An Introduction to TCP/IP
Total Page:16
File Type:pdf, Size:1020Kb
Load more
Recommended publications
-
The Internet in Iot—OSI, TCP/IP, Ipv4, Ipv6 and Internet Routing
Chapter 2 The Internet in IoT—OSI, TCP/IP, IPv4, IPv6 and Internet Routing Reliable and efficient communication is considered one of the most complex tasks in large-scale networks. Nearly all data networks in use today are based on the Open Systems Interconnection (OSI) standard. The OSI model was introduced by the International Organization for Standardization (ISO), in 1984, to address this composite problem. ISO is a global federation of national standards organizations representing over 100 countries. The model is intended to describe and standardize the main communication functions of any telecommunication or computing system without regard to their underlying internal structure and technology. Its goal is the interoperability of diverse communication systems with standard protocols. The OSI is a conceptual model of how various components communicate in data-based networks. It uses “divide and conquer” concept to virtually break down network communication responsibilities into smaller functions, called layers, so they are easier to learn and develop. With well-defined standard interfaces between layers, OSI model supports modular engineering and multivendor interoperability. 2.1 The Open Systems Interconnection Model The OSI model consists of seven layers as shown in Fig. 2.1: physical (Layer 1), data link (Layer 2), network (Layer 3), transport (Layer 4), session (Layer 5), presentation (Layer 6), and application (Layer 7). Each layer provides some well-defined services to the adjacent layer further up or down the stack, although the distinction can become a bit less defined in Layers 6 and 7 with some services overlapping the two layers. • OSI Layer 7—Application Layer: Starting from the top, the application layer is an abstraction layer that specifies the shared protocols and interface methods used by hosts in a communications network. -
External Data Representation Standard: Protocol Specification 1. Status of This Standard Note: This Chapter Specifies a Protocol
External Data Representation Standard: Protocol Specification 1. Status of this Standard Note: This chapter specifies a protocol that Sun Microsystems, Inc., and others are using. It has been desig- nated RFC1014 by the ARPA Network Information Center. 2. Introduction XDR is a standard for the description and encoding of data. It is useful for transferring data between differ- ent computer architectures, and has been used to communicate data between such diverse machines as the Sun Workstation, VAX, IBM-PC, and Cray. XDR fits into the ISO presentation layer, and is roughly analo- gous in purpose to X.409, ISO Abstract Syntax Notation. The major difference between these two is that XDR uses implicit typing, while X.409 uses explicit typing. XDR uses a language to describe data formats. The language can only be used only to describe data; it is not a programming language. This language allows one to describe intricate data formats in a concise man- ner. The alternative of using graphical representations (itself an informal language) quickly becomes incomprehensible when faced with complexity. The XDR language itself is similar to the C language [1], just as Courier [4] is similar to Mesa. Protocols such as Sun RPC (Remote Procedure Call) and the NFS (Network File System) use XDR to describe the format of their data. The XDR standard makes the following assumption: that bytes (or octets) are portable, where a byte is defined to be 8 bits of data. A giv enhardware device should encode the bytes onto the various media in such a way that other hardware devices may decode the bytes without loss of meaning. -
OSI Model and Network Protocols
