Heat Transfer in Refrigerator Condensers and Evaporators

Total Page:16

File Type:pdf, Size:1020Kb

Heat Transfer in Refrigerator Condensers and Evaporators ,.' Heat Transfer in Refrigerator Condensers and Evaporators D. M. Admiraal and C. W. Bullard ACRCTR-48 August 1993 For additional information: Air Conditioning and Refrigeration Center University of Illinois Mechanical & Industrial Engineering Dept. 1206 West Green Street Urbana, IL 61801 Prepared as part ofACRC Project 12 Analysis ofRefrigerator-Freezer Systems (217) 333-3115 C. W. Bullard, Principal Investigator The Air Conditioning and Refrigeration Center was founded in 1988 with a grant from the estate of Richard W. Kritzer, the founder of Peerless of America Inc. A State of Illinois Technology Challenge Grant helped build the laboratory facilities. The ACRC receives continuing support from the Richard W. Kritzer Endowment and the National Science Foundation. Thefollowing organizations have also become sponsors of the Center. Acustar Division of Chrysler Allied-Signal, Inc. Amana Refrigeration, Inc. Brazeway, Inc. Carrier Corporation Caterpillar, Inc. E. I. du Pont de Nemours & Co. Electric Power Research Institute Ford Motor Company Frigidaire Company General Electric Company Harrison Division of GM ICI Americas, Inc. Modine Manufacturing Co. Peerless of America, Inc. Environmental Protection Agency U. S. Army CERL Whirlpool Corporation For additional information: Air Conditioning & Refrigeration Center Mechanical & Industrial Engineering Dept. University ofIllinois 1206 West Green Street Urbana IL 61801 2173333115 Table of Contents Page List of Tables ............................................................................................................................. v List of Figures ........................................................................................................................... vi Nomenclature .......................................................................................................................... vii Chapter 1. Introduction ........................................................................................................................ 1 1.1 Purpose ......................................................................................................................... 1 1.2 Development of the variable conductance model ..................................................... 2 1.3 Heat transfer correlations .......................................................................................... 3 1.3.1 Two-phase correlations .................................................................................. 3 1.3.2 Single-phase correlations ............................................................................... 6 2. Evaporator Model ............................................................................................................ 9 2.1 The two zone model ..................................................................................................... 9 2.2 The one zone model ................................................................................................... 16 2.3 Comparison with constant conductance models .................................................... 18 2.4 Summary .................................................................................................................... 19 3. Condenser Model ............................................................................................................ 20 3.1 Air-side complexities ................................................................................................. 20 3.2 Recirculation fraction ............................................................................................... 21 3.3 Volumetric air flow rate and leak fraction ............................................................. 23 3.4 Condenser inlet air temperature ............................................................................. 23 3.5 Governing equations ................................................................................................. 26 3.6 Summary .................................................................................................................... 31 4. Conclusions and Suggestions for Future Research ............................................ 33 4.1 Conclusions ................................................................................................................ 33 4.2 Suggestions for future research ............................................................................... 35 References ................................................................................................................................. 37 Appendix A. Objective Functions for Parameter Estimation ................................................... 38 B. Evaporator and Condenser Geometric Complexities ........................................ 42 B.l Evaporator ................................................................................................................ 42 B.2 Condenser .................................................................................................................. 43 C. Split Fraction and Volumetric Air Flow Rate in the Evaporator ................. 45 D. Possible Improvements In Condenser Performance .......................................... 49 D.l Improving air flow ................................................................................................... 49 D.2 Eliminating recirculation ......................................................................................... 50 111 E. Calculation of Refrigerant Mass Flow Rate .......................................................... 52 F. Comparison of Measured and Calculated Data .................................................. 56 IV List of Tables ThWe ~~ 2.1 Results of evaporator model ............................................................................................. 14 2.2 Calculation of air split fraction and volumetric flow rate ................................................. 15 2.3 Two-zone constant conductance results ............................................................................ 18 3.1 Recirculation fraction ........................................................................................................ 22 3.2 Summary of condenser results .......................................................................................... 29 C.1 Independent calculation of air split fraction and volume flow rate .................................. 