DOCSLIB.ORG

Anycast 1 Anycast

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Anycast 1 Anycast Anycast 1 Anycast Anycast is a network addressing and routing methodology in which datagrams from a single sender are routed to the topologically nearest node in a group of potential receivers, though it may be sent to several nodes, all identified by the same destination address. Addressing methodologies Routing schemes anycast broadcast multicast unicast geocast • v • t [1] • e The Internet Protocol and other network addressing systems recognize four main addressing methodologies: Anycast 2 • Unicast addressing uses a one-to-one association between destination address and network endpoint: each destination address uniquely identifies a single receiver endpoint. • Multicast addressing uses a one-to-unique many association, datagrams are routed from a single sender to multiple selected endpoints simultaneously in a single transmission. • Broadcast addressing uses a one-to-many association, datagrams are routed from a single sender to multiple endpoints simultaneously in a single transmission. The network automatically replicates datagrams as needed for all network segments (links) that contain an eligible receiver. • Anycast addressing routes datagrams to a single member of a group of potential receivers that are all identified by the same destination address. This is a one-to-nearest association. Details On the Internet, anycast is usually implemented by using Border Gateway Protocol to simultaneously announce the same destination IP address range from many different places on the Internet. This results in packets addressed to destination addresses in this range being routed to the "nearest" point on the net announcing the given destination IP address. In the past, anycast was suited to connectionless protocols (generally built on UDP), rather than connection-oriented protocols such as TCP that keep their own state. However, there are many cases where TCP anycast is now used. With TCP anycast, there are cases where the receiver selected for any given source may change from time to time as optimal routes change, silently breaking any conversations that may be in progress at the time. These conditions are typically referred to as a "pop switch". To correct for this issue, there have been proprietary advancements within custom IP stacks which allow for healing of stateful protocols where it is required[citation needed]. For this reason, anycast is generally used as a way to provide high availability and load balancing for stateless services such as access to replicated data; for example, DNS service is a distributed service over multiple geographically dispersed servers. Applications With the growth of the Internet, network services increasingly have high-availability requirements. As a result, operation of anycast services (RFC 4786) has grown in popularity among network operators. Domain Name System Nearly all Internet root nameservers are implemented as clusters of hosts using anycast addressing. 12 of the 13 root servers A-M exist in multiple locations, with 11 on multiple continents. (Root server H exists in two U.S. locations. Root server B exists in a single, unspecified location.) The 12 servers with multiple locations use anycast address announcements to provide a decentralized service. This has accelerated the deployment of physical (rather than logical) root servers outside the United States. RFC 3258 documents the use of anycast addressing to provide authoritative DNS services. Many commercial DNS providers have switched to an IP anycast environment to increase query performance, redundancy, and to implement load balancing.[citation needed] Anycast 3 IPv6 transition In IPv4 to IPv6 transitioning, anycast addressing may be deployed to provide IPv6 compatibility to IPv4 hosts. This method, 6to4, uses a default gateway with the IP address 192.88.99.1, as described in RFC 3068. This allows multiple providers to implement 6to4 gateways without hosts having to know each individual provider's gateway addresses. Content delivery networks Content delivery networks may use anycast for actual HTTP connections to their distribution centers, or for DNS. Because most HTTP connections to such networks request static content such as images and style sheets, they are short-lived and stateless. The general stability of routes and statelessness of connections makes anycast suitable for this application, even though it uses TCP[citation needed] . Security Anycast allows any operator whose routing information is accepted by an intermediate router to hijack any packets intended for the anycast address. While this at first sight appears insecure, it is no different from the routing of ordinary IP packets, and no more or less secure. As with conventional IP routing, careful