DOCSLIB.ORG

2,205Lbs of Downforce and GT3 Race Suspension Confirmed for Track-Only Mclaren Senna GTR As Dynamic Testing Begins

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
2,205Lbs of Downforce and GT3 Race Suspension Confirmed for Track-Only Mclaren Senna GTR As Dynamic Testing Begins MEDIA Media Information 9:00am ET, November 02, 2018 — 2,205lbs of downforce and GT3 race suspension confirmed for track-only McLaren Senna GTR as dynamic testing begins ▪ McLaren Senna GTR moves closer to production with confirmation of technical specification ▪ 2,205lbs (1,000kg) of downforce; 814bhp (825PS) and 590lb ft torque (800Nm) from twin- turbocharged, 4.0-liter V8 engine ▪ Suspension derived from McLaren GT3 race program and Pirelli slick race tires confirm GTR’s track- only status ▪ Dynamic prototypes begin running this month as development program accelerates ▪ Production capped at 75 examples, each priced at circa $1.4 million plus taxes and all sold The McLaren Senna GTR, a track-only hypercar that debuted in concept form at the Geneva International Motor Show in March 2018 and sold-out in the same month, begins dynamic testing this month with highlights of its technical specification newly confirmed – not least that it will generate 2,205lbs of downforce and have race-bred suspension developed from the system used in McLaren’s GT3 program. The Senna GTR is an even more extreme version of the road-legal McLaren Senna currently being built at the McLaren Production Centre in Woking, Surrey, UK. McLaren tested demand for the track-only, left- hand-drive only car on its introduction at Geneva, saying that up to 75 would be produced. Many more expressions of interest were received, but the company has confirmed that only 75 will be available, all of which are already allocated. Deliveries are expected to begin from September 2019 when production of the road-legal McLaren Senna is complete. The development prototypes that begin this month will initially use modified Senna road car bodywork. The final Senna GTR shape – shown in simple form in a new design sketch – will be based around a chassis with wider track front and rear and center-lock wheels. The carbon fiber body has new, wider fenders, a larger front splitter and rear diffuser and repositioned active rear wing; these last two elements combining to improve aero-efficiency by ‘coupling’ the wing to the airflow from the diffuser, enabling greater – and more accessible – downforce at lower speeds. Optimized aerodynamic performance in yaw improves cornering stability, while reduction in pitch sensitivity leads to even greater braking stability. The lightweight but incredibly strong carbon fiber McLaren Monocage at the heart of each McLaren Senna GTR epitomizes McLaren’s approach to weight reduction, a philosophy which is taken even further with the new GTR. A pared-back interior sees all airbags removed, as well as the infotainment central screen and folding driver display found in the road car, while a new, race-style steering wheel with integrated gearshift MEDIA controls replaces the road-legal component. Air-conditioning is an exception to the rule of absolute minimalism – remaining standard-fit – and a radar-assisted, rear collision avoidance system is also standard. A final vehicle weight is still to be declared, but the GTR will weigh less than the road-going Senna. In combination with the 814bhp output of the 4.0-liter twin-turbocharged V8 engine – an increase of 25bhp over the road-legal Senna – this will see the power-to-weight ratio comfortably exceed that of the road car. Together with torque of up to 590lb ft torque, the result will be astonishing levels of response and performance. The Senna GTR retains the active aerodynamics of the road-legal car – an advantage that would not be permissible in a homologated race car – which is a major enabler in generating the 2,205lbs of downforce. The car has conventional double wishbone suspension, with the geometry, springs, dampers and anti-roll bars having been developed from the system engineered for McLaren’s GT3 customer racing program. Pirelli slick race tires maximize dynamic performance and the braking system – introduced in the Senna road car and also race-derived – is projected to deliver 20% greater maximum deceleration, with resulting forces in excess of 3g. Information about the McLaren Senna GTR and other McLaren cars can be found via:https://latest.mclaren.com/posts/mclaren-senna-gtr-the-ultimate-track-only-hypercar Ends Notes to Editors: A selection of high resolution images accompanying this release is available to download from the McLaren Automotive media site – cars.mclaren.press About McLaren Automotive: McLaren Automotive is a creator of luxury, high-performance sportscars and supercars. Every vehicle is hand-assembled at the McLaren Production Centre (MPC) in Woking, Surrey, England. Launched in 2010, the company is now the largest part of the McLaren Group. The company has three defined product families: Sports Series, Super Series and Ultimate Series which are retailed through over 80 retailers in 30 markets around the world. McLaren is a pioneer that continuously pushes the boundaries. In 1981, it introduced lightweight and strong carbon fibre chassis into Formula 1 with the McLaren MP4/1. Then in 1993 it designed and built the McLaren F1 road car - the company has not built a car without a carbon fibre chassis since. As part of the Ultimate Series, McLaren was the first to deliver a hybrid hypercar, the McLaren P1™. Announced at Goodwood Festival of Speed in 2018, the company’s Track25 business plan will see it invest £1.2billion in research and development to deliver 18 new cars or derivatives by the end of 2025. 