47 C.2 Simultaneous calculation of air split fraction and volume flow rate ................................ 48 v List of Figures mpre ~~ 1.1 Comparison of BoPierre and ChatolWattelet heat transfer coefficients ....................... 5 2.1 Evaporator heat exchanger geometry ............................................................................ 9 2.2 Comparison of calculated and measured evaporator loads for data set I .................... 12 2.3 Comparison of calculated and measured evaporator loads for data set 11 ................... 12 2.4 Heat load confidence interval vs. volumetric air flow rate ......................................... 13 2.5 Air flow through refrigerator compartment ................................................................ 15 2.6 Comparison of ChatolW attelet and BoPierre parameter estimation ........................... 17 3.1 Condenser heat exchanger geometry .......................................................................... 20 3.2 Comparison of calculated and measured values of grille inlet temperature ............... 22 3.3 Front view of condenser air inlet ................................................................................ 24 3.4 Condenser inlet air temperature distribution ............................................................... 24 3.5 Average air inlet temperatures .................................................................................... 25 3.6 Comparison of calculated and measured condenser loads .......................................... 30 4.1 Contributions to overall heat transfer resistance ......................................................... 35 C.1 Air mixture control volume ......................................................................................... 45 E.1 Data set I refrigerant mass flow measurements .......................................................... 53 E.2 Data set II refrigerant mass flow measurements ......................................................... 54 F.1 Evaporator exit temperature comparison, data set 1.. .................................................. 56 F.2 Evaporator exit temperature comparison, data set II .................................................. 56 F.3 Single-zone evaporator load comparison, data set II .................................................. 57 F.4 Condenser load comparison, Reeves (1992) ............................................................... 57 F.5 Condenser load comparison, data set I.. ...................................................................... 58 F.6 Condenser load comparison, data set II ...................................................................... 58 vi Nomenclature A area [ft2] C heat capacity (rbcp) [Btu/(h·oP)] cp specific heat [Btu/(lbm·op)] D internal tube diameter eft] f fraction G mass flux [lbm/(h·ft2)] g acceleration of gravity [ft/s2] h heat transfer coefficient [Btu/(h·ft2.oP)] hfg heat of vaporization [Btu/lbm] J mechanical equivalent of heat [778.3 ft·lbf/Btu] k thermal conductivity [Btu/(h·ft·oP)] L length of tube eft] Ih mass flow rate [lbm/h] Q
Recommended publications
  • Heat Transfer Model of a Rotary Compressor S
    Purdue University Purdue e-Pubs International Compressor Engineering Conference School of Mechanical Engineering 1992 Heat Transfer Model of a Rotary Compressor S. K. Padhy General Electric Company Follow this and additional works at: https://docs.lib.purdue.edu/icec Padhy, S. K., "Heat Transfer Model of a Rotary Compressor" (1992). International Compressor Engineering Conference. Paper 935. https://docs.lib.purdue.edu/icec/935 This document has been made available through Purdue e-Pubs, a service of the Purdue University Libraries. Please contact [email protected] for additional information. Complete proceedings may be acquired in print and on CD-ROM directly from the Ray W. Herrick Laboratories at https://engineering.purdue.edu/ Herrick/Events/orderlit.html HEAT TRANSFER MODEL OF A ROTARY COMPRESSOR Sisir K. Padhy General Electric C_ompany Appliance Park 5-2North, Louisville, KY 40225 ABSTRACT Energy improvements for a rotary compressor can be achieved in several ways such as: reduction of various electrical and mechanical losses, reduction of gas leakage, better lubrication, better surface cooling, reduction of suction gas heating and by improving other parameters. To have a ' better understanding analytical/numerical analysis is needed. Although various mechanical models are presented to understand the mechanical losses, dynamics, thermodynamics etc.; little work has been done to understand the compressor from a heat uansfer stand point In this paper a lumped heat transfer model for the rotary compressor is described. Various heat sources and heat sinks are analyzed and the temperature profile of the compressor is generated. A good agreement is found between theoretical and experimental results. NOMENCLATURE D, inner diameter D.
    [Show full text]
  • Why Does the Wisconsin Boiler and Pressure Vessel Code, 636 41
    Why does the Wisconsin Boiler and Pressure Vessel Code, SPS 341, regulate air compressors? By Industry Services Division Boiler and Pressure Vessels Program Almost everyone forms a definite picture in their mind when they hear the term “air compressor.” They probably think of a steel tank of some shape and dimension, with an electric motor, and an air pump mounted on top of the tank. To better understand the requirements of the Wisconsin Boiler Code, SPS 341, pertaining to air compressors, we need to have some common terminology. If a person wanted to purchase an “air compressor” at a hardware or home supply store, they would certainly be offered the equipment described above, consisting of three separate mechanical devices; the motor, the pump, and the storage tank. First, there is an electric motor, used to provide power to the device that pumps air to high pressure. This pumping device is the only part of the unit that is properly called an "air compressor." The compressor delivers high-pressure air to the third and final part of the mechanical assembly, the air storage tank; commonly called a pressure vessel. Because the pressure vessel receives pressurized air, this is the only part of the device described above that is regulated SPS 341. SPS 341 regulates pressure vessels when the pressure vessel's volume capacity is 90 gallons (12 cubic feet) or larger, and the air pressure is 15 pounds per square inch or higher. A typical pressure vessel of this size would be 24 inches in diameter and 48 inches long. In industrial settings, it is common practice to mount very large air compressors in a separate location from the pressure vessels.
