DOCSLIB.ORG

ELECTRONIC COUNTERS Plug-On Modular/ Portable Counter System Model 5300 Alb System & 5301A-5312A

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
ELECTRONIC COUNTERS Plug-On Modular/ Portable Counter System Model 5300 Alb System & 5301A-5312A ELECTRONIC COUNTERS Plug-On Modular/ Portable Counter System Model 5300 AlB system & 5301A-5312A 5300 Measuring System Time Base Description Standard crystal frequency: 10 MHz. The 5300 measurement system consists of two mainframes, the Stability 5300A and 5300B; 8 snap-on modules for different measurement Aging rate: < 3 parts in 10'/mo. functions; and snap-between battery pack, digital-to-analog convert­ Temperature: < ± 5 parts in 10',0° to 50°e. er and HP-IB interface modules. Easy-to-use and reliable, this versa­ Typically: < ± 2 parts in 10', 15° to 40°e. tile system allows the user to select the capability wanted now, Line voltage: < ± I part in 10' for 10% line variation. expanding later if needed. Oscillator output: 10 MHz, approximately 1 V rms at rear panel The battery pack provides portable, go anywhere operation with all BNC, 100 Q source impedance. modules. Digital output in BCD format is standard with the 5300A External input: I MHz to 10 MHz, IV rms into 200 Q. mainframe or in ASCII format via the 5312A HP-IB snap-between Opt 001 High Stability Time Base (5300B Only) module (available with 5300B mainframe only). Frequency: 10 MHz. Functions of the snap-on module include frequency to 1.3 GHz and Stability 100 ns time interval and time interval averaging. These are summa­ Aging rate: <1.2 parts in 10'/year. rized in the chart at the bottom of this page. Temperature: <±5 parts in 10',0° to 50°e. Compact and rugged, this system is designed for quick and easy Line voltage: < ± 5 parts in 10' for 10% line variation. owner servicing. On most functional models, immediate checking of Oscillator output: 10 MHz, approximately IV rms at rear panel the basic counter circuits can be done from the front panel. A user­ BNC, 100 Q source impedance. oriented service support package is also available, providing plug-in External input: I to 10 MHz, IV rms into 500 Q. cards with automatic diagnostic routines. General Display: 6-digit, dot matrix (5300A) or 8-digit, 7-segment matrix (5300B), solid state LED display. 5300A and 53008 Measurement System Operating temperature: 0° to 50°e. Mainframe Power requirements: 115 V + 13%. -17% 48-440 Hz; 230 V + The mainframe units provide the system with power, reference fre­ 13%, -17% 48-66 Hz; 25 VA maximum (depends on plug-on mod­ quency, display, counting logic and timing control. ule). Mainframe power without plug-on nominally 5 watts. Battery The 5300A has a 6-digit dot matrix display, standard time base, operation with 5310A re-chargeable battery pack (see 53 lOA external time base input and BCD output as a standard rear panel specifications). output. The 5300B has an 8-digit 7-segment display, standard time Dimensions (with snap-on module): 89 mm H x 160 mm W x 248 base or optional TCXO time base, external time base input and no mm D (3.5" x 6.25" x 9.75"). digital output from the mainframe. See mainframe/plug-on display Digital Output: digital serial, 4-bit BCD parallel standard on 5300A chart below for number of display digits with a particular mainframe mainframe. HP-IB output available on the 5300B using the plug-in and plug-on combination. between 5312A. Time Multimeter High Display Digits Frequency Period Time Interval ACV, DCV, Resolution Model MHz Period Average Interval Average Totalize Ratio n Reciprocal w/5300A w/5300B 5301A 10 • 6 7 5302A 50 • •• • • 6 7 5303B 525 6 8 5304A 10 •• • 6 7 5305B 1300 N/A 8 5306A 10 • 6/5 7/5 5307A 2 • 6 6 5308A 75 • ••• • • N/A 8 ELECTRONIC COUNTERS 5300A/B System (cont.) 5301A 10 MHz Frequency Counter Module Time Interval A to B Input Range: 500 ns to 10' sec. Range: 10 Hz to 10 MHz. Resolution: 100 ns to 10 ms in decade steps. Sensitivity (min): 25 mV rms sine wave 50 Hz to I MHz, 50 mV rms Time interval holdoff: inserts variable delay of approximately 100 sine wave 10 Hz to 10 