filtering of who is and is not allowed to propagate route announcements is crucial to prevent man-in-the-middle or blackhole attacks. Reliability Anycast is normally highly reliable, as it can provide automatic failover. Anycast applications typically feature external "heartbeat" monitoring of the server's function, and withdraw the route announcement if the server fails. In some cases this is done by the actual servers announcing the anycast prefix to the router over OSPF or another IGP. If the servers die, the router will automatically withdraw the announcement. "Heartbeat" functionality is important because, if the announcement continues for a failed server, the server will act as a "black hole" for nearby clients; this failure mode is the most serious mode of failure for an anycast system. Even in this event, this kind of failure will only cause a total failure for clients that are closer to this server than any other, and will not cause a global failure. Because anycast generally results in a several-fold increase in total network utilization,Wikipedia:Please clarify particularly when used by multiple sources, the reliability of conventional packet transmission may be compromised if sufficient upgrades are not made to allow for additional bandwidth. Mitigating denial-of-service attacks In denial-of-service attacks, a rogue network host may advertise itself as an anycast server for a vital network service, to provide false information or simply block service. Anycast methodologies on the Internet may be exploited to distribute DDoS attacks and reduce their effectiveness: As traffic is routed to the closest node, a process over which the attacker has no control, the DDoS traffic flow will be distributed amongst the closest nodes. Thus, not all nodes might be affected. This may be a reason to deploy anycast addressing. The effectiveness of this technique to divert attacks is questionable, however, because unicast addresses (used for maintenance) can be easy to obtain, at least on IPv6. RFC 2373 defines that "An anycast address must not be used as the source address of an IPv6 packet." Therefore, pinging an anycast address will return the unicast address of the closest node, since the reply must come from a unicast address. An attacker can then attack individual nodes from any location, bypassing anycast addressing methods. This same method works on some, but not all, IPv4 anycast addresses. RFC 2373 also restricted anycast IPv6 addresses to routers only. However, both of these restrictions were Anycast 4 lifted in RFC 4291. Authentication of anycast transmissions may solve this problem. Local and global nodes Some anycast deployments on the Internet distinguish between local and global nodes to benefit the local community, by addressing local nodes preferentially. An example is the Domain Name System. Local nodes are often announced with the no-export BGP community to prevent hosts from announcing them to their peers, i.e. the announcement is kept in the local area. Where both local and global nodes are deployed, the announcements from global nodes are often AS prepended (i.e. the AS is added a few more times) to make the path longer so that a local node announcement is preferred over a global node announcement.[citation needed] References [1] http:/ / en. wikipedia. org/ w/ index. php?title=Template:Routing_scheme& action=edit External links • Best Practices in IPv4 Anycast Routing (http:/ / www. pch. net/ resources/ papers/ ipv4-anycast/ ipv4-anycast. pdf) Tutorial on anycast routing configuration. • DNS Service Architectures (http:/ / www. pch. net/ resources/ papers/ dns-service-architecture/ dns-service-architecture-v11. pdf) Packet Clearing House paper on the use of anycast addressing in the construction of DNS service architectures. • Anycast Performance (http:/ / www. pch. net/ resources/ papers/ anycast-performance/ anycast-performance-v10. pdf) Analysis of the performance and geographic specificity of anycast DNS servers. • Anycast Addressing on the Internet (http:/ / aharp. ittns. northwestern. edu/ papers/ k5-anycast/ index. html) • Distributing Authoritative Name Servers via Shared Unicast Addresses (http:/ / www. ietf. org/ rfc/ rfc3258. txt), IETF RFC describing the distribution of authoritative DNS servers using anycast. • Operation of Anycast Services (http:/ / www. ietf. org/ rfc/ rfc4786. txt), IETF RFC offering advice on how to deploy services using anycast. • Hierarchical Anycast for Global Service Distribution (http:/ / ftp. isc. org/ isc/ pubs/ tn/ isc-tn-2003-1. html), ISC document on anycast • Effect of anycast on K-root (http:/ / ripe. net/ info/ ncc/ presentations/ anycast-kroot. pdf), presentation by Lorenzo Colitti (RIPE NCC) at DNS-OARC in July 2005 • The Impact of anycast on Root DNS Servers: The Case of K-root (http:/ / www. ripe.