CHAPTER4 FOUR OSI Model and Network Protocols Objectives 1.1 Explain the function of common networking protocols . TCP . FTP . UDP . TCP/IP suite . DHCP . TFTP . DNS . HTTP(S) . ARP . SIP (VoIP) . RTP (VoIP) . SSH . POP3 . NTP . IMAP4 . Telnet . SMTP . SNMP2/3 . ICMP . IGMP . TLS 134 Chapter 4: OSI Model and Network Protocols 4.1 Explain the function of each layer of the OSI model . Layer 1 – physical . Layer 2 – data link . Layer 3 – network . Layer 4 – transport . Layer 5 – session . Layer 6 – presentation . Layer 7 – application What You Need To Know . Identify the seven layers of the OSI model. Identify the function of each layer of the OSI model. Identify the layer at which networking devices function. Identify the function of various networking protocols. Introduction One of the most important networking concepts to understand is the Open Systems Interconnect (OSI) reference model. This conceptual model, created by the International Organization for Standardization (ISO) in 1978 and revised in 1984, describes a network architecture that allows data to be passed between computer systems. This chapter looks at the OSI model and describes how it relates to real-world networking. It also examines how common network devices relate to the OSI model. Even though the OSI model is conceptual, an appreciation of its purpose and function can help you better understand how protocol suites and network architectures work in practical applications. The OSI Seven-Layer Model As shown in Figure 4.1, the OSI reference model is built, bottom to top, in the following order: physical, data link, network, transport, session, presentation, and application. -
OSI Model: the 7 Layers of Network Architecture
OSI Model: The 7 Layers of Network Architecture The Open Systems Interconnection (OSI) Reference Model is a conceptual framework that describes functions of the networking or telecommunication system independently from the underlying technology infrastructure. It divides data communication into seven abstraction layers and standardizes protocols into appropriate groups of networking functionality to ensure interoperability within the communication system regardless of the technology type, vendor, and model. The OSI model was originally developed to facilitate interoperability between vendors and to define clear standards for network communication. However, the olderTCP/IP model remains the ubiquitous reference framework for Internet communications today. The 7 layers of the OSI model This image illustrates the seven layers of the OSI model. Below, we’ll briefly describe each layer, from bottom to top. 1. Physical The lowest layer of the OSI model is concerned with data communication in the form of electrical, optic, or electromagnetic signals physically transmitting information between networking devices and infrastructure. The physical layer is responsible for the communication of unstructured raw data streams over a physical medium. It defines a range of aspects, including: Electrical, mechanical, and physical systems and networking devices that include specifications such as cable size, signal frequency, voltages, etc. Topologies such as Bus, Star, Ring, and Mesh Communication modes such as Simplex, Half Duplex, and Full Duplex Data transmission performance, such as Bit Rate and Bit Synchronization Modulation, switching, and interfacing with the physical transmission medium Common protocols including Wi-Fi, Ethernet, and others Hardware including networking devices, antennas, cables, modem, and intermediate devices such as repeaters and hubs 2. -
Is QUIC a Better Choice Than TCP in the 5G Core Network Service Based Architecture?
DEGREE PROJECT IN INFORMATION AND COMMUNICATION TECHNOLOGY, SECOND CYCLE, 30 CREDITS STOCKHOLM, SWEDEN 2020 Is QUIC a Better Choice than TCP in the 5G Core Network Service Based Architecture? PETHRUS GÄRDBORN KTH ROYAL INSTITUTE OF TECHNOLOGY SCHOOL OF ELECTRICAL ENGINEERING AND COMPUTER SCIENCE Is QUIC a Better Choice than TCP in the 5G Core Network Service Based Architecture? PETHRUS GÄRDBORN Master in Communication Systems Date: November 22, 2020 Supervisor at KTH: Marco Chiesa Supervisor at Ericsson: Zaheduzzaman Sarker Examiner: Peter Sjödin School of Electrical Engineering and Computer Science Host company: Ericsson AB Swedish title: Är QUIC ett bättre val än TCP i 5G Core Network Service Based Architecture? iii Abstract The development of the 5G Cellular Network required a new 5G Core Network and has put higher requirements on its protocol stack. For decades, TCP has been the transport protocol of choice on the Internet. In recent years, major Internet players such as Google, Facebook and CloudFlare