ITB Amendment Form

Total Page：16

File Type：pdf, Size：1020Kb

STATE OF ALASKA ITB NUMBER 2019-1200-4110-A ADDENDUM NUMBER THREE RETURN THIS ADDENDUM TO THE ISSUING OFFICE AT: Department of Public Safety Division of Administrative Services Procurement Section 4805 Dr. Martin Luther King Jr. Avenue Anchorage, Alaska 99507 THIS IS NOT AN ORDER DATE ADDENDUM ISSUED: April 12, 2019 ITB TITLE: Anchor Windlass: Removal of Existing, Fabrication, and Installation for the Alaska Wildlife Troopers Vessel Section, Kodiak Based 156’ Patrol Vessel Stimson ITB OPENING DATE AND TIME IS CHANGED: June 3, 2019 at 11:00 AM Alaska Time The ITB for the above project is amended as follows. All other terms and conditions remain the same: 1. Extend the opening date and time to June 3, 2019 at 11:00 AM Alaska Time. 2. Extend the completion date for installation of the anchor windlass to June 1, 2020. 3. Any questions not addressed below will be answered in a subsequent addendum to the ITB. 4. QUESTIONS AND ANSWERS: Q1. Not just one, but both the supply and return hydraulic lines from the foc'sle to their termination above the weather deck will need to be up sized with the correct size (TBD by winch motor ports). Answer: Both supply lines will have to be increased (doubled) prior to install to allow for a higher speed windlass. Q2. The portion of the pipes that protrude above the deck will need to be stainless steel. Answer: Yes, all above deck piping will be stainless. Q3. Fitting adapters and hose crimp ends will need to be constructed of stainless steel. Answer: Yes. Q4. New anchor winch requires a Capstan head on the starboard side. Answer: Yes. STATE OF ALASKA ITB NUMBER 2019-1200-4110-A ADDENDUM NUMBER THREE Q5. Install additional frame stiffeners in the overhead of the foc'sle Answer: To be determined by a marine architect to verify the requirement of additional framing to support the weight and torque placed on the deck by additional chain and a heavier windlass. The response from the marine architect will be provided in a subsequent addendum. Jackie Lea Procurement Officer State of Alaska – Department of Public Safety Administrative Services, Procurement Section Desk: 907.269.7661 E-mail: [email protected] END OF ADDENDUM NUMBER THREE .

Copy Link

Recommended publications

Coast Guard Cutter Seamanship Manual
U.S. Department of Homeland Security United States Coast Guard COAST GUARD CUTTER SEAMANSHIP MANUAL COMDTINST M3120.9 November 2020 Commandant US Coast Guard Stop 7324 United States Coast Guard 2703 Martin Luther King Jr. Ave SE Washington, DC 20593-7324 Staff Symbol: (CG-751) Phone: (202) 372-2330 COMDTINST M3120.9 04 NOV 2020 COMMANDANT INSTRUCTION M3120.9 Subj: COAST GUARD CUTTER SEAMANSHIP MANUAL Ref: (a) Risk Management (RM), COMDTINST 3500.3 (series) (b) Rescue and Survival Systems Manual, COMDTINST M10470.10 (series) (c) Cutter Organization Manual, COMDTINST M5400.16 (series) (d) Naval Engineering Manual, COMDTINST M9000.6 (series) (e) Naval Ships' Technical Manual (NSTM), Wire and Fiber Rope and Rigging, Chapter 613 (f) Naval Ships’ Technical Manual (NSTM), Mooring and Towing, Chapter 582 (g) Cutter Anchoring Operations Tactics, Techniques, and Procedures (TTP), CGTTP 3-91.19 (h) Cutter Training and Qualification Manual, COMDTINST M3502.4 (series) (i) Shipboard Side Launch and Recovery Tactics, Techniques, and Procedures (TTP), CGTTP 3-91.25 (series) (j) Shipboard Launch and Recovery: WMSL 418’ Tactics, Techniques, and Procedures (TTP), CGTTP 3-91.7 (series) (k) Naval Ships’ Technical Manual (NSTM), Boats and Small Craft, Chapter 583 (l) Naval Ship’s Technical Manual (NSTM), Cranes, Chapter 589 (m) Cutter Astern Fueling at Sea (AFAS) Tactics, Techniques, and Procedures (TTP), CGTTP 3-91.20 (n) Helicopter Hoisting for Non-Flight Deck Vessels, Tactics, Techniques, and Procedures (TTP), CGTTP 3-91.26 (o) Flight Manual USCG Series
