Installation Instructions - BMW F10 CarPlay MMI Prime
Installation and User Guide BMW F10
For the Carplay MMI Prime
BimmerTech FZE | Phone: +1(646) 439-7920 | www.bimmer-tech.net 1 Installation Instructions - BMW F10 CarPlay MMI Prime
BMW F10 1
Introduction 3
Kit contents 4
Recommended and useful tools 6
Setting up the DIP switches on the MMI 7
Installing the MMI 8
Installing the Microphone Adapter Harness 14
Operating the MMI 16
A little prep before pairing your phone 17
Unpairing your phone from iDrive Bluetooth 17
Setting up the #8 memory button 17
Pairing an iPhone 17
Wireless iPhone Pairing 18
Pairing an Android phone 20
Screen Mirroring 21
Installing the Front View Camera (FVC) 22
Installing the Rear View Camera (RVC) 29
Final setup 37
CarPlay for Right Hand Drive BMWs 37
Camera settings 37
Manual Transmission Vehicles 38
Alternative Setting for Select Automatic Transmission Vehicles 38
Park Distance Control (PDC) Settings 39
Dynamic Parking Lines 39
Full Screen Camera Mode 40
Reassembly 40
BimmerTech FZE | Phone: +1(646) 439-7920 | www.bimmer-tech.net 2 Installation Instructions - BMW F10 CarPlay MMI Prime
Introduction
Thank you for making a purchase from BimmerTech! The CarPlay retrofit is DIY friendly, but if you’re not fond of working on your car, don’t worry. You can always take your kit along with these installation instructions to one of our recommended installers: https://www.bimmer-tech.net/dealers or to any other professional installer in your area. If you will be handing the installation over to a shop from outside our recommended list ideally it should specialize in BMW vehicles.
If you will be installing the kit by yourself then it is recommended to do so in a clean, spacious, well lit and climate-controlled garage without pressing time constraints. It’s also possible to perform the installation in a driveway or a parking lot if you prepare the correct tools and the weather is appropriate.
Installation requires disassembly of various trim pieces, so it’s best to take your time, be gentle, careful and diligent in keeping track of which screw and clip came from where in order to reinstall the parts correctly. Make sure to test the device's operation before final reassembly.
Please read the instructions before starting the installation. Also, make sure to have a look at the below installation videos.
The first one shows our CarPlay MMI Prime being installed in a 3-Series BMW. https://www.youtube.com/watch?v=IdmmySum1Sc
The second video shows a completely different generation of MMI being installed in a 3-Series BMW which offers great insights into trim disassembly/reassembly respective to front and rear camera installations. https://www.youtube.com/watch?v=SksfQZnKILg
This manual contains information on how to install the CarPlay MMI Prime and Front & Rear Cameras. If you will not be installing cameras simply omit the respective installation steps.
BimmerTech FZE | Phone: +1(646) 439-7920 | www.bimmer-tech.net 3 Installation Instructions - BMW F10 CarPlay MMI Prime
Kit contents
● MMI WCPAA-BM12 ● Plug and Play Harness ● USB/AV Harness ● LVDS (LCD) Video Output Cable ● WiFi Antenna ● Microphone Harness
BimmerTech FZE | Phone: +1(646) 439-7920 | www.bimmer-tech.net 4 Installation Instructions - BMW F10 CarPlay MMI Prime
Rear View Camera + Extension Cable (optional)
Front View Camera + Extension Cable (optional)
BimmerTech FZE | Phone: +1(646) 439-7920 | www.bimmer-tech.net 5 Installation Instructions - BMW F10 CarPlay MMI Prime
Recommended and useful tools
● BimmerTech Trim Tool Kit (Highly Recommended) ● T-20, T-25, and T-30 Bits ● Phillips Head Screwdriver ● Electrical Tape ● Zip Ties ● Pliers ● 8mm and 10mm Socket and Ratchet ● 3mm Allen Key ● Double Sided Mounting Tape (Recommended) ● Sturdy Wire or Thin Hanger for Feeding wire ● Flashlight
BimmerTech FZE | Phone: +1(646) 439-7920 | www.bimmer-tech.net 6 Installation Instructions - BMW F10 CarPlay MMI Prime
Setting up the DIP switches on the MMI
The Multi Media Interface (MMI) included in your kit is the piece equipment that allows to transfer additional video signals different from the original iDrive view onto your BMW's factory screen. In order for the MMI module to work correctly the little DIP switches on the side of the MMI module will have to be set up according to your vehicles specification.
