SHARPENING YOUR DRILL BITS a Few Months Ago We Discussed Using a Good Cutting Fluid When Drill Or Taping Operations on Your Project

Total Page：16

File Type：pdf, Size：1020Kb

SHARPENING YOUR DRILL BITS a Few Months Ago We Discussed Using a Good Cutting Fluid When Drill Or Taping Operations on Your Project

Tool Review – Loren Sievila SHARPENING YOUR DRILL BITS A few months ago we discussed using a good cutting fluid when drill or taping operations on your project. Even if you always use cutting fluid, your drill bits will get dull and it will take more effort to drill a hole. You can always go out and buy new bits as the smaller one we often use aren't that expensive, usually less than $2.00 a piece. But if you have to get a new 1/4" x 12 " aircraft extension bit it will set you back $10.00 to $15.00 a piece. Investing in a drill bit sharpener will pay off in the long run. I have a Drill Doctor 750X which will sharpen up to a 3/4 " bit but there are smaller less expensive versions that will do the job. A Drill Doctor 350 will sharpen bits from 3/32" up to 1/2" and cost about $60.00. Of course there are other brands as well so just shop around. Keep in mind there are different ways to sharpen a bit so you should be familiar with the different kinds of points and make sure the sharpener you buy will do what you need it to. The standard point is the general purpose point that is used for softer materials like cold rolled steel, aluminum, and wood. The point can be 118 degrees or 135 degrees depending on what you are drilling. Soft metals like aluminum require 118 degrees and harder metals such as stainless steel and tool steel require 135 degrees. A split point bit is self centering and are generally used for tempered steels, hard alloys, or hard cast material. Titanium would require a slit point for example. All sharpeners are not capable of grinding a split point so be aware of that before purchasing. Keep your bits sharp and use cutting fluid and your drilling processes will be easier and you will have fewer broken bits and you probably won't need as many band aids!! 4 EAA1111.org .

Copy Link

Recommended publications

Machining Online Manufacturing Training
MACHINING ONLINE MANUFACTURING TRAINING MACHINING FUNDAMENTALS 5S Overview Cutting Processes Hole Standards and Inspection Math: Fractions and Decimals Thread Standards and Inspection Band Saw Operation Essentials of Heat Treatment of Steel Intro to OSHA Metal Cutting Fluid Safety Trigonometry: Sine, Cosine, Tangent Basic Cutting Theory Ferrous Metals Introduction to Mechanical Properties Noise Reduction/Hearing Conservation Units of Measurement Basic Measurement Fire Safety and Prevention Introduction to Metal Cutting Fluids Overview of Machine Tools Walking and Working Surfaces Basics of Tolerance Geometry: Circles and Polygons ISO 9001: 2015 Review Personal Protective Equipment Bloodborne Pathogens Geometry: Lines and Angles Lean Manufacturing Overview Powered Industrial Truck Safety Blueprint Reading Geometry: Triangles Lockout/Tagout Procedures Safety for Lifting Devices Calibration Fundamentals Hand and Power Tool Safety Math Fundamentals SDS and Hazard Communication GRINDING TECH Basic Grinding Theory Cylindrical Grinder Operation Grinding Variables Major Rules of GD&T Supporting and Locating Principles Basics of G Code Programming Dressing and Truing Grinding Wheel Geometry Metrics for Lean Surface Grinder Operation Basics of the Centerless Grinder Essentials of Communication Grinding Wheel Materials Process Flow Charting Surface Texture and Inspection Basics of the Cylindrical Grinder Essentials of Leadership Intro to Fastener Threads Setup for the Centerless Grinder Troubleshooting Basics of the Surface Grinder Grinding Ferrous
[Show full text]
Influence of Bio-Oils As Cutting Fluids on Chip Formation and Tool Wear During Drilling Operation of Mild Steel
International Journal of Recent Technology and Engineering (IJRTE) ISSN: 2277-3878, Volume-8 Issue-2, July 2019 Influence of Bio-Oils as Cutting Fluids on Chip Formation and Tool Wear during Drilling Operation of Mild Steel Jyothi P N, Susmitha M, Bharath Kumar M issues with regards to application, recycling and disposal of Abstract: The importance of health and environment has cutting fluids. Improper dispose of cutting fluids can cause forced Machining Industries to reduce the application of environmental and health issues. These issues created a Petroleum-based cutting fluid. But to ease the machining process pathway to the introduction of animal, mineral and vegetable and to increase the tool life, cutting fluids must be used. Research oils. A “Vegetable oil” is a triglyceride extracted from the has been done on vegetable oils as cutting fluids which is easy for disposal and does not affect the environment and the operator’s plant. Vegetable oils are classified into edible and non-edible health [1] . This paper discusses the machinability and tool life oils. Due to growing population and increased demands, using during drilling of a mild steel work piece using Neem, Karanja, of edible oils as lubricants is restricted. Non-edible vegetable blends of 50%Neem-50%Karanja, 33.3%Neem-66.6%Karanja, oils are an effective alternative. All tropical countries which 66.6%Neem-33.3%Karanja as cutting fluid. Results obtained are abundant resources of forests yield a significant quantity using petroleum-based oil are compared with the results obtained of oil seeds. by using above mentioned combination of oils and also with dry cutting conditions.
