Reprinted from Packaging Strategies • Copyright© All Rights Reserved BNP Media. As the flexible packaging industry expands, the variety and types of heat sealers have increased to meet the demand. While there are many choices of highly specialized sealing from which to choose, there are only three standard methods for heat sealing: Impulse sealing, direct, or constant heat sealing, and ultrasonic sealing. Understanding the benefits and potential drawbacks of each method can go a long way in helping the purchaser make the most appropriate choice for their particular application.

Impulse heat sealing Impulse heat sealing is excellent for joining materials such as and Polyurethane that require a moderate temperature to establish an effective seal. This versatile meth-od may also be used for sealing Mylar, ®, and a wide variety of other , pouch, and mate- rials. Impulse sealing is often used to seal multi-layer, metalized, and oxygen barrier and pouches. Properly configured, an impulse heat sealer can join two sheets of fairly heavy thermoplastic materials. Impulse heat sealers may have one or two (round or flat) replaceable heating elements made of a specialized material - usually a Nichrome alloy - located in the top and or bottom of the seal-ing bars. The Nichrome element is sandwiched between a resilient, heat resistant rubber pad and a protective Teflon fabric. After the materials is positioned in the sealer jaws, the jaws close and are held in place using pneumatic or mechanical pressure. An electric current then momentar-ily heats the Nichrome element for a predetermined amount of time to achieve the necessary seal-ing temperature. The jaws continue to hold the workpiece in place after the heat cycle is complete (again, for a predetermined amount time) to permit the welded material to cool and fuse fully. Large- ly determined by the material used, sealing usually requires a specific combination of heat, pressure, and time between each step. One of the advantages of impulse sealing is its inherent safety. High heat is only present when the sealing jaws are closed under pressure and the sealing element is energized. This means that it is virtually impossible to become burned upon contact with the sealing jaws. While the jaws can retain a small amount of residual heat over hours of continuous use, the temperature never reaches a danger- ous level. By controlling the temperature of the seal wire, impulse sealing can accomplish everything constant heat can achieve. One key advantage of impulse sealing has to do with the fact that the user can control the cooling cycle while the material is still in the sealing jaws and under pressure. Anoth- er advantage in impulse sealing is the reduction in operating costs. Because the sealing elements are energized for a very short period per cycle, power consumption may be reduced. Lastly, unlike constant heat sealers, impulse sealers can regulate cool times, plus they do not require a “warm-up” period to reach operating temperature.

Constant heat sealing In contrast to impulse sealing where the seal bar temperature rises and falls quickly, constant heat sealing provides a higher controlled temperature at the sealing jaws, making this process more adaptable to certain thermoplastic or coated materials. A constant heat sealer can join two sheets of thermoplastic materials as long as the material does not overheat, causing it to become thin and weak. Like impulse sealers, constant heat sealers use one or two heated sealing bars – but unlike the impulse method, the sealing bars are continuously held at the prescribed sealing temperature at all times. Once they have reached operating temperature, constant heat sealers can maintain an accurate level of tem- perature control in the sealing bars. Though seal bars remain hot, most modern constant heat sealing machines have protective barriers that are designed to reduce or eliminate burn injuries. Constant heat sealers do offer some advantages over impulse sealing. In impulse sealers, the constant heating and cooling cycles can cause stress and deformation of the sealing element unless a temperature controller is used, which limits the wire deterioration. Constant heat sealing can reduce repetitive expansion and shrinking. For certain materials (many multi-layer, Mil-Spec bags, for example), constant heat sealing is the preferred approach as heat is readily available at high temperatures.

Ultrasonic heat sealing Ultrasonic sealing is a technique developed in the 1960s, whereby pressure and high-fre- quency vibrations are applied to two pieces of material (often rigid plastic) to establish a seal or weld. While not widely used in the flexible packaging industry, ultrasonic sealing is commonly used for joining plastics components in the automotive, aerospace, and consumer products industries as well as in many other industrial applications where rigid plastic is required. One of the advantages of ultra- sonic sealing is the ability to bond dissimilar materials – including plastic to metal and plastic to car- bon fiber materials. In order to bond the materials, ultrasonic sealers require three main components to resonate and interact at the exact same ultrasonic frequency. The key components are the transducer (sometimes called a converter), which transforms an electrical signal into a physical vibration; the booster, which controls or modulates the vibration; and the sonotrode, which transmits the vibration to the workpieces. The benefits of ultrasonic sealing are that it is cleaner and faster than conventional joining methods that use or solvents, plus the low thermal impact on the workpiece facilitates a greater variety of materials that may be joined.

Seal integrity and join strength A critical consideration in the medical device manufacturing industry, seal integrity and join strength can be tested in a number of ways, and the rigor of the test depends on the individual require- ment. It is important to note that there can be some confusion between what constitutes seal strength and seal integrity. A strong seal does not necessarily equate to seal integrity. This is because a seal that passes a standardized strength test may not establish the microbial barrier (due to the presence of channels and voids in the seal) required for sterile barrier device packaging. Heat sealed bags and pouches may be tested for pull strength, the ability to sustain a vacuum, burst strength, seal permea- bility, the ability to maintain a seal under sterilization procedures as well as various other criteria. The current industry standard for sterile barrier testing procedures are described in ASTM F88/F88M-09 (seal strength test), ASTM F2054M-13 (burst testing), and ASTM F1140/1140M-13 (whole-package, internal pressurization). Impulse sealing can be used for all pouches while constant heat can only be used on material, which does not melt. Heat seals are created millions of times per day, around the globe. The success of your sealing processes depend on your understanding of the specific procedures, methods and materials required for achieving a good quality seal for your specific application. << Constant heat sealers are designed for sealing coated , fil and foil laminates, MIL spec barrier bags, and other thick or multi-layer materials. The sealer pictured features a constantly heated, upper seal jaw that is heat-adjustable. The heated seal jaw is shielded for safety. These sealers typically produce wider sealers than impulse sealers but require a bag material that can with- stand elevated temperatures. (Shown: Packaging Aids Constant Heat Sealer)

<< Impulse heat bar sealers are the most common sealing systems. They are very safe and work well with a wide variety of materials. The heating element on top and/or bottom of the sealing bar is heated to a predetermined temperature during the heat cycle. When the heat cycle concludes, a cooling cycle begins. Here, the jaws hold the seal under pressure. Impulse heat bar sealers are known for their ability to produce uniform consistent hermetic seals in the most often used poly films (Shown: Packag- ing Aids Impulse Heat Bar Vacuum Sealer)

Bob Goldberg Marketing Director PAC Machinery San Rafael, CA [email protected] www.pacmachiney.com

Robert Goldberg is a proven B2B expert in market strategy that drives demand, and builds successful, growth-oriented organizations. His work with capital equipment manufacturers focuses on optimizing marketing strategy and aligning organizations to accelerate revenue.

Tyvek® is a registered trademark of DuPont™