Load more

Recommended publications
  • Performance Evaluation of TCP Multihoming for IPV6 Anycast Networks and Proxy Placement
    University of Central Florida STARS Electronic Theses and Dissertations, 2004-2019 2015 Performance Evaluation of TCP Multihoming for IPV6 Anycast Networks and Proxy Placement Raya Alsharfa University of Central Florida Part of the Electrical and Electronics Commons Find similar works at: https://stars.library.ucf.edu/etd University of Central Florida Libraries http://library.ucf.edu This Masters Thesis (Open Access) is brought to you for free and open access by STARS. It has been accepted for inclusion in Electronic Theses and Dissertations, 2004-2019 by an authorized administrator of STARS. For more information, please contact [email protected]. STARS Citation Alsharfa, Raya, "Performance Evaluation of TCP Multihoming for IPV6 Anycast Networks and Proxy Placement" (2015). Electronic Theses and Dissertations, 2004-2019. 1350. https://stars.library.ucf.edu/etd/1350 PERFORMANCE EVALUATION OF TCP MULTIHOMING FOR IPV6 ANYCAST NETWORKS AND PROXY PLACEMENT by RAYA MAJID ALSHARFA B.S. NAJAF TECHNICAL COLLEGE, 2010 A thesis submitted in partial fulfillment of the requirements for the degree of Master of Science in Electrical Engineering. in the Department of Electrical Engineering and Computer Science in the College of Engineering and Computer Science at the University of Central Florida Orlando, Florida Fall Term 2015 Major Professor: Mostafa Bassiouni © 2015 Raya Majid Alsharfa ii ABSTRACT In this thesis, the impact of multihomed clients and multihomed proxy servers on the performance of modern networks is investigated. The network model used in our investigation integrates three main components: the new one-to-any Anycast communication paradigm that facilitates server replication, the next generation Internet Protocol Version 6 (IPv6) that offers larger address space for packet switched networks, and the emerging multihoming trend of connecting devices and smart phones to more than one Internet service provider thereby acquiring more than one IP address.
    [Show full text]
  • DNS Anycast for High Availability and Performance DNS Anycast Addressing for High Availability and by Timothy Rooney Performance Product Management Director
    White Paper DNS Anycast for High Availability and Performance DNS Anycast Addressing for High Availability and by Timothy Rooney Performance Product management director BT Diamond IP By Tim Rooney Director, Product Management BT Diamond IP www.btdiamondip.com DNS Anycast for High Availability and Performance By Tim Rooney, Director, Product Management Introduction We’ve all heard the mantra, “do more with less,” – for some of us to the point of numbness. But when it comes to mission-critical DNS name resolution services, any suggestion of skimping is likely to evoke defiance from those responsible for maintaining its availability and performance. One strategy, however, that can make the deployment of DNS services more efficient is the use of anycast addressing. This white paper shows how DNS servers can be deployed with anycast to achieve a number of benefits, including higher availability and resilience. Defining Anycast The term anycast refers to an IP address assigned to a set of interfaces (usually belonging to different nodes), any one of which can be the intended recipient. Anycast addresses are assigned from the same address space from which unicast addresses have been allocated. Thus, unlike private address space, one cannot visually differentiate a unicast address from an anycast address. An IP packet destined for an anycast address is routed to the nearest interface (according to routing table metrics) configured with the anycast address. The concept is that the sender doesn’t necessarily care which particular host, or in this case DNS server, receives the packet, just as long as one of those sharing the anycast address receives it.
