Troubleshooting AV SYSTEM • If your house has a heavy metal construction • If you cannot control the source from or is equipped with a PC network, it can your second TV when using a remote control, 27992R disturb the signal. Even moving reposition the IR Eye on the video source. the units a few inches can improve the If you are having difficulty locating the IR performance. If this doesn’t work try to sensor window use the remote control to USERPhilex Customer Careline GUIDE 08457 573479 move the and RECEIVER to help locate it. On some AV equipment the another place in the house. If you experience sensor will flash when the remote control is Introduction problems, try placing the units away from in use. Alternatively if the remote is electrical appliances. positioned touching the fascia and the Congratulations on your purchase of the Philex room. In the unlikely case of interference from remote is switched on and off repeatedly AV Wireless AV System. This product has been another wireless AV system nearby, you can • If you are still experiencing interference you while it is being moved across the fascia it is designed to allow an audio/video signal from choose between four alternative operating can try changing the wireless channel. usually possible to narrow down the position equipment such as DVD players, Digital TV frequencies. The channel switches are located in the base of the sensor window. receivers, Satellite Receivers and VCRs to be both of the transmitter and receiver. These both watched and controlled in a different room with- Before attempting to install the system, please out the need for runs of cable or DIY! read through the instructions carefully ensuring have 4 settings 1-4, you can try all 4 settings • If your S-VHS video shows no colour pictures but always make sure that both transmitter you understand the procedure and have all items (only black and white), select CVBS video The receiver can work within 30 metres of the necessary. and receiver are set to the same number output format for your S-VHS VCR. transmitter depending on the building structure setting. and has a built-in remote control sender allowing • If your AV source gives no pictures on either you to control your equipment from a different • If the picture on your second TV is not main or second TV, select CVBS video output correct, select “EXT” or “AV” on second TV, format for your DVD player (check the DVD and make sure that the video source is player’s user manual). Parts supplied with the sender system switched on.

•  If the picture on your second TV is not correct or there is no signal check the Receiver Transmitter channel switches located in the base of the transmitter and receiver. These both have 4 settings 1 - 4, make sure that both are set to the same number setting. The transmiiter and receiver can be identified by the label on the For further information or any queries please contact our rear panel Customer Careline: 0901 293 0038 Calls are charged at £1 per minute from a BT landline. Call charges from other networks may vary Technical Support: http://technical.philex.com

Waste electrical products should not be disposed of with household waste. Please 0413 recycle where facilities exist. Check with Declaration of Conformity available at: your Local Authority for recycling advice. http://technical.philex.com © Philex Electronic Ltd. 2010. V1.2 MK42 0NX www.philex.com

page 4 page 1 Getting the best reception Fig. 2 -Transmitter Connections Main Room MAIN TV • Both the AV transmitter and receiver units • Ensure that both transmitter and receiver are should be placed on flat, stable surfaces. stood upright. Sound/picture quality may be improved slightly by adjusting the direction of • Minimise the number of obstacles between the the units. AV transmitter and receiver. Setting up your Transmitter and Receiver TRANSMITTER SCART INPUT UNIT THE WIRELESS AV SENDER IS FITTED WITH 8) Position one of the infra red eyes on the infra INTEGRATED CONNECTORS FOR YOUR red extender lead in front of the infra red sensor CONVENIENCE. window of your AV source equipment (satellite MAINS receiver or VCR or DVD). The infra red sensor PSU IR CONNECTING THE RECEIVER window on some satellite receivers is marked by To AV Source (Kitchen / Bedroom etc) this symbol . Make sure the curved surface of SAT, DVD, DVBT etc the infra red eye is facing the sensor window as 1) Plug the integrated SCART cable from the back DC 9V SCART OUTPUT shown in Fig. 3 and (For further tips on locating OFF of the RECEIVER into the SCART input on the ON TRANSMITTER located in the receiving room - eg the infra red sensor window see troubleshooting section). Kitchen or bedroom. (See Fig. 1) Integrated SCART-thru plug 3) Connect one of the power adaptors to the 10) Connect the remaining power adaptor to the 9v DC input at the rear of the RECEIVER as shown 9v DC input at the rear of the Transmitter as in Fig. 1. Plug the power adaptor into a mains shown in Fig. 2. Plug the power adaptor into a socket and turn on the power switch on the mains socket and turn on the power switch on Receiver and mains socket. the Transmitter. CONNECTING THE TRANSMITTER 10) On the base of both the transmitter and reeiver (Main viewing room, eg Lounge) is a channel selector. Ensure that the same channel is set to ON on both the transmitter and 5)  Plug the integrated SCART THRU cable from the reveiver. back of the TRANSMITTER to the SCART output Existing SCART Connection socket on your AV source equipment (satellite 11) Select an appropriate AV channel on the receiver or VCR or DVD). receiving TV. The TV should now show whatever Fig. 3 -Positioning the Infra Red Eye 6)  Connect a SCART cable (not supplied) from the signal the transmitter is sending and if the infra SCART-THRU cable to the SCART input on your red eye is properly positioned you will be able television . (See Fig. 2) to control the AV source by pointing the correct remote control at the AV receiver. 7) Plug the Infra Red extender cable into the infra red socket on the Transmitter as shown in Fig. 2. RECEIVER SECOND TV UNIT Fig. 1 - Receiver Connections Room 2

1 2 3 4

MAINS PSU SCART INPUT

A/V OUT Make sure the curved surface of the infra red eye is facing the sensor window

DC 8V

SCART OUTPUT Cable

page 2 page 3