Operating instructions WLAN Access Point 100 DATALIGHT®

Last modified: June 2017 DRAINAGE SYSTEMS ELECTRICAL SYSTEMS BUILDING TECHNOLOGY INDUSTRIAL PRODUCTS Future-proof networking

DATALIGHT® The easy and flexible network system

■ electrical conduit with integrated data cable ■ future-proof installation for satisfied customers ■ quick installation without extra effort and expense ■ innovative product for broadband installation in buildings ■ parallel installation of electric cables and 1 Gbps network cables Table of contents

1 Overview, licensing notes 4

2 Operating modes 5 – 7

3 Configuration 8 – 23

3.1 Password setting 8 3.2 System 9 3.2.1 General settings 9 3.2.2 Language 9 3.3 Status 10 3.4 Network 10 – 15 3.4.1 IP settings 10 – 11 3.4.2 WLAN setting 11 – 14 3.4.3 Diagnostics 15 3.5 System – backups / updates 15 – 16 3.5.1 Backup / update 15 3.5.2 Firmware update 15 3.5.3 System reboot 16 3.5.4 Log-out 16 3.6 Reset 16 – 17 3.6.1 Reset variants 16 3.6.2 Reset in the event of malfunction 17 3.6.3 Reset to factory settings / loading firmware in the event of a malfunction 17 3.6.4 Meaning of the LEDs 17 3.7 Expert information 18 3.7.1 LAN expert charts 18 3.7.2 WLAN expert charts 18 3.7.3 Controlling the WLAN AP via UDP 18 3.8 Services 19 – 21 3.8.1 Time switch function for LAN / WLAN 19 Future-proof networking 3.8.2 Remote control 20 3.8.3 Guest interface setup 21 3.8.4 Configuring guest connections 21 DATALIGHT® 3.9 Technical information 22 – 23 The easy and flexible network system 3.9.1 Transmission power range 22 3.9.2 Factory settings 23 ■ electrical conduit with integrated data cable ■ future-proof installation for satisfied customers 4 with malfunctions 24 ■ quick installation without extra effort and expense ■ innovative product for broadband 5 Glossary 25 – 26 installation in buildings ■ parallel installation of electric cables and 6 Your connection to us 27 1 Gbps network cables

FRÄNKISCHE | 3 OI WLAN Access Point 100 DATALIGHT® 1 Overview

Each device includes various instruc- Do not use the device for any other pur- The WLAN AP is connected to the inter- tions/information for the following areas: pose. Only operate it in interior spaces. nal data network via polymer optical fibres (POF). n installation (with technical data) These operating instructions apply only n license to devices equipped with firmware - The WLAN range can be adapted to the n operation sion 2.x to 4.x (see following figure). room conditions and it can be limited to the room. This creates powerful room Please categorically note radio cells which ensure maximum the instructions for all General information radio bandwidth within the room while three areas – in particular at the same operating with low the safety instructions pro- The WLAN AP offers an excellent alter- power consumption and low radiation. ! vided with the installation native to comply with the requirements Due to its low energy consumption and instructions enclosed with of modern network infrastructures thus low radio emissions, demarcation the devices. according to DIN 18015-2 and RAL-RG problems among individual access 678 without having to refrain from the points, over-coupling of WLAN sections flexible use of modern, mobile technolo- and compromised data rates are largely Intended use gies such as tablet PCs or laptops and avoided. without restricting wireless data rates. The wireless access point (WLAN AP) The WLAN AP can also be controlled has different operating modes and func- In addition, the WLAN AP works like a directly via UDP and features extensive tions. It can, among other things, be normal data socket with a RJ45 outlet time switching and additional protocol used as access point for devices com- for a conventional data terminal (data functions. municating wireless or as a repeater to rate of 100 Mbps). Power is supplied increase the range of the wireless net- directly via 230 V on the rear side of the It is the first wireless access point world- work. device. wide to fit in a commercial installation box and also matches all design pro- It can also be connected to devices grammes of renowned switch manufac- which have no own WLAN adapter. turers.

System requirements

n LAN connection via POF cable n firmware 2.x and higher n PC/laptop/tablet with internet browser

1 Licensing notes

Parts of the firmware are subject to the License information Availability of the source code GNU General Public License. This product includes software by third Upon request, we will send you the parties under the terms of the GNU complete source code of the software General Public License. licensed under GNU General Public License – including all scripts to control You can use, change or distribute this the compilation and installation of the free software under the terms of the drivers. The complete license details can GNU General Public License. be found in a separate document.