[Show full text]
Readin' Both Pages
Readin’ Both Pages A membership publication of the Sail, Power & Steam Museum Vol. 1, No. 1 Winter 2008 Rekord ~ A Fascinating Freighter From the Memoirs of Capt. Jim Sharp Life is too short to own an ugly boat! That was my motto and I adhered to it with almost religious devotion. The next boat I was destined to drag into Camden Harbor was one interesting and handsome vessel. Although sailing was still very much my forte, this little ship conveyed the closest thing to worship of a power vessel that this old codger can conjure up. She was called the Record, spelled Rekord in old Norwegian, and was more than attractive in a thousand different ways. Rekord had history, intrigue, humor, challenge, personality and humility, all trunnelled together into one magniﬁcent hull. Museum volunteers and staff were busy throughout the summer season working on many projects aboard Rekord. In this picture, Ben Breda applies fresh white paint to the starboard foredeck rail. Her ad was buried deep among the many listings in the “Yellow Pages” (that’s the scandal sheet of boats for sale shoe ... it was not bad. There was some worming, but noth- in the commercial world). I should never have taken my ing that would be a structural problem. And those worms copy into Fitzpatrick’s Deli to peruse the Boats For Sale would soon die in our cold Maine water. I think I knew I listings over my coffee. It was just a small picture and would buy this boat before even stepping aboard. Then I really fuzzy, but it snapped the hair-trigger on my snooping asked the owner about the engine.
[Show full text]
Boston Harbor Auctions
Boston Harbor Auctions NAUTICAL ANTIQUE AND SHIP MODEL AUCTION Saturday - April 20, 2019 NAUTICAL ANTIQUE AND SHIP MODEL AUCTION 1: Samuel Walters Marine Painting USD 4,000 - 6,000 Fine, painting of the clipper ship Mary Moore by Samuel Walters. The vessel is shown under shortened sail, and carries a house flag and British flag. Large canvas. On sight 51 x 33. Overall 58 x 40. 2: Boston built tugboat painting USD 450 - 650 Oil painting of army tug DPC 16. Built by Lawley and Son, Neponset Mass in 1944. She was 86 feet long. Sold in 1946 as Gremlin, later Alice St. Philip and Honcho. Tug is shown in great detail. Rear of canvas states FINISHED 9/22/44. 26 X 19 3: George Lawley Painting USD 300 - 500 Painting originally from the George Lawley and Son shipyard in Boston. This is of the Lawley Built US Navy sub chaser launched at Neponset Mass 1943 and commissioned as USS PC 1087 painted in 1944 by Benjamin Stephenson. Signed lower right STEPHENSON. 31 x 20 4: Tropical naval ship landing painting USD 300 - 500 Original oil by Benjamin T. Stephenson. The reader of canvas reads: USS LCI 691, (center line ramp) titled EARLY MORNING LANDING OPERATION. Painted by Benjamin T. Stephenson 14 Longmeadow Road finished Oct 27, 1944. 31 x 20 5: Landing craft support LCS 1 Painting USD 250 - 450 Original oil painting showing a US Navy World War II LCS-1 landing craft ship underway. Back is marked with artists Benjamin T. Stephenson, 14 Longmeadow Road, Newton Corner, Massachusetts.
