DOCSLIB.ORG

Empirical Analysis of Pneumatic Tire Friction on Ice

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Empirical Analysis of Pneumatic Tire Friction on Ice Empirical Analysis of Pneumatic Tire Friction on Ice Troy Nigel Holley Thesis submitted to the Faculty of the Virginia Polytechnic Institute and State University in partial fulfillment of the requirements for the degree of Master of Science in Mechanical Engineering Corina Sandu Mehdi Ahmadian Saied Taheri September 14, 2010 Blacksburg, VA Keywords: Friction, Ice, Terramechanics, Tires Empirical Analysis of Pneumatic Tire Friction on Ice Troy Nigel Holley Abstract Pneumatic tire friction on ice is an under-researched area of tire mechanics. This study covers the design and analysis of a series of pneumatic tire tests on a flat-level ice road surface. The terramechanics rig of the Advanced Vehicle Dynamics Lab (AVDL) is a single-wheel test rig that allows for the experimental analysis of the forces and moments on a tire, providing directly the data for the drawbar pull of said tire, thus supporting the calculation of friction based on this data. This indoor testing apparatus allows for some degree of replication by helping to maintain test conditions and by imposing a desired tire slip; the normal load, camber angle, toe angle, and other testing configurations can also be pre-set, as required. Methods of and issues related to controlling the production of ice and maintaining the conditions of numerous factors for each trial run were also documented. The AVDL terramechanics rig allowed for the collection of data from tests that varied the tire tread, tire inflation pressure, normal load on the wheel, and the slip ratio of the moving tire. This empirical data was then analyzed through the statistical analysis program JMP 8 in order to determine which factors (or combination of factors) significantly influence pneumatic tire friction on ice. The analysis verified that the slip ratio had a significant effect on the observed coefficient of friction, which decreased as the slip ratio increased. The combinations of the slip ratio and inflation pressure and the slip ratio and tire setup also had a significant effect on the observed coefficient of friction. The tests appear to have validated the theory that the drawbar pull and the traction was higher for the tire with tread. Acknowledgements I’d like to thank several people that helped me over the course of this research and in completing my degree: Dr. Sandu for the chance to work at CVeSS and for the incredible opportunity to obtain a Master’s Degree in Mechanical Engineering from Virginia Tech. Adam Woodward for his work on obtaining the enclosure and alleviating the friction problems plaguing the rig, along with Colin, Heather, and Vivake from NASA. Ben Taylor for his continued support with the Terramechanics Rig and the software and responding to minor questions I had. Michael Craft for his help on modifying the crossbar and moving around literally tons of equipment and sand and assisting with some of the cleanup. Clemente Negode for his steel angle idea for the camber. Thanks to my good friend [and future doctor] Ozma for giving me moral support over the summer. Special thanks to the National Science Foundation for their support through the NSF Grant Opportunities for Academic Liaison with Industry (GOALI) grant and the Graduate School Recruiting Office for their support through the Powell Fellowship. And of course thanks, Ma, for constant checking to see how I was doing and making sure I was alright… iii Table of Contents 1 Introduction .......................................................................................................................... 1 1.1 Motivation of the Study.................................................................................................... 1 1.2 Research Objective ........................................................................................................... 2 1.3 Research Approach .......................................................................................................... 2 1.4 Thesis Outline .................................................................................................................. 3 2 Review of Literature ............................................................................................................ 4 2.1 Review of Literature: Test Methodology ......................................................................... 4 2.2 Combined Testing Parameters ....................................................................................... 11 2.3 Review of Literature: Data From Previous Tire on Ice Tests ........................................ 11 2.4 Review of Literature: Coefficient of Friction Models ................................................... 16 2.5 Review of Literature: Slip Ratio of Preceding Models .................................................. 28 3 Background of Pneumatic Tires: Tire Design & Mechanical Properties .......................... 30 3.1 Tire Nomenclature.......................................................................................................... 32 3.1.1 Tire Nomenclature: Tire Section Width ................................................................. 33 3.1.2 Tire Nomenclature: Aspect Ratio ........................................................................... 33 3.1.3 Tire Nomenclature: Maximum Load ...................................................................... 34 3.1.4 Tire Nomenclature: Construction Code Indicator ................................................... 34 3.1.5 Tire Nomenclature: Wheel Diameter ...................................................................... 35 3.1.6 Tire Nomenclature: Load Index .............................................................................. 