Diy Distortion Meter

Total Page:16

File Type:pdf, Size:1020Kb

Diy Distortion Meter HOWTO DIY DISTORTION METER BY ERIC RUSSELL Properly setting amplifier and processor gains can optimize the Sound Quality and/ or Sound Pressure Level of your car audio system. The best way to do this is with an oscilloscope. However, if you don’t have access to one, you can build a Do-It-Your- self Distortion Meter for around $30 with parts found at your local Radio Shack™. You’ll need a mini-amplified speaker and a couple of voltage dividers. These instruc- tions include schematics for building the voltage dividers along with diagrams on how to connect and use them with your mini-amplified speaker. NOTE: This article is a companion to “How to Properly Set Your Gains”. Search our Knowledge Base for Answer #46 or keywords “Gain Tutorial”. Parts List The below chart refers to seven items needed from your local Radio Shack™ store. The total cost for these components is around $30. Most of the parts needed are used to create two Volt- age Dividers; one to measure the source unit output voltage, and another to measure the amplifier output voltage. These are needed because the sensitivity of the mini amplified speaker is so low, it can easily be over-driven. These voltage dividers “drop” the signal down to a safe level so we can properly drive the mini amplified speaker. If you don’t have wire and heatshrink, the chart also references these part numbers. Part # Radio Shack Description Price 277-1008 Mini Amplified Speaker $14.99 274-0339 2PK Solder Type Phono Plug (RCA) $3.79 274-0288 2PK Solder Type 1/8” Mono Phone Plug $4.19 270-0356 2PK Fully Insulated 2” Alligator Clips $2.59 55049108 NTE EW110 1/8W Metal Resistor 100 Ohms 2% $1.09 55049129 NTE EW310 1/8W Metal Resistor 10K Ohms 2% $1.09 55049134 NTE EW410 1/8W Metal Resistor 100K Ohms 2% $1.09 SUB TOTAL $ 28.83 Optional Parts 55048778 HS-6 in 1/8” Heatshrink Tubing in Assorted Colors $2.20 278-1222 75-Ft. UL-Recognized Hookup Wire (20AWG) $7.99 SUB TOTAL $ 10.19 GRAND TOTAL $ 39.02 Mini Amplified Speaker Source Unit Voltage Divider Amplifier Voltage Divider Source Unit Voltage Divider The source unit voltage divider reduces the amplitude of the signal by 100:1 and can handle up to 10 Volts AC (most source units produce between 2V to 4V RMS). The resistors will be housed inside - Parts List • (1) RCA Jack • (1) 1/8” mini phone plug • (1) 10,000 Ohm, 1/8 Watt resistor • (1) 100 Ohm, 1/8 Watt resistor • Assorted 1/8” heat shrink tubing • 20” Red 20 AWG wire • 20” Black 20 AWG wire Assembly Instructions 1. Disassemble 1/8” plug and RCA jack. 3. Prepare and trim heat-shrink tubing to proper length. 4. Trim red and black 20 AWG wires to approximately 20” length. 6. Solder resistors in place and trim off excess leads. 9. Solder wire leads and reassemble RCA shell. Source Unit Voltage Divider SourcR1e Unit= 10k V Ohm,oltage 1/8 Divider Watt R2 = 100 Ohm, 1/8 Watt Sourc e Unit Voltage Divider R1 V in (+) R1 V out (+) V in (+) V out (+) R2 V in (–) R2 V out (–) V in (–) V out (–) RCA Jack 10K Ω Signal/Core 1/8” Phone Plug RCA Jack 10K Ω Signal/Core 1/8” Phone Plug Ground/Shield Ground/Shield 100 Ω 100 Ω Source Unit Voltage Divider Amplifier Voltage Divider The amplifier voltage divider reduces the amplitudeR1 of the signal by 1,000:1 and can handle up to 100 Volts AC (that’s a pair ofV Power in (+) T2500-1bdCP amplifiers Vconnected out (+) together in bd-SYNC mode). Like the previous method, the resistors will be housed inside the 1/8” phone plug shell, so careful preparation is needed. Test fitting the components priorR2 to soldering will ensure a proper fit. V in (–) V out (–) Parts List • (1) RCA Jack • (1) 1/8” mini phone plug • (1) 100,000 Ohm, 1/8 Watt resistor • (1) 100 Ohm, 1/8 Watt resistor RCA Jack 10K Ω • Assorted 1/8” heat shrink tubing Signal/Core 1/8” Phone Plug • 20” Red 20 AWG wire • 20” Black 20 AWG wire Assembly Instructions 1. Disassemble 1/8” plug and Alligator Clips. Ground/Shield 2. Test fit resistors in place (once soldered, they can be trimmed to size). 