DOCSLIB.ORG

Surge Protective Devices (SPD) SPEEDFAXTM Section

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Surge Protective Devices (SPD) SPEEDFAXTM Section Surge Protective Devices (SPD) SPEEDFAXTM Section c o n t e n t s Siemens Residential and Commercial Surge Protective Devices Scan to connect online to the most up-to- Family SPDs 10-2 date version of SOLID Protection 10-3 this Section of SPEEDFAX. BoltShield™ Surge Protective Devices 10-4 – 10-5 First Surge 10-6 – 10-7 TPS3 01 and TPS3 L1 (10 Mode) 10-8 TPS4 01 and TPS4 L1 (10 Mode) 10-9 TPS3 02 and TPS3 L2 (10 Mode) 10-10 TPS3 03 10-11 TPS3 03 DC 10-12 TPS3 05 and TPS3 L5 (10 Mode) 10-13 TPS4 05 and TPS4 L5 (10 Mode) 10-14 TPS3 06 and TPS3 L6 (10 Mode) 10-15 TPS4 06 and TPS4 L6 (10 Mode) 10-16 TPS3 09 10-17 TPS3 11 10-18 TPS3 12 and TPS3 L12 (10 mode) 10-19 TPS3 15 and TPS3 L15 (10 mode) 10-20 Frequently Asked Questions 10-21 Internally Mounted SPDs External or Wall Mounted SPDs Residential SPDs See pages 10-9 – 1-52 Features Features Features n Per Phase Surge Current Capacity n Per Phase Surge Current Capacity n Per Phase Surge Current Capacity ranging from 100 kA to 500 kA ranging from 50 kA to 1000 kA of 40, 50, 60, 100 or 140 kA n n n Industry best VPRs Industry best VPRs Complete Service Protection for 10 n In = 20 kA (most models) n In = 20 kA (most models) - Power n Across the board UL 96A compliance n Across the board UL 96A compliance - Telephone (most models) (most models) - Coax SPD n n Ground Reference Monitoring Ground Reference Monitoring n Ground Reference Monitoring (GRM) diagnostics (GRM) diagnostics (GRM) diagnostics (excluding TPS3 03 & TPS3 09) (Section was last modified on 08/13/21) Siemens Industry, Inc. SPEEDFAX™ Product Catalog 10-1 Revised on 07/31/21 SPD - Surge Protective Devices Siemens Surge Protection Innovations Introduction In today’s electronic world, home and TranSafe circuitry, coordinated fusing The BoltShield line of SPDs helps business electrical systems just aren’t and thermal cutouts, dielectric isolation, address the changing NEC codes that complete unless they incorporate surge mechanical re-enforcing taping, etc… require surge protection in all dwellings. protection. Stopping Surges Before resulting in a design that ensures the The Siemens BoltShield family of They Get Into these systems is best highest possible electrical system surge residential and commercial products accomplished through the installation protection and reliability. allows this to be done easily and at a reasonable cost. of appropriately sized hard-wired surge Our next generation UL 1449 4th Edition protective devices (SPDs) beginning at the TPS SPDs carry on this same legacy. Electrical disturbances will always incoming service followed by installations Every TPS is infused with Siemens occur, but they don’t have to cause at other key surge entry points. engineering safety and performance surge protectors to fail in an unsafe When Siemens first developed the “know-how.” Siemens SPDs have the manner. Safer surge protection means Transient Protection System (TPS) family highest degree of safety while delivering uncompromised electrical system of surge protectors, we knew early the industry’s best performance protection, safety, and reliability. on that hard-wired surge protectors ratings – some of the lowest Voltage The following pages provide additional needed fully coordinated safety controls. Protection Ratings (VPRs), Type 1 or 2 technical and ordering information This led to the adoption of a number and 20 kA I-nominal ratings (for most concerning our entire offering of surge of SPD industry safety control firsts models) with surge current ratings protection devices. including the patented Ceramgard and from 50 to 1000 kA. Surge Protector Per Phase Surge Current Capacities Internal and Wall Mounted Standard Mode Per Phase TPS3 01 TPS4 01 TPS3 02 TPS3 03 TPS3 