35 iv 3.1.7 Tire Nomenclature: Speed Rating ........................................................................... 37 3.2 Tire Nomenclature.......................................................................................................... 39 3.3 Tire Construction............................................................................................................ 41 3.3.1 Tire Construction: Tread ......................................................................................... 43 3.3.2 Tire Construction: Belt ........................................................................................... 45 3.3.3 Tire Construction: Breaker & Carcass .................................................................... 45 3.3.4 Tire Construction: Bead Wire ................................................................................. 46 3.3.5 Tire Construction: Sidewall .................................................................................... 46 3.3.6 Tire Construction: Tire Casing, Shoulder, and Crown ........................................... 47 3.4 Tread Pattern Construction............................................................................................. 47 3.5 Chemical Composition of the Tire ................................................................................. 50 3.6 Effective Rolling Radius ................................................................................................ 51 3.7 Tire Friction on Various Surfaces .................................................................................. 52 4 Characteristics of Ice and Tire Friction on Ice ................................................................... 53 4.1 Water Layer Formation .................................................................................................. 54 4.2 Differences in the Formation of Ice ............................................................................... 55 4.3 Main Factors that Affect Tire Friction on Ice ................................................................ 55 5 Test Equipment .................................................................................................................. 57 5.1 Test Equipment: Terramechanics Rig ............................................................................ 57 5.1.1 Test Equipment: Terramechanics Rig: Enclosure Modifications ........................... 60 v 5.1.2 Test Equipment: Terramechanics Rig: Air Springs and Modifications .................. 61 5.2 Test Equipment: Kistler RoaDyn P650 Wheel Force Sensor ........................................ 67 5.3 Test Equipment: Terramechanics Rig Computers ......................................................... 70 5.4 Test Equipment: Motion Control Software and Hardware ............................................ 70 5.5 Test Equipment: Data Acquisition ................................................................................. 71 5.6 Test Equipment: Pressure Pad ........................................................................................ 73 5.7 Test Equipment: Ice-Making Equipment ....................................................................... 75 5.7.1 Test Equipment: Ice-Making Equipment: Creation of Ice Test Surface................. 78 6 Design of Experiment ........................................................................................................ 82 6.1 Design of Experiment: Main Experiment ...................................................................... 82 6.2 Design of Experiment: Test Procedure and Slip ............................................................ 91 7 Results and Discussion of Results ..................................................................................... 96 7.1 Results and Discussion of Results: Filtering the Data ..................................................
Load more

Recommended publications
  • 641-8633 Email: [email protected] GENERAL INFORMATION
    Canadian Price List 2016 (905) 641-8633 www.fcracetires.com email: [email protected] GENERAL INFORMATION No Warranty Due to the conditions under which they operate, Goodyear MAKES NO WARRANTY AND SPECIFICALLY DISCLAIMS ANY WARRANTY (INCLUDING ANY WARRANTY AS TO MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), EITHER EXPRESSED OR IMPLIED, with respect to Goodyear racing tires, tubes, safety spares or air containers and shall not be liable for any damages whatsoever including, without limitation, consequential or special damages, arising out of their use. Goodyear racing tires are designed and compounded solely for racing purposes and are not tested or labeled to meet FMVSS/ECE Regulations. It is therefore not only dangerous, but also illegal to sell for use or use race tires on public streets or highways. Pressure Recommendations Consult your Goodyear Racing Tire Distributor for specific recommendations for your local track. Tire changing should be done by trained personnel using proper tools and procedures. NEVER attempt to install and inflate a tire of one diameter on a rim or wheel of another diameter. All Goodyear racing tires are designed to be used on wheels or rims that are manufactured to Tire and Rim Association (T&RA) specifications and tolerances. Use of Goodyear racing tires on damaged or improper rims can cause the assembly to explode with force sufficient to cause injury or death. When inflating, always lock wheel on mounting machine or place in safety cage and use extension gauge and hose with clip on air chuck. STAND BACK. NEVER EXCEED 35 PSI TO SEAT BEADS. Tire Care Goodyear racing tires should not be stored near high temperatures, in direct sunlight, around welding areas, in overhead garage areas or around high-voltage electric motors.