4 FRÄNKISCHE | OI WLAN Access Point 100 DATALIGHT® 2 Operating modes

The WLAN AP acts as an interface This is due to the general physical prin- know the automatically assigned IP between the WLAN, connected data ter- ciples of wireless transmission and no address of the WLAN AP or of other minals and network cabling in the net- separate property of the WLAN AP. devices, and further programming/ work. Different operating parameters changes of settings can therefore must be set depending on the operating The following descriptions assume a become difficult. mode. Please refer to the following manual assignment of the IP addresses examples for general explanations. of the devices. In such cases you may use a WLAN net- work monitor such as “FING” to learn Please note that the maximum data When using a router with DHCP about the IP addresses of the WLAN rates in the operating modes with server function, IP address assignment AP(s). repeater function are generally halved can also be made automatically in the with each additional repetition! network. Please note that you do not

Operating mode I WLAN AP Router WLAN AP at the router, input via termination Internet Internet connection of terminal devices ☁ in the house via the WLAN and RJ45 socket Mode: access point SSID: free selection n  hard-wired network connection IP: 192.168.X.X via POF Encryption: free selection n interface to LAN/internet n m ode: access point Channel: 1–13

Duplex Fibre DATALIGHT® Patch cable

Operating mode II WLAN AP

Several WLAN AP at the switch Router Switch (radial, termination) Internet Mode: access point SSID: free selection Operation of several WLAN AP ☁ IP: 192.168.X.X via one switch Encryption: free selection n hard-wired network connection via Channel: 1–13 POF n interface to LAN/internet n mo de: access point

WLAN AP

Mode: access point free selection/ SSID: roaming IP: 192.168.X.X

Encryption: free selection

Channel: 1–13

to WLAN AP

Duplex Fibre DATALIGHT® Patch cable

FRÄNKISCHE | 5 OI WLAN Access Point 100 DATALIGHT® 2 Operating modes

Operating mode III WLAN AP base station WLAN AP client (ESSID) (ESSID and BSSID) (ESSID)

Bridge/repeater

Connection of two network segments Printer via WLAN Mode: access point Mode: client (WDS) (WDS) n  SSID: from base station increase in the range of SSID: free selection wireless-enabled devices IP: 192.168.X.X IP: 192.168.X.X Printer n interface to LAN/internet Encryption: from base station Encryption: free selection n mo de: Channel: from base station base station: a ccess point Channel: 1–13 (WDS/repeater) Mode: virtual AP client: client (WDS) free selection SSID: or roaming Router IP: automatic Internet Encryp- free selection tion: or roaming Channel: automatic ☁Duplex Fibre DATALIGHT® Patch cable

Operating mode IV WLAN AP client (ESSID and BSSID) (ESSID) Router Repeater, range expansion via/of the (ESSID) WLAN network Mode: access point SSID: free selection

Connection of terminal devices to a IP: 192.168.X.X Internet Mode: client relayed WLAN router Encryption: free selection SSID: from base station Channel: 1–13 n increase in the range of ☁ IP: 192.168.X.X wireless-enabled devices Encryption: from base station n interface to LAN/internet Channel: from base station n mo de: client: client relayed Mode: virtual AP free selection SSID: We cannot guarantee compatibility with or roaming all manufacturers on the market in this IP: 192.168.X.X operating mode. Applicable manufac- Encryp- free selection tion: or roaming turers' instructions must be observed. Channel: automatic Duplex Fibre DATALIGHT® Patch cable

Operating mode V WLAN AP WLAN AP Mode: client (WDS) base station client SSID: from base station Mode: access point IP: 192.168.X.X Roaming via repeater SSID: free selection Encryp- IP: 192.168.X.X from base station Free movement within the WLAN tion: without new login Encryption: free selection Channel: from base station Channel: 1–13 Mode: virtual AP Increase in the range of Router free selection SSID: wireless-enabled devices or roaming WLAN AP Mode: client (WDS) client IP: 192.168.X.X SSID: from base station n interface to LAN/internet Encryp- free selection Internet IP: 192.168.X.X tion: or roaming Applicable to all WLAN devices: Encryption: from base station Channel: automatic n same SSID ☁ Channel: from base station n same encryption, same Mode: virtual AP IP range free selection SSID: or roaming n mo de: IP: 192.168.X.X Duplex Fibre base station: access point free selection DATALIGHT® Encryption: or roaming (WDS/repeater) Patch cable client: client (WDS) Channel: automatic

6 FRÄNKISCHE | OI WLAN Access Point 100 DATALIGHT® 2 Operating modes

Operating mode VI Room 3

Roaming via termination Free movement within the WLAN WLAN AP without new login access point (ESSID 2) only Multi-room use of the Mode: access point internet via WLAN possible n interface to LAN/internet n same SSID for client and base station (room 1 and 2) ~ n different SSID for room 3 ~ n same encryption in all

rooms Room 2 n same range for IP address for client and base station

(room 1 and 2) WLAN AP n mode: client access point: access point (ESSID 1) client (WDS) base station: access point with virtual access point – (WDS/repeater) Mode: see also operat- client: client (WDS) ing modes IV and VII

Room 1

Router

Internet access point Mode: (WDS) SSID: free selection ☁ WLAN AP IP: 192.168.X.X base station (ESSID 1) Encryption: free selection Channel: 1–13

Operating mode VII WLAN AP Router Guest access Internet Internet access via WLAN ☁ Guest PC n shielding of the internal Mode: guest network SSID: automatic n number of guest depending IP: automatic on bandwidth Encryp- automatic n log function tion: n mode: guest Channel: automatic Mode: access point SSID: free selection IP: 192.168.X.X Encryption: free selection

