DOCSLIB.ORG

Port and Starboard Side of a Ship - Interesting Information

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Port and Starboard Side of a Ship - Interesting Information Shipping and Freight Resource Educational Blog http://shippingandfreightresource.com Port and Starboard side of a ship - interesting information Port and Starboard side of a ship - interesting information Most of you might have heard the term Port side and Starboard side in relation to a ship.. These are actually nautical terms which refer to the left and right side of the ship respectively when you are looking towards the Bow (the front of the ship - also known as Fore).. The rear of the ship is termed as Stern (also known as Aft).. There are many answers as to the evolution of the names Port & Starboard as below.. As per Wikipedia, before ships had rudders on their centrelines, they were steered by use of a specialized steering oar.. This oar was held by an oarsman located in the stern (back) of the ship.. However, like most of society, there were many more right-handed sailors than left- handed sailors. This meant that the steering oar (which had been broadened to provide better control) used to be affixed to the right side of the ship.. The term Port was derived from the practice of sailors mooring ships on the left side at ports in order to prevent the steering oar from being crushed.. From the Longboat museum in Oslo it is learned that a Viking longboat was steered by a large wooden plank called a "steer board".. The modern day equivalent is a "tiller" or "rudder".. The steer-board was operated by the helmsman facing forward and, since most people are right- handed, he would naturally hold the steer-board in his right hand.. Since the steer-board was always on the right, the right-hand side of the vessel became known as the steer-board side.. Subsequently the term "steer-board" blended into the English language and evolved into "starboard".. Another version is that, in the olden days before the advent of maps, navigation was done by following the arrangement of stars in the sky.. Usually old sailing ships had long masts & sails which disturbed the visibility of the helmsman and the sailors arranged a deck extending out on the right side to watch the stars & continue sailing.. So one person on the ship used to read the location of the starts sitting on the deck & convey the same to the Helmsman.. The deck that was used to look at the stars and decide the sailing route was termed as starboard deck.. Because of this extended deck on the right side, only the other side of the ship could be brought towards the port and it was named as port-side.. Once the modern centerpost rudder was developed, it was no longer necessary to dock with the vessel's port-side to port.. Ships now dock starboard or port-side alongside.. Another bit of interesting information is that the Starboard side has Green navigation lights and port side has Red navigation lights and the Aft of the ship has a white light.. If there are two vessels approaching each other head-on, each should alter course to starboard, so that they pass each other port-to-port unless otherwise communicated much like the rules of the road.. 1 / 2 Shipping and Freight Resource Educational Blog http://shippingandfreightresource.com Interesting isn't it..?? 2 / 2 Powered by TCPDF (www.tcpdf.org).
Load more

Recommended publications
  • 1850 Pro Tiller
    1850 Pro Tiller Specs Colors GENERAL 1850 PRO TILLER STANDARD Overall Length 18' 6" 5.64 m Summit White base w/Black Metallic accent & Tan interior Boat/Motor/Trailer Length 21' 5" 6.53 m Summit White base w/Blue Flame Boat/Motor/Trailer Width 8' 6" 2.59 m Metallic accent & Tan interior Summit White base w/Red Flame Boat/Motor/Trailer Height 5' 10" 1.78 m Metallic accent & Tan interior Beam 94'' 239 cm Summit White base w/Storm Blue Metallic accent & Tan interior Chine width 78'' 198 cm Summit White base w/Silver Metallic Max. Depth 41'' 104 cm accent & Gray interior Max cockpit depth 22" 56 cm Silver Metallic base w/Black Metallic accent & Gray interior Transom Height 25'' 64 cm Silver Metallic base w/Blue Flame Deadrise 12° Metallic accent & Gray interior Weight (Boat only, dry) 1,375# 624 kg Silver Metallic base w/Red Flame Metallic accent & Gray interior Max. Weight Capacity 1,650# 749 kg Silver Metallic base w/Storm Blue Max. Person Weight Capacity 6 Metallic accent & Gray interior Max. HP Capacity 90 Fuel Capacity 32 gal. 122 L OPTIONAL Mad Fish graphics HULL Shock Effect Wrap Aluminum gauge bottom 0.100" Aluminum gauge sides 0.090'' Aluminum gauge transom 0.125'' Features CONSOLE/INSTRUMENTATION Command console, w/lockable storage & electronics compartment, w/pull-out tray, lockable storage drawer, tackle storage, drink holders (2), gauges, rocker switches & 12V power outlet Fuel gauge Tachometer & voltmeter standard w/pre-rig Master power switch Horn FLOORING Carpet, 16 oz. marine-grade, w/Limited Lifetime Warranty treated panel
    [Show full text]
  • Use of Rudder on Boeing Aircraft