    [Show full text]
  • Performance Comparison Between an Absorption-Compression Hybrid Refrigeration System and a Double-Effect Absorption Refrigeration Sys-Tem
    Available online at www.sciencedirect.com ScienceDirect Available online at www.sciencedirect.com Procedia Engineering 00 (2017) 000–000 ScienceDirect www.elsevier.com/locate/procedia Procedia Engineering 205 (2017) 241–247 10th International Symposium on Heating, Ventilation and Air Conditioning, ISHVAC2017, 19- 22 October 2017, Jinan, China Performance Comparison between an Absorption-compression Hybrid Refrigeration System and a Double-effect Absorption Refrigeration Sys-tem Jian Wang, Xianting Li, Baolong Wang, Wei Wu, Pengyuan Song, Wenxing Shi* Beijing Key Laboratory of Indoor Air Quality Evaluation and Control, Department of Building Science, Tsinghua University, Haidian District, Beijing 100084, China Abstract Conventional absorption refrigeration systems (ARSs), which are mainly driven by heat, have a competitive primary energy efficiency (PEE) compared with chillers driven by electricity. In the typical ARS, a large quantity of high-temperature heat is supplied into the generator, while a substantial amount of low-temperature heat is rejected to the environment from the condenser, it’s a huge waste. In order to decrease the input heat for generator and enhance the performance of conventional ARS, a kind of absorption-compression hybrid refrigeration system recovering condensation heat for generation (RCHG-ARS) was ever proposed. In the present study, the models of both RCHG-ARS and double-effect absorption refrigeration system (DEARS) are established, and the effects of different parameters on them are simulated and compared with each other. As a conclusion, the PEE of RCHG-ARS can be 29.0% higher than that of DEARS, and RCHG-ARS has a wider working conditions than DEARS due to the existence of the compressor.
    [Show full text]
  • Vapour Absorption Refrigeration Systems Based on Ammonia- Water Pair
    Lesson 17 Vapour Absorption Refrigeration Systems Based On Ammonia- Water Pair Version 1 ME, IIT Kharagpur 1 The specific objectives of this lesson are to: 1. Introduce ammonia-water systems (Section 17.1) 2. Explain the working principle of vapour absorption refrigeration systems based on ammonia-water (Section 17.2) 3. Explain the principle of rectification column and dephlegmator (Section 17.3) 4. Present the steady flow analysis of ammonia-water systems (Section 17.4) 5. Discuss the working principle of pumpless absorption refrigeration systems (Section 17.5) 6. Discuss briefly solar energy based sorption refrigeration systems (Section 17.6) 7. Compare compression systems with absorption systems (Section 17.7) At the end of the lecture, the student should be able to: 1. Draw the schematic of a ammonia-water based vapour absorption refrigeration system and explain its working principle 2. Explain the principle of rectification column and dephlegmator using temperature-concentration diagrams 3. Carry out steady flow analysis of absorption systems based on ammonia- water 4. Explain the working principle of Platen-Munter’s system 5. List solar energy driven sorption refrigeration systems 6. Compare vapour compression systems with vapour absorption systems 17.1. Introduction Vapour absorption refrigeration system based on ammonia-water is one of the oldest refrigeration systems. As mentioned earlier, in this system ammonia is used as refrigerant and water is used as absorbent. Since the boiling point temperature difference between ammonia and water is not very high, both ammonia and water are generated from the solution in the generator. Since presence of large amount of water in refrigerant circuit is detrimental to system performance, rectification of the generated vapour is carried out using a rectification column and a dephlegmator.