MHz. fJ.S to 100 ms between START and enabling of STOP; may be dis­ abled. Electrical inputs during delay time are ignored. Frequency Measurement Range: 10 Hz to 10 MHz. Period Average A Gate times: manually selected 0.1, I, or 10 seconds AUTO position Range: 10 Hz to I MHz. selects gate time within I second for maximum resolution. Periods averaged: I to 10' automatically selected. Open/Close (Totalizing): 10 MHz max Frequency A Range: 0 to 10 MHz. 5302A 50 MHz Universal Counter Module Gate times: manually selected 0.1, I, or 10 seconds. AUTO position selects gate time to I second for maximum resolution. Input Channels A and B Range: Channel A, 10 Hz to 50 MHz; Channel B, 10 Hz to 10 MHz. Open/Close (Totalizing): 10 MHz max Sensitivity (min): 25 mV rms sine wave 50 Hz to I MHz. 50 mV rms sine wave 10 Hz to 10 MHz. 100 mV rms sine wave at 50 MHz. 150 53058 1300 MHz Frequency Counter Module mV pop pulse at minimum pulse width, 50 ns. Input Channel A (CW or Burst) Trigger level: selectable positive, negative, or zero volts. Range: 90 MHz to 1300 MHz, prescaled by 16. Marker outputs: rear BNC, TTL low level while gate is open. Sensitivity: 20 mV rms. Impedance: 50 fl. Frequency Attenuator: continuously variable for signals up to 3.5 V rms. Range: Channel A, 10Hz to 50 MHz, prescaled by 10; Channel B, Operating dynamic range: >47 dB 10 Hz to 10 MHz. Gate times: manually selected 0.1, I, or 10 seconds. A UTO position Input Channel B (Normal and High Resolution Mode) selects for maximum resolution within I sec measurement time. Range: 50 Hz to 100 MHz in normal mode. 50 Hz to 10 kHz in high resolution mode. Time Interval A to B Sensitivity: 20 mV rms. Range: 500 nsec to 1000 seconds. Frequency M€lasurement Resolution: 100 ns to I ms in decade steps. Resolution: (selectable) Period B/Period Average B Normal mode: (50 Hz to 1300 MHz): 0.1 Hz to 10,000 Hz. Range: 10Hz to I MHz. High resolution mode: (50 Hz to 10 kHz): 0.0001 to 10 Hz. Resolution: 100 ns to I ms in decade steps. Periods averaged: 1 to 10" automatically selected. 5306A Digital MultimeterI Counter Module DC Voltage Ratio Sensitivity: 100 fJ. V for 10 V range, I mV for 100 V range, 10mV for 7 Display: FB/FA times multiplier (N), N = 10 to 10 • 1000 V range. Range: Channel A: 10 Hz to 1 MHz, Channel B: 10 Hz to 10 MHz. Sample times: normal, 0.5 sec; fast, 0.05 sec. Open/Close (Totalizing): 10 MHz max Effective common mode rejection (1 kfl imbalance): DC, >80 dB; 50 Hz or 60 Hz ± 0.1%, >80 dB. 53038 Frequency Counter Module Normal mode rejection: 50 Hz or 60 Hz ± 0.1 %: > 50 dB. AC Voltage Input Channel A (CW or Burst) Frequency: 40 Hz to 100 kHz for 10 V range, 40 Hz to 500 Hz for Range: DC to 525 MHz, prescaled by 8. 100 V range, 40 Hz to 500 Hz for 1000 V range. Sensitivity (fixed): 100 mV rms sine wave, dc to 500 MHz. 125 mV Effective common mode rejection (1 kfl imbalance): DC, rms sine wave, 500 MHz to 525 MHz. Signal must pass through zero. >80 dB; 50 Hz or 60 Hz ± 0.1%, >50 dB. Input Channel B (CW or Burst) Ohms Range: 50 Hz to 80 MHz, direct. Sensitivity: 0.1 fl for 10 kfl range, 1 fl for 100 kfl range, 100 fl for Sensitivity (automatic): 25 mV rms sine wave, 100 Hz to 50 MHz. 10 Mfl range. 50 mV rms sine wave, 50 Hz to 100 Hz and 50 MHz to 80 MHz. Current through unknown: I mA on 10 kfl range, 100 fJ.A on 100 kfl Sensitivity is adjusted automatically by Automatic Gain Control. range, I fJ.A on 10 Mfl range. Frequency Measurement Frequency Resolution (selectable): I, 10, 100, 1000 Hz. Range: 40 Hz to 10 MHz. Sensitivity (min): 50 mV rms to I MHz; 125 mV rms to 10 MHz. Opt 001; High Stability Time Base (for use with 5300A) Trigger level: automatically adjusts to 40% of peak level of input. Frequency: 10 MHz. Gate times: normal, I sec; fast, 0.1 sec. Stability Aging rate: < 1.2 part in 10'/year. 5307A High Resolution Counter Module Temperature: < ± 5 parts in 107,0 0 to 50°e. Line voltage: < ± 5 parts in 108 for 10% line variation. Input Oscillator output: 10 MHz, approx. IV rms at rear panel BNC. Range: Hz mode, 5 Hz to 2 MHz; CPM mode, 50 to 10 M counts/ External input: I to 10 MHz, IV rms into 500 fl. minute (0.8333 Hz to 166 KHz). Sensitivity (min.): Hz CPM 10 mV rms 5 Hz-1.2 MHz 120 CPM-I0 MCPM 5304A TimerI Counter Module 25 mV rms 1.2 MHz-2.0 MHz 50 CPM-120 CPM Input Channels A and B Pulses: for low duty-cycle pulses « 15%); 15 mV peak for 250 nsec Range: DC coupled, 0 to 10 MHz; AC coupled, 100 Hz to 10 MHz. pulses, 100 mV peak for 100 nsec pulses. Sensitivity (min): 25 mV rms sine wave to 1 MHz, 50 mV rms sine Low pass filters: (3 dB point) 100 Hz 10 kHz wave to 10 MHz, 150 mV pop pulse at minimum pulse width, 40 nsec.