Channel: 1–13 Duplex Fibre DATALIGHT®

Patch cable

FRÄNKISCHE | 7 OI WLAN Access Point 100 DATALIGHT® 3 Configuration

Make sure that the device 2. Enter the password (delivery condi- Individual configuration is properly connected. tion: admin) and log in. Please information in The device is delivered with factory set- ! the associated installation 3. If the initial configuration can only be tings and ready for operation. instructions. effected via WLAN, first search the WLAN AP via the wireless interface Using the web interface, you can config- of the device intended for commis- ure the WLAN AP and adapt it to your Initial configuration sioning (tablet PC, etc.). The WLAN requirements (e.g., language). Access is AP logs in to the network with the possible via patch cable, termination or We recommend making the initial config- “DATALIGHT” SSID. In the delivery WLAN. uration via one of the LAN interfaces of condition, the WLAN password is the device, e.g., via the front socket. To wireless123. We recommend adapting and/or check- do so, connect the LAN interface of ing the following: your PC with the WLAN AP. If you want to change the SSID, only use letters (without spaces or special char- n password In the delivery condition, the address of acters) and numbers. n device name the PC must be programmed n time zone in the 192.168.0.xxx range n language (x ≥ 0 ≤ 255, x ≠ 5!). Subnet mask: 255.255.255.0

1. S tart your web browser (e.g., Internet Explorer, Firefox, etc.) and enter http://192.168.0.5 in the address line.

If the web browser’s pop- up blocker is enabled, you must explicitly allow ! access via the respective dialogue.

3.1 Password setting

Go to “System/Administration” (Sys- tem/Administration) for password set- tings. Increase access protection by selecting an individual password. The password becomes visible when click- ing on the green arrows.

Only use letters (without spaces and special characters) and numbers.

Confirm the password and save it by clicking “Save & Apply” (Speichern & Anwenden).

8 FRÄNKISCHE | OI WLAN Access Point 100 DATALIGHT® 3 Configuration

3.2 System

The system settings are valid for all operating modes and can be changed in the “System” (System) tab.

3.2.1 General settings

To be able to recognise the WLAN AP in your network, enter an individual, unique name ("AC-WLAN" in as-deliv- ered condition). The name must start with a letter and must not contain any spaces. Invalid entries are marked in red.

As of V2.x, the devices are available in the network via this name (e.g., http://AC-WLAN without entering the IP address then also allows access to the device).

If necessary, change the default time You must reboot the device zone. You also have the option of syn- after changing the device chronising the time via different servers. name. Click "Reboot” (Neu ! Starten) and, in the window Click “Save & Apply” (Speichern & that opens, click “Reboot” Anwenden) to apply the changes. (Neustart durchführen). This will take about a minute.

3.2.2 Language

The user interface can be displayed in German or English. The “auto” setting assumes the current language of the internet browser.

“Save & Apply” (Speichern & Anwenden) applies this setting.

FRÄNKISCHE | 9 OI WLAN Access Point 100 DATALIGHT® 3 Configuration

3.3 Status

“Status” (Status) displays the current values of the system and the devices connected to the WLAN AP. This pro- vides you with, e.g., information on the channel and on logged-in stations for the configuration.

If several stations are logged in to a net- work, the WLAN AP automatically selects the one with the strongest sig- nal. A reception rate of 20 % should not be fallen below to ensure safe data transfer.

In addition to the access point model, you can also see the firmware version here.

3.4 Network

You can set the operating mode and additional configuration aspects in the “Network” (Netzwerk) tab under “IP set- tings” (IP-Einstellungen) or “WLAN” (WLAN). You can choose between four modes:

n access point (delivery state) n access point (WDS/repeater) n client (WDS) and n client (relayed)

3.4.1 IP settings The interface icons on the left mean: The IP settings (IP-Einstellungen) tab POF provides you with status information

regarding the LAN settings of your front connection WLAN AP. Run time, MAC address, transmitted /received data rate and the IP wireless address are displayed.

10 FRÄNKISCHE | OI WLAN Access Point 100 DATALIGHT® 3 Configuration

In addition to status information, you can click on “Settings” (Einstellungen) or “Edit” (Bearbeiten) to select the pro- tocol (static address or DHCP client), change the IP address and subnet mask of your WLAN AP, and enter the gate- way address and the DNS server of your router.

Click the “Use own DNS servers” (Benutze eigene DNS-Server) icon to add and save additional DNS servers.

3.4.2 WLAN setting

The WLAN status section provides you with an overview of the WLAN settings of your WLAN AP. It shows radio stand- ard, channel, bitrate, SSID, mode, BSSID, encryption, signal strength in per cent, logged-in stations with SSID, MAC address, IP address, signal and noise.

The “Scan” (Scan) field provides an overview of the nearby networks.

Select “Edit” (Bearbeiten) to make addi- tional settings of the gateway. “Disable” (Deaktivieren) disables the gateway, “Remove” (Entfernen) deletes it perma- In the WLAN settings, we differentiate between device configuration nently. and interface configuration.

Click “Add” (Hinzufügen) to add another gateway (e.g., necessary for repeater mode, see figure on the right).