2017 saw the company launch further models including the second-generation Super Series, the 570S Spider and the McLaren Senna. In 2018, the company launched the 600LT and the McLaren Speedtail, the next Ultimate Series and McLaren’s first ever Hyper-GT of which only 106 will be produced. MEDIA To support the development, engineering and manufacture of its range of innovative sportscars and supercars, McLaren Automotive partners with world leading companies to provide specialist expertise and technology. These include AkzoNobel, Kenwood, Pirelli and Richard Mille. McLaren Group: The McLaren Group is a global leader in luxury automotive andtechnology and comprises three businesses: Automotive, Racing and Applied Technologies. Further information: Roger Ormisher Vice President, Communications & PR | McLaren North America Phone: +1 714 501 8137 Email: [email protected] Laura Tilley Public Relations | McLaren North America Phone: +1 765 517 2186 Email: [email protected] Media website: cars.mclaren.press Facebook: www.facebook.com/mclarenautomotive Twitter: www.twitter.com/McLarenAuto You Tube: www.youtube.com/mclarenautomotivetv .
Load more

Recommended publications
  • Complete Design and Optimization of the Aerodynamics of a FSAE Car Using Solid Works ANSYS & XFLR5
    Proceedings of the World Congress on Engineering 2016 Vol II WCE 2016, June 29 - July 1, 2016, London, U.K. Complete Design and Optimization of the Aerodynamics of a FSAE Car using Solid works ANSYS & XFLR5 Aravind Prasanth, Sadjyot Biswal, Aman Gupta, Azan Barodawala Member, IAENG Abstract: This paper will give an insight in to how an II. AERODYNAMICS Aerodynamics package of a FSAE car is developed as well as The most important factor in achieving better top speed is the various stages of optimizing and designing the Front wing and Rear wing. The under tray will be explained in a the traction due to the tires and this depends upon the companion paper. The paper will focus on the reasons to use normal force. It can be achieved by increasing the mass, aerodynamic devices, choice of the appropriate wing profile, its however, this takes a toll on the acceleration. Therefore, the 2D and 3D configuration and investigation of the effect of option available is to increase the downforce. The drawback ground proximity for the front wing. Finally, various softwares of adding aerodynamics package will result in the addition are implemented to identify the correct configurations for the of drag. Front and Rear wing. It is important to determine how much top speed can be sacrificed without compensating on the track performance. Index Terms— ANSYS, CFD, downforce, FSAE, XFLR5 A. Sacrificial top speed The acceleration of the car can be expressed as. I. INTRODUCTION he aim is to create a high downforce aerodynamics T package for the FSAE (Formula Society of Automotive (1) Engineers) race car.
    [Show full text]
  • Press Release
    PRESS RELEASE www.youtube.com/fordofeurope www.twitter.com/FordEu www.youtube.com/fordo feurope Ford Mustang Mach 1 touches down in Europe • Track-focused Mustang Mach 1 introduces enhanced powertrain and aerodynamic features for the most agile and responsive Mustang driving experience in Europe ever • V8 power boosted to 460 PS for 0-100 km/h in 4.4 seconds. TREMEC manual and 10- speed auto transmissions feature limited-slip differential. Downforce increased 22 per cent • Sophisticated technologies for track driving fun include MagneRide® adaptive suspension, selectable Drive Modes including Track mode, and Track Apps including Launch Control COLOGNE, Germany, May 18, 2021 – First deliveries of the new Ford Mustang Mach 1 – the most track-focused Mustang ever offered to customers in Europe – are now underway, Ford today announced. Enhancing the powerful performance of the world’s best-selling sports car with a specially- calibrated 460 PS 5.0-litre V8 engine 1 and unique transmission specifications, Mustang Mach 1 also introduces bespoke aerodynamics and new performance component cooling systems for greater agility and consistent on-track performance. Mustang Mach 1 delivers 0-100 km/h acceleration in 4.4 seconds and increases downforce by 22 per cent compared with Mustang GT for enhanced cornering capability and high-speed stability. Introducing the iconic Mach 1 moniker to the region for the first time, the limited-edition model also delivers race-derived styling, specification and detailing for performance car fans. “There’s a reason Mustang is the world’s best-selling sports car, but the Mach 1 is going to elevate Mustang to another level in the hearts of performance car fans on this side of the Atlantic,” said Matthias Tonn, Mustang Mach 1 chief programme engineer for Europe.