Load more

Recommended publications
  • The 4 States QRP Group HF Test Set Construction Manual
    Copyright 2006, NB6M - Unauthorized Copying or Publication Prohibited The 4 States QRP Group HF Test Set Construction Manual Containing several key pieces of simple Test Equipment that are used to either test or troubleshoot radio circuitry By Wayne McFee, NB6M Revision 0.2 October 21, 2007 Copyright 2006, NB6M - Unauthorized Copying or Publication Prohibited 1 THE HF TEST SET .....................................................................................................................................3 INTRODUCTION............................................................................................................................................3 HF TEST SET SCHEMATIC ...........................................................................................................................5 BOARD LAYOUT..........................................................................................................................................6 PARTS LIST .................................................................................................................................................7 TOOLS AND EQUIPMENT NEEDED................................................................................................................9 PC BOARD, PARTS SIDE ...........................................................................................................................10 PC BOARD, TRACE SIDE...........................................................................................................................11 STARTING
    [Show full text]
  • Keysight 53147A/148A/149A Microwave Frequency Counter/Power Meter/DVM
    Keysight 53147A/148A/149A Microwave Frequency Counter/Power Meter/DVM Assembly Level Service Guide Notices U.S. Government Rights Warranty The Software is “commercial computer THE MATERIAL CONTAINED IN THIS Copyright Notice software,” as defined by Federal Acqui- DOCUMENT IS PROVIDED “AS IS,” sition Regulation (“FAR”) 2.101. Pursu- AND IS SUBJECT TO BEING © Keysight Technologies 2001 - 2017 ant to FAR 12.212 and 27.405-3 and CHANGED, WITHOUT NOTICE, IN No part of this manual may be repro- Department of Defense FAR Supple- FUTURE EDITIONS. FURTHER, TO THE duced in any form or by any means ment (“DFARS”) 227.7202, the U.S. MAXIMUM EXTENT PERMITTED BY (including electronic storage and government acquires commercial com- APPLICABLE LAW, KEYSIGHT DIS- retrieval or translation into a foreign puter software under the same terms CLAIMS ALL WARRANTIES, EITHER language) without prior agreement and by which the software is customarily EXPRESS OR IMPLIED, WITH REGARD written consent from Keysight Technol- provided to the public. Accordingly, TO THIS MANUAL AND ANY INFORMA- ogies as governed by United States and Keysight provides the Software to U.S. TION CONTAINED HEREIN, INCLUD- international copyright laws. government customers under its stan- ING BUT NOT LIMITED TO THE dard commercial license, which is IMPLIED WARRANTIES OF MER- Manual Part Number embodied in its End User License CHANTABILITY AND FITNESS FOR A 53147-90010 Agreement (EULA), a copy of which can PARTICULAR PURPOSE. KEYSIGHT be found at http://www.keysight.com/ SHALL NOT BE LIABLE FOR ERRORS Edition find/sweula. The license set forth in the OR FOR INCIDENTAL OR CONSE- Edition 3, November 1, 2017 EULA represents the exclusive authority QUENTIAL DAMAGES IN CONNECTION by which the U.S.