Important Note: Every time you change DIP switch settings make sure to disconnect the MMI modules POWER connector for 10 seconds. This will allow the new DIP switch settings to take effect. After that you can reconnect the power cable.
DIP switch 1: Always ON
DIP switch 2: Always ON
DIP switch 3:
DIP switch 3 is responsible for correct cooperation between the MMI module and your factory screen, ensuring that the image is displayed correctly with our device being connected between the original head unit and screen.
For big 10.2” and 8.8” panoramic screens set 3 to ON
For the smaller 16:9 aspect ratio 6.5” screens set 3 to OFF
DIP switches 4-8: Default OFF
Remember to disconnect the MMI from power after changing the DIP switch setup.
BimmerTech FZE | Phone: +1(646) 439-7920 | www.bimmer-tech.net 7 Installation Instructions - BMW F10 CarPlay MMI Prime
Installing the MMI
Begin the installation by disconnecting the negative battery terminal of the car battery to reduce the risk of damage to electrical components:
BimmerTech FZE | Phone: +1(646) 439-7920 | www.bimmer-tech.net 8 Installation Instructions - BMW F10 CarPlay MMI Prime
Head Unit Removal
Remove the trim surrounding the factory vents using a trim tool, being careful to not scratch any components. To do this, gently slide one of your trim tools under the trim, and slowly pry up as you make your way across the top and bottom of the trim. Be especially careful when working with the right hand side of the trim, as it is very thin.
BimmerTech FZE | Phone: +1(646) 439-7920 | www.bimmer-tech.net 9 Installation Instructions - BMW F10 CarPlay MMI Prime
BimmerTech FZE | Phone: +1(646) 439-7920 | www.bimmer-tech.net 10 Installation Instructions - BMW F10 CarPlay MMI Prime
Important Note: If your head unit is larger than the one in the above picture you can install the MMI module in a space between the glove box and head unit as shown in the following video: https://www.youtube.com/watch?v=7h_b8z7qxGk
To remove the iDrive screen:
BimmerTech FZE | Phone: +1(646) 439-7920 | www.bimmer-tech.net 11 Installation Instructions - BMW F10 CarPlay MMI Prime
Once the iDrive screen is out, gently disconnect the factory video cable from the back of the screen by pressing on the connectors securing tab and pulling the connector out. Next, route it towards the MMI’s final installation location and connect it (original cable) to the L CD IN socket of the MMI unit.
Connect the LCD cable supplied with the kit to the back of the original screen (90 degree angle connector). Feed the other end of the supplied LCD cable towards the MMI and plug the straight (180 degree) connector into the LCD OUT socket of the MMI unit.
Connect the supplied USB/AV harness to the connector on the MMI labeled “ AV/USB” and route the socket to an accessible location, as it will be used for connecting a USB cable to your phone, a USB stick for video/music files, or a future MMI software update.
The USB cable socket can be placed inside the glovebox or more commonly routed out of the dashboard through the area where the carpet joins with the center console on the passenger side. Then, it can be tucked under the trim (between the trim and carpet) so that it ends up being hidden yet still accessible.
BimmerTech FZE | Phone: +1(646) 439-7920 | www.bimmer-tech.net 12 Installation Instructions - BMW F10 CarPlay MMI Prime
While routing the USB cable along this path you may also run the cable ending with a 90 degree 3.5mm minijack right along it and connect it to the AUX port inside the armrest. WIthout this cable being connected to the AUX port you will not be able to hear any CarPlay audio.
Connect the Power plug from the P&P harness to the MMI where it is labeled “P ower”.