    [Show full text]
  • Passionate Mustang Team Works After-Hours to Create New Performance Pack for Ultimate Road- Hugging Thrill Ride
    FORD MEDIA CENTER Passionate Mustang Team Works After-Hours to Create New Performance Pack for Ultimate Road- Hugging Thrill Ride • New Mustang GT Performance Pack Level 2 raises Mustang GT’s game and bridges the gap between GT Performance Pack and GT350 • Performance Pack Level 2 is accentuated by a lower, more aggressive stance, aerodynamically balanced high-performance front splitter and rear spoiler – all designed to add more downforce to attack curves for an exhilarating feel behind the wheel • Michelin Pilot Sport Cup 2 tires, retuned steering and MagneRide® suspension deliver ultra- responsive road-gripping capabilities in new manual transmission-equipped Mustang GT with Performance Pack Level 2 DEARBORN, Mich., Oct. 23, 2017 – Evenings in the garage. Weekends at the track. Gearheads everywhere can appreciate the extra time and effort the Mustang team took to quickly prototype and hone the Performance Pack Level 2 for the new 2018 Ford Mustang GT. “A passion to create something special is what really drove this project,” said Tom Barnes, Mustang vehicle engineering manager. “And that really showed in the off-the-clock way we went about doing our work.” Longtime tire and wheel engineer Chauncy Eggleston led development of unique 19-inch wheels that help provide notable steering and handling response improvements. Mustang veteran Jonathan Gesek, former aerodynamics specialist at NASA and now with Ford’s aerodynamics group, spearheaded development of a high-performance front splitter and rear spoiler. And Jamie Cullen, Ford supervisor for vehicle dynamics development, led road test efforts to ensure the car delivers ultra-responsive steering, braking and handling performance.
    [Show full text]
  • Understeer / Oversteer “Handling Issues” Are Caused by the Driver, Not the Car
    Trackside Classroom Understeer and Oversteer VGC i Venture Consulting Group, Inc Disclaimer The techniques shown here have been compiled from experienced sources believed to be reliable and to represent the best current opinions on driving on track. But they are advisory only. Driving at speed at NJMP Lightning, or any other track, requires skill, judgment and experience. These techniques assume the reader has high performance driving knowledge and applies them as applicable to their level of drivingVGC experience.i Venture Consulting Group, Inc High-performance driving can be very dangerous, carries inherent risks and may result in injury or death. NNJR and PCA make no warranty, guarantee or representations as to the absolute correctness or sufficiency of any representation contained herein. Nor can it be assumed that all acceptable safety measures are contained herein or that other or additional measures may not be required under particular or exceptional conditions or circumstances. Understeer/Oversteer Agenda • Definitions • How to know / learn? • Causes – Setup – Driver • How to “fix” Trackside Classroom Copyright NNJR 2019 Slide 3 How to know/learn? • Do you know if your car is understeering? – Oversteering? – Both (at different times)? • Sensory input sessions – Sound – “Seat of the pants” (Kinesthetics) – Feel in the steering wheel – Vision: car’s path vs. intended path Trackside Classroom Copyright NNJR 2019 Slide 4 Understeer: the car won’t turn! Trackside Classroom Copyright NNJR 2019 Slide 5 Understeer • Front tires have less
    [Show full text]
  • Research Article Advanced Modeling and Simulation of Vehicle Active Aerodynamic Safety
    Hindawi Journal of Advanced Transportation Volume 2019, Article ID 7308590, 17 pages https://doi.org/10.1155/2019/7308590 Research Article Advanced Modeling and Simulation of Vehicle Active Aerodynamic Safety Krzysztof Kurec ,1 MichaB Remer ,1 Jakub Broniszewski ,1 PrzemysBaw Bibik ,1 Sylwester Tudruj,2 and Janusz Piechna 1 1 Warsaw University of Technology, Institute of Aeronautics and Applied Mechanics, Warsaw 00-665, Poland 2Warsaw University of Technology, Institute of Micromechanics and Photonics, Warsaw 02-525, Poland Correspondence should be addressed to Janusz Piechna; [email protected] Received 3 August 2018; Accepted 6 January 2019; Published 3 February 2019 Guest Editor: Mihai Dimian Copyright © 2019 Krzysztof Kurec et al. Tis is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited. Te aim of this study was to extend the safety limits of fast moving cars by the application, in a controlled way, of aerodynamic forces which increase as the square of a car’s velocity and, if lef uncontrolled, dramatically reduce car safety. Tis paper presents the methods, assumptions, and results of numerical and experimental investigations by modeling and simulation of the aerodynamic characteristics and dynamics of a small sports car equipped with movable aerodynamic elements operated by an electronic subsystem for data acquisition and aerodynamics active automatic control. 1. Introduction such action has drawbacks in the form of car bodies gener- ating aerodynamic lif forces at high speed, together with a Currently, the trend to minimize emissions by limiting decrease in a car’s directional stability and reduction of safety fossil fuel consumption leads to lighter cars with a low limits during fast cornering.