3. Prepare and trim heat-shrink tubing100 to proper Ω length. 4. Trim red and black 20 AWG wires to approximately 20” length. 5. Configure heat-shrink tubing and 1/8” phone shell in the order of assembly. 6. Solder resistors in place and trim off excess leads. 7. Position heat-shrink tubing in place and carefully heat with lighter to fit. 8. Prepare other end of harness by sliding Alligator Clip sleeves over wire ends. 9. Solder wire leads and reassemble Alligator Clips with protective sleeves. Amplifier Voltage Divider AmplierR1 = 100k Voltage Ohm, Divider 1/8 Watt SourcR2e Unit= 100 V oltageOhm, 1/8 Divider Watt R1 R1 V in (+) V out (+) V in (+) V out (+) R2 R2 V in (–) V out (–) V in (–) V out (–) 10K Ω RCA Jack Signal/Core 100K Ω 1/8” Phone Plug Signal/Core 1/8” Phone Plug (+) Alligator Clips Ground/Shield (–) Ground/Shield 100 Ω 100 Ω Amplier Voltage Divider R1 V in (+) V out (+) R2 V in (–) V out (–) 100K Ω Signal/Core 1/8” Phone Plug (+) Alligator Clips (–) Ground/Shield 100 Ω Source Units Source Unit Voltage Divider R IN L EXT RFX8350 DISP OPEN COMPACT DISC PLAYER WITH DIGITAL TUNER CD CHANGER CONTROLLER R SEAT VOL 9V COMPACT LOUD DIGITAL AUDIO AS MODE LO/DX SCAN RPT RDM DOWN DISC UP k PUSH BAND1 2 3 4 5 6 PS MUTE RadioShac MENU EAKER MINI AMPLIFIER • SP Source Unit Voltage Divider 1. Insert 1kHz @ 0dB test tone into CD Player.R IN L EXT RFX8350 DISP OPEN 2. Slowly increaseCOMPACT DISC PLAYER WITHvolume DIGITAL TUNER CD CHANGERuntil CONTROLLER “raspy” sound emits from speaker R SEAT VOL 9V COMPACT LOUD 3. Once youDIGITAL AUDI O determine the clipping point of the source unit, DO NOT adjust the source unit’s volume AS MODE LO/DX control until youSCAN RPT haveRDM DOWN completedDISC UP amplifier configuration(s)Amplifier Vbelow.oltage Divider k PUSH BAND1 2 3 4 5 6 PS MUTE RadioShac MENU I EAKER 4. Reconnect RCAs from source unit to amplifier system. N MINI AMPLIFIER • SP Source Unit Voltage Divider EXT R 9VIN Mono & Stereo Amplifiers L EXT RFX8350 DISP OPEN COMPACT DISC PLAYER WITH DIGITAL TUNER CD CHANGER CONTROLLER R SEAT VOL 9V COMPACT LOUD DIGITAL AUDIO RadioShack AS MINI AMPLIFIER • SPEAKER MODE LO/DX SCAN RPT RDM DOWN DISC UP k PUSH BAND1 2 3 4 5 6 PS MUTE RadioShac MENU Amplifier Voltage Divider MINI AMPLIFIER • SPEAKER IN EXT 9V Amplifier Voltage Divider RadioShack MINI AMPLIFIER • SPEAKER Amplifier Voltage Divider IN EXT IN 9V EXT 9V 1. Slowly increase amplifier GAIN until “raspy” sound emits from speaker. RadioShack MINI AMPLIFIER • SPEAKER 2. If testing a Stereo amplifier; repeat test on both amplifier channels. RadioShack 3. If testing a Mono amplifier; use either Speaker OutputsAmplifier “A” or V “B”oltage on amplifierDivider. MINI AMPLIFIER • SPEAKER IN EXT Amplifier In Bridged Mode 9V RadioShack Amplifier Voltage Divider MINI AMPLIFIER • SPEAKER IN EXT 9V RadioShack MINI AMPLIFIER • SPEAKER 1. Slowly increase GAIN on BOTH left/right channels equally until “raspy” sound emits from speaker. ©2012 Rockford Corporation, All Rights Reserved E.W.R. V1.1 05/18/2012.