03 TPS3 05 TPS4 05 TPS3 06 TPS4 06 TPS3 09 TPS3 11 TPS3 12 TPS3 15 Surge DC Current 50 kA 100 kA 150 kA 200 kA 250 kA 300 kA 400 kA 500 kA 600 kA 800 kA 1000 kA 10 Mode SPDs Per Phase TSP3 L1 TSP4 L1 TPS3 L2 TPS3 L5 TPS4 L5 TPS3 L6 TPS4 L6 TPS3L 12 TPS3L 15 Surge Current 100 kA 10 150 kA 300 kA SPD 450 kA 500 kA 550 kA 600 kA 750 kA 900 kA 10-2 Siemens Industry, Inc. SPEEDFAX™ Product Catalog Siemens / Speedfax Previous folio: new page From Julie at APTTVSS Revised on 07/31/21 SPD - Surge Protective Devices Recommending Surge Protection SOLID Protection Either at home or in the work place, generated by the day to day operations government studies, the most efficient nearly every electrical load is electronic of equipment like washers and dryers, way to protect electrical systems from infused. With today’s power quality copiers, chillers, etc. surges is through the installation of being the same as it was 50 years ago, hardwired SPDs at key points throughout the distribution system. These locations equipment is more susceptible to surge In response to this susceptibility, code authorities have mandated emergency can easily be remembered by memorizing damage and/or disruption generated the locations of the acrostic found within by normal electrical distribution power distribution equipment now must be protected by a listed SPD. the following phrase, “The best surge interactions. Places where lightning The reasoning is based upon anecdotal protected system is a SOLID one,” where activity is minimal are now experiencing understating that surge protected each letter of the word SOLID stand for more electronic failures due to surges systems are more reliable. Supported by the locations on the electrical system where SPDs should be installed. The illustration to the right shows S O L I D “SOLID” locations for a school’s electrical system. Under each ‘SOLID’ location is a Siemens TPS model number with surge current capacities matching those to what are typically specified by consultants across North America. TPS30620 / TPS30515 / TPS30110 / TPS31110 TPS30350 TPS40620 TPS40515 TPS40110 or or or or or TPS30910 Call TPS Group TPS31220 TPS31215 TPS31110 Service Outside loads Lower voltage Individual Data, Entrance like Parking distribution critical telephone, Lot Lighting panels equipment and coaxial powered powering like servers cables from computers distribution and other panels electronics Surge Arrestor Replacement Discrete or True 10 Mode Style SPDs Low-voltage surge and lightning For mission critical or high profile applications, arrestors became obsolete when A B C NG a growing number of end users prefer the assur- UL 1449 3rd edition went into MOVs MOVs MOVs MOVs ance discrete or true 10-mode SPDs provide. effect in 2009. MOVs When surges traverse the electrical system They were replaced with Type MOVs via phase to phase conductors, standard SPDs 1 SPDs having an I-nominal (In) MOVs indirectly protect via the line to neutral or line to rating equal to 20 kA. Most all MOVs ground modes of protection. Siemens integral Siemens TPS3s are rated as MOVs or wall mounted “Discrete” or “True” 10-mode Type 1, I =20 kA SPDs. However, SPDs address L-L surges by incorporating n MOVs TPS3 03 the style and form factor of tra- directly connected line to line surge protection Type 1 SPD ditional surge arrestors is best elements. This style of SPD provides the “Just with I = 20 kA replaced using our TPS3 03. MOVs = Parallel MOVs in Case” assurance mission critical or high pro- n file projects require. 