    [Show full text]
  • Keysight U1251B and U1252B Handheld Digital Multimeter
    Keysight U1251B and U1252B Handheld Digital Multimeter User’s and Service Guide Notices U.S. Government Rights Warranty The Software is “commercial computer THE MATERIAL CONTAINED IN THIS Copyright Notice software,” as defined by Federal DOCUMENT IS PROVIDED “AS IS,” AND Acquisition Regulation (“FAR”) 2.101. IS SUBJECT TO BEING CHANGED, © Keysight Technologies 2009 – 2019 Pursuant to FAR 12.212 and 27.405-3 WITHOUT NOTICE, IN FUTURE No part of this manual may be and Department of Defense FAR EDITIONS. FURTHER, TO THE reproduced in any form or by any Supplement (“DFARS”) 227.7202, the MAXIMUM EXTENT PERMITTED BY means (including electronic storage U.S. government acquires commercial APPLICABLE LAW, KEYSIGHT and retrieval or translation into a computer software under the same DISCLAIMS ALL WARRANTIES, EITHER foreign language) without prior terms by which the software is EXPRESS OR IMPLIED, WITH REGARD agreement and written consent from customarily provided to the public. TO THIS MANUAL AND ANY Keysight Technologies as governed by Accordingly, Keysight provides the INFORMATION CONTAINED HEREIN, United States and international Software to U.S. government INCLUDING BUT NOT LIMITED TO THE copyright laws. customers under its standard IMPLIED WARRANTIES OF commercial license, which is embodied MERCHANTABILITY AND FITNESS FOR Manual Part Number in its End User License Agreement A PARTICULAR PURPOSE. KEYSIGHT U1251-90036 (EULA), a copy of which can be found at SHALL NOT BE LIABLE FOR ERRORS http://www.keysight.com/find/sweula. OR FOR INCIDENTAL OR Edition The license set forth in the EULA CONSEQUENTIAL DAMAGES IN Edition 24, July 26, 2019 represents the exclusive authority by CONNECTION WITH THE FURNISHING, which the U.S.
    [Show full text]
  • 53200A Series RF/Universal Frequency Counter/Timers
    Keysight Technologies 53200A Series RF/Universal Frequency Counter/Timers Data Sheet Imagine Your Counter Doing More! Introduction Frequency counters are depended on in R&D and in manufacturing for the fastest, most accurate frequency and time interval measurements. The 53200 Series of RF and universal frequency counter/timers expands on this expectation to provide you with the most information, connectivity and new measurement capabilities, while building on the speed and accuracy you’ve depended on with Keysight Technologies, Inc. time and frequency measurement expertise. Three available models offer resolution capabilities up to 12 digits/sec frequency resolution on a one second gate. Single- shot time interval measurements can be resolved down to 20 psec. All models offer new built-in analysis and graphing capabilities to maximize the insight and information you receive. More bandwidth Measurement by model Measurements Model Standard Opt MW Inputs – 350 MHz baseband frequency 350 MHz Input (53210A: Ch 2, – 6 or 15 GHz optional microwave Channel(s) 53220A/30A: Ch 3) channels Frequency 53210A, ● ● More resolution & speed 53220A, – 12 digits/sec 53230A – 20 ps single-shot time resolution Frequency ratio 53210A, ● ● – Up to 75,000 and 90,000 53220A, readings/sec (frequency and 53230A time interval) Period 53210A, ● ● More insight 53220A, 53230A – Datalog trend plot Minimum/maximum/ 53210A, ● – Cumulative histogram peak-to-peak input 53220A, – Built-in math analysis and voltage 53230A statistics – 1M reading memory and RF signal strength
    [Show full text]
  • Chapter 26 Oscillator Is Sufficient for Most of Our Needs and Most Amateur Equipment Relies on This Technique
    Test Procedures and Projects 26 his chapter, written by ARRL Technical Advisor Doug Millar, K6JEY, covers the test equipment and measurement techniques common to Amateur Radio. With the increasing complexity of T amateur equipment and the availability of sophisticated test equipment, measurement and test procedures have also become more complex. There was a time when a simple bakelite cased volt-ohm meter (VOM) could solve most problems. With the advent of modern circuits that use advanced digital techniques, precise readouts and higher frequencies, test requirements and equipment have changed. In addition to the test procedures in this chapter, other test procedures appear in Chapters 14 and 15. TEST AND MEASUREMENT BASICS The process of testing requires a knowledge of what must be measured and what accuracy is required. If battery voltage is measured and the meter reads 1.52 V, what