    [Show full text]
  • Towards Passive Analysis of Anycast in Global Routing: Unintended Impact of Remote Peering
    Towards Passive Analysis of Anycast in Global Routing: Unintended Impact of Remote Peering Rui Bian Shuai Hao Haining Wang University of Delaware CAIDA / UC San Diego University of Delaware bianrui@udel:edu haos@caida:org hnw@udel:edu Amogh Dhamdere Alberto Dainotti Chase Cotton CAIDA / UC San Diego CAIDA / UC San Diego University of Delaware amogh@caida:org alberto@caida:org ccotton@udel:edu ABSTRACT adoption [8] or the efficiency in particular services like DNS[18]. Anycast has been widely adopted by today’s Internet services, in- Due to the insufficient distinctions between unicast and anycast cluding DNS, CDN, and DDoS protection, in which the same IP from the perspective of a routing table, the common method to address is announced from distributed locations and clients are di- identify anycast addresses is through active Internet-wide measure- rected to the topologically-nearest service replica. Prior research has ments. Cicalese et al. [8, 9] studied the enumeration and city-level focused on various aspects of anycast, either its usage in particular geolocation of anycast prefixes by using latency measurements services such as DNS or characterizing its adoption by Internet- based on the detection of speed-of-light violations. However, the wide active probing methods. In this paper, we first explore an latency of ping may not always reliably reflect the geographic dis- alternative approach to characterize anycast based on previously tance of two IP addresses [4, 34]. Also, active probing requires the collected global BGP routing information. Leveraging state-of-the- use of many vantage points to achieve the necessary coverage.
    [Show full text]
  • Crain-Haiti-Anycast-En.Pdf
    Anycasting the DNS John Crain Internet Corporation for Assigned Names and Numbers What is Anycast? ‣ “Anycast is a network addressing and routing scheme whereby data is routed to the "nearest" or "best" destination as viewed by the routing topology.” - Wikipedia ‣ unicast - IP address is a unique interface ‣ multicast - Multiple locations at same IP address all receiving packets. ‣ anycast - IP address points to multiple locations but only one visible. Limitations ‣ Because routing information can change! ‣ UDP protocols ‣ Short lived TCP sessions ‣ This sounds a lot like DNS packets :) ‣ Not good for longer TCP sessions ‣ Think of a web session that can last seconds or videostreaming that can last even longer! Why do it? ‣ Adds Capacity ‣ 2 x 100Mb is more than 1 x 100Mb ‣ Localizes trafc ‣ Means closer, hence faster replies ‣ During attacks it also localizes problems ‣ It’s FUN!!!! Is it hard? ‣ Not really but there are some considerations ‣ Managing the anycast instances takes some thought ‣ Need multiple IP address ranges... ‣ More on that..... Implementing Anycast Separate DNS server into it’s own network ‣ Get a dedicated routable /24 of IPv4 space and a range of IPv6 space ‣ Also get a dedicated Autonomous System Number (ASN) ‣ This is necessary for creating a unique routing entity ‣ ICANN L-ROOT (NET6-2001-500-3-1) 2001:0500:0003:0000:0000:0000:0000:0000 - 2001:0500:0003:FFFF:FFFF:FFFF:FFFF:FFFF ‣ ICANN L-ROOT (NET-199-7-83-0-1) 199.7.83.0 - 199.7.83.255 ‣ ASNumber: 20144 A name server ‣ Has an IP address on which it answers DNS queries.
    [Show full text]
  • Unicast Forwarding
    Unicast Forwarding • Unicast Forwarding, page 1 Unicast Forwarding The Enhanced Forwarding functionality consists of the following: • End Host Registration and Tracking: Leaf switch will intercept the ARP and DHCP packets and learns the IP to MAC binding for the host. In the case of virtualized environments, VDP may be used to track the VM moves. • End Host Route Distribution using BGP: MP-BGP is used within the Vinci fabric to distribute the IP reachability information across the leaf switches in the fabric. Route reflectors will be used for scalability purposes. • ARP and IPv6 ND Proxy: One of the goals of Vinci Enhanced forwarding is to eliminate flooding across the fabric. For this purpose, every leaf switch will act as a ARP/IPv6 ND proxy for all the hosts connected to the leaf switch. • Anycast Default Gateway: Leaf switches act as the default gateway for routing across subnets. All the leafs that handle a given subnet are configured with the same anycast IP address and MAC address. • Forwarding Behavior at Leaf switches: A fabric VLAN is allocated per tenant VRF in the Vinci fabric. BGP advertises the reachability of hosts attached to remote leafs to all the leaf nodes. Ingress leaf switch routes the traffic from the tenant VLAN to the egress leaf switch where the destination host is attached via the fabric VLAN. Egress leaf switch routes the traffic back to the tenant VLAN. This allow the platforms to optimize by scaling the FIB host route table without scaling the MAC address table. • Routing within the subnet: Leaf switch responds with the Anycast Default Gateway MAC to the ARP requests for hosts within the same subnet.