FRÄNKISCHE | 11 OI WLAN Access Point 100 DATALIGHT® 3 Configuration

Device configuration – general settings

The following settings are possible:

n Enable/disable WLAN n Channel n Transmission performance (WLAN de-/aktivieren) (Kanal) (Sendeleistung) The WLAN interface can be disabled The frequency ranges of nearby By changing the transmission perfor- when not in use to avoid radiation channels overlap. You should there- mance, you can adjust the range of and to save energy. The other two fore select the channel such that the the WLAN AP to local conditions. It interfaces are still available. Switch- frequencies of other wireless devices should be kept rather small in accord- ing can also be implemented via UDP nearby do not overlap (e.g., radio ance with the area of application. (see page 18). microwave devices in the range of channels 9, 10). In Germany, 13 chan- nels are allowed, e.g., in the USA only 11. We thus recommend using the channels 1 to 11 only.

Interface configuration – general settings

The settings possible in interface configuration are network-specific:

n ESSID n Mode (Modus) n Hide ESSID (ESSID verstecken) Network name with which the WLAN Four modes are available: prevents unauthorized AP shall be connected. the operating modes Access Point, devices from seeing your network. Access Point (WDS/Repeater), Client (WDS) and Client (RELAYED) – see pages 5-7.

Click “Save & Apply” (Speichern & Anwenden) to apply the entries.

12 FRÄNKISCHE | OI WLAN Access Point 100 DATALIGHT® 3 Configuration

Relayed function / repeater mode

This requires firmware version 1.0.0.3 or is picked up, amplified and transmitted maximum data rates in the operating higher! as an access point at the place of instal- modes with repeater function are gener- lation of the WLAN AP. You can, e.g., ally halved with each further repetition! The relayed function forms the basis for “expand” WLAN connections at an This is due to the general physical prin- repeater functions. In this, an existing, existing router and/or make them more ciples of wireless transmission and no possibly weak WLAN signal of a router functionally reliable. Please note that the separate property of the WLAN AP.

WLAN AP WLAN AP Router 1. Tab: 1. Tab: Internet Relayed client Relayed client additional (Relayed additional (Relayed Client Client ☁ zusätzlich) zusätzlich) 2. Tab: 2. Tab: Access Point Access Point

1x repeated (50 %) 2 x repeated (25 %) Possible, not recommended

The operating mode as repeater and access point requires appropriate con- figuration in the WLAN AP. Since these are two different WLAN operating modes, they must also be configured and/or added under Network > WLAN (Netzwerk > WLAN). The first of the following figures shows the gateway settings.

FRÄNKISCHE | 13 OI WLAN Access Point 100 DATALIGHT® 3 Configuration

This gateway must feature the “Client (RELAYED)” operating mode. The IP address of the relayed client must be in the same address range as the router (or device to be amplified). The second gateway to be added is parametrized as access point (see lower illustration). In WLAN operation, mobile data terminals or other repeaters, which are set up sim- ilarly to the previous processes, are con- nected to this gateway.

Device configuration – advanced settings

You can make more settings in the respective tab of both device and inter- face configuration:

n Mode (Modus) In the delivery state, devices can log in according to the IEEE 802.11 b/g/n standard. If you want to restrict access, you can configure special radio standards.

n HT mode (HT-Modus) (only with 802.11g+n mode) In the n-standard, HT 20/40 can be selected. Check which bandwidth produces the best result.

Interface configuration – WLAN encryption

The WLAN encryption protects the net- n Key (Schlüssel) Click “Save & Apply" (Speichern & work from attacks by unauthorized By assigning the key, you grant Anwenden) to confirm and apply all set- users. access to your network to authorized tings made. users only. n Encryption (Verschlüsselung) The mode set in the delivery state is Change the key! considered to be the safest, however, When selecting the key, please observe some older devices do not support it the same criteria as for the selection of (avoid WEP!). the password, however, the password should comprise at least 20 characters n Cipher (Cipher) for encryption processes such as WPA Encryption procedure, “auto” in the and WPA2 for WLAN for security rea- delivery state. sons.

14 FRÄNKISCHE | OI WLAN Access Point 100 DATALIGHT® 3 Configuration

3.4.3 Diagnostics (Diagnosen)

Here you can test the network and internet connection. n Enter an internet address (internal or external). n Click “Ping request” (Ping-Anfrage). You will then receive information as to whether the data have been sent and the remote station has responded.

3.5 System – backups / updates

3.5.1 Backup / software update

For reasons of security, you can store Backup/restore Installing new firmware your individual settings on a PC and recover them from there. Select a backup folder on your PC where You can download the respective cur- you save the current settings. Click rent firmware from our homepage. Pro- A reset restores the WLAN AP to factory “Backup” (Sicherung erstellen). ceed as follows: settings (see page 16). A reset can be Click “Reset” (Reset durchführen) to carried out device-specifically as fol- restore the factory settings. (1) Save the file to your PC. lows: If you, e.g., want to install several WLAN AP with identical configuration, you can (2) If you want to keep the current con- n via web browser save the settings of a device as a backup figuration, confirm this. n by means of bridging at the device and then load this on the other devices. (3) Select the saved file (image).

(4) Click “Install” (Installieren).

3.5.2 Firmware update

Software backup Your configured programming is saved when you run a backup. This can be uploaded again if required. Alternative- ly, you can restore the factory settings.