have opted to use the new QUIC transport protocol. The design assumptions of the Internet (best-effort delivery) differs from those of the Core Network. The aim of this study is to investigate whether QUIC’s benefits on the Internet will translate to the 5G Core Network Service Based Architecture. A testbed was set up to emulate traffic patterns between Network Functions. The results show that QUIC reduces average request latency to half of that of TCP, for a majority of cases, and doubles the throughput even under optimal network conditions with no packet loss and low (20 ms) RTT. Additionally, by measuring request start and end times “on the wire”, without taking into account QUIC’s shorter connection establishment, we believe the results indicate QUIC’s suitability also under the long-lived (standing) connection model. -
Lecture: TCP/IP 2
TCP/IP- Lecture 2 [email protected] How TCP/IP Works • The four-layer model is a common model for describing TCP/IP networking, but it isn’t the only model. • The ARPAnet model, for instance, as described in RFC 871, describes three layers: the Network Interface layer, the Host-to- Host layer, and the Process-Level/Applications layer. • Other descriptions of TCP/IP call for a five-layer model, with Physical and Data Link layers in place of the Network Access layer (to match OSI). Still other models might exclude either the Network Access or the Application layer, which are less uniform and harder to define than the intermediate layers. • The names of the layers also vary. The ARPAnet layer names still appear in some discussions of TCP/IP, and the Internet layer is sometimes called the Internetwork layer or the Network layer. [email protected] 2 [email protected] 3 TCP/IP Model • Network Access layer: Provides an interface with the physical network. Formats the data for the transmission medium and addresses data for the subnet based on physical hardware addresses. Provides error control for data delivered on the physical network. • Internet layer: Provides logical, hardware-independent addressing so that data can pass among subnets with different physical architectures. Provides routing to reduce traffic and support delivery across the internetwork. (The term internetwork refers to an interconnected, greater network of local area networks (LANs), such as what you find in a large company or on the Internet.) Relates physical addresses (used at the Network Access layer) to logical addresses. -
Internet Protocol Suite
InternetInternet ProtocolProtocol SuiteSuite Srinidhi Varadarajan InternetInternet ProtocolProtocol Suite:Suite: TransportTransport • TCP: Transmission Control Protocol • Byte stream transfer • Reliable, connection-oriented service • Point-to-point (one-to-one) service only • UDP: User Datagram Protocol • Unreliable (“best effort”) datagram service • Point-to-point, multicast (one-to-many), and • broadcast (one-to-all) InternetInternet ProtocolProtocol Suite:Suite: NetworkNetwork z IP: Internet Protocol – Unreliable service – Performs routing – Supported by routing protocols, • e.g. RIP, IS-IS, • OSPF, IGP, and BGP z ICMP: Internet Control Message Protocol – Used by IP (primarily) to exchange error and control messages with other nodes z IGMP: Internet Group Management Protocol – Used for controlling multicast (one-to-many transmission) for UDP datagrams InternetInternet ProtocolProtocol Suite:Suite: DataData LinkLink z ARP: Address Resolution Protocol – Translates from an IP (network) address to a network interface (hardware) address, e.g. IP address-to-Ethernet address or IP address-to- FDDI address z RARP: Reverse Address Resolution Protocol – Translates from a network interface (hardware) address to an IP (network) address AddressAddress ResolutionResolution ProtocolProtocol (ARP)(ARP) ARP Query What is the Ethernet Address of 130.245.20.2 Ethernet ARP Response IP Source 0A:03:23:65:09:FB IP Destination IP: 130.245.20.1 IP: 130.245.20.2 Ethernet: 0A:03:21:60:09:FA Ethernet: 0A:03:23:65:09:FB z Maps IP addresses to Ethernet Addresses -
The Internet Protocol, Version 4 (Ipv4)