    [Show full text]
  • L-Root and Internet in LAC Mauricio Vergara Ereche | Qos Internet CEPAL | Oct 2015 Agenda
    L-Root and Internet in LAC Mauricio Vergara Ereche | QoS Internet CEPAL | Oct 2015 Agenda 1 2 3 What is L-Root LAC ICANN? Connectivity 4 5 Our model for Recommend deployment ations | 2 What is ICANN? What is a resilient and secure Internet? Quick Look at ICANN Overview ICANN is a global multi-stakeholder, private sector organization that manages Internet resources for the public benefit. It is best known for its role as technical coordinator of the Internet’s Domain Name System Mission To coordinate, at the overall level, the global Internet’s system of unique identifiers, and in particular to ensure the stable and secure operation of the Internet’s unique identifier system | 4 Supporting A Healthy, Resilient Internet | 5 SSR: Security, Stability and Resiliency Secure 1 Capacity to protect and prevent misuse of Internet Unique identifiers Stable Capacity to ensure that the system operates as expected, 2 and that users of the unique identifiers have confidence that the system operates as expected Resilient Capacity of the unique identifier system to effectively 3 withstand/tolerate/survive malicious attacks and other disruptive events without disruption or cessation of service | 6 L-Root DNS and Anycasting How DNS Works? Root Server 2 www.icann.org ? 1 3 4 8 .ORG Server 5 DNS Resolver (ISP) 6 9 7 www.icann.org ICANN.ORG Server | 8 What is L-Root? “L” is one of 13 independently operated root servers serving the DNS root zone ICANN DNS Engineering team operates L under the Autonomous System Number (ASN) AS20144 using the following
    [Show full text]
  • Implementation of DNS Anycast a Case Study
    Implementation of DNS Anycast a case study A. S. M. Shamim Reza | Md. Tawhidul Islam Bhuiyan Network Operation Center Link3 Technologies Ltd • Linux Geek • [~]$whoami Open Source Software Enthusiast | • EC-Council Certifed Security Analyst ASMShamimReza [email protected] [email protected] What is Anycast ? Anycast is a routing method in which incoming requests can be routed to a variety of diferent locations. The Journey • Why Anycast DNS – background history • Challenges – that we have faced • Deployment – what we have done • Confguration – the fun part • Performance & Security tuning – do’s & don’t Why Anycast DNS background history What we have faced ? 1. Existing DNS server OS version was about to obsolete 2. Resource utilization was always 95%-99% 3. When server was attacked with DDOS a. Query response delayed & most of the cases it stopped answering b. Unstable DNS service for user internet accesss 4. Log search was not administration friendly 5. No log options for Recursive query DNS Server – What we had Authoritative Recursive DNS Software resources Hardware resources CentOS 5 32 bit Core – 2 bind-utils-9.3.4-10.P1.el5 RAM – 4 GB ypbind-1.19-11.el5 HDD – Sata 7.2k RPM bind-libs-9.3.4-10.P1.el5 Why we choose Anycast • Because of the advantages – • users of an anycast service will always connect to the closest DNS server; This reduces latency, • if one server is being overly loaded, simply deploy another one in a location that would allow it to take some proportion of the overloaded server's requests; horizontal scaling. • We need to have 1 single IP for the Recursive DNS server all over Bangladesh.