[Show full text]
31' Camano Troll
31’ Camano Troll 31’ Camano Troll . Year: 2003 . Boat Name: MV Puffin . Located in Sidney, BC . Hull Material: Fiberglass . Engine/Fuel Type: Single diesel . Pristine and beautifully equipped . Boathouse kept $ 154,900 CAD Boat last out-of-water for bottom paint/zincs spring 2013. Boat mechanically serviced spring 2013. Major Price Adjustment August 30th, 2013. Owner will look at aggressive sale pricing to buyer of the combination of boat and boathouse (boathouse moorage paid to March 31st, 2014)!! Come and tour this beautiful Camano. www.vanislemarina.com 31’ Camano Troll www.vanislemarina.com 31’ Camano Troll Dimensions Engine LOA: 31 ft 0 in Engine Brand: Volvo Beam: 10 ft 5 in Year Built: 2003 Minimum Draft: 3 ft 2 in Engine Model: TMD 41T Headroom: 6 ft 5 in Engine Type: Inboard Dry Weight: 12000 lbs Engine/Fuel Type: Diesel Engine Hours: 1150 Tanks Propeller: 3 blade propeller Fuel Tanks: 2 (50 Gallons) Drive Type: Direct Drive Engine(s) Total Power: 200 HP Accommodations Number of double berths: 1 Covers Number of cabins: 2 Bimini Top Number of heads: 1 www.vanislemarina.com 31’ Camano Troll Inside Equipment Electronics Oven Compass Microwave oven CD player Refrigerator Plotter Battery charger - and inverter GPS Electric bilge pump Cockpit speakers Manual bilge pump Radar Heating - Webasto diesel furnace Autopilot Bow thruster Navigation center Electric head VHF Hot water Radio Outside Equipment/Extras Electrical Equipment Swimming ladder Inverter Davits Shore power inlet Tender Electrical Circuit: 110V Electric windlass Electronics . Icom VHF radio . Marine radar . Integrated (2) station Furuno plotters with radar overlay . Simrad auto pilot AP26, (1) Simrad R3000x remote, c/w rudder angle indicator .
[Show full text]
Anchor Chain and Windlass?
Anchor loss - technical and operational challenges and recommendations DNV GL, Gard and The Swedish Club March 2016 Ungraded © DNV GL AS 2016. All rights reserved 1 DNV GL © 2016 29 February 2016 SAFER, SMARTER, GREENER Anchor loss – prevention - Content ° Background ° Technical issues and recommendations ° Operational issues and recommendations ° Legal notice Ungraded 2 DNV GL © 2016 29 February 2016 Why focus on anchor loss - lost per year? Anchors lost per 100 ship year since 2007 ° DNV GL has observed a relatively high number of anchor losses with 8-10 anchors lost per 1000 ships per year and a negative trend in 2014/2015 Anchor lost due to D-link opening up DNV GL Anchors lost per 100 ship year ( DNV GL fleet) Ungraded 3 DNV GL © 2016 29 February 2016 Anchor losses per ship type Anchors lost per 100 ship year & ship type ° Tanker for oil and Passenger Ships more exposed ° Reflecting the ship type trading pattern? Anchor losses per 100 ship-year and ship type 1,200 1,000 0,800 0,600 0,400 0,200 Loss per 100 Shipyear DNV Fleet 2010-2015 0,000 DNV GL Anchors lost per 100 ship year & ship type ( DNV fleet) Ungraded 4 DNV GL © 2016 29 February 2016 Costs involved with loss of anchors Swedish Club claims including deductible – loss of anchor Swedish Club claims including deductible ° Direct cost to replace lost anchor and chain ° Gard has seen increasing costs related to recovering lost anchors amounting up to USD 50 000 ° Delays and off-hire ° Cost due to grounding / collision / damage to subsea equipment etc.