Firmware update When updating the firm- ware from 1.x to the next higher version ! 2.x, no settings can be transferred.

In case of a “small” update – e.g. within version 1 or 2 – all the settings are maintained in the device after the update if you have ticked “Maintain con- figuration” (Konfiguration behalten).

FRÄNKISCHE | 15 OI WLAN Access Point 100 DATALIGHT® 3 Configuration

3.5.3 System reboot

A reboot achieves the following:

Adoption of the actions carried out under software update (see page 15).

3.5.4 Log-out

Exit the user interface of the WLAN AP using the “Logout” (Abmelden) tab.

Save you configurations beforehand. To make more changes (at a later point in time), you will need to log in with your password again.

3.6 Reset

3.6.1 Reset variants

A reset restores the WLAN AP to factory New device variants Loading factory settings settings (see page 17). A reset can be carried out as follows: From versions 2.x, you can either per- n Short-circuit the multi-pin connector form a reboot or load the factory set- socket or actuate the reed contact for n via web browser tings via the multi-pin connector socket more than 5 seconds and less than 10 (see 3.5.3) or via the reed contact – depending on seconds. how long the contact is actuated. n by means of bridging at the device The start of the reset is confirmed (for older versions, see page 17) Resetting with a flashing LAN LED.

n by means of a reset magnet n Short-circuit the multi-pin connector socket or actuate the reed contact for more than 2 seconds and less than 5 seconds.

The start of the reset is confirmed with a flashing WLAN LED (see page 17).

16 FRÄNKISCHE | OI WLAN Access Point 100 DATALIGHT® 3 Configuration

3.6.2 Reset in the event of malfunction

Devices with multi-pin connector socket: Create a bridge (e.g., with a paper clip) for a minimum of 5 and a maximum of 30 seconds during operation. The - tem starts with the factory settings.

Devices with a reed contact: Hold the reset magnet to the reed con- tact for at least 5 and a maximum of 30 seconds during operation (see figure). The system starts with the factory set- tings.

3.6.3 R eset to factory settings / loading firmware in the event of a malfunction

Proceed as follows to n Wait 5 seconds. Go to, e.g., "Win- 192.168.1.1 A ddress of the TFTP reset your WLAN AP to dows - Start - Run" and enter “cmd”. server in the WLAN factory settings if you no n Confirm with “OK”. AP ! longer have access to n Enter “tftp -i 192.168.1.1 put put Send data your WLAN AP: acw-rk- xxxx.bin” (see meaning). acw-rk-xxxx.bin F ile name (xxxx is, e.g., a version number De-energize the WLAN AP! Meaning of the entries: like 2000) must be in C:\ C hange to the root directory the root n The PC network card must be tftp S tart TFTP client (available in the same IP range! in the operating system) The system gives a feedback n Create a bridge at the device -i binary file transfer regarding successful data transfer. (see 3.6.2). n Turn the power back on.

3.6.4 Meaning of the LEDs

For detailed error analysis and commis- show the activity on the respective at the RJ45 port for diagnostic / function sioning, you can also use the state of ports (UAE socket and POF connector). display available: the green LEDs which can be seen with the cover removed from the upper With newer variants/versions of the n LED blue = WLAN component of the WLAN AP. They WLAN AP, there is an additional LED n LED orange = LAN n LED purple = WLAN/LAN active n flashing = data traffic

POF connection (fast flashing = no link, slow flashing = link)

LED indicator status

FRÄNKISCHE | 17 OI WLAN Access Point 100 DATALIGHT® 3 Configuration

3.7 Expert information

This will provide you with detailed infor- in the LAN and WLAN range which you mation about the current data transfer can use as an analysis tool.

3.7.1 LAN expert charts

You can use these charts to check whether a LAN connection exists and what data rates are transmitted incom- ing and outgoing in the period of 5 min- utes. The recording is performed as long as the associated window is open only.

3.7.2 WLAN expert charts

The WLAN charts provide you with information about the transmission qual- ity regarding signal, noise and data rate.

3.7.3 Controlling the WLAN AP via UDP

The WLAN interface of the device can Notes: To apply the entered UDP port, UDP commands be switched on and off via UDP com- you must reboot the WLAN AP. Click Commands Meaning mand. "Reboot” (Neu Starten) and, in the win- dow that opens, click “Reboot” (Neus- WLAN ON Turn on WLAN interface Enable the UDP function by entering the tart durchführen). Rebooting takes WLAN OFF Turn off WLAN interface desired port in the “System” (System) approximately one minute. WLAN ? Enquire state menu. No port is configured in the fac- tory settings. Afterwards, confirm the The UDP function will be available after- Please consider case-sensitivity when entry by clicking the “Save & Apply” wards. You can switch this off via making your entries. The WLAN AP (Speichern & Anwenden) button. WLAN (smartphone) but not back on. confirms a transmitted UDP command by returning the current state.