10 SPD Siemens Industry, Inc. SPEEDFAX™ Product Catalog 10-3 Revised on 03/31/20 BoltShield™ Surge Protective Devices BSPD – Commercial Surge Protection for Panel Boards Catalog Logic BSPD series for panelboards Ordering Information Catalog # BSPD – 2 – A – 100 Series Poles Voltage Code Surge Current Rating BSPD 2 = 2 Pole A = 120/240V, 1Ø 3W (Fig.1) 100 = 100kA per Mode/Phase 3 = 3 Pole B = 240/120V, 3Ø 4W (Fig.3) C = 208Y/120V, 3Ø 4W (Fig.2) D = 240V, 3Ø 3W (Fig.4) E = 480Y/277V, 3Ø, 4W (Fig.1) F = 480V, 3Ø, 3W (Fig.4) G = 600V, 3Ø, 3W (Fig.4) K = 380Y/220V, 3Ø, 4W (Fig.1) L = 600Y/347V, 3Ø, 4W (Fig.1) S = 400Y/230V, 3Ø, 4W (Fig.1) T = 415Y/240V, 3Ø, 4W (Fig.1) BSPD Series Product specifications General specifications Diagnostic monitoring specifications Design specifications Maximum surge current rating range 100 kA per phase Green/red visual mechanical flag Monolithic distribution grade MOV failure indicators UL Type designation SPD Type 1b Flashing dual color LED (green/red) Integrated optimized thermal protection UL 1449 I-nominal rating 20kA status indicator UL 1449 short circuit current rating 200kA Audible alarm with Fits in footprint of BL/BQD, or xGB/3VA41c silence switch/button Repetitive impulse 5,000 hits Form C dry contact, 240V AC, Modes of protection (L-N or L-G, L-L) Response time <1 ns 1A max, 48V DC, 0.5A max BSPD Catalog Numbers and UL 1449 performance data Catalog numbers System voltage L-N (L-G) L-L In SCCR MCOV Siemens breaker form factor BSPD2A100 120/240V, 1Ø, 3W 600V 900 20kA 200kA 150V 2-P, BL/BQD or xGB/3VA41 BSPD3B100 240/120V, 3Ø, 4W 600V/800V 1200 20kA 200kA 150V 3-P, BL/BQD or xGB/3VA41 BSPD3C100 208Y/120V, 3Ø, 4W 600V 900 20kA 200kA 150V 3-P, BL/BQD or xGB/3VA41 BSPD3D100 240V, 3Ø, 3W 800V 1500 20kA 200kA 280V 3-P, BL/BQD or xGB/3VA41 BSPD3E100 480Y/277V, 3Ø, 4W 1000V 1800 20kA 200kA 320V 3-P, BL/BQD or xGB/3VA41 BSPD3F100 480V, 3Ø, 3W 1800V 3000 20kA 200kA 550V 3-P, BL/BQD or xGB/3VA41 BSPD3G100 600V, 3Ø, 3W 2000V 4000 20kA 200kA 700V 3-P, BL/BQD or xGB/3VA41 BSPD3K100 380Y/220V, 3Ø, 4W 900V 1800 20kA 200kA 320V 3-P, BL/BQD or xGB/3VA41 BSPD3L100 600Y/347V, 3Ø, 4W 1200V 2500 20kA 200kA 400V 3-P, BL/BQD or xGB/3VA41 BSPD3S100 400Y/230V, 3Ø, 4W 900V 1800 20kA 200kA 320V 3-P, BL/BQD or xGB/3VA41 BSPD3T100 415Y/240V, 3Ø, 4W 900V 1800 20kA 200kA 320V 3-P, BL/BQD or xGB/3V Benefits of installing multiple BSPDs Adding multiple BSPDs in a single panelboard can increase modes of protection and a surge capacity.
Load more

Recommended publications
  • The ABC's of Lightning
    DEHN, INC. The ABC’s of Lightning TO BE SURE, USE DEHN® Lightning represents a stunning combination of nature’s beauty and awesome power Lightning currents conducted in modern electrical circuits can cause immediate and catastrophic equipment failure. Surges from induced lightning and power switching operations are smaller but are more numerous and can result in equipment misoperation, lockup or damage. DEHN®’s mission is “to protect life and property from the hazards of lightning and surges.” Lightning cannot be prevented, but proper use of DEHN®’s Lightning and Surge protection can safely divert lightning currents away from ourselves, our homes and our businesses. DEHN® has been providing Surge and Lightning Protection around the world for over 90 years. Currently employing a staff of over 1000 highly qualified personnel throughout the world, DEHN® is active in over 50 countries. DEHN® invests heavily in research and development, and is active in contributing and exchanging information with others at international technical conferences. The information contained in this catalog is as complete and accurate as possible. However DEHN® Inc., reserves the right to make changes to product specification and data without advance notice or obligation. © COPYRIGHT 2002 DEHN®, Inc. The ABC’s of Lightning and Surges A surge is a very short burst of voltage, which if In addition, the Rocky, Appalachian, and Sierra not suppressed, can cause equipment failure or lockup. Nevada mountain ranges have low ratio of cloud to cloud vs The duration of a surge is less than 1/1000 of a second. cloud to ground which means that a higher percentage Measurements of actual lightning strikes have shown of strikes reach the ground.
