Makerspace Sewing Machine (Janome) One Sheet: Loading a Bobbin 1

Total Page：16

File Type：pdf, Size：1020Kb

Makerspace Sewing Machine (Janome) One Sheet: Loading A Bobbin 1. Lift up the spool pin.(located on the top of the 2. Select an unused bobbin. machine) Place the spool of thread on the spool pin with the thread coming off the spool. 3. Pass the thread from the spool and pass the 4. Pass the thread through the hole in the bobbin thread through the thread guide. Draw the thread from the inside to the outside. Put the bobbin on the around and under the bobbin winding tension disk. bobbin winder spindle. Push the bobbin to the right to lock the bobbin in place. 5. Hold the free end of the thread in your hand and press the bobbin winding button located on the front of the machine. Press the bobbin winding button again to stop the bobbin once it has wound several layers and cut off the protruding string. Press again to finish winding the bobbin. The winder will automatically shut off when finished. Makerspace Sewing Machine (Janome) One Sheet: Loading A Bobbin 9. Now you may remove the bobbin and cut the 10. Place the bobbin in the bobbin holder with the connecting thread. This bobbin is now ready to be thread running off counterclockwise. put into bobbin holder. 11. Guide the thread into the front notch on the 12. Draw thread to the left sliding it between the bobbin holder (A). tension spring blades. 13. Continue to draw the thread lightly until the 14. Pull out about 4” of thread to the rear. Re-attach thread slips into the side notch (B). the hook cover plate. Now you may thread the machine. Refer to using the sewing machine. Modified with permission from think[box] at Case Western Reserve University. This document has been prepared by, or incorporates material produced by, think[box]at Case Western Reserve University. By using this material, in whole or in part, modified or unmodified, you agree to release and forever discharge Case Western Reserve University from all claims, costs, liabilities, and judgements including attorney’s fees and court costs, arising out of your use of this document. http://thinkbox.case.edu .

Copy Link

Recommended publications

Bobbinwork Basics by Jill Danklefsen
SPECIAL CLASSROOM EDITION BOBBINWORK BASICS BY JILL DANKLEFSEN obbinwork is a technique that places heavy decorative 4. The type of stitch chosen as well as the type of “bobbin yarn” Bthreads on the surface of the fabric, sewn as machine-fed selected will dictate how loose the tension needs to be adjusted decorative stitches or as freemotion stitches. Typically, these on the bobbin case. threads, yarns, and cords are too large to fit through the eye of the sewing machine needle. So, in order to achieve a “stitched 5. Remember the rule of tension adjustment --“Righty, Tighty -- look”, you sew with the heavy decorative thread wound onto a Lefty, Loosey” bobbin and placed in the bobbin case of the machine. 6. Use a “construction quality” thread on the “topside” of your machine, as the needle tension will usually be increased. Think of the top thread as literally pulling the “bobbin yarn” into place to form the stitch pattern. 7. Bobbins can be wound by hand or by machine. Whenever possible, wind the bobbin using the bobbin winder mechanism on the machine. This will properly tension the “bobbin yarn” for a better stitch quality. 8. Bobbinwork can be sewn with the Feed dogs up or down. If stitching freemotion, a layer of additional stabilizer or the use of a machine embroidery hoop may be necessary. 9. Select the proper presser foot for the particular bobbinwork YARNS AND THREADS SUITABLE FOR BOBBINWORK technique being sewn. When working with the heavier “bobbin yarns”, the stitches produced will be thicker. Consider selecting • Yarns (thinner types, often a foot with a large indentation underneath it, such as Foot used for knitting machines) #20/#20C.This foot will ride over the stitching much better.