Recommended publications
  • An Oscilloscope Correction Method for Vector-Corrected RF Measurements
    This article has been accepted for inclusion in a future issue of this journal. Content is final as presented, with the exception of pagination. IEEE TRANSACTIONS ON INSTRUMENTATION AND MEASUREMENT 1 An Oscilloscope Correction Method for Vector-Corrected RF Measurements Sebastian Gustafsson, Student Member, IEEE, Mattias Thorsell, Member, IEEE, Jörgen Stenarson, Member, IEEE, and Christian Fager, Member, IEEE Abstract— The transfer characteristics of the RF front-end circuit components. As these errors must be compensated for circuitry of a real-time oscilloscope (RTO) are not only frequency to achieve accurate signal sampling [4], several correction dependent and nonlinear with signal amplitude but also depen- techniques have been introduced [5], [6]. Other correction dent on the voltage range setting of the oscilloscope. A correction table in the frequency domain is proposed to account for the techniques have also been introduced [7]–[12], but they are additional gain and delay introduced when switching between only valid for sampling oscilloscopes. Previous research different voltage ranges. The table was extracted from the has focused on correction techniques for a certain set of measured data in which a continuous-wave signal source was instrument settings, e.g., a particular voltage range. Hence, connected to the oscilloscope ports, whereas the input power, the changing the settings would make the correction invalid. frequency, and voltage ranges were varied. The importance of the corrections is demonstrated by its use in an RTO-based two-port However, changing the range is desirable in some applications, vector-corrected measurement system. Measurements from the to fully utilize the voltage range of the ADC.
    [Show full text]
  • Future of Vector Network Analysis Dylan Williams and Nate Orloff Integrated Circuits Drive Wireless Communications
    Future of Vector Network Analysis Dylan Williams and Nate Orloff Integrated Circuits Drive Wireless Communications Application Frequency (GHz) 10 30 100 300 1000 100 10 Transit Frequency (GHz) Frequency Transit 1990 1995 2000 2005 2010 2015 2020 Year We Cannot Take the Integrated Circuit for Granted at mmWaves 2 Next 15 Years of Wireless Manufacturing by Country The United States still dominates mmWave manufacturing Enables $12.3T in Total Economic Growth (2020-2035) Communication Providers Want Speed of Fiber on Your Phone Millimeter-Waves are the Next Wireless Frontier Measurements and Calibrations Matter at mmWaves Before Calibration 64 QAM at 44 GHz After Calibration mmWave Measurement Challenge of our Era Not a Single RF Connector! On-Wafer IC and System-Level Test OTA System-Level Test Transistor models IC Test System-Level Test End-to-End Verification On-Wafer Connectorized Free-Space Goals for Vector Network Analysis in CTL Project Calibration Reference Planes On-Wafer and to OTA Test On-Wafer Measurements • Innovations in Calibration • Support Device Models to System-Level Test • State-Of-The-Art Instruments for US mmWave NR Manufacturers Vector Network Analysis • Platform for Traceable System-Level Tests Across CTL • Close the Connector-Less Gap mmWave Design Extremely Complex Accurate measurements are a must 80 80 GHz GHz 160 ~ GHz 240 GHz • Highly nonlinear operating states required for efficiency • Characterize, capture, control and reuse harmonics • Must maintain linearity On-Wafer Measurement the Only Way to Test ICs Yesterday
    [Show full text]
  • P50xxa Streamline Series Vector Network Analyzer 2/4-Port up to 53 Ghz
    P50xxA Streamline Series Vector Network Analyzer 2/4-port Up to 53 GHz. 2/4/6-port Up to 20 GHz Compact Form. Zero Compromise. P5000A/P5020A 9 kHz to 4.5 GHz P5001A/P5021A 9 kHz to 6.5 GHz P5002A/P5022A 9 kHz to 9 GHz P5003A/P5023A 9 kHz to 14 GHz P5004A/P5024A 9 kHz to 20 GHz P5005A/P5025A 100 kHz to 26.5 GHz P5006A/P5026A 100 kHz to 32 GHz P5007A/P5027A 100 kHz to 44 GHz P5008A/P5028A 100 kHz to 53 GHz Find us at www.keysight.com Page 1 Keysight P500xA and P502xA Streamline Series VNA The freedom of portable network analysis doesn’t have to mean a compromise in performance. The P50xxA Series brings high-end performance and flexibility to the portable Keysight Streamline Series. Gain confidence in your measurements with best-in-class performance