[Show full text]
Abyc H-40 (Pdf)
H-40 7/03 H-40 ANCHORING, MOORING, AND STRONG POINTS Table of Contents 40.1 PURPOSE .......................................................................................................................................................1 40.2 SCOPE ............................................................................................................................................................1 40.3 DEFINITIONS................................................................................................................................................1 40.4 ANCHORING AND MOORING ...................................................................................................................1 40.5 TOWING AND TRAILERING ......................................................................................................................2 40.6 LIFTING SYSTEMS ......................................................................................................................................2 40.7 OWNER’S MANUALS..................................................................................................................................3 APPENDIX ...................................................................................................................................................................5 H-40 7/03 H-40 ANCHORING, MOORING, AND STRONG POINTS Based on ABYC’s assessment of the existing technology, Chain stopper - A device designed to secure the chain and and the problems associated with achieving the goals
[Show full text]
Requirements Concerning MOORING, ANCHORING and TOWING
INTERNATIONAL ASSOCIATION OF CLASSIFICATION SOCIETIES Requirements concerning MOORING, ANCHORING AND TOWING CONTENTS A1 Anchoring Equipment Corr.2 Mar 2017 A2 Shipboard fittings and supporting hull structures associated with towing and mooring on conventional ships Corr.2 Mar 2017 A3 Anchor Windlass Design and Testing June 2017 Page 1 IACS Req. 2017 A1 A1A1 Anchoring Equipment (1981) (cont) (Rev.1 A1.1 Design of the anchoring equipment 1987) (Rev.2 A1.1.1 The anchoring equipment required herewith is intended for temporary mooring of a 1992) ship within a harbour or sheltered area when the ship is awaiting berth, tide, etc. IACS (Rev.3 Recommendation No. 10 ‘Anchoring, Mooring and Towing Equipment’ may be referred to for 1994) recommendations concerning anchoring equipment for ships in deep and unsheltered water. (Rev.4 Aug A1.1.2 The equipment is therefore not designed to hold a ship off fully exposed coasts in 1999) rough weather or to stop a ship which is moving or drifting. In this condition the loads on the (Rev.5 anchoring equipment increase to such a degree that its components may be damaged or lost Jun owing to the high energy forces generated, particularly in large ships. 2005) (Rev.6 A1.1.3 The anchoring equipment required herewith is designed to hold a ship in good Oct holding ground in conditions such as to avoid dragging of the anchor. In poor holding ground 2016) the holding power of the anchors is significantly reduced. (Corr.1 Dec A1.1.4 The Equipment Number (EN) formulae for anchoring equipment as given in A1.2 and 2016) A1.3 are based on an assumed maximum current speed of 2.5 m/s, maximum wind speed of (Corr.2 25 m/s and a minimum scope of chain cable of 6, the scope being the ratio between length of Mar chain paid out and water depth.
[Show full text]
Anchor Windlass
Anchor Windlass June 2020 Rule Note NR 626 DT R03 E Marine & Offshore Le Triangle de l’Arche - 8 Cours du Triangle - CS 50101 92937 Paris La Defense Cedex - France Tel: + 33 (0)1 55 24 70 00 https://marine-offshore.bureauveritas.com/bv-rules © 2020 Bureau Veritas – All rights reserved BUREAU VERITAS MARINE & OFFSHORE 6.2 Without prejudice to any other rights hereunder, in case of Client’s payment default, the Society shall be entitled to charge, in addition to the amount not properly paid, interests equal to twelve (12) months LIBOR plus two (2) per cent as of due date calculated on the number of days such payment is delinquent. The Society shall also have the GENERAL CONDITIONS right to withhold Certificates and other documents and/or to suspend or revoke the validity of Certificates. 6.3 In case of dispute on the invoice amount, the undisputed portion of the invoice shall be paid and an explanation 1. INDEPENDENCE OF THE SOCIETY AND APPLICABLE TERMS on the dispute shall accompany payment so that action can be taken to solve the dispute. 1.1 The Society shall remain at all times an independent contractor and neither the Society nor any of its officers, 7. LIABILITY employees, servants, agents or subcontractors shall be or act as an employee, servant or agent of any other party 7.1 The Society bears no liability for consequential loss. For the purpose of this clause consequential loss shall hereto in the performance of the Services. include, without limitation: 1.2 The operations of the Society in providing its Services are exclusively conducted by way of random inspections • Indirect or consequential loss; and do not, in any circumstances, involve monitoring or exhaustive verification.