does this number mean? Does the meter always read accurately or do its readings change over time? What influences a meter reading? What accuracy do we need for a meaningful test of the battery voltage? A Short History of Standards and Traceability Since early times, people who measured things have worked to establish a system of consistency between measurements and measurers. Such consistency ensures that a measurement taken by one person could be duplicated by others — that measurements are reproducible. This allows discussion where everyone can be assured that their measurements of the same quantity would have the same result. In most cases, and until recently, consistent measurements involved an artifact: a physical object. If a merchant or scientist wanted to know what his pound weighed, he sent it to a laboratory where it was compared to the official pound.
    [Show full text]
  • Agilent Digital Multimeters
    Agilent Digital Multimeters Designed to handle your toughest assignments in various applications Index Measurement Digits of speed (reading/s Basic 1-yr DCV Connectivity & Model Description resolution at 42 digits) accuracy Basic measurements software Page: Benchtop DMM, 42 (U3401A) N/A 0.0120% DCV, ACV, DCI, ACI, N/A 4 dual display 52 (U3402A) 2-wire resistance (4-wire Elegantly simple on U3402A), frequency, and affordable continuity, and diode DMMs with basic and good capabilities U3401A/U3402A 5.5-digit DMM 52 26 0.0250% DCV, ACV, DCI, ACI, USB 2.0, GPIB 5 with built-in 30 W 2- and 4-wire resistance, power supply frequency, continuity, Halves bench/ diode, and capacitance rackspace need 30-W with four output for two instruments ranges, OVP/OCP, auto scan/ramp and square U3606A/U3606B wave generator 5.5 digit bench 52 190 0.0150% DCV, ACV, DCI, ACI, USB 2.0, 6 digital multimeter 2- and 4-wire resistance, Serial Interface OLED dual display frequency, continuity, (RS-232), GPIB diode, capacitance, and DMM Connectivity temperature Utility software (page 24) 34450A Bench/System 62 300/1000 0.0075/0.0035% DCV, ACV, DCI, ACI, USB, LAN/LXI 7 DMM 2- and 4-wire resistance, Core, GPIB, 34401A frequency, period, DMM Connectivity Replacement for continuity, diode, Utility (page 24) accuracy, speed, temperature measurement ease 34460A/34461A and versatility Bench/System 62 1000 0.0035% DCV, ACV, DCI, ACI, GPIB, RS-232, 8 DMM 2- and 4-wire resistance, DMM Connectivity Industry standard frequency, period, Utility software for accuracy, speed, continuity,
    [Show full text]
  • Oscilloscope Selection Guide Oscilloscope Selection Guide
    OSCILLOSCOPE SELECTION GUIDE OSCILLOSCOPE SELECTION GUIDE OSCILLOSCOPE SELECTOR GUIDE Tektronix offers oscilloscopes for many different applications and uses. To help you choose the right scope for your needs, the most common criteria for selecting a scope are listed below, along with helpful tips for determining your requirements. 1 Bandwidth All oscilloscopes have a low-pass frequency response that rolls CONTENTS off at higher frequencies. Oscilloscope bandwidth is specified as CHOOSING YOUR OSCILLOSCOPE 1-3 being the frequency at which a sinusoidal input signal is MIXED SIGNAL AND MIXED DOMAIN OSCILLOSCOPES 4-5 attenuated to 70.7% of the signal’s true amplitude – the -3 dB point. Your oscilloscope must have sufficient bandwidth to MSO/DPO2000B 4 capture all relevant frequency components of your signal. If you MDO3000 4 regularly work with digital signals, it may be easier to consider MDO4000C 5 bandwidth by comparing signal and oscilloscope rise time specifications. Use an oscilloscope with a rise time ADVANCED SIGNAL ANALYSIS OSCILLOSCOPES 6-7 specification five times faster than your signal rise time to MSO/DPO5000B 6 keep error below 2%. 5 Series MSO 6 Rule: Bandwidth > 5 x Highest Signal Frequency DPO7000C Series 7 MSO/DPO70000 Series 7 2 Sample Rate DPO70000SX Series 8 The faster an oscilloscope samples, the greater the resolution SAMPLING OSCILLOSCOPES 8 and detail of the displayed waveform, and the less likely that DSA8300 8 critical information or events will be lost. Tektronix recommends at least 5X oversampling to ensure signal details are captured BASIC OSCILLOSCOPES 9 and to avoid aliasing. TBS1000 9 Rule: Sample Rate > 5 x (Highest Frequency Component) TBS1000B/TBS1000B-EDU 9 TBS2000 9 BATTERY POWERED OSCILLOSCOPES 3 Record Length WITH ISOLATED CHANNELS 10 Record length is the number of samples the oscilloscope can THS3000 10 digitize and store in a single acquisition.