offering fast, reliable, and repeatable results. Explore the complete characterization of your devices with a rich portfolio of software applications that transform the compact network analyzer into a complete RF measurement solution. The P50xxA Series, a member of Keysight’s Streamline Series offers the performance required for testing passive components, amplifiers, mixers or frequency converters. The vector network analyzer (VNA) provides best-in-class key specifications such as dynamic range, measurement speed, trace noise and temperature stability. Choose from 2- or 4-port models up to 53 GHz, or 2-, 4- or 6-port models up to 20 GHz. The VNA is packaged in a compact chassis and controlled by an external computer with powerful data processing capabilities and functionalities.
    [Show full text]
  • 10 Factors in Choosing a Basic Oscilloscope 10 Factors in Choosing a Basic Oscilloscope Contents Intro 1 2 3 4 5 6 7 8 9 10 11 Contact 2
    10 FACTORS IN CHOOSING A BASIC OSCILLOSCOPE 10 FACTORS IN CHOOSING A BASIC OSCILLOSCOPE CONTENTS INTRO 1 2 3 4 5 6 7 8 9 10 11 CONTACT 2 10 Factors in Choosing a Basic Oscilloscope There are several ways to navigate this interactive PDF document: Click on the table of contents (page 3) Basic oscilloscopes are used as windows into signals for troubleshooting Use the navigation at the top of each page to jump circuits or checking signal quality. They generally come with bandwidths to sections or use the page forward/back arrows from around 50 MHz to 200 MHz and are found in almost every design lab, Use the arrow keys on your keyboard education lab, service center and manufacturing cell. Use the scroll wheel on your mouse Whether you buy a new scope every month or every five years, this guide will Left click to move to the next page, right click to move to the previous page (in full-screen mode only) give you a quick overview of the key factors that determine the suitability of a Click on the icon ß to enlarge the image. basic oscilloscope to the job at hand. The digital storage oscilloscope Oscilloscopes are the basic tool for anyone designing, manufacturing or repairing electronic equipment. A digital storage oscilloscope (DSO, on which this guide concentrates) acquires and stores waveforms. The waveforms show a signal’s voltage and frequency, whether the signal is distorted, timing between signals, how much of a signal is noise, and much, much more. 10 FACTORS IN CHOOSING A BASIC OSCILLOSCOPE CONTENTS INTRO 1 2 3 4 5 6 7 8 9 10 11
    [Show full text]
  • Oscilloscope & Multimeter
    INSTRUCTION OVERVIEW FOR Oscilloscope & Multimeter Stock No.64573 Part No.O20M/3C IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY TO ENSURE THE SAFE AND EFFECTIVE USE OF THIS PRODUCT. GENERAL INFORMATION These instructions accompanying the product are the original instructions. This document is part of the product, keep it for the life of the product passing it on to any subsequent holder of the product. Read all these instructions before assembling, operating or maintaining this product. This manual has been compiled by Draper Tools describing the purpose for which the product has been designed, and contains all the necessary information to ensure its correct and safe use. By following all the general safety instructions contained in this manual, it will ensure both product and operator safety, together with longer life of the product itself. AlI photographs and drawings in this manual are supplied by Draper Tools to help illustrate the operation of the product. Whilst every effort has been made to ensure the accuracy of information contained in this manual, the Draper Tools policy of continuous improvement determines the right to make modifications without prior warning. 1. TITLE PAGE 1.1 INTRODUCTION: USER MANUAL FOR: OSCILLOSCOPE & MULTIMETER Stock no. 64573 Part no. O20M/3C 1.2 REVISIONS: Date first published March 2015 As our user manuals are continually updated, users should make sure that they use the very latest version. Downloads are available from: http://www.drapertools.com/b2c/b2cmanuals.pgm DRAPER TOOLS LIMITED WEBSITE: drapertools.com HURSLEY ROAD PRODUCT HELPLINE: +44 (0) 23 8049 4344 CHANDLER’S FORD GENERAL FAX: +44 (0) 23 8026 0784 EASTLEIGH HAMPSHIRE SO53 1YF UK 1.3 UNDERSTANDING THIS MANUALS SAFETY CONTENT: WARNING! Information that draws attention to the risk of injury or death.
