MANUAL 19 SETUP & OPERATING INSTRUCTIONS 28 Section 7: Cleaning

CLEANING

WARNING: Turn power switch to the “Off” position and disconnect all power before performing maintenance to avoid risk of serious electric shock.

WARNING: Always check with your local health department regarding procedures and regulations required to ensure proper cleaning and sanitation in order to avoid serious foodborne illness.

WARNING: Do not put the machine in a sink or wash basin.

NOTICE: Cleaning with a water spray or jet will cause damage to the machine.

DISHWASHER SAFE PARTS

Hopper Base Hopper Hopper Door Grinder Blade Pusher

Press Chamber Press Rack Moving Platen Drip Tray

GOODNATURE M-1 OWNER’S MANUAL 20 SETUP & OPERATING INSTRUCTIONS 28 Section 7: Cleaning

Follow manufacturer’s instructions for use of chemicals for cleaning and sanitizing food contact surfaces and verify that they are approved by your local health authority. Follow your local health department’s procedures and regulations regarding cleaning and sanitizing.

Wash, rinse, and sanitize all food contact surfaces of cold press juicer:

1 After each use.

2 Any time contamination occurs or is suspected.

3 At a minimum of once every four hours while the machine is in use.

Wash, rinse, and sanitize food contact surfaces in adherence to local health regulations. We recommend the following procedure:

Drop Wash surface with a detergent solution.

Drop Rinse the surface with clean water.

Drop Sanitize surface using a sanitizing solution mixed at a concentration specified on the manufacturer’s label.

Drop Place wet items in a manner to allow air drying.

GOODNATURE M-1 OWNER’S MANUAL 21 SETUP & OPERATING INSTRUCTIONS 28 Section 7: Cleaning

DISASSEMBLY AND CLEANING THE PARTS

1 Turn the power switch to the OFF position.

2 Remove the ReadyGrind™ Kit by twisting counterclockwise and lifting up and off.

3 Simply rinse out or if finished juicing, disassemble and wash.

4 Remove Press Kit, lift up and out.

5 Simply rinse out or if finished juicing, disassemble and wash.

6 Remove the Drip Tray and wash.

7 Wipe down the machine with a wet cloth then wipe dry. Sanitize machine and all parts according to your local health department’s regulations. Do not spray machine.

GOODNATURE M-1 OWNER’S MANUAL 22 SETUP & OPERATING INSTRUCTIONS 28 Section 8: Maintenance

WARNING: Disconnect all power before performing maintenance to avoid risk of electrical shock.

DAILY MAINTENANCE

Drop Check machine for worn or damaged components, and proper functioning of the machine.

Drop If the machine is not functioning as described in this manual, please discontinue use immediately and contact technical support. For up-to-date support information go to www.goodnature.com/support.

MONTHLY MAINTENANCE

Drop With the machine ON and all components still in place, push the PRESS button and allow the press rod to extend. Once extended, move the grinder to the UP position. Clean the press rod with a wet cloth then wipe dry. Apply food grade oil to the press rod. Press the STOP button to retract the press rod. Apply food grade oil to the press rod, we recommend Super Lube (R) H3 Food Grade Lightweight OIL, ISO 68.

Drop Check machine for loose fasteners.

GOODNATURE M-1 OWNER’S MANUAL 23 SETUP & OPERATING INSTRUCTIONS 28 Section 9: Warranty

Warranty information was provided during the purchase of the equipment, and is part of the Purchase and Sale agreement. If you need a replacement copy please contact Goodnature Products, Inc. or your sales representative regarding warranty information.

Altering the machinery in any way not described in this manual will void the warranty. Failure to follow the operating instructions defined in this manual will void the warranty. Warranty is not transferable.

Section 10: Replacement Parts

For easy ordering of replacement parts, visit our online shop at https://www.goodnature.com/products/ Section 11: Contact Information

Goodnature Products, Inc. 149 Bud Mil Drive Buffalo, NY 14206

1-800-875-3381 [email protected] www.goodnature.com

For up to date support information, visit www.goodnature.com/support.

You can find juicing tips and solutions to many common questions on our knowledgebase at: www.goodnature.com/knowledgebase

Check out our YouTube channel at youtube.com/goodnaturepro for video guides and how-to’s, which we update regularly.

GOODNATURE M-1 OWNER’S MANUAL 24 SETUP & OPERATING INSTRUCTIONS 28 COMMERCIAL COLD PRESSED JUICER 25276_R05