    12ADOBL02 December 2011 Use of rudder on Boeing aircraft According to Boeing the Primary uses for rudder input are in crosswind operations, directional control on takeoff or roll out and in the event of engine failure. This Briefing Leaflet was produced in co-operation with Boeing and supersedes the IFALPA document 03SAB001 and applies to all models of the following Boeing aircraft: 707, 717, 727, 737, 747, 757, 767, 777, 787, DC-8, DC-9, DC-10, MD-10, md-11, MD-80, MD-90 Sideslip Angle Fig 1: Rudder induced sideslip Background As part of the investigation of the American Airlines Flt 587 crash on Heading Long Island, USA the United States National Transportation Safety Board (NTSB) issued a safety recommendation letter which called Flight path for pilots to be made aware that the use of “sequential full opposite rudder inputs can potentially lead to structural loads that exceed those addressed by the requirements of certification”. Aircraft are designed and tested based on certain assumptions of how pilots will use the rudder. These assumptions drive the FAA/EASA, and other certifica- tion bodies, requirements. Consequently, this type of structural failure is rare (with only one event over more than 45 years). However, this information about the characteristics of Boeing aircraft performance in usual circumstances may prove useful. Rudder manoeuvring considerations At the outset it is a good idea to review and consider the rudder and it’s aerodynamic effects. Jet transport aircraft, especially those with wing mounted engines, have large and powerful rudders these are neces- sary to provide sufficient directional control of asymmetric thrust after an engine failure on take-off and provide suitable crosswind capability for both take-off and landing.
    [Show full text]
  • & Marine Engineering
    REFERENCE ROOM Naval Architecture & Marine Engineering ft* University of Michigan Ann Arbgr, M g109 THE UNIVERSITY OF MICHIGAN COLLEGE OF ENGINEERING Department of Naval Architecture and Marine Engineering DESIGN CONSIDERATIONS AND THE RESISTANCE OF LARGE, TOWED, SEAGOING BARGES J. L. Moss Corning Townsend III Submitted to the SOCIETY OF NAVAL ARCHITECTS AND MARINE ENGINEERS Under p. O. No. 360 September 15, 1967 In the last decade, -ocean-going unmanned barges have become an increasingly important segment of our merchant marine. These vessels, commonly over 400 feet long, and sometimes lifting in excess of 15,000 L.T. dead weight, are usually towed on a long hawser behind a tugboat. Because the barges are inherently directionally unstable, twin out- board skegs are attached to achieve good tracking. Model tests are conducted in order to determine towline resistance and the proper skeg position which renders the barge stable. Skegs, vertical appendages similar to rudders, are placed port and starboard on the rake. They create lift and drag, and move the center of lateral pressure aft, thus tending to stabilize a barge towed on a long line. At The University of Michigan many such model experiments have been conducted within the past several years. Since these tests have been carried out for various industrial con- cerns and on specific designs, systematic variations of parameters or other means of specifically relating the results have not been possible in most cases. Nevertheless, on the basis of the results of these largely unrelated tests, recom- mendations can be made regarding good design practice and some specific aspects can be demonstrated.
    [Show full text]
  • An Analytical Approach to the Question of a Clock Change
    An Analytical Approach to the Question of a Clock Change by Samuel Halpern One of the ongoing arguments that continues to be brought up is the question of whether or not clocks on Titanic were put back some time before the accident took place Sunday night, April 14, 1912. Some of the deck crew, awakened by the accident at 11:40 p.m. ship’s time, thought that it was close to the time that they were due to take their watch on deck, which would be at 12 o’clock. Despite Boatswain’s Mate Albert Haines, who was awake and on duty at the time, testifying that “The right time, without putting the clock back, was 20 minutes to 12,” there are some that try to argue that a 24 minute clock adjustment had already taken place, and the time of the accident on an unadjusted clock still keeping April 14th time would have been 4 minutes past 12. The underlying question that would resolve this issue is the run time from noon Sunday to the time of the accident. If the run time from noon to the time of the accident was 11 hours 40 minutes, then no clock change had yet taken place, and the time of collision was 11:40 p.m. in unadjusted hours. If the run time was more than 12 hours, then there was a clock change of some 23 or 24 minutes, and the time of collision was 11:40 p.m. in adjusted hours. It really is that simple. So how do we determine the actual run time from the available evidence that does not have to rely on subjective estimates such as time intervals or other measures that people may have perceived? The answer is to take an analytical approach to the problem using the taffrail log mileage data offered by quartermasters George Rowe and Robert Hichens at the inquiries.