Connect the included WIFI antenna to the threaded round port on the MMI. You can experiment with the antenna location - just make sure to place it in a location where it is not surrounded or touching any metal brackets. As a rule of thumb, the closer the antenna is located to the phone the better. In general it’s reception is very good and will tend to work even if your phone is outside of the car.
BimmerTech FZE | Phone: +1(646) 439-7920 | www.bimmer-tech.net 13 Installation Instructions - BMW F10 CarPlay MMI Prime
Next, we’ll need to work in the Head Unit area: Remove the large square harness (Quadlock) from the back of the head unit by pressing on the center tab of the latch and pulling it back. Once the latch is pressed and pulled back, the square connector will begin to slide out.
Please, move the fiber optic cable from the factory quadlock (if you have one in the original quadlock as not all vehicles do) by unfastening the securing tab and pulling the Fiber Optic cable out. The cable will not resist being removed if the securing latch is gently lifted. Reinsert it in the PnP harnesses quadlock in the same spot.
Once the Fiber Optic Cable has been moved to the new harness, plug in the square harness into the back of the head unit at one end and to the harness coming out of the dashboard at the other.
Please see video below for fiber optic rewiring:
BimmerTech FZE | Phone: +1(646) 439-7920 | www.bimmer-tech.net 14 Installation Instructions - BMW F10 CarPlay MMI Prime
Installing the Microphone Adapter Harness
Finally you’ll be left with the adapter harness for the microphone which is shaped like the letter Y. It has a socket and a plug near each other on one side and a single 3.5mm mini jack plug at the other.
The end with a mini jack plug needs to be attached to the respective socket on the the PnP Harness.
Disconnect the original microphone in the headliner and attach it to the plug. Attach the plug which you disconnected from the microphone to the other socket of the Y harness.
The adaptor harness will need to be routed through the dashboard, towards the A-Pillar and upwards through the A-Pillar all the way to the factory microphone. Ensure the harness is placed behind the airbag. Do not disconnect any wiring from the airbag when working in the area. The original microphone pops out of the headliner with the help of a trim tool.
Drop the plastic area shown below, by removing the two 10mm nuts, as pictured below. Once the nuts are removed, use a trim tool to gently pry down and pop the remaining clips. Run the wires towards the A-Pillar being careful not to interfere with the airbag.
BimmerTech FZE | Phone: +1(646) 439-7920 | www.bimmer-tech.net 15 Installation Instructions - BMW F10 CarPlay MMI Prime
The cover on the side of the dashboard which is visible with an open door can be popped right out with the use of a trim too.
BimmerTech FZE | Phone: +1(646) 439-7920 | www.bimmer-tech.net 16 Installation Instructions - BMW F10 CarPlay MMI Prime
Operating the MMI
The MMI allows to greatly expand the functionality of the original iDrive system with:
● Apple CarPlay ● Android Auto ● USB Media Playback ● Apple AirPlay and Android AutoLink Mirroring ● Front and Reversing Cameras with Dynamic Parking Lines and PDC Sensor Display
To enter the main MMI menu press and hold the iDrive controller MENU button for 3s until the MMI menu appears on the screen or press the #8 radio memory button for about 1s.
If you’ve just started the car it may take a few moments for the MMI to boot up. To navigate within the MMI’s menu and CarPlay/Android Auto mode you can use the iDrive controller knob & BACK button or the scroll knob on the steering wheel along with the Voice Command and Phone Handle buttons.
The iOS and Android icons in the main menu will only be filled out with color when a phone is paired to the MMI in either CarPlay or Android Auto mode. Otherwise they will remain in a black and white color scheme.
To exit CarPlay and go back to the MMI’s Main Menu press the BACK button twice in quick succession (just like a double click on a mouse).
To switch navigate back to iDrive press and hold the iDrive Controller MENU button.
Long pressing the iDrive controller BACK button will cause the MMI to reboot.
To engage Front Camera Mode for an indefinite period of time press and hold the iDrive Controller “OPTION” button for 2 seconds. To exit the camera mode press and hold the iDrive BACK button.