    [Show full text]
  • “WW 2,873,387 United States Patent Rice Patented Feb
    Feb. 10, 1959 M. c. KIDD 2,873,387 CONTROLLABLE.‘ TRANSISTOR CLIPPING CIRCUIT Filed Dec. 17, '1956 INVENTOR. v MARSHALL [.KIDD “WW 2,873,387 United States Patent rice Patented Feb. 10, 1959. 2 tap 34 on a second source of energizing potential, here illustrated as a battery 30, through a load resistor 32. 2,873,387 The battery 30 has a ground tap 31 at an intermediate point thereon, and the variable tap 34 allows the ener CONTROLLABLE TRANSISTOR CLIPPING gizing potential supplied to the collector electrode 14 to cmcurr be varied from a positive to a negative value. Output Marshall vC. Kidd, Haddon Heights, N. J., assignor to signals are derived between an output terminal 36, which Radio Corporation of America, a corporation of Dela is connected directly to the collector electrode 14 of the ware ‘ ‘ transistor 16, and a ground terminal 37. One type of 10 clipped or limited output signal that is available at the Application December 17, 1956, Serial No. 628,807 output terminals 36 is illustrated by the waveform 38, 5 ‘Claims. (Cl. 307-885) and the manner in which it is derived is hereinafter de scribed. , In order to describe the operation of the circuit, as This invention relates to signal translating circuits and 15 sume that the variable tap 34 on the battery 30 is set more particularly to transistor circuits for limiting or so that a small positive voltage, negative, however, with clipping a translated signal; - respect to base electrode voltage, appears on the collector In many types of electronic equipment, such as tele electrode 14, and that a sine wave is applied to the input vision, radar, computer and like equipment, it may be terminal 10, as illustrated by the waveform 18.
    [Show full text]
  • Voltage and Power Measurements Fundamentals, Definitions, Products 60 Years of Competence in Voltage and Power Measurements
    Voltage and Power Measurements Fundamentals, Definitions, Products 60 Years of Competence in Voltage and Power Measurements RF measurements go hand in hand with the name of Rohde & Schwarz. This company was one of the founders of this discipline in the thirties and has ever since been strongly influencing it. Voltmeters and power meters have been an integral part of the company‘s product line right from the very early days and are setting stand- ards worldwide to this day. Rohde & Schwarz produces voltmeters and power meters for all relevant fre- quency bands and power classes cov- ering a wide range of applications. This brochure presents the current line of products and explains associated fundamentals and definitions. WF 40802-2 Contents RF Voltage and Power Measurements using Rohde & Schwarz Instruments 3 RF Millivoltmeters 6 Terminating Power Meters 7 Power Sensors for URV/NRV Family 8 Voltage Sensors for URV/NRV Family 9 Directional Power Meters 10 RMS/Peak Voltmeters 11 Application: PEP Measurement 12 Peak Power Sensors for Digital Mobile Radio 13 Fundamentals of RF Power Measurement 14 Definitions of Voltage and Power Measurements 34 References 38 2 Voltage and Power Measurements RF Voltage and Power Measurements The main quality characteristics of a parison with another instrument is The frequency range extends from DC voltmeter or power meter are high hampered by the effect of mismatch. to 40 GHz. Several sensors with differ- measurement accuracy and short Rohde & Schwarz resorts to a series of ent frequency and power ratings are measurement time. Both can be measures to ensure that the user can required to cover the entire measure- achieved through utmost care in the fully rely on the voltmeters and power ment range.