    [Show full text]
  • Tuning Section
    TUNING SECTION It’s like Ripley’s Believe It Or Not – Take it for what it’s worth! TRANSMISSION HEIGHT The X – 6 is the first mass produced off-road buggy we know of with adjustable transmission height. This allows you to adjust the height of the point of contact between the dogbones and the outdrives. In theory, raising this point of contact gives more forward bite and less side bite. Lowering the point of contact does the opposite: more side bite and less forward. We are changing the angle of the dogbone in the outdrive. If you keep the ride height the same, changing the height of the outdrives changes the angle of the dogbones. On a conventional buggy, rear ride height changes are done to affect dogbone angle, and front ride height is adjusted secondly to compensate for the rear. The New Math allows you to set dogbone angle and ride height independently. The Team usually sets transmission height first, then adjusts the remainder of the car, with front and rear ride heights based on the remainder of the set-up rather than dogbone angle considerations. Included in Bag E is a Ziplock bag of transmission shims; four each of .030”, .060”, .090”. and .120” Counting zero, this gives five transmission height positions. .060” is about the same as your B4. Unfortunately, we have yet to figure out an economical way to change transmission height without moving the motor in tandem. Therefore, changing transmission height also changes the car’s C.O.G. slightly, which affects handling. As with any other car, by the time qualifying starts it’s the whole package that counts.
    [Show full text]
  • Wednesday, May 8, 2019
    Wednesday, May 8, 2019 AVL 9:45 – 11:15 a.m. Suite 216 Performance Trade off Analysis What if decisions for your next car will be made on objective numbers rather than subjective feedback from previous team members? Using simulation tools early in the development process can help to speed up the development significantly. Not only that, if done in a structured way it can help vehicle performance on track and justify your design decisions. AVL will present a process on how to focus the development of your car on the “right” technical measures using a virtual environment. Presenter: Thomas Mueller-Werth, Group Leader - Vehicle Engineering ZF 9:45 – 11:15 a.m. Suite 218 0 to 60: From Formula SAE to Career - A dynamic panel of professionals discuss their career paths and experiences Only one year ago Justin Rujan and Filipp Balayev were where you are today – tirelessly building and perfecting their cars as part of University of Michigan – Dearborn’s Formula SAE team. Justin and Filipp learned valuable technical and leadership skills as they helped build, compete and manage multiple top 10 cars. They carried these engineering skills and experiences past graduation and into their careers. Today, they are both calibration engineers within ZF’s powertrain group. Eric Shelleman earned his degree from Clemson University and honed his skills in the university machine shop. Now as a part of the ZF Race Engineering group, Eric develops, produces and distributes ZF core products in the field of driveline and chassis technology for race car applications to various motorsport series around the world.