    [Show full text]
  • Silicon Surge Protector
    CAT.No.U０２９-４ SILICON SURGE PROTECTOR SHINDENGEN ELECTRIC MFG. CO., LTD. SILICON SURGE PROTECTOR ■The products shown in this catalog are intended for use in standard applications requiring normal，commercial levels of reliability. lf these products are to be used in equipment or devices requiring special or specific levels of quality and reliability in which failure or malfunction of a product may directly affect human life or health，contact the local SHINDENGEN office to confirm that the intended use of the product is appropriate. The quality levels of our products are defined below： Standard Applications Computers， office automation， communication terminals， test and measurement instrumentation，AV equipment，video games and related amusement equipment，home appliances，machine tooIs，industrial robots， personal equipment，etc. Special AppIications Transportation（ automotive， marine， etc.） trunk-line communication， traffic signal equipment，commercial fire prevention/anti-theft equipment， various safety devices，medical equipment，etc. Specific Applications Nuclear power controIs，aerospace and aeronautical equipment，submarine relay equipment，devices and systems for preserving life，etc. ■Although efforts are constantIy made to improve quality and reliability，please select a product after careful examination so that personal injury，accidents and social damage can be prevented as a result of deploying measures such as a redundant design，designs that prevent the spreading of fire，designs that prevent malfunctions and so forth while taking safety into consideration as necessary. One of the most important issues regarding the construction of a high-level information system is to protect the electronic equipment and systems against various disasters. SHINDENGEN is proud to introduce our line of high-performance Silicon Surge Protectors，which are suited to a wide variety of digitaI applications.
    [Show full text]
  • Motor Surge Protection Type MSP
    Motor Surge Protection ̈̈̈̈̈ Type MSP ̈ 2.4 to 24 kV ̈ Surge protection for critical industrial loads: • Large motors and generators Specialty Capacitors • Large transformers • Medium-voltage switchgear and motor control centers Electrical distribution systems are subject to power surges, switching transients, faults, and lightning strikes at anytime. Such occurrences can be damaging to electrical systems, as well as various apparatus used in a manufacturing process. ABB offers the Type MSP,a protective device that provides protection for motors, rotating machines, and transformers, and yields assurance of continuous operation of the equipment, the electrical system, and the manufacturing process. The primary function of the Type MSP motor surge protector is to guard the winding insulation of the device being protected. Station class, metal oxide lightning arresters act to limit the maxi- mum voltage to the device to a predetermined magnitude. Specially designed surge capacitors, connected in parallel with the arresters, control the rate of rise of the resultant overvoltage. The combination of surge arresters and surge capacitors serve to limit the turn-to-turn insulation stress impressed on the device being protected. STANDARD FEATURES ̈ Rugged-welded 11-gauge metal enclosure ̈ Indoor NEMA 1/12" enclosure ̈ ANSI #61 light gray paint ̈ Heavy-duty rated surge capacitors ̈ Station class MOV surge arresters ̈ Copper bus bars ̈ Common ground connections OPTIONAL ̈ Hinged, padlockable front door ̈ Outdoor NEMA 3R enclosure ̈ Removable cable entry plates for top ̈ NEMA 4X stainless steel enclosure or bottom feed ̈ Intermediate class MOV surge arresters All ABB products are IndustrialIT enabled.
    [Show full text]
  • Varistors: Ideal Solution to Surge Protection
    Varistors: Ideal Solution to Surge Protection By Bruno van Beneden, Vishay BCcomponents, Malvern, Pa. If you’re looking for a surge protection device that delivers high levels of performance while address- ing pressures to reduce product size and compo- nent count, then voltage dependent resistor or varistor technologies might be the ideal solution. ew regulations concerning surge protection limit the voltage to a defined level. The crowbar group in- are forcing engineers to look for solutions cludes devices triggered by the breakdown of a gas or in- that allow such protection to be incorpo- sulating layer, such as air gap protectors, carbon block de- rated at minimal cost penalty, particularly tectors, gas discharge tubes (GDTs), or break over diodes in cost-sensitive consumer products. In the (BODs), or by the turn-on of a thyristor; these include automotiveN sector, surge protection is also a growing ne- overvoltage triggered SCRs and surgectors. cessity—thanks to the rapid growth of electronic content One advantage of the crowbar-type device is that its very in even the most basic production cars combined with the low impedance allows a high current to pass without dissi- acknowledged problems of relatively unstable supply volt- pating a considerable amount of energy within the protec- age and interference from the vehicle’s ignition system. tor. On the other hand, there’s a finite volt-time response Another growing market for surge protection is in the as the device switches or transitions to its breakdown mode, telecom sector, where continuously increasing intelligence during which the load may be exposed to damaging over- in exchanges and throughout the networks leads to greater voltage.