[Show full text]
Tribological Considerations of Cutting Fluids in Machining Environment: a Review
Vol. 38, No. 4 (2016) 463-474 Tribology in Industry www.tribology.fink.rs RESEARCH Tribological Considerations of Cutting Fluids in Machining Environment: A Review a a a a b A. Anand , K. Vohra , M.I. Ul Haq , A. Raina , M.F. Wani a Department of Mechanical Engineering, SMVD University, Katra, Jammu & Kashmir, India, b Centre for Tribology , National Institute of Technology, Srinagar, Jammu & Kashmir, India. Keywords: A B S T R A C T Tribology The paper presents a review to highlight the tribological aspects of Cutting fluids cutting fluids in machining environment. In this study, different Lubrication machining processes viz. turning, grinding, drilling and milling have Machining been considered with a special focus on grinding process. The cutting fluids are primarily used as coolants and lubricants in the various Corresponding author: machining processes. Different cutting fluids and the health hazards associated with their use have also been represented in this research A. Anand article. The paper also highlights the role of work materials and the Department of Mechanical Engineering, cutting tool materials from tribology point of view. The literature SMVD University, revealed that the development of biocompatible cutting fluids, recycling Katra, J&K, India. of cutting fluids, cutting fluids for high temperature tribological E-mail: [email protected] applications, studying the wetability characteristics with addition of nanoparticles, etc. can be taken up as study in order to enhance the tribological properties of the cutting fluids. © 2016 Published by Faculty of Engineering 1. INTRODUCTION emphasis on the role of tribology in the areas of energy conservation. It has been observed that In today’s competitive world, manufacturers and nearly 5.5 percent of U.S.
[Show full text]
Safety Data Sheet Product No. 812-650, 812-653 Cutting Fluid, Soluble Oil Issue Date (05-12-14) Review Date (08-31-17)
Safety Data Sheet Product No. 812-650, 812-653 Cutting Fluid, Soluble Oil Issue Date (05-12-14) Review Date (08-31-17) Section 1: Product and Company Identification Product Name: Cutting Fluid, Soluble Oil Synonym: SO Soluble Oil Company Name Ted Pella, Inc., P.O. Box 492477, Redding, CA 96049-2477 Inside USA and Canada 1-800-237-3526 (Mon-Thu. 6:00AM to 4:30PM PST; Fri 6:00AM to 4:00PM PST) Outside USA and Canada 1-530-243-2200 (Mon-Thu. 6:00AM to 4:30PM PST; Fri 6:00AM to 4:00PM PST) CHEMTREC USA and Canada Emergency Contact Number 1-800-424-9300 24 hours a day CHEMTREC Outside USA and Canada Emergency Contact Number +1-703-741-5970 24 hours a day Section 2: Hazard Identification 2.1 Classification of the substance or mixture OSHA/HCS status: This material is not considered hazardous by the OSHA Hazard Communication Standard (29 CFR 1910.1200). Not classified. GHS Pictograms: Void GHS Categories: Void 2.2 Label elements Hazard Pictograms: None Signal Word: None Hazard Statements: No known significant effects or critical hazards. Precautionary Statements: NA 2.3 Other hazards Defatting to the skin. Health Effects: NFPA Hazard Rating: Health: 2; Fire: 1; Reactivity: 0 HMIS® Hazard Rating: Health: 1; Fire: 1; Reactivity: 0 (0=least, 1=Slight, 2=Moderate, 3=High, 4=Extreme) Results of PBT and vPvB assessment: PBT: ND vPvB: ND Emergency overview Appearance: Clear Blue Liquid. Immediate effects: Warning! Causes eye irritation. Potential health effects Primary Routes of entry: Skin, ingestion. Signs and Symptoms of Overexposure: ND Eyes: Causes eye irritation.