    [Show full text]
  • Tire Test Data: Using MI for Product/Process Improvement
    Tire Test Data: Using MI for Product/Process Improvement Advances in acquiring, storing, and reporting measurements from equipment in the final finish department have created the ability for tire manufacturers to actively monitor their end product for statistically relevant trends that can point to upstream product, machine, and process issues. Today’s high-end testing equipment can collect increasing amounts of more accurate data in even faster cycle times than before. This is changing the requirements that manufacturers have for their data infor- mation systems. Historically, to evaluate a tire uniformity machine waveform metric like radial force variation it was sufficient to calculate and store basic measurements (like peak-to-peak and the magnitudes from the first few harmonics). Not only do these harmonics make the largest contributions to problems with the ride of the tire, but they are also traceable to established upstream causes in curing and tire assembly. Now, manufacturers are interested in much higher harmonics of a waveform, looking for additional improvements in curing and tire assembly and even potential improvements in component preparation. But while these advances have continued to provide a greater data volume for evaluation of product and process, analysis efforts have been concentrated on increasing available data and reporting production trends through the use of traditional tools like tabular / SPC (Statistical Process Control) graphic reports and spreadsheets. The consequence of this focus has not allowed tire manufacturing quality analysis to keep pace with Business Intelligence (BI) technology developed specifically for and proven effective by analysts in the retail and financial industries. This trend is reminiscent of the slow movement of computers to the factory floor following their introduction to the "top floor" financial departments of business and industry during the 1980s.
    [Show full text]
  • Catl-1922, February 2017
    CATL-1922, FEBRUARY 2017 DEFENSE LOGISTICS AGENCY (DLA) COLUMBUS COOPERATIVE TIRE QUALIFICATION PROGRAM (CTQP) COOPERATIVE APPROVED TIRE LIST (CATL) CATL-1922 FOR US GOVERNMENT PURCHASE OF: Non-Military: New & Retread Passenger Car Tires, Pursuit and Emergency High Speed Tires, Light Truck Tires, Truck/Bus Tires, & Off Road Severe Application Tires (ORSA) Military: Retread Light, Medium and Heavy Tactical Truck and Trailer Tires This CATL-1922, revised FEBRUARY 2017, replaces all previous versions. 1 CATL-1922, FEBRUARY 2017 COOPERATIVE APPROVED TIRE LIST (CATL) OF PRODUCTS QUALIFIED UNDER ASTM STANDARD F1922 AND SAE J2014 (FOR MILITARY RETREADS) AND ADMINISTRATIVE MANUAL CTQP-AM-1922 FOR TIRES, PNEUMATIC, VEHICULAR (HIGHWAY AND SPECIAL APPLICATIONS) (NEW AND RETREADED) The Tires Privatization Initiative (TPI), the predecessor to TSI, was established to comply with the 2005 Base Realignment and Closure (BRAC) statute. This statute required the disestablishment of the Department of Defense's wholesale supply, storage and distribution functions for tires. As a result, the Defense Logistics Agency (DLA) awarded the Tire Privatization Initiative (TPI) contracts to industry for privatized supply chain and materiel support of the government’s demand for aircraft and ground tires. TSI is the follow on contract and will provide tire support for the Air Force, Army, Coast Guard, Marines, Navy and Foreign Military Services (FMS). The TSI Program consists of the TSI Contractor, Science Applications International Corporation (SAIC) and multiple tire providers (manufacturers/dealers). The TSI Contractor will provide logistical support services, global demand planning and forecasting, order processing and fulfillment, purchasing (from government-directed sources/LTCs), finance and inventory management, CONUS storage and warehouse operations management, CONUS distribution and transportation, packaging, obsolescence management, data management, and customer support services.
    [Show full text]
  • Sprinter Operating Instructions É9065849205{ËÍ 9065849205
    Sprinter Operating Instructions É9065849205{ËÍ 9065849205 Order no. 6462 7539 13 Part no. 906 584 92 05 Edition MY 2015 MB Sprinter Symbols Vehicle distributor Publication details G WARNING Internet Warning notes make you aware of dangers In the USA: which could pose a threat to your health or Further information on Mercedes-Benz vehi- life, or to the health and life of others. Mercedes-Benz USA, LLC cles can be obtained on the Internet at One Mercedes Drive http://www.mercedes-benz.com H Environmental note Montvale, NJ 07645-0350 http://www.mbusa.com (USA only) Environmental notes provide you with infor- www.mbusa.com http://www.mercedes-benz.ca (Canada mation on environmentally aware actions or www.mbsprinterusa.com only) disposal. Customer Assistance Center: 1-877-762-8267 ! Notes on material damage alert you to Editorial office dangers that could lead to damage to your vehicle. In Canada: You are welcome to forward any queries or i suggestions you may have regarding this These symbols indicate useful instruc- Mercedes-Benz Canada, Inc. tions or further information that could be Operator's Manual to the technical documen- helpful to you. 98 Vanderhoof Avenue tation team at the address on the inside of the Toronto, ON M4G 4C9 front cover. X This symbol designates an instruc- © tion you must follow. www.mercedes-benz.ca Mercedes-Benz USA, LLC X Several consecutive symbols indi- Customer Relations Department: © Mercedes-Benz Canada, Inc. cate an instruction with several 1-800-387-0100 Mercedes-Benz USA, LLC and Mercedes- steps. Benz Canada Inc. are Daimler companies.