18 FRÄNKISCHE | OI WLAN Access Point 100 DATALIGHT® 3 Configuration

3.8 Services

3.8.1 Time switch function for LAN/ WLAN

The WLAN AP has an integrated, exten- sively definable time switch function. You can make the general settings in the first tab “Time switch function” (Zeitschaltfunktion): n WLAN and/or LAN on/off By clicking the green “on/off” (ein/ aus) button, you switch (for the respective network) between the two states ON and OFF. n Activate time switch (Zeitschaltuhr aktivieren) Here you can generally switch off the time switch (or switch it on). n LED indication (LED-Anzeige) Each of the changes made must be The LED indication is independent saved for adoption and application. of the time switch function and only reflects the status of the internal interface.

The second section “Time entries” (Zeiteinträge) allows you to configure the time switch individually. You can define one switching operation per line. Six predefined periods are offered to facilitate this: n Select the desired period (“When”) and enter the desired combination of time, day, date, WLAN/LAN validity.

We recommend generally defining the “contrary” switching operation (if required via “Add” (Hinzufügen)) in the respectively following line. Delete no longer required time entries with the respective command.

You can furthermore define holidays. n Enter the respective date in DD/MM/ YYYY . Switching on holidays If there are no weekend entries, nothing The time is continuously updated by the is treated as was defined for week- will happen on the configured holidays. second according to the settings under ends. “System > General settings” (System > n Click “Save & Apply” Allgemeine Einstellungen). (Speichern & Anwenden) to activate the switching times.

FRÄNKISCHE | 19 OI WLAN Access Point 100 DATALIGHT® 3 Configuration

3.8.2 Remote control (as of firmware 4.x)

As of version 4.x, the WLAN AP offers the possibility of centrally configuring other linked WLAN AP.

Proceed as follows under “Services > Remote control” (Dienste > Fernsteu- erung):

n Finding all devices in the network Click the green “Scan” (Scan) button. All connected WLAN AP (as of V 4.x) are listed including IP address, SSID, etc.

n Calling up device Click the respective “Edit” (Bearbe- iten) button to configure the device (see following screenshot).

Please use the MAC address, which is located on the rear ! side of the devices and which you should note down, to clearly assign the devices.

n Configuring device Configure the device as desired in the “System properties“ (Systemeigen- schaften), “Network settings” (Net- zwerkeinstellungen), “WLAN set- tings” (WLAN Einstellungen) subi- tems.

For a visual check whether you have selected the ‘cor- ! rect’ device, temporarily switch the state of the LED (N) and confirm this with the “Send” (Absenden) button.

n Configuring more devices The list of other devices (see above) is displayed after you have config- ured one device.

Previously configured devices are not displayed in the list for ! now. Click the “Scan” (Scan) button again if you want to configure these devices again.

20 FRÄNKISCHE | OI WLAN Access Point 100 DATALIGHT® 3 Configuration

3.8.3 Guest interface setup

The WLAN AP offers you the possibility of providing a guest access via WLAN.

The in-house LAN is not available to the guests here.

The “hosting” WLAN AP is the first device in the list (alphabetically). For the guest connections, you first need to add and configure a new interface via "Net- work > WLAN" (Netzwerk > WLAN): n General settings (Allgemeine Einstellungen) Assign a new ESSID. We recommend naming the device “Guest” in line with its function. You should abso- lutely define the Mode (Modus) as access point. n WLAN encryption Each of the changes made must be (WLAN-Verschlüsselung) saved for adoption and application by Configure an extra key for the guest clicking the green button. access (WLAN password).

3.8.4 Configuring guest connections

After setting up the guest interface, you can make the general configurations at “Services > Guest connections” (Dien- ste > Gast-Verbindungen) in the “Guest mode” (Gast Modus) section: n Activate connection (Verbindung aktivieren) Click to activate or deactivate the guest connection. n Delete guest protocol (Gast-Protokoll löschen) For reasons of data protection, you can only view but not save the guest protocol.

Each of the changes made must be saved for adoption and application by clicking the green button.

FRÄNKISCHE | 21 OI WLAN Access Point 100 DATALIGHT® 3 Configuration

“Status > Overview” (Status > Übersicht) provides you with information regard- ing the stations logged-in.

n Deactivating guest connection If you only deactivate the guest con- nection, then the WLAN gateway still exists in the device and can be reacti- vated later.

n Deactivating interface If you deactivate the WLAN of the guest interface, it is no longer availa- ble for use (internet access)!

n Removing interface The easiest way to remove the guest interface is via “Network > WLAN” (Netzwerk > WLAN).

Each of the changes made must be saved for adoption and application by clicking the green button.

3.9 Technical information

3.9.1 Transmission power range 49 % transmission power 100 % transmission power The transmission power range depends, among other things, on the structural in the front (in the room) in the front (in the room) infrastructure. Adapt the location of the WLAN AP to the structural envi- 40 metres 40 metres

ronment. The figure shows the recep- 30 30 tion power depending on the transmis- 20 20 sion power and the distance from the WLAN AP using the example of con- 10 10 crete walls. 0 0

in the back (in the wall) in the back (in the wall)

Legend

> –70 dBm reception possible

–60–70 dBm good to medium reception

0-60 dBm very good to good reception

22 FRÄNKISCHE | OI WLAN Access Point 100 DATALIGHT® 3 Configuration

3.9.2 Factory settings

Factory settings Own settings Own settings System/Administration:

Password admin

System/System:

Host name AC-WLAN

Language German

UDP port none

Network/LAN/settings:

Protocol static address

IPv4 address 192.168.0.5

IPv4 netmask 255.255.255.0

IPv4 gateway none

DNS server none

Network/WLAN/settings:

The WLAN network is activated yes

Channel auto

Transmission power 100 %

ESSID DATALIGHT®

Mode access point

Hide ESSID no

Network/WLAN/Advanced settings:

Mode auto

HT mode 20 MHz

Network/WLAN/Encryption:

Encryption WPA-PSK/WPA2-PSK Mixed Mode

Cipher auto

Key wireless123

Network/Diagnostics:

Ping none

LED:

LAN activated

WLAN activated

FRÄNKISCHE | 23 OI WLAN Access Point 100 DATALIGHT® 4 Help with malfunctions

Cause Action LEDs are off The WLAN AP is without supply voltage Switch on the supply voltage

LAN LED (orange) is off The LAN interface has been deactivated in the “Time switch function” (Zeitschaltfunktion) section or the LED display has been Activate deactivated function deactivated

WLAN LED (blue) flashes The WLAN interface has been deactivated in the “Time switch function” (Zeitschaltfuntkion) section or the LED display has been Activate deactivated function deactivated

No connection with the WLAN base station

The WLAN AP is beyond the range of the base station Reduce the distance between the devices

The WLAN function of your WLAN AP is deactivated Activate the WLAN function

Another WLAN network causes disturbances Switch to another channel or switch the channel to “auto”

The encryption of your WLAN AP has been set to “WEP” Configure the encryption to WPA/WPA2 in the user interface or “unencrypted“ (unverschlüsselt)

To establish a WEP connection, the ESSID must be “visible” (si- chtbar). Switch the ESSID to “visible” (sichtbar). After a connection The ESSID has been set as “hidden” (unsichtbar) has been established, you can switch the ESSID back to “hidden” (nicht sichtbar)

The WLAN AP and the PC use different encryption methods Configure the same encryption method at the PC and the WLAN AP

No WLAN connection with the PC Check whether the WLAN adaptor is switched on; some devices The WLAN adaptor of the PC is not ready for operation have a physical switch for this The PC is beyond the range of the WLAN AP Reduce the distance between the PC and the WLAN AP

The WLAN AP and the PC use different encryption methods Configure the same encryption method at the PC and the WLAN AP

No access to devices in the network possible The device has a firewall Grant network access to the firewall Wrong address range/wrong subnet mask Check if the addresses have been configured correctly

The WLAN AP cannot be found under the IP address You have activated the DHCP client Try to find the device using the WLAN function

The plain text view for password and key does not work Remove all activations in the compatibility view (Kompatibilität- You are using Internet Explorer 9 sansicht) under Extras/Settings (Extras/Einstellungen)

The diagrams are not displayed Install a SVG plugin (e.g., by Adobe at You are using Internet Explorer 7 or 8 http://www.chip.de/downloads/Adobe-SVG-Viewer_15272819.html)

Remove all activations in the compatibility view (Kompatibilität- You are using Internet Explorer 9 sansicht) under Extras/Settings (Extras/Einstellungen)

24 FRÄNKISCHE | OI WLAN Access Point 100 DATALIGHT® 5 Glossary

Meaning Abbreviation Function

Base station, interface for wireless communication, end devices are logged in at the access point via WLAN which is Access point AP connected to the network by cable, similar to bridges or switches, layer 2-based

Adaptor Connects a wired communication device with an AP via WLAN

Freely available encryption algorithm with 128, 192 or 256 bit key Advanced Encryption Standard AES length and 128 bit block size

Originates from the synchronisation of relevant parameters by Basic Service Set BSS several devices

Equals either the MAC address of the AP or is created randomly Basic Service Set Identifier BSSID and clearly identifies each BSS

Operating mode in which texts longer than the block cipher length Cipher can be encrypted (e.g., AES)

Connects a wired communication device with an AP via WLAN, Client also called repeater or WLAN adaptor DNS server Computer (server) carrying out name resolution Carries out the name resolution, i.e., implementation of a host Domain Name System DNS name into the associated IP address Extended Service Set ESS Combination of several WLAN radio cells into a larger one Connection of several APs into a network requires the same SSID, Extended Service Set Identifier ESSID which is called ESSID in this case

Larger bandwidths and thus larger speeds are possible in HT-40 mode. Range is reduced, speed advantage is only realistic to a High Throughput HT mode limited extent (IEEE-802.11-n devices required, ideal connection required)

Independent Basic Service Set IBSS IBSS is a closed network without connection to other networks

Fourth version of the internet protocol, 32-bit address in four IPv4 address blocks in decimals with 8 bit each, one value range from 0-255 and separated by periods (xxx.xxx.xxx.xxx)

Connects networks with different protocols with each other, de- IPv4 gateway fines the route to the internet

Division between network and address section of the IP address, IPv4 netmask computers are in the same network if the address section is the same (the bits of the netmask which equal “1”)

The available frequency range in the 2.4 GHz range is divided Channel into 14 channels for better exploitation, the first 13 are available in Europe

Local network with an expansion of 500 m max., predominantly Local Area Network LAN domestic area up to small companies Mode see pages 5 – 7 Polymer Optical Fibre POF Plastic optical fibre