[Show full text]
Effects of the Cutting Fluid Types and Cutting Parameters on Surface Roughness and Thrust Force
Proceedings of the World Congress on Engineering 2010 Vol II WCE 2010, June 30 - July 2, 2010, London, U.K. Effects of the Cutting Fluid Types and Cutting Parameters on Surface Roughness and Thrust Force E. Kuram, B. Ozcelik, E. Demirbas, and E. Şık Abstract- In this study, three different vegetable-based cutting De Chiffre [5] investigated effect of vegetable based cutting fluids developed from raw and refined sunflower oil and two oil on cutting forces and power. AISI 316L stainless steel commercial types (vegetable and mineral based cutting oils), workpieces were machined with drilling, core drilling, were carried out to determine for thrust force and surface reaming and tapping using HSS-E tools. From the roughness during drilling of AISI 304 austenitic stainless steel comparison of performance results obtained from two with HSSE tool. The uses of vegetable cutting oils was investigated in reducing thrust force and improve surface cutting fluids showed that the vegetable based cutting oils finish at different spindle speeds and feed rates during were better than the commercial mineral oil. Belluco and drilling. In the experiments, spindle speed, feed rate and De Chiffre [6] improved formulations of vegetable oils drilling depth were considered as machining parameters. which used as comparison with a mineral oil on surface integrity and part accuracy in reaming and tapping Index Terms- Drilling, Thrust force, Surface roughness, operations with AISI 316L stainless steel. The results with Cutting fluids, Vegetable based cutting fluids. the new formula were better than that of mineral oil. Later on De Chiffre and Belluco [7] used three vegetable based cutting oils including EP additives and a straight cutting I.
[Show full text]
Cutting Fluid Management: Small Machining Operations
University of Northern Iowa UNI ScholarWorks Iowa Waste Reduction Center Book Gallery Iowa Waste Reduction Center 2003 Cutting Fluid Management: Small Machining Operations Iowa Waste Reduction Center Let us know how access to this document benefits ouy Copyright ©2003 Iowa Waste Reduction Center Follow this and additional works at: https://scholarworks.uni.edu/iwrc_facbook Part of the Environmental Sciences Commons Recommended Citation Iowa Waste Reduction Center, "Cutting Fluid Management: Small Machining Operations" (2003). Iowa Waste Reduction Center Book Gallery. 12. https://scholarworks.uni.edu/iwrc_facbook/12 This Book is brought to you for free and open access by the Iowa Waste Reduction Center at UNI ScholarWorks. It has been accepted for inclusion in Iowa Waste Reduction Center Book Gallery by an authorized administrator of UNI ScholarWorks. For more information, please contact [email protected]. Manual2003 12/17/03 7:54 AM Page 2 © Copyright 2003 IOWA WASTE REDUCTION CENTER University of Northern Iowa Creation of this manual was funded by the U.S. Environmental Protection Agency, Risk Reduction Engineering Lab under Cooperative Agreement CR 821492-01-2. (Edition 1) The revision of this manual was funded by the U.S. Environmental Protection Agency, Office of Pollution Prevention and Toxics under a grant administered to the Small Business Pollution Prevention Center, Award Number X-82849601-3 (Edition 3) Cutting Fluid Management for Small Machining Operations Manual2003 12/17/03 7:54 AM Page 3 TABLE OF CONTENTS 1.0 INTRODUCTION
[Show full text]
Effect of Cutting Fluid on Micromilling of Ti-6Al-4V Titanium Alloy
Procedia Manufacturing Volume 5, 2016, Pages 332–347 44th Proceedings of the North American Manufacturing Research Institution of SME http://www.sme.org/namrc Effect of Cutting Fluid on Micromilling of Ti-6Al-4V Titanium Alloy Maksym Ziberov1, Márcio Bacci da Silva1, Mark Jackson2 and Wayne N.P. Hung3 1Federal University of Uberlandia, Uberlandia, Brazil. 2Kansas State University, Salinas, Kansas, USA 3Texas A&M University, College Station, Texas, USA. [email protected], [email protected], [email protected], [email protected] Abstract This paper studies the micromilling of Ti-6Al-4V titanium alloy. The main objective of this work is to study the performance of micromill tools in terms of burrs, machined surface and tool wear in machining of Ti-6Al-4V titanium alloy and evaluate the effect of the application of cutting fluid. Experimental micromilling tests with 152.4 Pm diameter WC tools were made. The tests were carried out on a four axis CNC milling machine with maximum spindle speed of 60,000 rpm and a resolution of 0.1 Pm. To measure the burr height, a profilometer with 1.0 mm measuring range and 16 nm resolution was used. The samples and tools were observed under scanning electron microscope to evaluate the machined surface quality, to measure wear and to analyse wear mechanisms. The results show that the application of cutting fluid has a large effect on the quality of the machined parts, both in terms of burrs formed and in terms of machined surface quality. Depending on the cutting conditions, the relative size of the burrs formed is much higher than in macromachining operations.