    [Show full text]
  • Orientation Sheet for Horizon Updated: 2017-Apr-21
    Orientation Sheet for Horizon Updated: 2017-Apr-21 General • All voyages should be documented in the ship’s log book. Report any damage or deficiencies to [email protected] and to boat manager [email protected] / 410-203-2673 Specifications Registration #: MD 5596 AC Hull#: XLY 595267 Make: Islander 36 Year: 1977 Engine: Perkins 4.108; 4-cyl Diesel 48-HP Displacement: 13,450 lbs Draft: 5’ 02” Mast Height Fuel Capacity: 30 gal. Holding tank: 18 gal. (from waterline): 52’ 06” Water Capacity: 54 gal. 2 tanks, below Salon Settees LOA: 36’ 08" Batteries: House battery 1 and 2 (Starboard lazaret) LWL: 28’ 25” Starting Battery (under companionway steps) Beam: 11’ 17” Sails: Main, Genoa on furler, staysail with boom Safety Equipment First Aid Kit: Drawer port side Rescue Sling: Stern Rail PFDs: V-berth Fire Extinguishers: (2) – Starboard side cabin, Port quater berth Day/Night Flares: Aerial & Hand-held – Drawer port side above seats in salon Sounds (Horn, Bell & Whistle): Drawer port side above seats in salon Auto-Switched Bilge Pump: Wired directly to House Battery (must be switched to Auto when leaving boat). The switch is located on the starboard side inside the cabin above the galley sink Old Bilge Pump: Wired to Electric Panel on the engine compartment wall (manual mode only). Do not use this pump unless the other one is not working. Manual Bilge Pump: Cockpit Port side (handle located in drawer port side above seats) Anchors: Danforth (35 lbs) bow; Rode: 15’ of chain & 150’ of line (marked every 30’) Thru-hulls/Sea-cocks: Engine
    [Show full text]
  • An Orientation for Getting a Navy 44 Underway
    Departure and return procedure for the Navy 44 • Once again, the Boat Information Book for the United States Naval Academy Navy 44 Sailing Training Craft is the final authority. • Please do not change this presentation without my permission. • Please do not duplicate and distribute this presentation without the permission of the Naval Academy Sailing Training Officer • Comments welcomed!! “Welcome aboard crew. Tami, you have the helm. If you’d be so kind, take us out.” When we came aboard, we all pitched in to ready the boat to sail. We all knew what to do and we went to work. • The VHF was tuned to 82A and the speakers were set to “both”. • The engine log book & hernia box were retrieved from the Cutter Shed. • The halyards were brought back to the bail at the base of the mast, but we left the dockside spinnaker halyard firmly tensioned on deck so boarding crew could use it to aid boarding. • The sail and wheel covers were removed and stored below. • The reef lines were attached and laid out on deck. • The five winch handles were placed in their proper holders. • The engine was checked: fuel level, fuel lines open, bilge level/condition, alternator belt tension, antifreeze level, oil and transmission level, RACOR filter, raw water intake set in the flow position, engine hours. This was all entered into the log book. • Sails were inventoried. We use the PESO system. We store sails in the forward compartment with port even, starboard odd. •The AC main was de-energized at the circuit panel.
    [Show full text]
  • Boat Compendium for Aquatic Nuisance Species (ANS) Inspectors
    COLORADO PARKS & WILDLIFE Boat Compendium for Aquatic Nuisance Species (ANS) Inspectors COLORADO PARKS & WILDLIFE • 6060 Broadway • Denver, CO 80216 (303) 291-7295 • (303) 297-1192 • www.parks.state.co.us • www.wildlife.state.co.us The purpose of this compendium is to provide guidance to certified boat inspectors and decontaminators on various watercraft often used for recreational boating in Colorado. This book is not inclusive of all boats that inspectors may encounter, but provides detailed information for the majority of watercraft brands and different boat types. Included are the make and models along with the general anatomy of the watercraft, to ensure a successful inspection and/or decontamination to prevent the spread of harmful aquatic nuisance species (ANS). Note: We do not endorse any products or brands pictured or mentioned in this manual. Cover Photo Contest Winner: Cindi Frank, Colorado Parks and Wildlife Crew Leader Granby Reservoir, Shadow Mountain Reservoir and Grand Lake Cover Photo Contest 2nd Place Winner (Photo on Back Cover): Douglas McMillin, BDM Photography Aspen Yacht Club at Ruedi Reservoir Table of Contents Boat Terminology . 2 Marine Propulsion Systems . 6 Alumacraft . 10 Bayliner . 12 Chris-Craft . 15 Fisher . 16 Four Winns . 17 Glastron . 18 Grenada Ballast Tank Sailboats . 19 Hobie Cat . 20 Jetcraft . 21 Kenner . 22 Lund . 23 MacGregor Sailboats . 26 Malibu . 27 MasterCraft . 28 Maxum . 30 Pontoon . 32 Personal Watercraft (PWC) . 34 Ranger . 35 Tracker . 36 Trophy Sportfishing . 37 Wakeboard Ballast Tanks and Bags . 39 Acknowledgements . Inside back cover Boat Compendium for Aquatic Nuisance Species (ANS) Inspectors 1 Boat Terminology aft—In naval terminology, means towards the stern (rear) bow—A nautical term that refers to the forward part of of the boat.