    [Show full text]
  • Build an Rf Frequency Counter Buffer for Hf
    BUILD IT YOURSELF By Dwayne Kincaid WD8OYG BUILD AN RF FREQUENCY COUNTER BUFFER FOR HF Most frequency counters can tolerate only low levels of RF at their input, but here’s a way to safely measure the frequency of an RF signal of up to 200 watts with your existing frequency counter. 36 January/February 2019 ■ FIGURE 1. Block diagram of frequency counter buffer. ■ FIGURE 2. Schematic of frequency counter buffer. his buffer allows you to connect your transceivers. It performs well, is easy to reproduce, counter to any RF source from 20 mW to is low cost, and has a minimal parts count. 200 watts, from 200 kHz to 60 MHz. The Most amateur HF transceivers are in the 5 to circuit has a protection limiter that keeps 200 watt range. This buffer (Figure 2) will allow Tthe RF signal strength in a safe range for the TTL you to connect your standard desktop frequency input of the counter, as well as providing gain for counter directly to the RF line, even with higher weaker signals (Figure 1). signal levels that most frequency counters can You can think of the buffer as a dam safely handle. For Citizens Band, most transceivers are in keeping high water out of Frequency Counter- the 4 to 12 watt range and will work fine with the ville. If the water/signal is too high upstream, buffer. you can limit how much of it gets through. Or, The low end of the buffer’s power range if its strength is too low, you can add some.
    [Show full text]
  • AN200-1 Fundamentals of Microwave Frequency Counters
    H Fundamentals of Microwave Frequency Counters Application Note 200-1 Electronic Counters Series 1 Table of Contents Down-Conversion Techniques for Automatic Microwave Frequency Counters ................................................. 3 Prescaling .................................................................................................... 3 Heterodyne Converter ............................................................................... 4 Transfer Oscillator ..................................................................................... 5 Harmonic Heterodyne Converter ............................................................ 6 Comparing the Principal Microwave Down-Conversion Techniques .................................................................................... 8 Measurement Speed .................................................................................. 8 Accuracy...................................................................................................... 8 Sensitivity and Dynamic Range ............................................................... 10 Signal-to-Noise Ratio ................................................................................. 11 FM Tolerance.............................................................................................. 12 AM Tolerance ............................................................................................. 14 Amplitude Discrimination ........................................................................ 14 Summary of the
    [Show full text]
  • Spectrum Analyzer
    Spectrum Analyzer GSP-9330 USER MANUAL ISO-9001 CERTIFIED MANUFACTURER This manual contains proprietary information, which is protected by copyright. All rights are reserved. No part of this manual may be photocopied, reproduced or translated to another language without prior written consent of Good Will company. The information in this manual was correct at the time of printing. However, Good Will continues to improve products and reserves the rights to change specification, equipment, and maintenance procedures at any time without notice. Good Will Instrument Co., Ltd. No. 7-1, Jhongsing Rd., Tucheng Dist., New Taipei City 236, Taiwan. Table of Contents Table of Contents SAFETY INSTRUCTIONS .................................................. 3 GETTING STARTED .......................................................... 8 GSP-9330 Introduction .......................... 9 Accessories .......................................... 12 Appearance .......................................... 14 First Use Instructions .......................... 26 BASIC OPERATION ........................................................ 38 Frequency Settings ............................... 41 Span Settings ....................................... 45 Amplitude Settings .............................. 48 Autoset ................................................ 62 Bandwidth/Average Settings ................ 64 Sweep .................................................. 70 Trace .................................................... 77 Trigger ................................................