[Show full text]
Powerhouse Museum Lace Collection: Glossary of Terms Used in the Documentation – Blue Files and Collection Notebooks
Book Appendix Glossary 12-02 Powerhouse Museum Lace Collection: Glossary of terms used in the documentation – Blue files and collection notebooks. Rosemary Shepherd: 1983 to 2003 The following references were used in the documentation. For needle laces: Therese de Dillmont, The Complete Encyclopaedia of Needlework, Running Press reprint, Philadelphia, 1971 For bobbin laces: Bridget M Cook and Geraldine Stott, The Book of Bobbin Lace Stitches, A H & A W Reed, Sydney, 1980 The principal historical reference: Santina Levey, Lace a History, Victoria and Albert Museum and W H Maney, Leeds, 1983 In compiling the glossary reference was also made to Alexandra Stillwell’s Illustrated dictionary of lacemaking, Cassell, London 1996 General lace and lacemaking terms A border, flounce or edging is a length of lace with one shaped edge (headside) and one straight edge (footside). The headside shaping may be as insignificant as a straight or undulating line of picots, or as pronounced as deep ‘van Dyke’ scallops. ‘Border’ is used for laces to 100mm and ‘flounce’ for laces wider than 100 mm and these are the terms used in the documentation of the Powerhouse collection. The term ‘lace edging’ is often used elsewhere instead of border, for very narrow laces. An insertion is usually a length of lace with two straight edges (footsides) which are stitched directly onto the mounting fabric, the fabric then being cut away behind the lace. Ocasionally lace insertions are shaped (for example, square or triangular motifs for use on household linen) in which case they are entirely enclosed by a footside. See also ‘panel’ and ‘engrelure’ A lace panel is usually has finished edges, enclosing a specially designed motif.
[Show full text]
Needle Arts 3 11628.Qxd
NEEDLE ARTS 3 PACK 11628 • 20 DESIGNS NX670 Flowered Hat Pins NX671 Handmade With Love By NX672 Sewing Bobbin Machine NX673 Rotary Cutter 2.11 X 3.89 in. 3.10 X 2.80 in. 2.49 X 2.50 in. 3.89 X 1.74 in. 53.59 X 98.81 mm 78.74 X 71.12 mm 63.25 X 63.50 mm 98.81 X 44.20 mm 4,587 St. 11,536 St. 10,818 St. 10,690 St. NX674 Dressmaker’s Shears NX675 Thread NX676 Sewing Border NX677 Tracing Wheel 3.89 X 1.88 in. 2.88 X 3.89 in. 5.00 X 2.19 in. 3.46 X 1.74 in. 98.81 X 47.75 mm 73.15 X 98.81 mm 127.00 X 55.63 mm 87.88 X 44.20 mm 7,892 St. 15,420 St. 16,465 St. 3,282 St. NX678 Sewing Angel NX679 Tomato Pincushion NX680 Measuring Tape NX681 Sewing Kit 3.76 X 3.21 in. 3.59 X 3.76 in. 3.69 X 1.78 in. 3.89 X 3.67 in. 95.50 X 81.53 mm 91.19 X 95.50 mm 93.73 X 45.21 mm 98.81 X 93.22 mm 20,593 St. 16,556 St. 8,410 St. 22,777 St. NX682 Iron & Ironing Board NX683 Sewing Machine Needle NX684 Needle Thread NX685 Embroidery Scissors 3.79 X 1.40 in. 1.57 X 2.89 in. 1.57 X 3.10 in. 3.00 X 2.58 in.
[Show full text]
ONE-STEP BOBBIN REPLACEMENT FEATURES QUICK-SET TOP BOBBIN the Easy-To-View Window Tells You at a Glance When More Thread Is Need
ONE-STEP BOBBIN REPLACEMENT FEATURES QUICK-SET TOP BOBBIN The easy-to-view window tells you at a glance when more thread is needed in your bobbin. Simply drop in a full bobbin and the Quickset feature has you ready to sew immediately. F.A.S.T. BOBBIN WINDING SYSTEM Brother's use of the latest technology has made their sewing machines even easier to use. To wind the bobbin, just wind the thread around the bobbin a few times, pass it through the slit in the bobbin winder seat and press the START/STOP button. No need to cut off the excess thread or stop the sewing machine when the bobbin is full. START/STOPBUTTON The gentle sewing start lets you use the machine with confidence with or without the electronic foot control. EASY-TO-USE SPEED ADJUSTMENT The speed adjustment lever lets you smoothly adjust the operation speed from low speed and high speed. Enjoy the freedom of being able to adjust the sewing speed while you sew! F.A.S.T. NEEDLE-THREADING SYSTEM Fast and simple threading says it all! Saves time and your eyesight, by automatically feeding the thread through the needle's eye. STITCH LENGTH / WIDTH ADJUSTMENT Adjustments for stitch length; stitch width and variable needle position make sewing fine details fast and easy. Quilters will love the variable needle position for adjusting the seam allowance. 1-STEP AUTOMATIC BUTTONHOLER 1-Step "Auto-size" buttonholer creates a perfectly uniform buttonhole every time. Simply dial the stitch and follow the directions to sew all four sides of the buttonhole without moving a lever.