    [Show full text]
  • Sea Kayak Handling Sample Chapter
    10 STERN RUDDERS Stern rudders are used to keep the kayak going in a straight line and make small directional changes when on the move. The stern rudder only works if the kayak is travelling at a reasonable speed, but it has many applications. The most common is when there is a following wind or sea pushing the kayak along at speed. In this situation, forward sweep strokes are not quick enough to have as much effect as the stern rudder. A similar application is when controlling the kayak while surfi ng. A more ‘gentle’ application is when moving in and out of rocks, caves and arches at slower speeds. Here, the stern rudder provides control and keeps the kayak on course in these tight spaces. Low angle stern rudder This is the classic stern rudder and works well to keep the kayak running in a straight line. It is best combined with the push/pull method of turning with a stern rudder (see below). • The kayak must be moving at a reasonable speed. • Fully rotate the body so that both hands are out over the side. • Keep looking forwards. • Place the blade nearest the stern of the kayak in the water as far back as your rotation allows. • The blade face should be parallel to the side of the kayak so that it cuts through the water and you feel no resistance. 54 • The blade should be fully submerged and will act like a rudder, controlling the direction of the kayak. • The front hand should be across the kayak and at a height between your stomach and chest.
    [Show full text]
  • Touring Rudder Sit-On Top Kit Kit to Fit Rudder Enabled Sit-On Tops with a 10Mm Rudder Fixing Point
    touring rudder sit-on top kit Kit to fit rudder enabled sit-on tops with a 10mm rudder fixing point. Note: It is easier to fit the Touring Rudder System if you have a screw hatch fitted to the rear stowage area of the kayak. If your kayak does not have this screw hatch and you wish to fit one, please contact a Perception dealer for advice. These instructions explain how to fit the rudder kit to a kayak with or without a rear screw hatch in place. Please make sure you follow the correct steps for your version of sit-on top kayak. This kit should contain the following: 1x rudder assembly with up-haul rope & split ring 4x deck fittings 4x length of rudder hose 5x self tapping screws 2x Dyneema control line - with cord end assembly 2x oval toggle 1x pair of Tip-Toes control footrests with foam washers 1x length of 4mm shock cord 6x footrest screws, washers and nuts - pre-fitted 1x rudder park - inc. hook, shock cord & fixing block You will also require some tools to fit this kit: Drill with 3mm, 5mm and 6mm drill bits Marker pen Short phillips screwdriver Wire cutters Small adjustable spanner or pair of pliers Lighter Tape measure Small amount of sticky tape Please read these instructions carefully before fitting! Step 1 - Control line entry points The rudder will need to have two control lines attached, each one running through hose sections inside the kayak from the rudder to the Tip-Toes footrests. This kit has four hose sections (two pairs) as two sections are needed per control line.
    [Show full text]
  • Gannet Electronics
    Gannet Electronics A Summary of the Electronic Equipment Fitted to early Model R.A.N Gannet A.S.1 Aircraft Prepared by David Mowat Ex-L.R.E.M.(A) 21st. August 2003 Page 1 Page 2 GANNET ELECTRONIC EQUIPMENT Introduction The ‘Heart’ of the Gannet as a Weapons System was its Electronic Equipment. It contained a comprehensive range of electronic equipment to enable it to perform the various roles for which it was designed. Its Primary Role was to detect, locate, and destroy enemy submarines. For this Role, the Aircraft was fitted with a Search Radar and Sonobuoy Systems. Other electronic systems were also installed for Communications, both internal and external, and Navigation. The various equipments were allocated an ‘Aircraft Radio Installation’ (ARI) number, which specified the actual equipment used in each installation. These may vary between aircraft depending on the role that the particular aircraft was to perform. A cross- reference List of ARI’s is shown at Appendix ‘A’. The various equipments can be grouped into four major categories as follows: a.! Communications b.! Navigation c.! Warfare Systems d.! Stores Communications Equipment The Communications Equipment was used to enable the crew to talk to each other (internal communications) and other aircraft, ships or bases (external communications). They are as follows: a.! Audio Amplifier Type A1961 The Type A1921 was used to amplify the Microphone outputs from the three crew members and feed it back into the earphones. It was located on the port side of the rear cockpit at about seat height just forward of the Radio Operator.