BimmerTech FZE | Phone: +1(646) 439-7920 | www.bimmer-tech.net 17 Installation Instructions - BMW F10 CarPlay MMI Prime
A little prep before pairing your phone
(Applies to both iPhone and Android phone users)
Unpairing your phone from iDrive Bluetooth Before you start the pairing process make sure to delete your BMW’s bluetooth connection from your Phone and also delete your Phone from your BMW’s bluetooth connections menu.This will let the MMI handle both media and phone calls.
Setting up the #8 memory button In the car's iDrive menu go to Multimedia -> External Devices -> AUX and simply highlight it (do not click on AUX). Once highlighted press and hold #8 on the face plate of your radio for approximately 6 seconds until the button is memorized as a shortcut for AUX. This will let you switch both the audio source to AUX and video source to the MMI as the #8 also works as a shortcut for the MMI feed. It’s simply the quickest and most convenient way to do that.
You can review the process here: https://youtu.be/Cb824SWT1MM?t=824
Pairing an iPhone
Once you’ve installed all of the hardware and reconnected the battery you can pair your iPhone with CarPlay. We highly recommend carrying out the initial pairing via a cable connection for best results.
Enabling Siri
In order for the CarPlay to work with your phone Siri has to be enabled. Go to Settings -> Siri & Search and toggle on the Siri functions if you don’t have them on yet. You’ll be guided through a short set up process.
BimmerTech FZE | Phone: +1(646) 439-7920 | www.bimmer-tech.net 18 Installation Instructions - BMW F10 CarPlay MMI Prime
Initial pairing
To establish a wired CarPlay connection with the MMI connect an original Apple cable between the iPhone's Lightning port and the USB socket on the MMI’s harness. Non-original cables are not recommended - oftentimes they do not work at all, so make sure to use an Apple certified cable.
Once the cable is connected you’ll need to confirm a few requests on your iPhone and you’ll be set. When the connection has been established please try playing music from your iPhone via CarPlay mode to verify whether you have your AUX port input selected and set up correctly. If you can hear the music at a comparable volume to FM radio that means you’re set up fine. If the volume is too low you can increase the AUX ports input volume. In general level 0 should be fine - it simply means there is no additional volume boost on the AUX input.
If you find it to be necessary you can also adjust the 8-band Equalizer in the MMI Audio menu.
After making sure audio playback works fine you can check the microphone reception when in CarPlay mode. Press and hold the Voice Command button on your steering wheel until you hear a chime and see the Siri screen on your BMW’s screen. State your command of choice to check whether Siri is hearing your voice as indicated by the waveform moving at the bottom of the screen and if an answer is provided through your speakers, then you’re set.
Wireless iPhone Pairing
It’s also possible to pair an iPhone wirelessly; however, we still recommend doing the initial set up via cable, as it’s a way to ensure a reliable connection.
First, make sure you have Siri enabled in your phone to allow CarPlay operation. If Siri is toggled off CarPlay will not be accessible.
You will need to reboot your phone next.
To pair wirelessly go to Settings -> Wireless Devices -> Wireless CarPlay Pairing.
BimmerTech FZE | Phone: +1(646) 439-7920 | www.bimmer-tech.net 19 Installation Instructions - BMW F10 CarPlay MMI Prime
To connect an iPhone for the first time go to your iPhone’s Settings -> Bluetooth and wait a few seconds to allow the iPhone to discover the MMI’s Bluetooth network called CarPlayMMI:
Once the CarPlayMMI appears on the Bluetooth list, press the Start Search button in the MMI menu. As soon as your iPhone appears on the list you can stop the search by pressing down on the iDrive controller again. Then scroll down to highlight your iPhone’s name on the list and press the iDrive controller to confirm the connection.
Wait around 10 seconds for a couple of confirmation messages to start appearing on your iPhone and confirm them. Once you confirm all of the iPhone's requests, CarPlay will connect wirelessly every time you start your car. Just give it some time to boot up when doing a cold start.
BimmerTech FZE | Phone: +1(646) 439-7920 | www.bimmer-tech.net 20 Installation Instructions - BMW F10 CarPlay MMI Prime
Pairing an Android phone
Begin by restarting your Android phone.