[Show full text]
Acoustic Emission Monitoring of Electrical Discharge Machining
ACOUSTIC EMISSION MONITORING OF ELECTRICAL DISCHARGE MACHINING ACOUSTIC EMISSION MONITORING OF ELECTRICAL DISCHARGE MACHINING By ALEXANDER W. GOODLET, B.ENG.MGT A Thesis Submitted to the School of Graduate Studies In Partial Fulfillment of the Requirements For the Degree Master of Applied Science McMaster University © Copyright by Alexander W. Goodlet, October 2013 MASTER OF APPLIED SCIENCE (2013) McMaster University (Department of Mechanical Engineering) Hamilton, Ontario TITLE: Acoustic Emission Monitoring of Electrical Discharge Machining AUTHOR: Alexander W. Goodlet, B.Eng.Mgt (McMaster University) SUPERVISOR: Dr. Philip Koshy NUMBER OF PAGES: 116 ii Abstract Electrical discharge machining (EDM) is a non-conventional machining process in which material removal is accomplished through spark erosion between a workpiece and tool electrode. Process stability is of great importance to the productivity of the EDM process, especially in the wire EDM configuration where an unstable process could lead to wire breakage having a detrimental effect on productivity. This thesis investigates the application of acoustic emission (AE) in EDM as a process monitoring technique. AE techniques have been applied to almost all machining processes; however its benefit as applied to EDM has not been investigated yet. The AE signal from the EDM process is related to various EDM parameters including, electrical parameters, tool materials, flushing and some process modifications, such as dispersing metallic powder into the gap. Using this knowledge, the benefits of using an AE sensor for a real-time process monitoring technique have been proven. iii Acknowledgements First and foremost, I would like to thank my supervisor, Dr. Philip Koshy. With his innovative ideas and constant strive to pursue exciting new research areas, it made working with him a rewarding experience.
[Show full text]
Troubleshooting Coolant Systems
TROUBLESHOOTING COOLANT SYSTEMS The problems most commonly attributed to aqueous cutting fluids are: Corrosion Nonferrous corrosion Rancidity or objectionable odors Objectionable residues Dirt accumulation Excessive foam Skin irritation Eye, nose, or throat irritation Unsatisfactory surface finish on parts Unsatisfactory cutting tool or grinding wheel life Problems with aqueous cutting fluids (‘coolants’) generally occur for one or more of the following reasons: Improper fluid selection for the metal type, machining operation, filter media, or water quality Lack of fluid maintenance or poor overall maintenance. Incorrect machine setup or operation. Excessive contamination from external sources. Improper fluid selection does occur; but usually, problems stem from tooling, poor maintenance, or excessive fluid contamination. Cutting fluids can seldom overcome incorrect tooling (materials, sharpening, feeds, speeds, or inadequate grinding wheel grades). Solving problems in a central system is more complex than solving problems in individual machines. It is not only necessary to locate the basic cause of the problem and take measures to correct it, but also to rejuvenate the central system cutting fluid, if possible, so that it will perform satisfactorily. Note: This publication contains information and recommendations based upon data obtained from sources considered reliable and believed to be correct, however, no warranty or guarantee is expressed or implied Houghton International Inc. Madison & Van Buren Aves., P. O. Box 930, Valley Forge, PA 19482 -0930 Phone: (610) 666-4000 / Fax (610) 666-1376 TROUBLESHOOTING COOLANT SYSTEMS CORROSION CONCERNS: Houghton cutting fluids provide corrosion control of the highest degree. Even with this protection, complaints of rust may occur from time to time. A step-by-step investigation is necessary to resolve the issue.