    [Show full text]
  • MICHELIN Truck Tires Service Manual
    MICHELIN MICHELIN® Truck Tire ® TRUCK TIRE SERVICE MANUAL SERVICE TIRE TRUCK Service Manual MICHELIN® Truck Tire Service Manual To learn more please contact your MICHELIN Sales Representative or visit www.michelintruck.com To order more books, please call Promotional Fulfillment Center 1-800-677-3322, Option #2 Monday through Friday, 9 a.m. to 5 p.m. Eastern Time United States Michelin North America, Inc. One Parkway South Greenville, SC • 29615 1-888-622-2306 Canada Michelin North America (Canada), Inc. 2500 Daniel Johnson, Suite 500 Laval, Quebec H7T 2P6 1-888-871-4444 Mexico Industrias Michelin, S.A. de C.V. Av. 5 de febrero No. 2113-A Fracc. Industrial Benito Juarez 7 6120, Querétaro, Qro. Mexico 011 52 442 296 1600 An Equal Opportunity Employer Copyright © 2011 Michelin North America, Inc. All rights reserved. The Michelin Man is a registered trademark owned by Michelin North America, Inc. MICHELIN® tires and tubes are subject to a continuous development program. Michelin North America, Inc. reserves the right to change product specifications at any time without notice or obligations. MWL40732 (05/11) Introduction Read this manual carefully — it is important for the SAFE operation and servicing of your tires. Michelin is dedicated and committed to the promotion of Safe Practices in the care and handling of all tires. This manual is in full compliance with the Occupational Safety and Health Administration (OSHA) Standard 1910.177 relative to the handling of single and multi-piece wheels. The purpose of this manual is to provide the MICHELIN® Truck Tire customer with useful information to help obtain maximum performance at minimum cost per mile.
    [Show full text]
  • Owner's Manual for the Vehicle. with a Quick Reference Guide for Your Convenience
    Owner's Manual for the Vehicle. With a quick reference guide for your convenience. BMW recommends Castrol 325i 325xi Congratulations, and thank you for choosing a BMW. Thorough familiarity with your vehicle will provide you with enhanced control and security when you drive it. We therefore have this request: Please take the time to read this Owner's Manual and familiarize yourself with the information that we have compiled for you before starting off in your new vehicle. It contains important data and instructions intended to assist you in gaining maximum use and satisfaction from the unique range of technical features on your BMW. The manual also contains information on care and maintenance designed to enhance operating safety and contribute to maintaining the value of your BMW throughout an extended service life. This Owner's Manual should be considered a permanent part of this vehicle. It should stay with the vehicle when sold to provide the next owner with important operating, safety and maintenance information. This manual is supplemented by a Service and Warranty Information Booklet (US models) or a Warranty and Service Guide Booklet (Canadian models). We recommend that you read this publication thoroughly. Your BMW is covered by the following warranties: – New Vehicle Limited Warranty – Limited Warranty Rust Perforation – Federal Emissions System Defect Warranty – Federal Emissions Performance Warranty – California Emission Control System Limited Warranty Detailed information about these warranties is listed in the Service and
    [Show full text]
  • TSM Rear Ag Tire Research Report
    Rear Ag Tire Research Report Fatima Correia Tire Stewardship Manitoba Student Research Rear Ag Tire Research Report Purpose of Study The purpose of the rear agriculture tire research was to determine the average life span of a farm tire so Tire Stewardship Manitoba (TSM) can use this information in consideration for setting appropriate eco-fees on these OTR (Off The Road) tires. Method of Study The research was done through OTR Recycling and Reliable Tire Recycling, by taking digital photos of a tire’s sidewall. The tire’s sidewall, will list information including the date and manufacturing plant code, implementation rating, ply rating, and a tire mould code. Each code was then entered into a Microsoft Excel spreadsheet to be reviewed and analyzed. The Agricultural Tire There are a few ways to separate an agricultural tire from other OTR tires. The ply rating that is listed on the tire should be a relatively lower number and should not exceed 12 ply, to stand as an agricultural tire. These tires have a smaller ply rating because they need to be significantly lighter, so no extra weight is applied to the farmer’s field and helps to prevent damage to the crop. 2 Rear Ag Tire Research Report Another way of identifying an agricultural tire is by examining the tread markings. The Agricultural tire will have more spaces between treads; this is so there will be less contact to the farmer’s field which prevents the soil from becoming compressed. Although this is a way of recognizing an Agricultural tire from other OTRs it is not the most accurate way to identify between tires.