To pair your Android phone in Android Auto mode you must first download and install the Android Auto app. Android Auto should initially be set up via a wired USB connection between a phone and MMI’s USB port. Make sure to use a high-quality USB cable, as not all of them are created equal and some may simply not work at all. In such a case, try a different USB cable. Turn on your Bluetooth and Wifi connection, but make sure you are not connected to any device.
Once the cable is connected you’ll need to confirm a few requests on your phone and you’ll be set. You can navigate the menus using the iDrive controller knob and the right steering wheel scroll wheel.
To move from the top portion of the Android Auto menu to the bottom menu strip press the iDrive controller BACK button. This is the only way to enter the lower menu. Keep in mind, if you do not see a specific app in the selection menu you can still access it on your phone and simply click play within the app.
Once the connection has been established try playing music from your phone via Android Auto mode to verify whether you have your AUX port input selected and set up correctly. If you can hear the music at a comparable volume to the FM radio that means you’re set up fine. If the volume is too low you can increase the AUX ports input volume. In general level 0 should be fine - it simply means there is no additional volume boost on the AUX input.
If you find it necessary you can adjust the 8-band Equalizer in the MMI Audio menu.
After making sure audio playback works well check the microphone reception when in Android Auto mode. If you have Google Assistant enabled on your Android Phone you can now communicate hands free in your car. You can either say “Hey Google” and give a command, or long press (around 2 seconds) the Voice Command button on your steering wheel until you hear a chime. State your command of choice. If Google Assistant registers your voice it will be indicated by the colored dots moving around at the top of the screen and an answer provided through your speakers. If it works, then you’re set.
Wireless Android Auto is available for supported devices, make sure you find and enable “Wireless Projection” within the app. After setting up the wired connection, wait at least 2 minutes for the phone to completely sync up and learn the device’s name for both Wifi and Bluetooth. Afterward, simply disconnect the USB cable from your phone.
Next, go to Settings -> Wireless Devices -> Paired Devices. Your phone will be displayed as “Connected” in blue. Highlight it and press the iDrive controller wheel down to disconnect your phone. The status will change to “Disconnected”. Wait 5 seconds. Then press the iDrive controller wheel down again. This will change the status back to "Connected" in Blue. Wait 15-45 seconds and now your phone will work wirelessly, provided it is capable of wireless projection and the options for wireless projection has been enabled in the Android Auto App.
BimmerTech FZE | Phone: +1(646) 439-7920 | www.bimmer-tech.net 21 Installation Instructions - BMW F10 CarPlay MMI Prime
Screen Mirroring
The MMI is capable of screen mirroring both iPhones and Android phones alike. Whenever you start up the mirroring function in the MMI Prime your iPhone or Android phone will be disconnected from CarPlay/Android Auto. iPhone users can mirror their screen via the built in apple Screen Mirroring function which is accessible by swiping up on the iPhone screen and selecting the MMI from the list of available mirroring receivers.
Android phones will require a wired connection and the A utolink app being installed on your phone.
BimmerTech FZE | Phone: +1(646) 439-7920 | www.bimmer-tech.net 22 Installation Instructions - BMW F10 CarPlay MMI Prime
Installing the Front View Camera (FVC)
Once again the F30 video installation guide will offer you invaluable information on front camera installation process: https://youtu.be/SksfQZnKILg?t=11m57s
Drop the plastic area shown below by removing the two 10mm nuts, as pictured below. Once the nuts are removed, use a trim tool to gently pry down and pop the remaining clips. Run the wires under the plastic by the foot well of the driver’s seat, being careful not to interfere with the airbag.
Remove the three 10mm plastic bolts. Turn these 90 degrees counter clockwise to release. Pull off the plastic panel to expose the firewall and the grommet that we will be drilling through.
The simplest and most efficient way to route the Front View Camera wire through the firewall is to drill a hole in the existing grommet, as shown below. Be sure to drill a large enough hole (yellow dot), so that the plastic clip will easily fit through, while being extremely careful not to make contact with any other wires.
Once you’ve drilled through the grommet, use a sturdy wire or a thin hanger to route the wire through the grommet.
Please remember the battery must be disconnected – we don't want fans to turn on while you're working with your hands under the hood.