    [Show full text]
  • ISOLATOR/SURGE PROTECTOR 118Ka BACKGROUND
    LITERATURE ISOLATOR/SURGE PROTECTOR 118kA BACKGROUND This addendum to “The Isolator/Surge Protector” describes the operation of the ISP in greater detail. It is assumed that the reader has already read the ISP Introduction for a general discussion of the features and characteristics. To reiterate some of the ISP introduction material, the ISP blocks the flow of DC current and readily conducts AC current as long as the absolute value of the voltage across its terminals is less than a preselected voltage threshold level (12.5 or 20 volts) and the steady-state AC current is also within its rating. If either of these conditions are exceeded, the ISP momentarily transitions from its “blocking DC/conducting AC” mode to a virtual short circuit to both AC and DC. This transition is accomplished within 1 to 4 microseconds by the logic-controlled circuit turning ON thyristor T1 or T2 (depending on polarity). This protects the DC blocking/AC by-pass capacitor from failure due to excessive current. It also provides over-voltage protection between the two points to which the ISP is connected. Reference Figure 1 for a simplified diagram of the ISP showing all key circuit elements. Figure 1: Isolator/Surge Protector Circuit Figure 2: Simplified Isolator/Surge Protector DURING DC CONDITIONS Whenever the DC voltage exceeds the voltage transition level selected, cathodic isolation is then interrupted until the transient The ISP appears as an open circuit to any DC voltage up to condition which caused the ISP to transition to its shorted mode the 12.5 or 20 volt peak transition level selected.
    [Show full text]
  • TECH TIP – What Is Varistor?
    TECH TIP – What is Varistor? A varistor is a voltage dependent resistor (VDR). The resistance of a varistor is variable and depends on the voltage applied. The word is composed of parts of the words “variable resistor”. Their resistance decreases when the voltage increases. In case of excessive voltage increases, their resistance drops dramatically. This behavior makes them suitable to protect circuits during voltage surges. Causes of a surge can include lightning strikes and electrostatic discharges. The most common type of VDR is the metal oxide varistor or MOV. A varistor typically comes in a disc package: Characteristics A voltage dependent resistor has a nonlinear varying resistance, dependent on the voltage applied. The impedance is high under nominal load conditions, but will sharply decrease to a low value when a voltage threshold, the breakdown voltage, is exceeded. They are often used to protect circuits against excessive transient voltages. When the circuit is exposed to a high voltage transient, the varistor starts to conduct and clamps the transient voltage to a safe level. The energy of the incoming surge is partially conducted and partially absorbed, protecting the circuit. The most important selection parameter is the clamping voltage. It is recommended to use as high clamping-voltage as the protected circuit allows, to limit the amount of exposure to surges. For example, to protect 120VAC circuits, you would use an MOV rated at 150V as long as the circuit would allow voltages up to 150V. Varistors are useful for short duration protection in case of high transient voltage surges in the order of 1-1000 microseconds.