    [Show full text]
  • AWS Certified Advanced Networking - Specialty Exam
    N E T 2 0 7 - R Understanding the basics of IPv6 networking on AWS Shakeel Ahmad Solutions Architect Amazon Web Services © 2019, Amazon Web Services, Inc. or its affiliates. All rights reserved. Agenda Why IPv6 Brief overview of the IPv6 protocol IPv6 in Amazon VPC IPv4 to IPv6 migration patterns Hands-on with IPv6 on AWS © 2019, Amazon Web Services, Inc. or its affiliates. All rights reserved. IPv4 exhaustion IPv4 vs IPv6 address size IPv4: 32-bit / 4,294,967,296 addresses (~4.3 x 109) 11000000 00000000 00000010 00000001 IPv6: 128-bit / 340,282,366,920,938,463,463,374,607,431,768,211,456 addresses (~3.4 x 1038) 0010000000000001 0000110110111000 0000111011000010 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000001 © 2019, Amazon Web Services, Inc. or its affiliates. All rights reserved. IPv4 vs IPv6 address types IPv4: Address types 1. Unicast 2. Broadcast 3. Multicast IPv6: Address types 1. Unicast 2. Multicast 3. Anycast IPv4 vs IPv6 address format IPv4: Dotted Decimal Notation + CIDR 192.168.0.1/24 127.0.0.1 IPv6: Colon-Separated Hextet Notation + CIDR 2001:0db8:0ec2:0000:0000:0000:0000:0001/64 0000:0000:0000:0000:0000:0000:0000:0001 2001:db8:ec2:0:0:0:0:1/64 0:0:0:0:0:0:0:1 2001:db8:ec2::1/64 ::1 © 2019, Amazon Web Services, Inc. or its affiliates. All rights reserved. Amazon VPC—dual-stack VPC Internet gateway IPv4: IPv6: Instance Public Subnet Amazon VPC—private subnet? NAT? VPC Egress-only internet gateway IPv4: IPv6: Instance X Private subnet Amazon VPC—IPv6 routing and more .
    [Show full text]
  • How Cloud-Based Dns Improves Digital Performance and Resilience
    Ebook: HOW CLOUD-BASED DNS IMPROVES DIGITAL PERFORMANCE AND RESILIENCE dyn.com 603 668 4998 150 Dowdyn.com Street, Mancheste603r, NH 668 031 499801 US A 150@dyn Dow Street, Manchester, NH 03101 USA @dyn High Availability DNS Reduces Downtime Risk and Improves End-User Experience How Redundant DNS Services Provide Resilience and Improve Application Performance In this guide you will learn: The critical role DNS plays in the user experience The difference between unicast and anycast-based Introduction DNS implementations DNS is the first link in your digital supply chain. Every user’s first interaction with your website begins with a series of DNS queries. Poor DNS The hidden costs, risks, and challenges performance can lead to slow page loads, dissatisfied customers, damage of managing your own on-premises to your brand, and lost business—so a “set it and forget it” approach to DNS infrastructure or using an DNS simply doesn’t work in the digital age. “add-on” DNS service from your ISP That’s why cloud-based, managed DNS services are now the norm for born- in-the-cloud companies—and increasingly for enterprise companies as well. The performance, reliability, They can enhance DNS performance, resiliency, and scalability, helping you and security advantages of a ensure superior user experience worldwide. This paper reviews the features cloud-based DNS service and benefits of a cloud-based DNS service. page 2 dyn.com @dyn Ebook | How Cloud-based DNS Improves Digital Performance and Resilience “Page size and complexity typically DNS Overview correlate to slower load times. The median page is 1945 KB in size and The Domain Name System (DNS) is a distributed internet database that contains 169 resource requests.
