SERIAL # GOODNATURE M-1 OWNER’S MANUAL SETUP & OPERATING INSTRUCTIONS Introduction WARNING: To limit risk of personal injury and material damage, all users must read these instructions in their entirety and strictly follow them. Check out our YouTube channel at youtube.com/goodnaturepro for video guides and how-to’s, which we update regularly. You can find juicing tips and solutions to many common questions on our knowledgebase at: www.goodnature.com/knowledgebase MACHINE SPECIFICATIONS VAC: 115V | Amps: 8A | Frequency: 60Hz Single phase | IPX1 | Weight: 65 lb APPLICATION The M-1 is a commercial juice press built specifically for juice on-demand. No longer do you or your customers have to choose between “fresh” or “cold-pressed”—now there can be both. The first juice press that requires no cleaning between recipes. HERBIVORE™ WHOLEFRUIT READYGRIND™ FRESHFILTER® PRESSAFE ELEGANT GRINDER HOPPER™ TECHNOLOGY PRESS BAGS INTERLOCKS™ DESIGN GOODNATURE M-1 OWNER’S MANUAL 02 SETUP & OPERATING INSTRUCTIONS 28 Table of Contents SECTION 1 Safety Precautions PAGE 04 SECTION 2 Unpacking PAGE 05 SECTION 3 Enclosed Parts List PAGE 06 SECTION 4 Setup PAGE 07 SECTION 5 Produce Preparation PAGE 16 SECTION 6 Operation PAGE 17 SECTION 7 Cleaning PAGE 20 SECTION 8 Maintenance PAGE 22 SECTION 9 Warranty PAGE 23 SECTION 10 Replacement Parts PAGE 26 SECTION 11 Contact Information PAGE 27 GOODNATURE M-1 OWNER’S MANUAL 03 SETUP & OPERATING INSTRUCTIONS 28 Section 1: Safety Precautions DANGER: This machine is not intended for use by persons (including children) with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the machine by a person responsible for their safety. DANGER: Never place hands, body parts, clothing, hair or any foreign object in the machine while it is operating. Failure to do so can result in bodily harm, or damage to the machine. WARNING: Disconnect all power before performing maintenance to avoid risk of serious electric shock and mechanical hazards. WARNING: Always check with your local health department regarding procedures required to ensure proper cleaning and sanitation in order to avoid serious food borne illness to consumers. For the US: FDA.gov/food. WARNING: Discontinue use immediately and have machine serviced if any components are damaged or malfunctioning to avoid risk of personal injury and damage to the machine. WARNING: Never tamper with or override any of the safety features of the machine, including the Hopper Door. Tampering with safety features can result in unsafe operating conditions and can result in harm to the operator. WARNING: Be aware of all pinch points and moving parts, and take precautions to keep loose clothing, hair, or foreign objects away from them to avoid personal injury and damage to the machine. CAUTION: Only place machine on a sturdy counter, table, or cart with locked casters. GOODNATURE M-1 OWNER’S MANUAL 04 SETUP & OPERATING INSTRUCTIONS 28 Section 2: Unpacking PREASSEMBLY STEPS 1 Inspect the shipping container of your new M-1 prior to opening. Ensure it is free of any handling damage that may have occurred during shipping. Notify the shipping carrier of any damage to the shipping container as soon as it is received. 2 Release the four plastic clips from the base of the shipping container by pinching the sides together and pulling out. Clip 3 Lift the outer box directly up. 4 Remove the top box. 5 Remove the storyboard box. 6 Unfasten the Velcro® strap that is over the machine. 7 Remove the FreshFilter® Press Bags, Toolkit, and any other loose items. 8 Lift machine away from the shipping container base and onto the counter, table, or cart where it is intended to be used. Machine should be lifted by a minimum of two people. One person can lift from underneath the front two feet, and one person can lift from the rear two feet. 9 We recommend cleaning all parts that will be in contact with food prior to its first use. The cleaning procedure is located in section 7 of this manual. 10 Prior to applying any electrical power to the equipment, complete all of the setup steps outlined in Section 4. 11 Review the enclosed parts list on the following page. Inspect all enclosed parts carefully and make sure that there are no parts missing. If any parts are missing or damaged please contact Goodnature. GOODNATURE M-1 OWNER’S MANUAL 05 SETUP & OPERATING INSTRUCTIONS 28 Section 3: Enclosed Parts List Hopper Base Hopper Hopper Door Grinder Blade Pusher Press Chamber Press Rack Moving Platen FreshFilter® Press Bags Drip Tray Tool Kit & Accessories GOODNATURE M-1 OWNER’S MANUAL 06 SETUP & OPERATING INSTRUCTIONS 28 Section 4: Setup READYGRIND™ KIT SETUP GOODNATURE M-1 OWNER’S MANUAL 07 SETUP & OPERATING INSTRUCTIONS 28 Section 4: Setup 1 2 3 Attach Hopper Door to the Hopper Position the Grinder Blade onto the Position Hopper on the Hopper Base by inserting the Hopper Door Hopper Base. Base by aligning the Hopper knobs into the cutouts on the Hopper slightly offset from the Hopper Base, holding completely open. Base so that the cutouts line up with the tabs on the Hopper Base, twist clockwise on Hopper Base until it locks into place. 