    [Show full text]
  • Aerodynamics of Race Cars
    AR266-FL38-02 ARI 22 November 2005 19:22 Aerodynamics of Race Cars Joseph Katz Department of Aerospace Engineering, San Diego State University, San Diego, California 92182; email: [email protected] Annu. Rev. Fluid Mech. Key Words 2006. 38:27–63 downforce, inverted wings, ground effect, drag The Annual Review of Fluid Mechanics is online at fluid.annualreviews.org Abstract doi: 10.1146/annurev.fluid. Race car performance depends on elements such as the engine, tires, suspension, 38.050304.092016 road, aerodynamics, and of course the driver. In recent years, however, vehicle aero- Copyright c 2006 by dynamics gained increased attention, mainly due to the utilization of the negative Annual Reviews. All rights lift (downforce) principle, yielding several important performance improvements. reserved This review briefly explains the significance of the aerodynamic downforce and how 0066-4189/06/0115- it improves race car performance. After this short introduction various methods to 0027$20.00 generate downforce such as inverted wings, diffusers, and vortex generators are dis- Annu. Rev. Fluid Mech. 2006.38:27-63. Downloaded from www.annualreviews.org by Universidade Estadual de Campinas (Unicamp) on 04/17/11. For personal use only. cussed. Due to the complex geometry of these vehicles, the aerodynamic interaction between the various body components is significant, resulting in vortex flows and lifting surface shapes unlike traditional airplane wings. Typical design tools such as wind tunnel testing, computational fluid dynamics, and track testing, and their rel- evance to race car development, are discussed as well. In spite of the tremendous progress of these design tools (due to better instrumentation, communication, and computational power), the fluid dynamic phenomenon is still highly nonlinear, and predicting the effect of a particular modification is not always trouble free.
    [Show full text]
  • Svra Formula Ford Rulebook
    Revised 10/16 SVRA FORMULA FORD RULEBOOK SVRA Formula Ford is comprised of 3 distinct formula ford classes. (Ford engine only) Vintage Ford- First generation 1967-1972. Specific list of eligible chassis. Club Ford- Second generation 1973-1981 with outboard suspension on at least one end. Specific list of eligible chassis. Post Club Ford- 1982-2008, or any pre 2009 chassis with inboard suspension on both ends. Earlier model cars prepared/ modified to later class rules will be classified in the later class. Later model cars cannot be run in an earlier class regardless of preparation level/ modifications. I. Definition A formula for single seat, open wheel racecars campaigned from 1967 through 1972, 1973 through 1981 and 1982 and later, using the standard Ford Motor Company 1600 cross flow pushrod engine. Formula Ford is a restricted class. Therefore, any allowable modifications, changes or additions are as stated herein. There are no exceptions. IF IN DOUBT, DON’T. As additional OEM parts (particularly engine parts) become obsolete there will be a need to update these rules to allow suitable replacement parts. However, no new part, change, or modification is permitted, beyond what is allowed in these rules, until it has been reviewed, approved, and published into these rules. There are no exceptions. IF IN DOUBT, DON’T. GENERAL RULES APPLICABLE TO ALL THREE CLASSES Tires: following is the allowable tires for all classes (Wet or Dry) Front: Hoosier 135/545-13VFF Rear: Hoosier 165/580-13VFF Front: Toyo Proxes R888, 185/60R/13 Rear: Toyo Proxes R888, 205/60R/13 Shaving, or reducing tread depth of tire by any means other than normal on track driving is prohibited.
    [Show full text]
  • Todd Soderquist Chief Program Engineer Ford Performance
    Todd Soderquist Chief Program Engineer Ford Performance 1 FORD PERFORMANCE VISION: Creators of world’s leading performance portfolio… accessible to all. FORD PERFORMANCE MISSION: Fuel innovation and passion for Ford, on and off the road 2 PARTS & ACCESSORIES MOTORSPORTS Motorsports serves as a test-bed for technology and pride point for fans Rapid integration of Expansion of parts, race-proven technology accessories, merchandise to market faster PERFORMANCE PERFORMANCE EXPERIENCES VEHICLES Captures new, younger customers as performance segment grows 3 4 Up to F-SERIES RAPTOR 500 lbs. Lighter than last Generation Fox Racing Shox 6 Terrain Modes Off Road Status 5 FORD GT RACING LEGEND Ford’s 1st LeMans Win 1966, Recreated in 2016 Third Generation of the Ford GT Super Car Returned in 2017 7 The Chassis The Ford GT’s