    [Show full text]
  • Lab 1 – Measurements of Frequency
    Physics of Music PHY103 Lab Manual Lab 1 – Measurements of Frequency EQUIPMENT and PREPARATION Part A: • Oscilloscopes (get 5 from teaching lab) • BK Precision function generators (get 5 from Thang or teaching lab) • Counter/timers (PASCO, 4 + 1 other) • Connectors and cables (BNC to BNC’s, banana plug pairs) connecting function/signal generators to oscilloscopes and speaker. • BNC to 2 leads • Adaptors: mike to BNC so that output of preamps can be looked at on oscilloscope. • BNC to banana adapters • BNC T- adapters • Oscilloscope probes • Pasco open speakers • Microphones, preamps, mic stands • Strobes (3) optional Warning: do not place speakers near oscilloscope screens as they can damage the CRT (cathode ray tube) screens. Note: The professor will attempt to have the equipment out and available for the labs. However the TAs/TIs should check that the equipment is ready to use, that every lab setup has all the necessary equipment. The TA/TIs should also be familiar with the lab and know how to troubleshoot the equipment. INTRODUCTION In this lab, we will be measuring the frequency of a signal using three different methods. The first method involves the use of the function generator. A function generator is an instrument that can produce sine, square, and triangular waves at a given frequency. The second method makes use of the oscilloscope. An oscilloscope is an instrument principally used to display signals as a function of time. The final method for measuring the frequency uses the counter/timer. A counter/timer is an instrument that can give a very accurate measurement of the frequency of a signal by counting each time a voltage crosses a particular value.
    [Show full text]
  • Tektronix Cookbook of Standard Audio Tests
    ( Copyright © 1975, Tektronix, Inc. AI! rig hts re served P ri nt ed· in U .S.A. ForeIg n and U .S.A. Products of Tektronix , Inc. are covered by Fore ign and U .S.A . Patents and /o r Patents Pending. Inform ation in thi s publi ca tion supersedes all previously published material. Specification and price c hange pr ivileges reserve d . TEKTRON I X, SCOPE-MOBILE, TELEOU IPMENT, and @ are registered trademarks of Tekt ro nix, Inc., P. O. Box 500, Beaverlon, Oregon 97077, Phone : (Area Code 503) 644-0161, TWX : 910-467-8708, Cabl e : TEKTRON IX. Overseas Di stributors in over 40 Counlries. 1 STANDARD AUDIO TESTS BY CLIFFORD SCHROCK ACKNOWLEDGEMENTS The author would like to thank Linley Gumm and Gordon Long for their excellent technical assistance in the prepara­ tion of this paper. In addition, I would like to thank Joyce Lekas for her editorial assistance and Jeanne Galick for the illustrations and layout. CONTENTS PRELIMINARY INFORMATION Test Setups ________________ page 2 Input- Output Load Matching ________ page 3 TESTS Power Output _______________ page 4 Frequency Response ____________ page 5 Harmonic Distortion _____________ page 7 Intermodulation Distortion __________ page 9 Distortion vs Output _____________ page 11 Power Bandwidth page 11 Damping Factor page 12 Signal to Noise Ratio page 12 Square Wave Response page 15 Crosstalk page 16 Sensitivity page 16 Transient Intermodulation Distortion page 17 SERVICING HINTS___________ page19 PRELIMINARY INFORMATION Maintaining a modern High-Fidelity-Stereo system to day requires much more than a "trained ear." The high specifications of receivers and amplifiers can only be maintained by performing some of the standard measure­ ments such as : 1.