    [Show full text]
  • Tire Code - Wikipedia Visited on 2/21/2017
    Tire code - Wikipedia Visited on 2/21/2017 Not logged in Talk Contributions Create account Log in Article Talk Read Edit View history Tire code From Wikipedia, the free encyclopedia Main page Contents This article includes inline citations, but they are not properly Featured content formatted. Please improve this article by correcting them. Current events (September 2014) (Learn how and when to remove this template Random article Donate to Wikipedia message) Wikipedia store Automobile tires are described by an alphanumeric tire code (in American English and Interaction Canadian English) or tyre code (in British English, Australian English and others), which is Help generally molded (or moulded) into the sidewall of the tire. This code specifies the dimensions of About Wikipedia the tire, and some of its key limitations, such as load-bearing ability, and maximum speed. Community portal Sometimes the inner sidewall contains information not included on the outer sidewall, and vice Recent changes Contact page versa. Tools The code has grown in complexity over the years, as is evident from the mix of S.I. and English What links here units, and ad-hoc extensions to lettering and numbering schemes. New automotive tires Related changes frequently have ratings for traction, treadwear, and temperature resistance (collectively known Upload file as The Uniform Tire Quality Grade (UTQG) ratings). Special pages Permanent link Most tires sizes are given using the ISO Metric sizing system. However, some pickup trucks and Page information SUVs use the
    [Show full text]
  • Tire - Wikipedia, the Free Encyclopedia
    Tire - Wikipedia, the free encyclopedia http://en.wikipedia.org/wiki/Tire Tire From Wikipedia, the free encyclopedia A tire (or tyre ) is a ring-shaped covering that fits around a wheel's rim to protect it and enable better vehicle performance. Most tires, such as those for automobiles and bicycles, provide traction between the vehicle and the road while providing a flexible cushion that absorbs shock. The materials of modern pneumatic tires are synthetic rubber, natural rubber, fabric and wire, along with carbon black and other chemical compounds. They consist of a tread and a body. The tread provides traction while the body provides containment for a quantity of compressed air. Before rubber was developed, the first versions of tires were simply bands of metal that fitted around wooden wheels to prevent wear and tear. Early rubber tires were solid (not pneumatic). Today, the majority of tires are pneumatic inflatable structures, comprising a doughnut-shaped body of cords and wires encased in rubber and generally filled with compressed air to form an inflatable cushion. Pneumatic tires are used on many types of vehicles, including cars, bicycles, motorcycles, trucks, earthmovers, and aircraft. Metal tires are still used on locomotives and railcars, and solid rubber (or Stacked and standing car tires other polymer) tires are still used in various non-automotive applications, such as some casters, carts, lawnmowers, and wheelbarrows. Contents 1 Etymology and spelling 2 History 3 Manufacturing 4 Components 5 Associated components 6 Construction types 7 Specifications 8 Performance characteristics 9 Markings 10 Vehicle applications 11 Sound and vibration characteristics 12 Regulatory bodies 13 Safety 14 Asymmetric tire 15 Other uses 16 See also 17 References 18 External links Etymology and spelling Historically, the proper spelling is "tire" and is of French origin, coming from the word tirer, to pull.