innovations begin with its chassis: •A unique carbon tub architecture •Investment cast front and rear suspension structures •A tubular chromoly upper cockpit structure •A fully integrated IP Chassis – Carbon Tub The carbon tub is of unique design and construction: •Monolithic mouldings are bonded together – analogous to a conventional unibody, but in “black” Chassis – Integrated Cage Tubular high-strength steel (15CDV6 CrMo) forms the upper cockpit structure: •Creating a roll cage that meets both FIA and global road car safety requirements •Only add-on components required for race car version Chassis – Integrated IP Instrument panel (IP) structure is integrated into the main CFRP tub moulding: •HVAC ducting is incorporated into
    [Show full text]
  • Race Car Aerodynamics
    Race Car Aerodynamics KTH – Royal Institute of Technology Stockholm – May 21st, 2010 Corrado CASIRAGHI Tatuus Racing Company Contents LOGO • Historic overview • Race car categories • Aerodynamic and performance • Aerodynamic tools • Validation: CFD, Wind Tunnel, Track Test Race Car Aerodynamics - May 21st, 2010 Company Historic overview LOGO • First steps • Drag reduction: fast circuits, low power engines 1915: Indianapolis 500 1916: Indianapolis 500 Race Car Aerodynamics - May 21st, 2010 Company Historic overview LOGO • Race car evolution • Downforce research: tire and engine technology are improved 1965: Chaparral-2C 1966: Chaparral-2E Race Car Aerodynamics - May 21st, 2010 Company Historic overview LOGO • Race Car Evolution • Extreme solution: adjustable wings, suction fans 1968: Lotus – Type 49 1966: Chaparral-2J (Sucker car) Race Car Aerodynamics - May 21st, 2010 Company Historic overview LOGO • Race Car Evolution • Wing cars: reversed wing underbody and sealing skirts 1977: Lotus type 78 1977: Lotus type 78 Race Car Aerodynamics - May 21st, 2010 Company Historic overview LOGO • Race Car Evolution • Modern era: flat and “stepped” underbody 1983: McLaren MP4-1C 2004: Jordan “stepped” underfloor Race Car Aerodynamics - May 21st, 2010 Company Historic overview LOGO • Sports Car • Apex of efficiency 1999: Mercedes CLR 1999: Toyota GT-One 1999: BMW-LMR 1999: Audi R8R Race Car Aerodynamics - May 21st, 2010 Company Historic overview LOGO • Sports Car • Safety problems 1998: Porsche GT1 1999: Mercedes CLR Race Car Aerodynamics - May 21st, 2010 Company Race car categories LOGO • Sedan-based race cars • WTCC, Rally, Nascar,etc. • Enhancements in stiffness and safety (roll-cage), minimum aerodynamic modifications Race Car Aerodynamics - May 21st, 2010 Company Race car categories LOGO • Enclosed Wheel race cars • LeMans Prototypes LMP1, LMP2..
    [Show full text]
  • Mustang Ecoboost® | Ecoboost Premium | Gt | Gt Premium | Bullitt | Shelby® Gt350® | Shelby Gt500® Built on Pony Power
    2020 MUSTANG ECOBOOST® | ECOBOOST PREMIUM | GT | GT PREMIUM | BULLITT | SHELBY® GT350® | SHELBY GT500® BUILT ON PONY POWER. Open roads. Closed tracks. Long straightaways. This legendary icon thrives on them all. A high-revving celebration of pure American muscle, Ford Mustang is meant to be driven. Hard. Over iconic courses like The Carousel and on any freshly laid strip of blacktop near you. 55 years of legendary Pony cars brings us to the heart-pounding choices below. The most powerful 4-cylinder engine from any domestic automaker debuts in the 2020 Mustang EcoBoost® with the new 2.3L High Performance Package. And with 760 thunderous horsepower,1 the all-new Shelby® GT500® is the most powerful street- legal Mustang. EVER. The hard-charging Mustang GT, limited-edition BULLITT, and GT350® and GT350R round out the lineup. Ford was built on the belief that freedom of movement drives human progress. It’s a conviction that led Henry Ford and “Spider” Huff to achieve a world-speed record in 1904 with the “999.” And nothing signifies this belief better today than Mustang. So buckle up for the ride of your life. 2020 should see progress at breathtaking speed. ECOBOOST | ECOBOOST PREMIUM GT | GT PREMIUM SHELBY GT500 SHELBY GT350 EcoBoost Premium. Magnetic. GT Premium. Iconic Silver. Black Accent Package. Twister Orange. Carbon Fiber Track Pack. Shadow Black. R Package. Available equipment. Available equipment. Available equipment. Available equipment. BULLITT and all related characters and elements ® & ™ Warner Bros Entertainment Inc. (s19) 1Horsepower rating based on premium fuel per SAE J1349® standard. Your results may vary. NEW 2.3L HIGH PERFORMANCE PACKAGE Available on EcoBoost® fastback or convertible, with 6-speed manual or available 10-speed automatic transmission.
    [Show full text]