    [Show full text]
  • Frequency Measurements and Mixer
    Frequency Measurements and Mixer Introduction In this laboratory experience the student will measure the frequency of some signal using a frequency counter and a frequency translating device (mixer). Available instrumentation For this practical session you will use the following instrumentation: waveform generator (Hameg 8130, Hameg 8131 or similar) LED signal generator (output C and D, 5 MHz) analog oscilloscope frequency counter (Hameg HM 8122 or similar) For manuals and documentation: http://led.polito.it/main it/instrumentation.asp or see the “Addendum” at the end of these pages Mixer The internal scheme and the pins of the mixer are shown in figures 1 and 2. Figure 1: simplified scheme of the SBL-3 mixer Figure 2: pin scheme for the SBL-3 mixer (as seen from the top) Frequency measurements You can measure the frequency of the signals indicated in table I with the frequency counter. Following the manual instructions you must evaluate the uncertainty. For the trigger related uncertainty you can use a S/N value of 80dB. What’s happen to the trigger uncertainty if the S/N is reduced to a value of 40dB? Table I: frequency measurements Signal f /Hz f /Hz 1 kHz from waveform generator 15 kHz from waveform generator 5 MHz from waveform generator 5 MHz from LED sign.gen. output C 5 MHz from LED sign.gen. output D Frequency difference measurement Compute the frequency difference between output C and output D, starting from the measurements you reported on the table I. Now you can evaluate the uncertainty of the frequency difference.
    [Show full text]
  • Electronic Measurement & Measuring Instruments Syllabus
    ELECTRONIC MEASUREMENT & MEASURING INSTRUMENTS SYLLABUS Module-I (12 Hours) Basics of Measurements: Accuracy, Precision, resolution, reliability, repeatability, validity, Errors and their analysis, Standards of measurement. Bridge Measurement: DC bridges- wheatstone bridge, AC bridges – Kelvin, Hay, Maxwell, Schering and Wien bridges, Wagner ground Connection. Electronic Instruments for Measuring Basic Parameters: Amplified DC meter, AC Voltmeter, True- RMS responding Voltmeter, Electronic multi-meter, Digital voltmeter, Vector Voltmeter. Module-II (12 Hours) Oscilloscopes: Cathode Ray Tube, Vertical and Horizontal Deflection Systems, Delay lines, Probes and Transducers, Specification of an Oscilloscope. Oscilloscope measurement Techniques, Special Oscilloscopes – Storage Oscilloscope, Sampling Oscilloscope. Signal Generators: Sine wave generator, Frequency – Synthesized Signal Generator, Sweep frequency Generator. Pulse and square wave generators. Function Generators. Module-III (10 Hours) Signal Analysis: Wave Analyzer, Spectrum Analyzer. Frequency Counters: Simple Frequency Counter; Measurement errors; extending frequency range of counters Transducers: Types, Strain Gages, Displacement Transducers. Module-IV (6 Hours) Digital Data Acquisition System: Interfacing transducers to Electronics Control and Measuring System. Instrumentation Amplifier, Isolation Amplifier. An Introduction to Computer-Controlled Test Systems.IEEE-488 GPIB Bus Text Books: 1. Modern Electronics Instrumentation & Measurement Techniques, by Albert D.Helstrick and William D.Cooper, Pearson Education. Selected portion from Ch.1, 5-13. 2. Elements of Electronics Instrumentation and Measurement-3rd Edition by Joshph J.Carr.Pearson Education. Selected portion from Ch.1,2,4,7,8,9,13,14,18,23 and 25. Reference Books : 3. Electronics Instruments and Instrumentation Technology – Anand, PHI 4. Doebelin, E.O., Measurement systems, McGraw Hill, Fourth edition, Singapore, 1990. MODULE –I Chapter 1. Basics of Measurements 1.
    [Show full text]