BimmerTech FZE | Phone: +1(646) 439-7920 | www.bimmer-tech.net 23 Installation Instructions - BMW F10 CarPlay MMI Prime
BimmerTech FZE | Phone: +1(646) 439-7920 | www.bimmer-tech.net 24 Installation Instructions - BMW F10 CarPlay MMI Prime
Route the camera cable around the engine bay all the way to the rubber grommet in the firewall as space permits, and proceed to run it up to the MMI module, connecting it via the camera connecting cable to the FRONT video input and also connect the camera power connector to the appropriate power socket with yellow and black wires on the PnP harness.
Make sure the front camera picture is unobstructed by the grille and not upside down.
To engage Front Camera Mode for an indefinite period of time press and hold the iDrive Controller “OPTION” button for 2 seconds. To exit camera mode press and hold the iDrive BACK button.
You can also set up Front Camera to engage automatically when changing from Reverse to Drive gear in automatic transmission vehicles for a set period of time between 0 (disabled) and 15 seconds in Camera Settings Menu.
BimmerTech FZE | Phone: +1(646) 439-7920 | www.bimmer-tech.net 25 Installation Instructions - BMW F10 CarPlay MMI Prime
If the camera works as designed you can now secure the camera cable with cable ties to prevent it from moving around. After the cable is in its final location seal the hole you made in the grommet with black silicone.
If your vehicle has a mesh grille, simply unscrew the camera and install it through the grille mesh from the inside and screw it back together. Then connect the camera to the extension cable and heat shrink the connection. You should be able to do this without removing the bumper cover if you first remove one of the kidney grilles for easy access. A more than firm pull on the grille might be necessary for the clips to release the grille from the bumper. On some models of cars it’s easier than others. Do not use excessive force to pull off the grille but some force is required to release it from the bumper.
Some mesh grilles might require the use of a dremel tool to trim the grille ever so slightly to allow the installation of the camera. Be sure not to trim too much. Confirm the camera works and heat up the heat shrink carefully making sure not to disconnect the connectors inside. The heat shrink has thermal glue inside which has very good moisture isolation properties but is also really hard to remove if you make a mistake.
If you do not have a mesh grill and need to remove the front bumper panel:
BimmerTech FZE | Phone: +1(646) 439-7920 | www.bimmer-tech.net 26 Installation Instructions - BMW F10 CarPlay MMI Prime
You will need to lift the vehicle using a vehicle hoist:
To remove the front bumper panel:
BimmerTech FZE | Phone: +1(646) 439-7920 | www.bimmer-tech.net 27 Installation Instructions - BMW F10 CarPlay MMI Prime
BimmerTech FZE | Phone: +1(646) 439-7920 | www.bimmer-tech.net 28 Installation Instructions - BMW F10 CarPlay MMI Prime
BimmerTech FZE | Phone: +1(646) 439-7920 | www.bimmer-tech.net 29 Installation Instructions - BMW F10 CarPlay MMI Prime
Installing the Rear View Camera (RVC)
Attached are instructions how to take apart the trunk lid. You have to replace the factory trunk handle with a new handle that includes the camera (in the process move the switch mounted on a bit of plastic from your original trunk handle to the new one) and then run the camera cable all the way to the dashboard under various trim pieces, through the rear seats and under the door sills.
A coat hanger feeder wire will come in handy during this part of the installation. Then connect the yellow RCA cable from the rear camera extension cable to the yellow RCA socket marked (REAR) in the PnP harness and also connect the rear camera power connector to the appropriate power socket with yellow and black wires on the PnP harness. There are two of them to choose from.
BimmerTech FZE | Phone: +1(646) 439-7920 | www.bimmer-tech.net 30 Installation Instructions - BMW F10 CarPlay MMI Prime
BimmerTech FZE | Phone: +1(646) 439-7920 | www.bimmer-tech.net 31 Installation Instructions - BMW F10 CarPlay MMI Prime
Once you have removed the original trunk opening handle it will be necessary to pop the trunk opening switch off of it using a trim tool. Clip this switch onto the camera delivered with our kit - it should fit perfectly.