    [Show full text]
  • Chapter 8 and 9 – Energy Balances
    CBE2124, Levicky Chapter 8 and 9 – Energy Balances Reference States . Recall that enthalpy and internal energy are always defined relative to a reference state (Chapter 7). When solving energy balance problems, it is therefore necessary to define a reference state for each chemical species in the energy balance (the reference state may be predefined if a tabulated set of data is used such as the steam tables). Example . Suppose water vapor at 300 oC and 5 bar is chosen as a reference state at which Hˆ is defined to be zero. Relative to this state, what is the specific enthalpy of liquid water at 75 oC and 1 bar? What is the specific internal energy of liquid water at 75 oC and 1 bar? (Use Table B. 7). Calculating changes in enthalpy and internal energy. Hˆ and Uˆ are state functions , meaning that their values only depend on the state of the system, and not on the path taken to arrive at that state. IMPORTANT : Given a state A (as characterized by a set of variables such as pressure, temperature, composition) and a state B, the change in enthalpy of the system as it passes from A to B can be calculated along any path that leads from A to B, whether or not the path is the one actually followed. Example . 18 g of liquid water freezes to 18 g of ice while the temperature is held constant at 0 oC and the pressure is held constant at 1 atm. The enthalpy change for the process is measured to be ∆ Hˆ = - 6.01 kJ.
    [Show full text]
  • Ammonia As a Refrigerant
    1791 Tullie Circle, NE. Atlanta, Georgia 30329-2305, USA www.ashrae.org ASHRAE Position Document on Ammonia as a Refrigerant Approved by ASHRAE Board of Directors February 1, 2017 Expires February 1, 2020 ASHRAE S H A P I N G T O M O R R O W ’ S B U I L T E N V I R O N M E N T T O D A Y © 2017 ASHRAE (www.ashrae.org). For personal use only. Additional reproduction, distribution, or transmission in either print or digital form is not permitted without ASHRAE’s prior written permission. COMMITTEE ROSTER The ASHRAE Position Document on “Ammonia as a Refrigerant” was developed by the Society’s Refrigeration Committee. Position Document Committee formed on January 8, 2016 with Dave Rule as its chair. Dave Rule, Chair Georgi Kazachki IIAR Dayton Phoenix Group Alexandria, VA, USA Dayton, OH, USA Ray Cole Richard Royal Axiom Engineers, Inc. Walmart Monterey, CA, USA Bentonville, Arkansas, USA Dan Dettmers Greg Scrivener IRC, University of Wisconsin Cold Dynamics Madison, WI, USA Meadow Lake, SK, Canada Derek Hamilton Azane Inc. San Francisco, CA, USA Other contributors: M. Kent Anderson Caleb Nelson Consultant Azane, Inc. Bethesda, MD, USA Missoula, MT, USA Cognizant Committees The chairperson of Refrigerant Committee also served as ex-officio members: Karim Amrane REF Committee AHRI Bethesda, MD, USA i © 2017 ASHRAE (www.ashrae.org). For personal use only. Additional reproduction, distribution, or transmission in either print or digital form is not permitted without ASHRAE’s prior written permission. HISTORY of REVISION / REAFFIRMATION / WITHDRAWAL
    [Show full text]
  • A Comparative Energy and Economic Analysis Between a Low Enthalpy Geothermal Design and Gas, Diesel and Biomass Technologies for a HVAC System Installed in an Office Building
    energies Article A Comparative Energy and Economic Analysis between a Low Enthalpy Geothermal Design and Gas, Diesel and Biomass Technologies for a HVAC System Installed in an Office Building José Ignacio Villarino 1, Alberto Villarino 1,* , I. de Arteaga 2 , Roberto Quinteros 2 and Alejandro Alañón 1 1 Department of Construction and Agronomy, Construction Engineering Area, High Polytechnic School of Ávila, University of Salamanca, Hornos Caleros, 50, 05003 Ávila, Spain; [email protected] (J.I.V.); [email protected] (A.A.) 2 Facultad de Ingeniería, Escuela de Ingeniería Mecánica, Pontificia Universidad Católica de Valparaíso, Av. Los Carrera 01567, Quilpué 2430000, Chile; [email protected] (I.d.A.); [email protected] (R.Q.) * Correspondence: [email protected]; Tel.: +34-920-353-500; Fax: +34-920-353-501 Received: 3 January 2019; Accepted: 25 February 2019; Published: 6 March 2019 Abstract: This paper presents an analysis of economic and energy between a ground-coupled heat pump system and other available technologies, such as natural gas, biomass, and diesel, providing heating, ventilation, and air conditioning to an office building. All the proposed systems are capable of reaching temperatures of 22 ◦C/25 ◦C in heating and cooling modes. EnergyPlus software was used to develop a simulation model and carry out the validation process. The first objective of the paper is the validation of the numerical model developed in EnergyPlus with the experimental results collected from the monitored building to evaluate the system in other operating conditions and to compare it with other available technologies. The second aim of the study is the assessment of the position of the low enthalpy geothermal system proposed versus the rest of the systems, from energy, economic, and environmental aspects.