[Show full text]
Cutting Fluids (Coolants)
CUTTING FLUIDS (COOLANTS) Cutting fluid (metalworking fluid, coolant) is a liquid used in metalworking operations for reducing friction between the work piece and the tool and for removal of the heat generated by the friction. Metalworking operations . Benefits of metalworking fluids (coolants) . Factors of metalworking . Types of metalworking fluids (coolants) . Properties of some cutting fluids Metalworking operations Cutting (metalworking) fluids are involved in the following metalworking operations: . Cutting (separation of metal from a work piece in the form of chips) . Milling . Turning . Boring . Drilling . Broaching . Threading . Sawing . Abrading (rubbing away the surface by friction) . Grinding . Polishing . Lapping . Metal forming (changing the shape of a work piece by a pressure) . Rolling . Forging . Extrusion . Drawing . Deep drawing . Stamping Benefits of metalworking fluids (coolants) Lubrication and cooling effects provided by cutting fluids (coolants) result in the following benefits of metalworking: . Better surface finish. Cutting (metalworking) fluids lubricate the workpiece-tool metal-to-metal contact zone preventing tool galling and seizure, which assures good surface finish. Additives in lubricating oils#Extreme pressure additives|EP (extreme pressure) and other additives (sulfur, chlorine, phosphorous) enhance the lubricating effect of the fluids. Longer tool life. Temperature of a tool properly cooled by a cutting fluid (coolant) does not exceed the critical value, beyond which the tool hardness drops and its wear rate increases. Narrower tolerances of the work piece size. Cutting fluids provide both: decreasing the amount of heat generated in the workpiece-tool contact zone due to reduction of the friction (lubricating effect) and removing the heat (cooling effect). Thus cutting fluid stabilizes the work piece temperature providing better control of its geometry.
[Show full text]
Use of Castor Oil As Cutting Fluid in Machining of Hardened Stainless Steel with Minimum Quantity of Lubricant
Available online at www.sciencedirect.com ScienceDirect Procedia CIRP 26 ( 2015 ) 408 – 411 12th Global Conference on Sustainable Manufacturing Use of Castor Oil as Cutting Fluid in Machining of Hardened Stainless Steel with Minimum Quantity of Lubricant Mohamed Handawi Saad Elmunafi, D. Kurniawan, M.Y. Noordin* a,b,c Faculty of Mechanical Engineering Universiti Teknologi Malaysia, UTM Skudai, Johor 81300, Malaysia * Corresponding author. E-mail address: [email protected] Abstract Use of cutting fluids in machining processes can reduce the cutting temperature and provides lubrication to tool and workpiece. These translate to longer tool life and improved surface quality. Due to the issues of using fluids in machining related to environment, health, and manufacturing cost that need to be solved, options to reduce their use. A technique called minimal quantity lubrication (MQL), which sprays small amount of cutting fluid (in the range of approximately 10 – 100 ml/h) to the cutting zone area with the aid of compressed air, was developed to merge the advantages of both dry cutting and flood cooling. For the type of cutting fluids, vegetable oils are common cutting fluids used in MQL because of its superior lubrication and high-pressure performance. This study evaluates the performance of MQL using castor oil as cutting fluid. The workpiece is hardened stainless steel 48 HRC. Results are compared with dry cutting. It was found that using small amount of lubricant of 50 ml/h during the particular turning process produces better results compared to dry cutting, in terms of longer tool life. Surface roughness and cutting forces were also enhanced albeit slightly.
[Show full text]
High Speed Turning of Titanium (Ti-6Al-4V) Alloy
High Speed Turning of Titanium (Ti-6Al-4V) Alloy Anil Srivastava, Ph.D. Manager, Manufacturing Technology TechSolve, Inc., Cincinnati, OH 45237 Outline • Applications of Titanium Alloys • Technical Difficulties in Machining Titanium Alloys • High Speed Turning of Ti-6Al-4V Alloy • Some Recent Test Results • Conclusions 2 Application of Titanium Alloys • Titanium and its alloys are today used in: – Aerospace – Medical device – Food and chemical industries • Titanium alloys offers: – High strength-to-weight ratio – Super corrosion resistance – Bio-compatibility • Titanium alloys are difficult-to-machine due to: – Low thermal conductivity and diffusivity – High rigidity and low elasticity modulus – High chemical reactivity at elevated temperatures – Work hardening characteristics 3 Machining Titanium for Economical Production BASIC RULES • Use low cutting speeds – a change from 6 to 46 meters per min (20 to 150 sfpm) with carbide tools results in a temperature change from 427°C to 927°C (800°F to 1700°F). • Use high feed rates – a change from 0.05 to 0.51 mm/rev (0.002 to 0.020 in/rev) results in a temperature increase of only 149°C (300°F). • Use generous amounts of cutting fluid – coolant carries away heat, washes away chips, and reduces cutting forces. • Use sharp tools – replace them at the first sign of wear, or as determined by production/cost considerations. Complete tool failure occurs rather quickly after small initial amount of wear takes place. • Never stop feeding – while a tool and a workpiece are in moving contact. Permitting a tool to dwell in moving contact causes work hardening and promotes smearing, galling, seizing, and total tool breakdown.
[Show full text]