    [Show full text]
  • Network Layer Implemented Anycast Load Balancing
    Network layer implemented Anycast Load Balancing Ricardo Lopes Pereira Teresa Vaz˜ao IST, Inesc-ID IST, Inesc-ID [email protected] [email protected] Abstract only server availability, but also the network distance and conditions along the paths from client to server and vice- This paper presents a server selection method where the versa. This is also what routing protocols such as Open server selection is performed by the network, at the first Shortest Path First (OSPF) do, compute shortest paths. As- router from the client. This method, usable in networks un- signing each server the same anycast address [16] allows der single administrative control, combines network metrics each router to know the path towards the nearest server. (such as traffic or latency) with common server load bal- When clients use the anycast address to reach servers, the ancing metrics (such as load, CPU utilisation or response network layer will automatically forward packets to the time), allowing network conditions to be taken into account nearest server (according to the routing metrics) [9]. This when selecting the server which will handle the request. method is successfully being used today in the Internet to The performance of this technique was compared, by distribute User Datagram Protocol (UDP) queries by the means of simulations, to that of widely used techniques such Domain Name System (DNS) root servers [6]. as random, round robin and least loaded server selection. This paper presents a transparent load balancing tech- nique usable on networks under common administrative control, which aims at providing unmodified clients with 1 Introduction better reply times while maximising the total number of re- quests handled by the set of servers.
    [Show full text]
  • Routing-Independent Anycast for Ipv6 Content Delivery Networks
    ROUTING-INDEPENDENT ANYCAST FOR IPV6 CONTENT DELIVERY NETWORKS by YINHANG CHENG Submitted in partial fulfillment of the requirements for the degree of Master of Science Department of Electrical Engineering and Computer Science CASE WESTERN RESERVE UNIVERSITY August 2019 CASE WESTERN RESERVE UNIVERSITY SCHOOL OF GRADUATE STUDIES We hereby approve the thesis of Yinhang Cheng candidate for the degree of Master of Science Committee Chair Michael Rabinovich Committee Member Michael Rabinovich Committee Member Vincenzo Liberatore Committee Member An Wang Date of Defense 06/21/2019 *We also certify that written approval has been obtained for any proprietary material contained therein. Table of Contents List of Tables...................................................................................................................V List of Figures................................................................................................................ VI Abstract.......................................................................................................................VII 1. Introduction................................................................................................................8 2. Background...............................................................................................................11 2.1 DNS-based Request Routing in CDN................................................................11 2.2 IPv6 Mobility....................................................................................................13
    [Show full text]
  • Bidirectional Anycast/Unicast Probing (BAUP): Optimizing CDN Anycast
    Bidirectional Anycast/Unicast Probing (BAUP): Optimizing CDN Anycast Lan Wei∗ Marcel Floresy Harkeerat Bediy John Heidemann∗ ∗ USC/Information Sciences Institute y Verizon Digital Media Services fweilan, [email protected] fmarcel.flores, [email protected] Abstract—IP anycast is widely used today in Content Delivery between large latencies that are due to problems (say, a path Networks (CDNs) and for Domain Name System (DNS) to provide that misses a shorter route) from latency that is inherent efficient service to clients from multiple physical points-of- (for example, users connecting via satellite or over long presence (PoPs). Anycast depends on BGP routing to map users to PoPs, so anycast efficiency depends on both the CDN operator distances). Root causes are challenging to find because even and the routing policies of other ISPs. Detecting and diagnosing though measurement can provide latencies and paths, we inefficiency is challenging in this distributed environment. We do not know why problems occur. Finally, once problems propose Bidirectional Anycast/Unicast Probing (BAUP), a new have been identified (for example, a provider known to have approach that detects anycast routing problems by comparing frequent congestion), the CDN must determine solutions to anycast and unicast latencies. BAUP measures latency to help us identify problems experienced by clients, triggering traceroutes those problems. Solutions are not always possible and can to localize the cause and suggest opportunities for improvement. be difficult to determine, particularly when the problem is Evaluating BAUP on a large, commercial CDN, we show that multiple hops away from the CDN. problems happens to 1.59% of observers, and we find multiple Our first contribution is to design Bidirectional Any- opportunities to improve service.
    [Show full text]