Part of a network address to assign data packages between client Port and server. With UDP, the port number of the service is included which should receive the data

Protocol Software agreement for data transmission Reed contact Magnet contact to reset the device using a reset magnet Repeater Signal amplifier expanding the range

FRÄNKISCHE | 25 OI WLAN Access Point 100 DATALIGHT® 5 Glossary

Meaning Abbreviation Function Host name Name of the AP Password Access protection Key Roaming Taking the WLAN connection from one AP to the next

Transmission power Transmitted power of the AP, mostly specified in dBm Freely selectable name of a WLAN, up to 32 characters long, Service Set Identifier SSID configuration in the AP and all connected clients

Security protocol in the WLAN and other radio networks Temporal Key Integrity Protocol TKIP based on the IEEE-802.11 standard

Serial interface to transfer data – application Universal Serial Bus USB in the WLAN AP: USB 2.0

Simple, connection-free network protocol to transmit data. Ports User Datagram Protocol UDP are used to allocate the data to the correct applications

Encryption Provides security in data transmission WPA WLAN encryption algorithm Wi-Fi Protected Access Successor of WPA and based on AES according to the WPA2 IEEE 802.11 a,b,g,n WLAN standards Wired Equivalent Privacy WEP WLAN encryption algorithm

Process to address data frames, establishment of a radio network with several APs, WDS both with a WLAN interface (single radio WDS, connection to the AP and client), Wireless Distribution System WDS and several dual radio WDS, one interface to the AP and another to the client) can be realised at the AP, differentiation in bridging (2 WLAN bridges connected) and repeating mode (several APs connected via WDS)

Wireless Local Area Network WLAN Similar to LAN but wireless

26 FRÄNKISCHE | OI WLAN Access Point 100 DATALIGHT® 6 Your connection to us

In-house technical consulting

Bodo Schmidt Florian Wolf Phone +49 9525 88-2472 Phone +49 9525 88-2352 [email protected] [email protected]

Field service technical consulting

Thomas Schneider Florian Bürk Southern Germany Southwestern Germany Phone +49 9525 88 - 2779 Mobile +49 171 900 25 79 Mobile +49 171 379 71 68 [email protected] [email protected]

André Lüdecke Stephan Bode Western Germany Northern Germany Mobile +49 171 297 46 31 Mobile +49 160 885 44 20 [email protected] [email protected]

Technical service Visit our websites

Phone +49 9525 88-8123 www.fraenkische.com [email protected] www.datalight-system.com

All information in this publication generally reflects the state of the art at the time of printing. Furthermore, considerable care was taken when preparing this publication. Nevertheless, typesetting and translation errors cannot be entirely excluded. We also reserve the right to make changes to our products, specifications and other data. Changes may also become necessary as a result of legal, material-related or other technological requirements, which cannot or can no longer be considered in this publication. For this reason, we cannot assume any liability which is based solely on the data provided in this publication. The decisive role with regard to the data on products and services is always played by the order placed, the product actually purchased and the documentation in connec- tion with it, or the information provided by our specialist staff in each specific individual case.

FRÄNKISCHE | 27 OI WLAN Access Point 100 DATALIGHT® Subject to change without notice | Cat. no. 299.99.206 no. |Cat. notice without change to Subject Phone +49952588- 8123 |Fax +492151 952588- |[email protected] FRÄNKISCHE pro inplastics expertise and experience of years many our Both worldwide. We currently employ about people 4,200 applications. industrial and technology building electrical, drainage, for systems pipe corrugated superior technically of marketing and manufacturing design, inthe leader industry and enterprise oriented, medium-sized family-owned growth- innovative, an is FRÄNKISCHE Wels, Austria Romania Cluj, Istanbul, Turkey Italy Milan, Mönchaltorf, Switzerland Germany Hermsdorf, Germany Ebersbach/Fils, France Torcy-le-Grand, Spain Toledo, Yeles/ Russia Moscow, Britain Great St.-Leonards-on-Sea, Republic Czech Okříšky, Germany Schwarzheide, Bückeburg, Germany Königsberg, Germany (headquarters) Our facilities in Europe: successful! globally – Königsberg in Rooted Rohrwerke Gebr. Kirchner GmbH &Co. KG|HellingerStr. 1|97486 Königsberg/Germany

-

Pune, India Pune, Hangzhou, China China Anting/Shanghai, Our in facilities Asia: us to develop products and solutions solutions and products develop to us enables customers our to proximity The offices. sales and facilities production Today, we are globally represented with Kirchner. Otto by run now is and 1906 in established was that business owned family generation athird is FRÄNKISCHE customers. our by valued highly are products of array large the and services consulting our cessing, |www.fraenkische.com

Guanajuato, Mexico Guanajuato, USA Anderson, Mexico: and America North in facilities Our Morocco Casablanca, Tunisia Arous, Ben Our facilities in Africa: solutions. advanced technologically and ticated sophis for –Your partner FRÄNKISCHE products. our for requirements and needs their and customers our on focus philosophy business and action Our needs. tomers’ cus our to tailored perfectly are that - -

© www.istockphoto.com | www.fotolia.de