[Show full text]
Tips for Minimizing Embroidery Interruptions
TECHNICAL BULLETIN TIPS FOR MINIMIZING EMBROIDERY INTERRUPTIONS Sewing interruptions can be caused by many factors, however the most common causes include the following: • Needle Thread Breakage or Pull-out – not picking up at the beginning of a stitch pattern • Bobbin Thread Run-out or Thread Pick-Up – not picking up at the beginning of a stitch pattern • Improper Thread Trimming • Thread break detector stoppage In order to minimize interruptions during the stitching of complex embroidery patterns, the following vital elements must work together during the embroidery process. These vital elements include: • Proper Digitizing for the fabric and pattern being sewn • Proper Embroidery Machine Maintenance and Settings • Correct Backings and/or Toppings for the Application • Proper Needle Type and Size • Quality Embroidery Threads We will look at each of these elements and discuss potential causes for excessive sewing interruptions. A. INTERRUPTIONS DUE TO NEEDLE THREAD BREAK Digitizing Causes: • Improper cornering with too many stitches in the same location • Not using appropriate underlay stitches that help minimize flagging during the rest of the stitch pattern • Density properties too high within designs that layer many colors of thread • Not using Tie-In Stitches at beginning of thread changes • Not using Short Stitches at the end of a stitching cycle Digitizing Solutions: • Try to minimize the stitch density at any one point. TECHNICAL BULLETIN • Reduce density properties as you build up layers of embroidery • On lettering, use your “short-stitch” function • Use appropriate underlay stitches that help minimize flagging • Use slower speed “Tie-In” Stitches at beginning of thread changes • Use slower speed “Tie-Off” Stitches at the end of a stitching cycle.
[Show full text]
Instruction Manual for Sewing Machine
f2D /3a INSTRUCTION MANUAL FOR I SEWING MACHINE EL3-1© j WHITE’ _____________________________________ WHITE SEWING MACHINE COMPANY Record in space provided below the Serial No. and Model No. of this appliance. The Serial No. is located on Bed Plate. The Model No. is located on Rating Plate. Serial No. Model No. Retain these numbers for future reference. 21&22 CONTENTS Name of Parts 1 & 2 Accessories 3 Before sewing (Power supply and Sewing lamp) 4 Take out extension table, free arm sewing 5 Winding the bobbin 6 Removing bobbin case and bobbin 7 Inserting bobbin into bobbin case 7 Inserting bobbin case into shuttle race 8 Threading upper thread & Twin needle threadg. 9 Drawing up bobbin thread 10 Changing sewing directions 10 Control dial & Adjusting thread tension 11&12 Regulating the presser foot pressure 13 Drop feed 13 Changing needle 14 Fabric. Thread. Needle table 15 Sewing (pattern selector) and operation table 16 To start sewing 17 To finish seam 18 Straight stitch 19 Zigzag sewing 19 Overcasting 20 Stretch stitch 20 Blind stitch Button sewing 23 Binding 23 Zipper sewing 24 Button hole sewing 25 Hemming 26 Twin Needle 27 Embroidery 27 Quilter 28 Seam guide 28 Maintenance (Cle.ning and oiling) 29 Checking Performance Problems WHAT TO DO 30 NAME OF PARTS (FRONT VIEW) 1 Pattern selector dial 8 Sub-spool pins 2 Pressure regulator 9 Top cover 3 Take up lever 10 Zigzag width dial 4 Thread tension dial 1 1 Stitch length dial 5 Presser foot 12 Reverse button 6 Shuttle cover 13 Thread guide for upper 7 Extension table threading —1— (REAR VIEW) Bobbin winder spindle Bobbin winder stopper Upper thread guide Stop Motion knob Hand wheel Face cover Thumb screw Needle plate Presser foot lever —2— ACCESSOR I ES / Bobbin Felt Zigzag foot Button hole (On machine) foot Button foot Machine Oil / Zipper foot 0 Button hole cutter Screw driver Needle #11 #14 —3— BEFORE SEWING 1.