[Show full text]
Morris Yachts M52 – Audacity
Morris Yachts M52 – Audacity Make: Morris Yachts Boat Name: Audacity Model: M52 Hull Material: Composite Length: 52 ft Draft: 6 ft 8 in Price: $ 1,475,000 Number of Engines: 1 Year: 2012 Fuel Type: Diesel Condition: Used Number: 4131152 Location: San Francisco, CA, United States Audacity Morris Yachts M-Series M52 is a beautiful and logical evolution of the impressive success of her smaller sister-ships, the M36 Daysailer and the M42 Weekender. The M52 adheres faithfully to the fundamental philosophy laid down for the M-series: classic beauty, extraordinary ease of handling (including electric winches, electric furling, and bow thruster), and emphasis on the fundamentals of comfortable sailing. Her greater length and volume allow her to provide an even larger cockpit for daysailing - an M Series trademark - yet offer spacious Morris Yachts - Wythe Ingebritson 14 Harbor Drive, Northeast Harbor, ME 04662, United States Toll-free: 877-225-6689 Tel: 207-664-8111 Tel: 207-244-5509 [email protected] http://www.morrisyachts.com and comfortable accommodations for cruising, and still give great performance (with a proven mixed fleet racing record culminating in her class win at the 2016 Rolex Big Boat series in San Francisco). AUDACITY is for sale from her original owner who has professionally maintained her in like new condition. Set up to be equally capable of racing with a full crew and enhanced sail inventory, cruised with family or friends or singlehanded daysailing, AUDACITY is both Northern California PHRF and fully ORR rated for inshore, offshore or coastal racing. She is an extremely versatile yacht and will make her new owner proud wherever she goes.
[Show full text]
Nicholas Potter N Class 62 Ft Sloop 1938
HERITAGE, VINTAGE AND CLASSIC YACHTS +44 (0)1202 330 077 NICHOLAS POTTER N CLASS 62 FT SLOOP 1938 Specification SERENADE NICHOLAS POTTER N CLASS 62 FT SLOOP 1938 Designer Nicholas Potter Length Engine Yanmar 4JH3THE 96hp 40 ft 0 in / 12.2 m Builder Wilmington Boat Works waterline Location France Date 1938 Beam 13 ft 2 in / 4.02 m Price EUR 500,000 Length overall 62 ft 0 in / 18.9 m Draft 8 ft 4 in / 2.55 m Length deck 62 ft 0 in / 18.9 m Displacement 21 Tonnes Double mahogany over cedar on oak Construction frames These details are provisional and may be amended Specification BROKER'S COMMENTS There is a reason Nick Potter's yacht designs are so special. Among his peers he had the best mentors possible: Starling Burgess, Nathaniel Herreshoff, L Francis Herreshoff, Frank Paine and Norman L. Skene. It's little wonder that his yachts are famously fast and stunningly beautiful, none more so than SERENADE: designed for arguably the greatest violinist of all time, Jascha Heifetz; with her exquisitely drawn-out canoe stern almost like a beautiful musical instrument. Such a striking, comfortable and practical yacht would always have been cherished, and under her most recent two ownerships SERENADE has received all the loving care an octogenarian demands. There may be a once in a lifetime opportunity to own such a special yacht. This is it. • SANDEM AN YACHT COMPANY • • Brokerage Of Classic & Vintage Yachts • www.sandemanyachtcompany.co.uk © Sandeman Yacht Company Limited 2021. A member of the ABYA. HERITAGE, VINTAGE AND CLASSIC YACHTS +44 (0)1202
[Show full text]
Kate Cory Instruction Book