Today’s Lecture I. IPv4 Overview The Internet Protocol, II. IP Fragmentation and Reassembly Version 4 (IPv4) III. IP and Routing IV. IPv4 Options Internet Protocols CSC / ECE 573 Fall, 2005 N.C. State University copyright 2005 Douglas S. Reeves 1 copyright 2005 Douglas S. Reeves 2 Internet Protocol v4 (RFC791) Functions • A universal intermediate layer • Routing IPv4 Overview • Fragmentation and reassembly copyright 2005 Douglas S. Reeves 3 copyright 2005 Douglas S. Reeves 4 “IP over Everything, Everything Over IP” IP = Basic Delivery Service • Everything over IP • IP over everything • Connectionless delivery simplifies router design – TCP, UDP – Dialup and operation – Appletalk – ISDN – Netbios • Unreliable, best-effort delivery. Packets may be… – SCSI – X.25 – ATM – Ethernet – lost (discarded) – X.25 – Wi-Fi – duplicated – SNA – FDDI – reordered – Sonet – ATM – Fibre Channel – Sonet – and/or corrupted – Frame Relay… – … – Remote Direct Memory Access – Ethernet • Even IP over IP! copyright 2005 Douglas S. Reeves 5 copyright 2005 Douglas S. Reeves 6 1 IPv4 Datagram Format IPv4 Header Contents 0 4 8 16 31 •Version (4 bits) header type of service • Functions version total length (in bytes) length (x4) prec | D T R C 0 •Header Length x4 (4) flags identification fragment offset (x8) 1. universal 0 DF MF s •Type of Service (8) e time-to-live (next) protocol t intermediate layer header checksum y b (hop count) identifier •Total Length (16) 0 2 2. routing source IP address •Identification (16) 3. fragmentation and destination IP address reassembly •Flags (3) s •Fragment Offset ×8 (13) e t 4. Options y IP options (if any) b •Time-to-Live (8) 0 4 ≤ •Protocol Identifier (8) s e t •Header Checksum (16) y b payload 5 •Source IP Address (32) 1 5 5 6 •Destination IP Address (32) ≤ •IP Options (≤ 320) copyright 2005 Douglas S. -
The OSI Model: Understanding the Seven Layers of Computer Networks
Expert Reference Series of White Papers The OSI Model: Understanding the Seven Layers of Computer Networks 1-800-COURSES www.globalknowledge.com The OSI Model: Understanding the Seven Layers of Computer Networks Paul Simoneau, Global Knowledge Course Director, Network+, CCNA, CTP Introduction The Open Systems Interconnection (OSI) model is a reference tool for understanding data communications between any two networked systems. It divides the communications processes into seven layers. Each layer both performs specific functions to support the layers above it and offers services to the layers below it. The three lowest layers focus on passing traffic through the network to an end system. The top four layers come into play in the end system to complete the process. This white paper will provide you with an understanding of each of the seven layers, including their functions and their relationships to each other. This will provide you with an overview of the network process, which can then act as a framework for understanding the details of computer networking. Since the discussion of networking often includes talk of “extra layers”, this paper will address these unofficial layers as well. Finally, this paper will draw comparisons between the theoretical OSI model and the functional TCP/IP model. Although TCP/IP has been used for network communications before the adoption of the OSI model, it supports the same functions and features in a differently layered arrangement. An Overview of the OSI Model Copyright ©2006 Global Knowledge Training LLC. All rights reserved. Page 2 A networking model offers a generic means to separate computer networking functions into multiple layers. -
61A Lecture 35 Distributed Computing Internet Protocol Transmission
Announcements • Homework 9 (6 pts) due Wednesday 11/26 @ 11:59pm ! Homework Party Monday 6pm-8pm in 2050 VLSB • Guest in live lecture, TA Soumya Basu, on Monday 11/24 • Optional Scheme recursive art contest due Monday 12/1 @ 11:59pm 61A Lecture 35 • No lecture on Wednesday 11/26 (turkey) • No lab on Tuesday 11/25 & Wednesday 11/26 • The week of 12/1: Homework 10 due Wednesday 12/3 & Quiz 3 due Thursday 12/4 on SQL Monday, November 24 ! The lab on SQL (12/2 & 12/3) will be an excellent place to get homework help 2 Distributed Computing A distributed computing application consists of multiple programs running on multiple computers that together coordinate to perform some task. • Computation is performed in parallel by many computers. • Information can be restricted to certain computers. • Redundancy and geographic diversity improve reliability. Distributed Computing Characteristics of distributed computing: • Computers are independent — they do not share memory. • Coordination is enabled by messages passed across a network. • Individual programs have differentiating roles. Distributed computing for large-scale data processing: • Databases respond to queries over a network. • Data sets can be partitioned across multiple machines (next lecture). 