    [Show full text]
  • Heat Transfer in Flat-Plate Solar Air-Heating Collectors
    Advanced Computational Methods in Heat Transfer VI, C.A. Brebbia & B. Sunden (Editors) © 2000 WIT Press, www.witpress.com, ISBN 1-85312-818-X Heat transfer in flat-plate solar air-heating collectors Y. Nassar & E. Sergievsky Abstract All energy systems involve processes of heat transfer. Solar energy is obviously a field where heat transfer plays crucial role. Solar collector represents a heat exchanger, in which receive solar radiation, transform it to heat and transfer this heat to the working fluid in the collector's channel The radiation and convection heat transfer processes inside the collectors depend on the temperatures of the collector components and on the hydrodynamic characteristics of the working fluid. Economically, solar energy systems are at best marginal in most cases. In order to realize the potential of solar energy, a combination of better design and performance and of environmental considerations would be necessary. This paper describes the thermal behavior of several types of flat-plate solar air-heating collectors. 1 Introduction Nowadays the problem of utilization of solar energy is very important. By economic estimations, for the regions of annual incident solar radiation not less than 4300 MJ/m^ pear a year (i.e. lower 60 latitude), it will be possible to cover - by using an effective flat-plate solar collector- up to 25% energy demand in hot water supply systems and up to 75% in space heating systems. Solar collector is the main element of any thermal solar system. Besides of large number of scientific publications, on the problem of solar energy utilization, for today there is no common satisfactory technique to evaluate the thermal behaviors of solar systems, especially the local characteristics of the solar collector.
    [Show full text]
  • The Potential and Challenges of Solar Boosted Heat Pumps for Domestic Hot Water Heating
    Solar Calorimetry Laboratory The Potential and Challenges of Solar Boosted Heat Pumps for Domestic Hot Water Heating Stephen Harrison Ph.D., P. Eng., Solar Calorimetry Laboratory, Dept. of Mechanical and Materials Engineering, Queen’s University, Kingston, ON, Canada Solar Calorimetry Laboratory Background • As many groups try to improve energy efficiency in residences, hot water heating loads remain a significant energy demand. • Even in heating-dominated climates, energy use for hot water production represents ~ 20% of a building’s annual energy consumption. • Many jurisdictions are imposing, or considering regulations, specifying higher hot water heating efficiencies. – New EU requirements will effectively require the use of either heat pumps or solar heating systems for domestic hot water production – In the USA, for storage systems above (i.e., 208 L) capacity, similar regulations currently apply Canadian residential sector energy consumption (Source: CBEEDAC) Solar Calorimetry Laboratory Solar and HP water heaters • Both solar-thermal and air-source heat pumps can achieve efficiencies above 100% based on their primary energy consumption. • Both technologies are well developed, but have limitations in many climatic regions. • In particular, colder ambient temperatures lower the performance of these units making them less attractive than alternative, more conventional, water heating approaches. Solar Collector • Another drawback relates to the requirement to have an auxiliary heat source to supplement the solar or heat pump unit,
    [Show full text]
  • (Vocs) in Asian and North American Pollution Plumes During INTEX-B: Identification of Specific Chinese Air Mass Tracers
    Atmos. Chem. Phys., 9, 5371–5388, 2009 www.atmos-chem-phys.net/9/5371/2009/ Atmospheric © Author(s) 2009. This work is distributed under Chemistry the Creative Commons Attribution 3.0 License. and Physics Characterization of volatile organic compounds (VOCs) in Asian and north American pollution plumes during INTEX-B: identification of specific Chinese air mass tracers B. Barletta1, S. Meinardi1, I. J. Simpson1, E. L. Atlas2, A. J. Beyersdorf3, A. K. Baker4, N. J. Blake1, M. Yang1, J. R. Midyett1, B. J. Novak1, R. J. McKeachie1, H. E. Fuelberg5, G. W. Sachse3, M. A. Avery3, T. Campos6, A. J. Weinheimer6, F. S. Rowland1, and D. R. Blake1 1University of California, Irvine, 531 Rowland Hall, Irvine 92697 CA, USA 2University of Miami, RSMAS/MAC, 4600 Rickenbacker Causeway, Miami, 33149 FL, USA 3NASA Langley Research Center, Hampton, 23681 VA, USA 4Max Plank Institute, Atmospheric Chemistry Dept., Johannes-Joachim-Becherweg 27, 55128 Mainz, Germany 5Florida State University, Department of Meteorology, Tallahassee Florida 32306-4520, USA 6NCAR, 1850 Table Mesa Drive, Boulder, 80305 CO, USA Received: 9 March 2009 – Published in Atmos. Chem. Phys. Discuss.: 24 March 2009 Revised: 16 June 2009 – Accepted: 17 June 2009 – Published: 30 July 2009 Abstract. We present results from the Intercontinental 1 Introduction Chemical Transport Experiment – Phase B (INTEX-B) air- craft mission conducted in spring 2006. By analyzing the The Intercontinental Chemical Transport Experiment – mixing ratios of volatile organic compounds (VOCs) mea- Phase B (INTEX-B) aircraft experiment was conducted in sured during the second part of the field campaign, to- the spring of 2006. Its broad objective was to understand gether with kinematic back trajectories, we were able to the behavior of trace gases and aerosols on transcontinental identify five plumes originating from China, four plumes and intercontinental scales, and their impact on air quality from other Asian regions, and three plumes from the United and climate (an overview of the INTEX-B campaign can be States.