Kate Cory_instructions.qxd 1/10/07 12:20 PM Page 1 INSTRUCTION MANUAL MODELING THE KATE CORY ! WHALING BRIG, 1856 ! Technical Characteristics Scale: 3/16" = 1 ft. Overall Length: 23-5/8"; Hull Length: 15-1/4" Width: 9-1/4" (width of fore lower yard, 13" with studding sails); Hull Beam: 4" Height: 19" (top of main mast to bottom of keel) Instructions prepared by Ben Lankford ©2007, Model Shipways, Inc. Manufactured by Model Shipways, Inc. • Hollywood, Florida Sold by Model Expo, a division of Model Shipways, Inc. • www.modelexpo-online.com Model Shipways Kit No. MS2031 Kate Cory_instructions.qxd 1/10/07 12:20 PM Page 2 HISTORYHISTORY Throughout the middle of the 19th century, activities in the Atlantic whale fishery were carried out in small fore-and-aft schooners and brigs. The latter are hermaphrodite brigs, or “half-brigs”, or simply “brigs” to use the jargon of laconic whalemen. Kate Cory was built in 1856 by Frank Sisson and Eli Allen in Westport Point, Massachusetts for Alexander H. Cory, one of the lead- ing merchants of that community. The ship was named after Alexander’s daughter. Registered at 132 tons net, Kate Cory was 75' 6" in length between perpendiculars, 9' 1-1/2" depth, and had a beam of 22' 1". The last large vessel to be built within the difficult confines of that port, she was also one of the last small whalers to be built specifically for her trade; most of the later whaling brigs and schooners were converted freighters or fishermen. While originally rigged as a schooner, Kate Cory was converted to a brig in 1858, this rig affording steadier motion in heavy seas or while cutting-in whales, not to mention saving much wear and costly repair to spars, sails and rigging.
[Show full text]
Noaa Ship Oscar Elton Sette Specification for Drydock Repairs Fy2021 Revison 1
NOAA Ship Oscar Sette FY21 Drydock Repairs May 2020 NOAA SHIP OSCAR ELTON SETTE SPECIFICATION FOR DRYDOCK REPAIRS FY2021 REVISON 1 1 NOAA Ship Oscar Sette FY21 Drydock Repairs May 2020 FY 2021 DRYDOCK REPAIRS for NOAA Ship Oscar Elton Sette TABLE OF CONTENTS DESCRIPTION/TITLE PAGE 1.0 SCOPE 2.0 GENERAL 3.0 BASE ITEMS 3.1 Temporary Services 3.2 ABS Intermediate Hull Survey 7 Inspection 3.3 Drydock & Routine Drydock Work 3.4 Propeller and Tailshaft Inspection and Repair 3.5 Underwater Hull Preservation and Coating 3.6 Bow Thruster Inspection and Service 3.7 Sea Valve Overhauls 3.8 Main Propulsion Motors Maintenance and Inspection 3.9 Dock and Sea Trials 3.10 Annual Liferaft Inspections 3.11 Ground Tackle Preservation and Anchor Windlass Overhaul 3.12 General Electric Systems Maintenance 3.13 Annual Fire Detection and Suppression Systems Inspection 3.14 0-1 Deck Soft Patch (BERP) Renewal 3.15 Bilge Valve Overhauls 3.16 Miscellaneous Piping Repairs 3.17 Air Receiver Visual and Hydrostatic Testing 3.18 Miscellaneous Steel Repairs 3.19 Sewage Holding Tank (2-20-0-W) Repairs and Painting 3.20 Motor Room Intake Vent Renewal 3.21 Auxiliary Sea Water (ASW) Pump Overhauls 3.22 Anti-Roll Tank Piping and Reach Rod Modifications 3.23 Steering System Maintenance 3.24 Gauge and Instrument Calibration 3.25 Ballast Water Treatment System Installation 3.26 Reverse Osmosis Installation 3.27 Radar Installation 3.28 Generation Room (3-34-0-E) Bilge Preservation 3.29 Propulsion Motor Room (3-60-0-E) Bilge Preservation 3.30 Hydraulic Hose Replacement 3.31 Annual
[Show full text]