    [Show full text]
  • Stock Products Catalog
    2016 Stock Products Catalog EFFECTIVE January 1, 2016 PRIME WIRE & CABLE, Inc. 280 Machlin Court, City of Industry, CA 91789-3026 Industrial Products Division: Toll Free: (800) 962-2738 Fax: (800) 797-2226 Retail Products Division: Toll Free: (888) 445-9955 Fax: (909) 859-2926 www.primewirecable.com Table of Contents OUTDOOR EXTENSION CORD S ................................................................................................................. 4-7 Bulldog Tough ® Cords, Generator Cords & Adapters, TPE-Rubber Arctic Blue ™ All Weather Cords, Glacier Flex ® Cold Weather Cords, High Visibility Neon Flex ® Cords, Kaleidoscope of Colors ® Cords, Primelok ® Locking Connector Cords, No-Overload ® Circuit Breaker Cords, Farm & Shop Cords, Rubber Cords, Landscape Cords, Outdoor Cords, Outdoor Triple Tap Cords, Outdoor Twist-to-Lock Cords SHOCK-SAFE ® G.F.C.I. PRODUCT S................................................................................................................7 WIRING DEVICE S ........................................................................................................................................7 APPLIANCE & POWER SUPPLY CORD S..........................................................................................................8 Range & Dryer Cords, Air Conditioner Cords, Power Supply Cords HOUSEHOLD & UTILITY CORD S.................................................................................................................8-9 Household Cords, Snug Plug ® Cords, Office Cords, Shop and Utility
    [Show full text]
  • 3 Keys to Choosing a Surge Protector
    3 KEYS TO CHOOSING A SURGE PROTECTOR There are many different kinds of surge protectors. Surge protectors installed on power lines don’t absorb or otherwise diminish damaging power surges. Their primary function is to divert these destructive forces away from your sensitive circuitry. There are four basic kinds of surge protectors: metal oxide varistors (MOVs), avalanche diodes, filters, and gas tubes. Metal oxide varistors (MOVs) are a common choice. The word varistor is a combination of two words: variable resistor. As these words imply, an MOV is a highly resistive device that triggers during an AC power surge and diverts the excess voltage, preventing it from reaching your expensive computer equipment. MOVs are designed to accommodate surge levels up to a specified breakdown voltage. When this limit is exceeded, the MOV varies from a highly resistive state to a state of low resistance. The excess energy is “clipped” from the power line and sent to ground. Surges occurring at the peak of a sine wave are clipped by the MOV, but high-voltage spikes may still occur (though they’ll eventually be clipped), and the MOV response times can range up to 500 picoseconds. This is the primary weakness of an MOV, but it’s usually overcome by the inclusion of some other suppression technique within the surge protector. Avalanche diodes, also known as Zener diodes, are semiconductor devices similar to MOVs, but they feature much faster response times (usually less than one picosecond). Avalanche diodes are available in a wider range of sizes to provide accurate and repeatable voltage clamping.
    [Show full text]
  • MSP™ - Medium Voltage Motor Surge Protection
    66 Carey Road | Queensbury, NY | 12804 Ph: (518) 792-4776 | Fax: (518) 792-5767 www.nepsi.com | [email protected] MSP™ - Medium Voltage Motor Surge Protection General NEPSI's MSP™ (Motor Surge Protector) is de- signed to protect medium voltage motors and gen- erators from voltage surges due to lightning and switching events. The MSP™ accomplishes this task better than any other product by decreasing the slope and crest of impending voltage surges to safe levels. Application of the MSP™ is guaranteed to reduce the likelihood of motor failures, resulting in less down-time and higher productivity. Figure 1 NEPSI's Medium Voltage Motor Surge Protection equip- ment protects motor insulation from power system transi- ents. Product Scope Reduced medium voltage motor and generator failures from voltage surges due to lightning, faults, and switching events. Units can be custom designed for direct mounting to generators, mo- tor, and compressor housing. Units can be supplied with over- current and differential protection current transformers. Reduced downtime and material waste from motor failure. Simple to install and requires no maintenance. MSP's are custom designed for many OEM’s utilizing medium volt- age motors and generators. Figure 2 Principle operation of the MSP™ is to decrease the crest voltage and rate of rise of the impending surges. High rates of rise damage end turns while high crest voltages damage winding to core insulation. Both of these types of damaging surges are mitigated with NEPSI's MSP™. P a g e | 1 Bulletin: 700-00 Rev. Date: 9/25/2015 Northeast Power Systems, Inc.
    [Show full text]
  • 5 Causes of Power Surges and How to Protect Your Property
    5 Causes of Power Surges and How to Protect Your Property Power surges happen whenever the wiring in your home or office experiences brief jolts of high electrical voltage. Power surges can be minor or severe. Even appliances or electronics that are turned off can flicker or buzz during a power surge, making it seem as though Casper is paying you a visit. Far from harmless though, power surges can damage your electrical outlets, fry your appliances and electronics and start dangerous electrical fires. Being cognizant and proactive against the causes of power surges can potentially save your electronics and more importantly, your life. Here are five serious causes of power surges and what you can do to protect your home or business. 1. Overloaded Outlets or Circuits Survey the outlets under your desk, behind your television set, or anywhere else you have a tangled web of wires. Plugging in too many appliances or electronics in the same socket can lead to power surges and electrical fires. If you are experiencing power surges, have an electrician check to see if all of the outlets in a room might be operating on the same circuit. If so, overloading one outlet might not be the problem. The circuit itself may be overloaded trying to power too many appliances in the same room. 2. Damaged or Exposed Wiring Pesky little critters such as mice or squirrels can chew on the wiring inside the walls of your house or building causing the wiring to fail. Damaged or exposed wires can cause power surges because the electricity flowing through them is not being directed or handled in the way it normally should.
