Falcon F-Series Keyed Locks Installation Instructions

*030690-000-70* F-Series 030690-000-70 Keyed Locks Installation Instructions

ROSE

INSIDE LEVER

UL OUTSIDE LATCH #10-32 LEVER SHIELD * MACHINE ASSY SCREWS INSIDE SPINDLE ASSY

* NOTE: UL LATCH SHIELD IS ONLY #8 COMBO REQUIRED WITH UL LATCHES SCREWS LATCH ASSY

1. MARK DOOR 2. DOOR PREPARATION 3. INSTALL STRIKE NOTCHES A. Mark height line on edge of door A. Use strike locating tool or pointed approximately 38” from floor. A. Bore 2¹⁄₈” object to locate position for hole in frame. B. Using the proper backset, mark 2¹⁄₈” hole on ³⁄₄ hole thru from B. Bore 1” x ” deep hole. Use strike as a both sides of the door. both sides of template and mortise to the proper depth. C. On the outside of door, mark notches. door to prevent C. If dust box is to D. Mark the center of the door edge for the latch. splintering door be used, clear area finish. with wood chisel. B. File notches on 1” HOLE outside of door being careful not to exceed the 2¹⁵⁄₃₂" dimension. C. Bore 1” hole for latch on door edge. 2¹⁄₈” D. Using the latch faceplate as a HOLE guide, trace outline and mortise door edge so latch is flush with door. NOTE: Hollow metal doors must be properly reinforced for lock support. If support was not furnished contact door manufacturer.

4. INSTALL LATCH SHIELD 6. INSTALL OUTER TRIM 7. INSTALL INNER SPINDLE FOR UL LATCH OPTION ONLY A. Align spindle with latch unit ASSEMBLY and insert outer trim into door. A. Insert latch shield A. Align spindle assembly with square CAUTION: (closed end first) shaft and slide into place. from the outside of the door. Failure to use the latch NOTE: Locking button must be positioned shield with a UL latch will towards the edge of the door. invalidate the UL listing of B. Secure with two screws provided. this product.

5. INSTALL LATCH A. Insert latch into door, making certain that locking button bevel faces direction of closing door. B. Secure with two #8 combo screws provided.

IMPORTANT: FIRST: ¹⁄₈ NOTCHES REQUIRED BORE 2 ” (54mm) HOLE AT CORRECT BACKSET SECOND: IN EXTERIOR SIDE OF DOOR FOR LOCK TO BORE LATCH HOLE MOUNT & FUNCTION PARALLEL TO PROPERLY. SIDES 1” (25mm) DISTANCE FROM EDGE FOLD ALONG EDGE OF DOOR OF DOOR HEIGHT 2³⁄₄” 2³⁄₄” (BACKSET) LINE (70mm) (60mm) ⁵⁄₃₂” (4mm) x 2¹⁵⁄₃₂” ³⁄₃₂ (63mm) ” (2mm) Center Center DEEP MAX for 1³⁄₈” for 1³⁄₄” (35mm) (44mm) RECOMMENDED TEMPLATE INSTRUCTIONS MUST DOORS DOORS BE FOLLOWED TO ASSURE PROPER FUNCTION REMOVE TEMPLATE FROM INSTRUCTIONS

8. INSTALL INSIDE TRIM 9. REMOVING STANDARD 10. INSTALLING STANDARD A. Snap rose over mounting plate. CYLINDERS & LEVERS CYLINDERS & LEVERS B. Place lever on spindle and slide to A. Insert key and turn 90° A. Insert cylinder into lever. locking button. counter-clockwise to unlock lockset. B. Insert key into cylinder. C. Push lever in until button engages B. Depress locking button and pull off lever C. With notches of key facing up, align hole in hole in lever. and cylinder. lever with locking button on spindle assy and D. Check function before closing door. slide lever to locking button. MOUNTING D. Push lever until lever engages button. PLATE E. Check function before closing door.

ROSE

LOCKING BUTTON LOCKING LOCKING BUTTON BUTTON HOLE LEVER

11. REMOVING IC CORE 13. INSTALL IC LEVERS 14. TAILPIECE INSTALLATION

A. Unlock lockset. A. Slide tailpiece assembly into spindle, A. Insert spring and pin into cylinder. B. Turn control key 15 degrees engaging the single leg with the drive cam B. Place tailpiece into cap. clockwise until key stops. in the spindle. C. Thread cap onto the cylinder. C. Pull key to remove IC core. B. Insert spindle cap into the lever, notched NOTE: The cap must be properly adjusted. If end first. too loose, excessive plug end play will prevent C. Push lever in until locking button the key from being withdrawn. If too tight, the engages hole in lever. plug will drag and be difficult to rotate with the D. With control key in core rotate key 15° key. clockwise and insert fully into lever. Turn the key counter-clockwise and remove key. E. Check function before CYLINDER closing door. LOCKING SPRING BUTTON PIN TAILPIECE 12. REMOVING IC LEVERS CAP TAILPIECE A. With IC core removed, depress locking button ASSEMBLY and pull lever to remove. SPINDLE CAP

2 8.500

FRONT

11.000 4.250

FRONT

3.670

BEGINNING SHEET FOLDED SHEET

Additional Notes: Revision History Revision Description: d > Revised artwork 1. None A B C D E F 4600-304 0790 6683 Material Edited By Approved By EC Number Release Date White Paper J. Ellis M. Roberts xxxxx 10/14 Notes Title 1. printed two sides F-Series Keyed Locks 2. printed black 3. tolerance ± .13 Creation Date Number Revision 4. printed in country may vary 10-22-14 030690-000-70 d 5. drawings not to scale 6. Barcode shows after folding Created By Activity J. Ellis 3899 Hancock Expwy Software: InDesign CS6 Security, CO 80911 © Allegion 2014