4 Network Messages Computers communicate via messages: sequences of bytes transmitted over a network. Messages can serve many purposes: • Send data to another computer • Request data from another computer • Instruct a program to call a function on some arguments. Internet Protocol • Transfer a program to be executed by another computer. Messages conform to a message protocol adopted by both the sender (to encode the message) & receiver (to interpret the message). -
Lesson-13: INTERNET ENABLED SYSTEMS NETWORK PROTOCOLS
DEVICES AND COMMUNICATION BUSES FOR DEVICES NETWORK– Lesson-13: INTERNET ENABLED SYSTEMS NETWORK PROTOCOLS Chapter-5 L13: "Embedded Systems - Architecture, Programming and Design", 2015 1 Raj Kamal, Publs.: McGraw-Hill Education Internet enabled embedded system Communication to other system on the Internet. Use html (hyper text markup language) or MIME (Multipurpose Internet Mail Extension) type files Use TCP (transport control protocol) or UDP (user datagram protocol) as transport layer protocol Chapter-5 L13: "Embedded Systems - Architecture, Programming and Design", 2015 2 Raj Kamal, Publs.: McGraw-Hill Education Internet enabled embedded system Addressed by an IP address Use IP (internet protocol) at network layer protocol Chapter-5 L13: "Embedded Systems - Architecture, Programming and Design", 2015 3 Raj Kamal, Publs.: McGraw-Hill Education MIME Format to enable attachment of multiple types of files txt (text file) doc (MSOFFICE Word document file) gif (graphic image format file) jpg (jpg format image file) wav format voice or music file Chapter-5 L13: "Embedded Systems - Architecture, Programming and Design", 2015 4 Raj Kamal, Publs.: McGraw-Hill Education A system at one IP address Communication with other system at another IP address using the physical connections on the Internet and routers Since Internet is global network, the system connects to remotely as well as short range located system. Chapter-5 L13: "Embedded Systems - Architecture, Programming and Design", 2015 5 Raj Kamal, Publs.: McGraw-Hill Education -
Osi (Open Systems Interconnection) Model
OSI (OPEN SYSTEMS INTERCONNECTION) MODEL OSI (Open Systems Interconnection) is a standard description or "reference model" for how messages should be transmitted UNDERSTANDING EACH LAYER between any two points in a network. Layer 7 – Application layer There are 7 layers in this model: This is the closest layer to the end user. It provides the interface between the applications we use and the underlying layers. But 7 APPLICATION notice that the programs you are using (like a web browser – Firefox…) do not belong to Application layer. Telnet, FTP, email client (SMTP), Hyper Text Transfer Protocol (HTTP) are examples of 6 PRESENTATION Application layer. 5 SESSION Layer 6 – Presentation layer This layer ensures the presentation of data, that the communica- tions passing through are in the appropriate form for the recipient. 4 TRANSPORT In general, it acts as a translator of the network. For example, you want to send an email and the Presentation will format your data 3 NETWORK into email format. Or you want to send photos to your friend, the Presentation layer will format your data into GIF, JPG or PNG… 2 DATA LINK format. Layer 5 – Session layer 1 PHYSICAL Layer 5 establishes, maintains and ends communication with the receiving device. THE PROCESS Layer 4 – Transport layer This layer maintains ow control of data and provides for error checking and recovery of data between the devices. The most When a device wants to send information to another one, its data common example of Transport layer is Transmission Control Proto- must go from top to bottom layer. But when a device receives this col (TCP) and User Datagram Protocol (UDP).