[Show full text]
Download MOD-100 Manual
Instruction Book IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic safety precautions should always be followed, including the following: This sewing machine is designed and manufactured for household use only. Read all instructions before using this sewing machine. DANGER— To reduce the risk of electric shock: 1. An appliance should never be left unattended when plugged in. Always unplug this sewing machine from the electric outlet immediately after using and before cleaning. WARNING— To reduce the risk of burns, fire, electric shock, or injury to persons: 1. Do not allow to be used as a toy. Close attention is necessary when this sewing machine is used by or near children. 2. Use this appliance only for its intended use as described in this owner’s manual. Use only attachments recommended by the manufacturer as contained in this owner’s manual. 3. Never operate this sewing machine if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or dropped into water. Return this sewing machine to the nearest authorized dealer or service center for examination, repair, electrical or mechanical adjustment. 4. Never operate the appliance with any air opening blocked. Keep ventilation openings of this sewing machine and foot controller free from accumulation of lint, dust and loose cloth. 5. Never drop or insert any object into any opening. 6. Do not use outdoors. 7. Do not operate where aerosol (spray) products are being used or where oxygen is being administered. 8. To disconnect, turn all controls to the off (“O”) position, then remove plug from outlet.
[Show full text]
Bobbin Lace Class Handout (PDF)
Beginning Bobbin Lace By Tim & Debbie Coyle Brief History It’s difficult to tell the early history of most fiber arts, as the fabrics are lost through reuse of the materials or deterioration. Bobbin lace is documented as far back as the 15th century in Italy. The technique spread quickly and widely after that. By the end of the 16th century Spain was producing colored silk laces as well as gold and silver laces. The Scandinavian counties and Germany were also very influential in furthering bobbin lace. Although lace is often thought of as adorning ecclesiastical fabrics and the garments of the wealthy and titled, peasants were numbered among the people making and wearing bobbin lace. In Eastern Europe they were responsible for keeping the technique alive, their laces were sophisticated and developed into very personal designs. Materials Pillow The pillow is the working platform for your lace. Pillows come in many shapes and sizes, and are made of many different materials, from straw or fabric scraps contained in a fabric covering, to different types of foam covered in fabric. What they all have in common is a firm but yielding texture that allows pins to go in easily and stay in place without wobbling. This kit contains a close cell foam block that works well to keep the pins in position. Rather than covering the foam with fabric, we have covered the top with the pricking pattern and instructions. You might want to buy some cotton quilting fabric, cut it to size, and pin it on to cover all sides of the foam.
[Show full text]
Instruction Manual INDICE SECTION 1
Instruction Manual INDICE SECTION 1. ESSENTIAL PARTS Name of Parts ................................................................................................................. 2 SECTION 2. GETTING READY TO SEW Extension Table ............................................................................................................... 3 Standard Accessories ..................................................................................................... 3 Accessories Storage Box ................................................................................................ 3 Connecting the Machine to the Power Supply ................................................................ 4 Foot Control ....................................................................................................................4 Presser Foot Lifter........................................................................................................... 5 To Attach and Remove the Presser Foot ........................................................................ 5 Changing Needle ............................................................................................................ 6 Thread and Needle Chart ............................................................................................... 6 Setting Spool Pins ........................................................................................................... 7 Removing or Inserting the Bobbin Case ........................................................................