    [Show full text]
  • 2020 Canadian Price List
    2020 Canadian Price List Still proudly serving Canada's racers [email protected] (905)641-8633 www.fcracetires.com GENERAL INFORMATION No Warranty Due to the conditions under which they operate, Goodyear MAKES NO WARRANTY AND SPECIFICALLY DISCLAIMS ANY WARRANTY (INCLUDING ANY WARRANTY AS TO MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), EITHER EXPRESSED OR IMPLIED, with respect to Goodyear racing tires, tubes, safety spares or air containers and shall not be liable for any damages whatsoever including, without limitation, consequential or special damages, arising out of their use. Goodyear racing tires are designed and compounded solely for racing purposes and are not tested or labeled to meet FMVSS/ECE Regulations. It is therefore not only dangerous, but also illegal to sell for use or use race tires on public streets or highways. Pressure Recommendations Consult your Goodyear Racing Tire Distributor for specific recommendations for your local track. Tire changing should be done by trained personnel using proper tools and procedures. NEVER attempt to install and inflate a tire of one diameter on a rim or wheel of another diameter. All Goodyear racing tires are designed to be used on wheels or rims that are manufactured to Tire and Rim Association (T&RA) specifications and tolerances. Use of Goodyear racing tires on damaged or improper rims can cause the assembly to explode with force sufficient to cause injury or death. When inflating, always lock wheel on mounting machine or place in safety cage and use extension gauge and hose with clip on air chuck. STAND BACK. NEVER EXCEED 35 PSI TO SEAT BEADS.
    [Show full text]
  • Run Flat Tires Versus Conventional Tires
    Run flat tires versus conventional tires Citation for published version (APA): Veld, op het, I. B. A. (2006). Run flat tires versus conventional tires: an experimental comparison. (DCT rapporten; Vol. 2006.042). Technische Universiteit Eindhoven. Document status and date: Published: 01/01/2006 Document Version: Publisher’s PDF, also known as Version of Record (includes final page, issue and volume numbers) Please check the document version of this publication: • A submitted manuscript is the version of the article upon submission and before peer-review. There can be important differences between the submitted version and the official published version of record. People interested in the research are advised to contact the author for the final version of the publication, or visit the DOI to the publisher's website. • The final author version and the galley proof are versions of the publication after peer review. • The final published version features the final layout of the paper including the volume, issue and page numbers. Link to publication General rights Copyright and moral rights for the publications made accessible in the public portal are retained by the authors and/or other copyright owners and it is a condition of accessing publications that users recognise and abide by the legal requirements associated with these rights. • Users may download and print one copy of any publication from the public portal for the purpose of private study or research. • You may not further distribute the material or use it for any profit-making activity or commercial gain • You may freely distribute the URL identifying the publication in the public portal.
    [Show full text]
  • Tabulated Data
    TABLE OF CONTENTS VOLUME I A. VERTICAL LOAD VS. CHANGE IN ROLLING HEIGHT ...1 11 -00 - 22/G (90 PSI) 12.00 - 20/G (80 PSI) 15.00 - 22.5/H (90 PSI) CAMBER STIFFNESS VS. TIRE LOAD ......... 3 CORNERING STIFFNESS VS. TIRE LOAD. ..3 CIRCUMFERENTIAL STIFFNESS VS. TIRE LOAD. ...... 3 LATERAL SPRING RATE VS. TIRE LOAD. ......... 3 11.00 - 2216 (90 PSI) 12.00 - 20/G (80 PSI) 15.00 - 22.5/H (90 PSI) LATERAL SPRING RATE VS. INFLATION PRESSURE ..... 3 TABULATED DATA ................ 5 Circumferential Stiffness Cornering Stiffness Camber Stiffness Lateral Spring Rate Vertical Spring Rate For 9.00 - 20 E 9.00 - 20 F 10.00 - 20 F 10.00 - 20 G 17.00 - 22 F 11.00 - 22 G B. FX/FZ VS. FZ/FZ-RATED ON ASPHALT .....7 FXIFZ VS. VERTICAL LOAD ON ASPHALT ......... 8 FX/FZ VS. VELOCITY ON ASPHALT. ...:....... 9 FX/FZ VS. TEST RUNS ON ASPHALT ...........10 Firestone Transport I 10-20/F 8 100 PSI Goodyear Superhimiler 10-20/F @ 100 PSI General Power Jet 10-2O/F @ 100 PSI Goodyear Superhimi 1 er 11-22.5/F @ 100 PSI Firestone Transport I 12-20/H @ 120 PSI Uniroyal Unimaster Rib 15-22.5/l-1 I Research Injiiibt..Fl"" ILP 1 FX/FZ VS. NORMALIZED LOAD ON ASPHALT & CONCRET FXIFZ VS. VELOCITY ON ASPHALT & CONCRETE . , . 12 Firestone Transport I 10.00 x 20/F Goodyear Super Hi Miler 10.00 x 20/F FX/FZ VS. ASTM SKID NUMBER . 13 Firestone Transport I 10.00 x 20/F Goodyear Super Hi MIler 10.00 x 20/F C.
    [Show full text]