    [Show full text]
  • Open Forum on Surge Protection Application Editor: Frariqois D
    Open Forum on Surge Protection Application Editor: FrariQois D. Martzloff U.S. DEPARTMENT OF COMMERCE National Institute of Standards and Technology Bectronics and Bectrical Engineering Laboratory Bectrldty Division Gaithersburg, MD 20899 Co-sponsored by: Computer Business Equipment Manufacturers Association Bectric Power Research Institute IEEE Standards Coordinating Committee 22 on Power Quality IEEE Surge-Protective Devices Committee ILS. DEPARTMENT OF COMMERCE Robert A. Mcebacher, Smcntmy NATIONAL msrnUTl OF STANDARDS AND ISCHNOLOOY JolH ¥L LyoM, dC— Diraetor 100 .U56 NIST /M657 1991 NISTIR 4657 Proceedings Open Forum on Surge Protection Appiication Editor: Francois D. Martzloff U.S. DEPARTMENT OF COMMERCE National Institute of Standards and Technology Electronics and Electrical Engineering Laboratory Electricity Division Gaithersburg, MD 20899 Co-sponsored by: Computer Business Equipment Manufacturers Association Electric Power Research Institute IEEE Standards Coordinating Committee 22 on Power Quality IEEE Surge-Protective Devices Committee August 1991 US. DEPARTMENT OF COMMERCE Robert A. Mosbacher, Secretary NATIONAL INSrnun OF STANDARDS AND TECHNOLOGY Jotai W. Lyoee, Diractor ii Table of Contents FOREWORD V THE SURGE ENVIRONMENT Power Quality Comparison - 1979 vs. 1991 1 Douglas S. Dorr, National Power Laboratory Voltage Surge Generated by Static Converters 11 Suang Khuwatsamrit, Reliance Electric Company On the Propagation of Old and New Surges 19 Francois D. Martzloff, National Institute of Standards and Technology THE PERFORMANCE OF SURGE-PROTECTIVE DEVICES Transient Voltage Surge Suppressor Specifications: Realistic Performance or Smoke and l^rrors? 27 O. Melville Clark, General Semiconductors Industries, Inc. Time Response of TVSS Devices 33 Hans j. Steinhoff, Joslyn Performance of MOV Suppressors in Low-Voltage AC Circuits 43 Martin P. Corbett, Harris Semiconductor and Bernhard I.
    [Show full text]
  • What to Know About Surge Protectors
    NEW MEXICO MILITARY INSTITUTE 101 WEST COLLEGE BOULEVARD ROSWELL, NM 88201 What to Know About Surge Protectors General Information about Surge Protectors Most modern businesses and homes are supplied with 120/240 volt power systems. The normal voltage flow for 120 voltage will often range from 110-117 volts. Computers, printer, stereo equipment and TV sets have internal circuits sensitive to voltage fluctuations and are often protected by surge protectors. Heavy draw appliances such as air conditioners, dryers, and electric stoves generally have no need to be protected by surge protectors. Surge Protectors are designed to trap the voltage that exceeds those limits. Excessive voltage occurs due to power spikes. When these spikes occur for a sufficient duration, this activates the trapping device, a Metal Oxide Varistor (MOV), located in the surge protector. The MOV is the heart of surge suppressors. The role of the MOV is to divert surge current. However, MOVs wear out with use. As more surges are diverted, the MOVs life span shortens, and failure becomes imminent. There are no forewarning or visual indications given – just failure. And while failing, they can reach very high temperatures, and actually start fires. Most surge protectors will continue to function as a power strip, even though the surge trap mechanism may have been destroyed by the power spike. This presents two possible dangers: If another power surge should occur, it can damage the equipment or appliances that are plugged into this surge protector. If sufficient voltage passes through the surge protector due to a second power spike, a resistant short may have been formed, allowing heating to occur and a fire to ignite.
    [Show full text]