    [Show full text]
  • The Oscilloscope and the Function Generator: Some Introductory Exercises for Students in the Advanced Labs
    The Oscilloscope and the Function Generator: Some introductory exercises for students in the advanced labs Introduction So many of the experiments in the advanced labs make use of oscilloscopes and function generators that it is useful to learn their general operation. Function generators are signal sources which provide a specifiable voltage applied over a specifiable time, such as a \sine wave" or \triangle wave" signal. These signals are used to control other apparatus to, for example, vary a magnetic field (superconductivity and NMR experiments) send a radioactive source back and forth (M¨ossbauer effect experiment), or act as a timing signal, i.e., \clock" (phase-sensitive detection experiment). Oscilloscopes are a type of signal analyzer|they show the experimenter a picture of the signal, usually in the form of a voltage versus time graph. The user can then study this picture to learn the amplitude, frequency, and overall shape of the signal which may depend on the physics being explored in the experiment. Both function generators and oscilloscopes are highly sophisticated and technologically mature devices. The oldest forms of them date back to the beginnings of electronic engineering, and their modern descendants are often digitally based, multifunction devices costing thousands of dollars. This collection of exercises is intended to get you started on some of the basics of operating 'scopes and generators, but it takes a good deal of experience to learn how to operate them well and take full advantage of their capabilities. Function generator basics Function generators, whether the old analog type or the newer digital type, have a few common features: A way to select a waveform type: sine, square, and triangle are most common, but some will • give ramps, pulses, \noise", or allow you to program a particular arbitrary shape.
    [Show full text]
  • Experiment No. 3 Oscilloscope and Function Generator
    Experiment No. 3 Oscilloscope and Function Generator An oscilloscope is a voltmeter that can measure a fast changing wave form. Wave forms A simple wave form is characterized by its period and amplitude. A function generator can generate different wave forms. 1 Part 1 of the experiment (together) Generate a square wave of frequency of 1.8 kHz with the function generator. Measure the amplitude and frequency with the Fluke DMM. Measure the amplitude and frequency with the oscilloscope. 2 The voltage amplitude has 2.4 divisions. Each division means 5.00 V. The amplitude is (5)(2.4) = 12.0 V. The Fluke reading was 11.2 V. The period (T) of the wave has 2.3 divisions. Each division means 250 s. The period is (2.3)(250 s) = 575 s. 1 1 f 1739 Hz The frequency of the wave = T 575 10 6 The Fluke reading was 1783 Hz The error is at least 0.05 divisions. The accuracy can be improved by displaying the wave form bigger. 3 Now, we have two amplitudes = 4.4 divisions. One amplitude = 2.2 divisions. Each division = 5.00 V. One amplitude = 11.0 V Fluke reading was 11.2 V T = 5.7 divisions. Each division = 100 s. T = 570 s. Frequency = 1754 Hz Fluke reading was 1783 Hz. It was always better to get a bigger display. 4 Part 2 of the experiment -Measuring signals from the DVD player. Next turn on the DVD Player and turn on the accessory device that is attached to the top of the DVD player.
    [Show full text]
  • Topaz Sr10 / Sr20 Stereo Receivers Top-Tips
    TOPAZ SR10 / SR20 STEREO RECEIVERS TOP-TIPS Incredible performance, connectivity and value for money… The most powerful amplifiers in the Topaz range are designed to on the back allow you to connect traditional sources such as be the heart of your separates hi-fi system. The SR10 offers a CD players and even Blu-ray players. Thanks to a high quality room-filling 85 watts per channel and is backed by a dedicated Wolfson DAC, the SR20 goes one step further and provides three subwoofer output as well as two sets of speaker outputs - so you additional digital audio inputs, allowing the connection of digital can listen in two rooms at once or bi-wire your main speakers for sources such as streamers, TVs or set top boxes. a true audiophile performance. The SR20 steps things up a notch The SR10 and SR20’s playback capabilities also include a built- by offering the same flexible connectivity, but with an even more in FM/AM tuner, giving you access to all of your favourite radio powerful 100 watts per channel, driving virtually any loudspeaker stations with ease. We only use pure audiophile components, including discreet However you listen to your music, the SR10 and SR20 have it amplifiers, full metal chassis’ and high-performance toroidal covered. They boast a built-in phono stage so you can instantly transformers. The Topaz SR10 and SR20 are a winning connect a turntable, and a direct front panel input for iPods, combination of power, connectivity and purity, putting far more smart phones or MP3 players.
    [Show full text]