XBOX-01 XBOX360 KINECT Sensor Wall Mounts

INSTALLATION INSTRUCTIONS

XBOX360 KINECT Sensor Wall Mounts Model: XBOX-01 NOTE: Please read Instruction Manual prior to installation. Component Checklist

Please ensure you have received all parts listed on the component checklist prior to installing. If any parts are missing or faulty, contact your local distributor for replacement. WARNING

• Do not begin installation until you have read and understood the instructions and warnings contained in this manual. If you need further assistance, please contact your local distributor.

• Please refer to manufacture’s installation guide for recommended distance from wall to avoid risk of property damage. wall plate (x1) base platform (x1) sensor base (x1) A B C • This product should only be installed by someone of good mechanical aptitude and basic building experience to avoid malfunction. Package W • Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components.

• Always use an assistant or mechanical lifting equipment to safely lift and position ST3.5x32 (x4) concrete anchor (x4) W-A W-B equipment.

Tools required • Tighten screws firmly, but do not over tighten. Over tightening can damage the items, ·Phillips Head Screw driver(200mm length exclude the handle) greatly reducing their holding power. ·Electric drill and 6mm masonry bit for concrete wall installation ·Marking Pen ·Hammer • This product is for indoor use only. (Use of this product outdoors could lead to product failure and personal injury).

1 2 1a WOOD WALL MOUNTING: 1b SOLID BRICK AND CONCRETE BLOCK MOUNTING:

WARNING WARNING

• When installing wall mounts on cinder block, verify that you have a minimum of 1-3/8” of actual concrete thickness in the hole to be used for the concrete anchors. • Make sure that the supporting surface will safely support the combined load of the Do not drill into mortar joints! Be sure to mount in a solid part of the block, generally equipment and all attached hardware and components. 1” minimum from the side of the block. It is suggested electric drill on slow setting • Tighten screws firmly, but do not over tighten. Over tightening can damage the is used to drill the hole instead of a hammer drill to avoid breaking out the back of screws, greatly reducing their holding power. the hole when entering a void or cavity.

• Make sure to have a minimum of 1/3" thickness for the wood wall. • Installer must verify that the supporting surface will safely support the combined load of the equipment and all attached hardware and components.

• Place wall plate on wall as a template. And mark the center of the four mounting holes. • Use the wall plate as a template to mark four holes locations on the wall as shown in fig.1.2. Make sure • Drill four 1/12” (2mm) dia. Holes 3/5” (15mm) deep. Secure the wall plate using four screws (W-A) as shown the wall plate is level. in fig. 1.1. • Pre-drill these holes with a 6mm masonry bit to at least 40mm in depth. Insert a concrete anchor (W-B) into each of these holes. Attach the wall plate to the wall using four screws (W-A) as shown in fig.1.3.

W-B

W-A W-A

fig. 1.1 fig. 1.2 fig. 1.3

3 4 Installing The Base Platform Insert the sensor base with attached XBOX360 KINECT Sensor into the base platform until you hear a 2 “click” as shown in fig.3.2. After the wall plate has been safely secured to the wall. Insert the base platform into the wall plate as shown in fig.2.1.

fig. 2.1 3 Installing XBOX360 KINECT Sensor • Take the sensor base and line it up with the base of the XBOX360 KINECT Sensor. • Press in both grips on the sensor base and fit the sensor base onto the bottom of the XBOX360 KINECT Sensor. Release the grips of the sensor base to lock the two together as shown in fig.3.1.

XBOX360 KINECT Sensor fig. 3.2 is not included. 4 Removing The Sensor Base With Attached XBOX360 KINECT Sensor. To remove the sensor base with attached XBOX360 KINECT Sensor, pull the sensor base switch forward and remove the sensor base with attached XBOX360 KINECT Sensor from the base platform as shown in fig.4.1. Note: the sensor base switch is pointed at the back.

fig. 3.1 fig. 4.1

5 6