    [Show full text]
  • 19750827-0 DC-3 5Y-AAF.Pdf
    1 CAV/ACC/24/75 ACCIDENT IUVESTIGATION BRANCH CIVIL AIRCRAFT ACCIDEiiT Report on the Accident to Douglas DC-3 Aircraft Registration number 5Y-AAF which occurred on the 27th August,1975 At 0922 hours, at Mtwara Airport, Tanzania. E A S T A F R I CAN C 0 M M U NIT Y AOCIDEwr REPORT AOCIDE:~T INVESTIGATIOn BRAl'WH 'CIVIL ACCIDENT REPORT CAV/ACC/24/75 AIRCRAFT TYPE 8; HEGISTRATION: Douglas DC-::- 5Y-l~ ENGINE: Pratt & \filii tney R1830-90D REGISTERED OWlIJ]~R & OPERATOR: East African Airways Corporation, P.O. Box 19002, NAIROBI, Kenya. CREVf: CAPTAIN Gabriel Sebastian Turuka ) ) Uninjured FIJ:1ST OFFICER Steven Robert Wegoye ) PASSENGER: Sixteen - Uninjured. PLACE OF ACCIDEHT: ~,1twara Airport, Tanzania. DATE AND T1MB: 27th August, 1975, 0922 hours. ALL rrU'lES IN THIS REPORT ARE G.1VI. T. SUMMARY The aircraft was operating East African Airways Service flight number EC037 from Dar es Salaam to Nachingmea with an unscheduled refuelling stop at I1twara with 3 crew and 16 passengers on board. The flight from Dar es Salaam was uneventful and an approach and landing was made onto runway 19. After touch down the aircraft swung to the left and then to the right, after which it left the runway where both main landing gear assys collapsed causing substantial daLage to the centre section and nacelle structure. The report concludes that the most probable cause of the accident was the failure of the pilot to initiate corrective action to prevent the aircraft from turning off the runway. 1.1 HISTORY OF THE FLIGHT: The aircraft departed Dar es Salaam with three crew and 16 passengers.
    [Show full text]
  • Aerosport Modeling Rudder Trim
    AEROSPORT MODELING RUDDER TRIM Segment: MOBILITY PARTS PROVIDERS | Engineering companies Application vertical: MOBILITY AND TRANSPORTATION | AircraFt Application type: FINAL PART: Short runs THE CUSTOMER FINAL PART: SHORT RUNS AEROSPORT MODELING RUDDER TRIM COMPANY DESCRIPTION APPLICATION TRADITIONAL MANUFACTURING Some planes are equipped with small tabs on the control surfaces (e.g., rudder trim Assembly of 26 different machined and standard parts Aerosport Modeling & Design was established in tabs, aileron tabs, elevator tabs) so the pilot can make minute adjustments to pitch, September 1996, and since then, they have worked to yaw, and roll to keep the airplane flying a true, clean line through the air. This produce the highest-possible quality prototypes, improves speed by reducing drag from the larger, constant movements of the full appearance models, working models, and machined rudder, aileron, and elevator. parts, and to meet or exceed client expectations. The company strives to be seen as a partner to their Many airplanes also have rudder and/or aileron trim systems. On some, the rudder clients and an extension of their design and trim tab is rigid but adjustable on the ground by bending: It is angled slightly to the development team, not just a supplier of prototyping left (when viewed from behind) to lessen the need for the pilot to push the rudder services. pedal constantly in order to overcome the left-turning tendencies of many prop- driven aircraft. Some aircraft have hinged rudder trim tabs that the pilot can adjust Aerosport Products spun off from sister company in flight. Aerosport Modeling & Design in 2009 to develop products for experimental aircraft, the first of which When a servo tab is employed, it is moved into the slipstream opposite of the was the RV-10 Carbon Fiber Instrument Panel.
    [Show full text]