BimmerTech FZE | Phone: +1(646) 439-7920 | www.bimmer-tech.net 32 Installation Instructions - BMW F10 CarPlay MMI Prime
Original trunk handle with the switch installed:
Original trunk handle with the switch removed:
BimmerTech Trunk handle with the OEM switch clipped in:
Please remember to reattach the cable to the switch before reassembling the trunk trim.
BimmerTech FZE | Phone: +1(646) 439-7920 | www.bimmer-tech.net 33 Installation Instructions - BMW F10 CarPlay MMI Prime
BimmerTech FZE | Phone: +1(646) 439-7920 | www.bimmer-tech.net 34 Installation Instructions - BMW F10 CarPlay MMI Prime
BimmerTech FZE | Phone: +1(646) 439-7920 | www.bimmer-tech.net 35 Installation Instructions - BMW F10 CarPlay MMI Prime
BimmerTech FZE | Phone: +1(646) 439-7920 | www.bimmer-tech.net 36 Installation Instructions - BMW F10 CarPlay MMI Prime
BimmerTech FZE | Phone: +1(646) 439-7920 | www.bimmer-tech.net 37 Installation Instructions - BMW F10 CarPlay MMI Prime
Final setup
CarPlay for Right Hand Drive BMWs
In the settings menu you can toggle CarPlay to RHD mode which will move the sidebar closer to the driver. After changing the setting you’ll need to reboot the MMI by pressing and holding the BACK button for around 5s. Once the MMI boots up again CarPlay should be in RHD mode.
Camera settings
If you are installing a reversing camera along with the MMI set Reverse Camera to Aftermarket. If you won’t be installing a reversing camera or your car already has a reversing camera set it to Original.
BimmerTech FZE | Phone: +1(646) 439-7920 | www.bimmer-tech.net 38 Installation Instructions - BMW F10 CarPlay MMI Prime
Manual Transmission Vehicles
If your car has a manual gearbox toggle to yes.
Alternative Setting for Select Automatic Transmission Vehicles
In some cases, even though the Reverse Camera has been set to Aftermarket and the Manual Gearbox has been set to no the reverse camera will still not fire up correctly. In such a case, it may be necessary to toggle the Reverse Camera Alternative setting to on:
BimmerTech FZE | Phone: +1(646) 439-7920 | www.bimmer-tech.net 39 Installation Instructions - BMW F10 CarPlay MMI Prime
Park Distance Control (PDC) Settings
If your Vehicle is equipped with rear and/or front PDC sensors you can adjust the settings accordingly:
Dynamic Parking Lines
To enable Dynamic Parking Lines toggle the switch to yes:
BimmerTech FZE | Phone: +1(646) 439-7920 | www.bimmer-tech.net 40 Installation Instructions - BMW F10 CarPlay MMI Prime
Full Screen Camera Mode
In BMWs with 8.8” or 10.2” panoramic screens it is possible to make the cameras display in full screen mode. Once the setting is toggled to ‘on’ it will be necessary to disconnect the MMI from power for 10 seconds. If you already have the MMI installed and sealed up you’ll need to t urn the car off, exit it and close all of the doors. Lock it with your key fob and then please take all keys out of the vehicle and at least 15m or 50ft away from the car and wait 10-15 minutes. This will put the car into a “sleep” mode which will also kill any power going to the MMI.
Reassembly
Carefully reinsert the head unit, be careful with the new harness and reinsert the securing screws. If you are having a hard time sliding the head unit back into place, then it most likely means that some cables behind the head unit are in the way and need to be adjusted.
If you have any other questions with regards to the installation or setup of your kit please contact our technical support team in reply to the instructions e-mail or directly to [email protected] including the last 7 characters of your vehicles VIN for easy order identification.
We hope you will enjoy the use of our CarPlay MMI Prime!
BimmerTech FZE | Phone: +1(646) 439-7920 | www.bimmer-tech.net 41 Installation Instructions - BMW F10 CarPlay MMI Prime
BimmerTech FZE | Phone: +1(646) 439-7920 | www.bimmer-tech.net 42