[Show full text]
4-H CDM Skill-A-Thon Sewing & Clothing ID
4-H CDM Skill-a-Thon Sewing & Clothing ID The photos shown here are only one option of what an item may look like. Other options are available. Revised November 2020 Batik - Indonesian technique of wax resist dyeing applied to whole cloth. This technique originated from Java, Indonesia. It is made either by drawing dots and lines of the resist with a spouted tool called a tjanting, or by printing the resist with a copper stamp called a cap. Broadcloth - A very lightweight, smooth, flat looking fabric, with no pattern in the weave of the threads. It is similar in quality to pinpoint fabric but has less texture. This usually means it is slightly more transparent and not as shiny as the pinpoint. Chambray - A plain weave fabric woven with a colored yarn in the warp and a white yarn in the weft. Corduroy - A fabric with a distinct pattern, a “cord” or wale. It is mostly composed of tufted cords, sometimes exhibiting a channel (bare to the base fabric) between the tufts. Cotton - A fabric made from the fiber of its namesake plant. It is good for first time sewers to use because it’s easy to work with and used for everyday clothing. Eyelet - A type of fabric that has holes that are edged using a buttonhole stitch. The holes are precisely sized and situated to create a pattern or patterns, often floral designs or abstract geometric arrangements. Faux Fur - A fabric fashioned to simulate genuine animal hair. It is known as a pile fabric and is typically made from polymeric fibers that are processed, dyed, and cut to match a specific texture and color.
[Show full text]
SM024 Instruction Book
INSTRUCTION MANUAL SM024 This household sewing machine is designed to comply with IEC/EN/CSA C22.2 No.60335-1 & 60335-2-28 and UL1594. IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic safety precautions should always be followed, including the following: Read all instructions before using this household sewing machine. Keep the instructions at a suitable place close to the machine. Make sure to hand them over if the machine is given to a third party. DANGER - TO REDUCE THE RISK OF ELECTRIC SHOCK: • A sewing machine should never be left unattended when plugged in. Always unplug this sewing machine from the electric outlet immediately after using and before cleaning, removing covers, lubricating or when making any other user servicing adjustments mentioned in the instruction manual. WARNING - TO REDUCE THE RISK OF BURNS, FIRE, ELECTRIC SHOCK, OR INJURY TO PERSON: • Do not allow to be used as a toy. Close attention is necessary when this sewing machine is used by or near children. • Use this sewing machine only for its intended use as described in this manual. Use only attachments recommended by the manufacturer as contained in this manual. • Never operate this sewing machine if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or dropped into water. Return the sewing machine to the nearest authorized service center for examination, repair, electrical or mechanical adjustment. • Never operate the sewing machine with any air openings blocked. Keep ventilation openings of the sewing machine and foot control free from the accumulation of lint, dust, and loose cloth.
[Show full text]
Troubleshooting Embroidery Designs Written By: Kay Hickman, BERNINA Educator, Professional & Home Embroidery Specialist
BERNINA eBook Series JUST EMBROIDER IT! Troubleshooting Embroidery Designs Written by: Kay Hickman, BERNINA Educator, Professional & Home Embroidery Specialist Qualities of a Good Design § Maintenance Proper Setup § Problem / Solution Scenarios § Pressing Matters There is nothing quite as satisfying as stitching a perfect embroidery design for that special project. But it can also be frustrating when things go wrong. In order to troubleshoot and fix embroidery design problems, we need to first understand the qualities of a good design and how preventative maintenance can prevent a lot of issues from occurring in the first place. QUALITIES OF A GOOD DESIGN • The fabric is smooth and pucker-free around the outer edges of the design. • There are no traces of the bobbin thread showing on the top side. • There is no gapping between individual elements of a design or between the fill stitches and the design outlines. BACK SIDE • On the back (bobbin) side, you should see the bobbin thread. You should also see the needle threads around the edges of a fill or either side of a column type design. FRONT SIDE MAINTENANCE Preventative maintenance can go a long way to aid in getting a good stitch out. • Clean the machine every 3 to 4 hours of stitching time. This is especially crucial because the high speed of the embroidery creates more lint and fuzz than you encounter during normal sewing. Remove BEFORE HOOK OIL AFTER HOOK OIL all fuzz and check for tiny bits of thread that might • Follow the manufacturer’s suggestions and take be stuck in the bobbin case.
[Show full text]