4 5 Insert the Pusher all the way into With the Grinder Motor Housing the Hopper, the Pusher Handle is in the UP position, place the tapered in order to allow the hopper assembled ReadyGrind™ Kit onto door to open and close with the the four posts of Grinder Motor Pusher installed all the way into Housing, and twist clockwise to the Hopper. Close the Hopper Door. lock. GOODNATURE M-1 OWNER’S MANUAL 08 SETUP & OPERATING INSTRUCTIONS 28 Section 4: Setup PRESS KIT SETUP GOODNATURE M-1 OWNER’S MANUAL 09 SETUP & OPERATING INSTRUCTIONS 28 Section 4: Setup 1 2 3 4 Insert the Press Insert the Moving Place the assembled Press Move the Drip Tray into Rack into the Press Platen into the Press Kit into the press area of the position under the press area of Chamber. The Press Chamber with the machine. The Press Chamber the machine. It will stop when it Rack will fold to allow draining grooves facing should rest on top of the Fixed makes contact with the front of alignment of the forward towards the Platen and the side rails of the machine. bottom tab with the front of the press and the press. Slide the Moving cutout in the bottom with the bill on top. Platen to the back of the Press left of the Press Chamber. Chamber. GOODNATURE M-1 OWNER’S MANUAL 10 SETUP & OPERATING INSTRUCTIONS 28 Section 4: Setup 5 6 7 Place one FreshFilter® Press Bag into Open the top of the bag so that the Lower the grinder to the the Press Chamber. excess material rests on the front DOWN position. of the Press Chamber and on the Moving Platen. GOODNATURE M-1 OWNER’S MANUAL 11 SETUP & OPERATING INSTRUCTIONS 28 Section 5: Produce Preparation Visit www.goodnature.com/knowledgebase and go to the Juicing Tips section for more information on preparing produce for juice. CAUTION: Only press produce that has been shredded. Never attempt to press unshredded produce, pits, or large seeds, as doing so can put uneven loading on the machine and cause damage. GOODNATURE M-1 OWNER’S MANUAL 12 SETUP & OPERATING INSTRUCTIONS 28 Section 6: Operation POWER SWITCH GOODNATURE M-1 OWNER’S MANUAL 13 SETUP & OPERATING INSTRUCTIONS 28 Section 6: Operation CONTROLS There are three buttons on the right side of the machine that are used to operate the grinder and press. These buttons are GRIND, PRESS and STOP. There are six lights on the button panel: Drop Three functional lights next to each button that will illuminate during operation. Drop Three safety indicator lights at the bottom of the Button Panel. 1 Hopper Door is closed and the“Hopper Door Safety” is engaged. 2 Grinder is lowered into the DOWN position and the “Grinder Safety” is engaged. 3 Press Kit is properly installed and the “Chamber Safety” is engaged. GOODNATURE M-1 OWNER’S MANUAL 14 SETUP & OPERATING INSTRUCTIONS 28 Section 6: Operation GRIND Drop Pressing GRIND will start the grind cycle. Drop Press the GRIND button a second time to stop the grind cycle. Alternatively, the STOP button can be pressed to stop the grinder. Drop When the Hopper Door is opened to add produce during the cycle, the grinder will come to a stop automatically and the GRIND light will flash. The grind cycle will restart automatically once the door is closed. • If the hopper door is open for more than 45 seconds or the Grinder runs without interruption, the grind cycle will cancel and the light will no longer be illuminated. • Use the GRIND button to stop the grinder before opening Hopper Door when the Hopper is full. Drop A solid illuminated GRIND light means that the Grinder Blade is spinning. PRESS Drop Pushing the PRESS button starts the pressing cycle. It is intended for making a single serving of juice, 1 - 2.5 lb of produce, depending on the recipe. Drop The pressing cycle will take roughly 90 seconds. At the end of the press cycle, the press will automatically relieve pressure and the press rod will retract into the machine. Drop To cancel a press cycle use the PRESS or STOP buttons. This will start a retract of the press rod and cancel the current press cycle. STOP Drop Pressing the STOP button while the grinder is running will turn off the grinder. Drop Pressing the STOP button once during any press cycle or while the machine is idle and powered on will relieve any pressure and retract the press rod.