    [Show full text]
  • Clean Coil Program
    TM CLEAN COIL PROGRAM There are many good reasons to clean coils! And, here is what the Nu-Calgon Clean Coil & IAQ Assurance Program can do for you... Gain significant savings on energy costs. Maintain peak operating efficiency. Enhance the cooling system’s reliability and service life. Prevent costly breakdowns. Improve Indoor Air Quality (IAQ). Backed by Nu-Calgon, the leader in HVAC and Refrigeration maintenance chemicals for more than 60 years. www.nucalgon.com l www.coilcleaning.com l www.coilprotection.com NU-CALGON CLEAN COIL & IAQ ASSURANCE PROGRAM FOR AIR CONDITIONING, REFRIGERATION SYSTEMS Over the last 50 years, Nu-Calgon has developed products that have proven themselves in the successful cleaning and protection of air conditioning and refrigeration equipment. Now, these products have been further developed into a program that will keep this equipment operating efficiently and effectively, thereby cutting electric bills, increasing the equipment’s service life, and improving the comfort and Indoor Air Quality of the building or home. An air conditioning or refrigeration system has two “finned” coils, and typically they are constructed of copper tube and aluminum fins. The evaporator coil is the indoor coil, usually referred to as the “A” coil in residential systems. It could be described as “cold” as it provides indoor cooling by absorbing the heat as a fan passes the building air over it. The condenser coil or outdoor coil is the coil that is “warm” as it rejects the heat as a fan blows outdoor air across it. These coils are sized to match the Btu cooling load or requirement of the home or building, and they are engineered for maximum heat transfer .
    [Show full text]
  • Compact Heat Exchangers for Mobile Co2 Systems
    COMPACT HEAT EXCHANGERS FOR MOBILE CO2 SYSTEMS A. Hafner SINTEF Energy Research Refrigeration and Air Conditioning Trondheim (Norway) ABSTRACT The natural refrigerant carbon dioxide (CO2) with all its advantages offers new possibilities of efficient heating and cooling at different climates. In reversible air conditioning systems the capacity and efficiency in cooling mode is seen to be most important. The efficiency of the reversible interior heat exchanger depends on the design of the heat exchanger. Efficiency reduction is among other factors caused by refrigerant- side pressure drop, heat conduction, refrigerant- and air maldistribution. Uniform air temperatures at the outlet of the heat exchanger are an important aspect regarding comfort and control of the mobile HVAC system. A prototype CO2 system with a separator, refrigerant pump and a single pass heat exchanger was tested under varies conditions. The tests were performed at low compressor revolution speed i.e. idle conditions. Compared with a baseline heat exchanger of equal size, the use of an external operated pump to circulate the refrigerant through the heat exchanger, increased the cooling capacity at equal pressure levels by up to 14 %. At equal cooling capacities the COP increased by up to 23 %. Airside temperature distribution was more uniform with this way of operating the system. 1 INTRODUCTION Several authors for example Hrnjak et al 2002, Nekså et al. 2001 describe CO2 systems where flash gas was bypassed the evaporator and thereafter reunified with the leaving gas of the evaporator. With such a system concept only liquid refrigerant enters the evaporator which has an positive effect on distribution of the refrigerant into 20000 the microchannels.
    [Show full text]