DOCSLIB.ORG

Spin Valve Systems for Angle Sensor Applications

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Spin Valve Systems for Angle Sensor Applications Spin Valve Systems for Angle Sensor Applications vom Fachbereich Material- und Geowissenschaften der Technischen Universität Darmstadt genehmigte Dissertation zur Erlangung des akademischen Grades eines Doktors der Ingenieurswissenschaften (Dr.-Ing.) eingereicht von M. Sc. Andrew Johnson aus Cincinnati, Ohio USA Referent: Prof. Dr.-Ing. Horst Hahn Korreferent: Prof. Dr.-Ing. Hartmut Fuess Tag der Einreichung: 25. Juli 2003 Tag der mündlichen Prüfung: 20. Januar 2004 Darmstadt 2004 D17 I Table of Contents 1 Introduction 1 2 Theory 5 2.1 Electrical Resistance and Magnetoresistance ......................................................5 2.2 Anisotropic Magneto Resistance (AMR).............................................................5 2.3 Giant Magneto Resistance (GMR).......................................................................7 2.4 Spin-Dependent Scattering ................................................................................10 2.4.1 Co/Cu Bandgap Structure........................................................................10 2.4.2 Mott Two-Current Model ........................................................................12 2.5 Spin Valve System.............................................................................................13 2.5.1 Magnetoresistance Characteristics of a Spin Valve.................................14 2.5.2 Uniaxial Anisotropy in the Free Layer and Pinned Layer.......................16 2.5.3 Interlayer Coupling in a Spin Valve System ...........................................18 2.5.4 Unidirectional Anisotropy: Exchange Bias .............................................19 2.5.5 Spin Valve Systems: Standard Materials and Microstructure. ................21 2.6 Exchange Bias Models.......................................................................................23 2.6.1 Ideal Interface Model...............................................................................24 2.6.2 Partial Domain Wall Model.....................................................................25 2.6.3 Random-Field Model...............................................................................26 2.6.4 Domain State Model................................................................................27 2.7 Synthetic Anti-Ferromagnet (SAF)....................................................................28 2.8 GMR 360° Angle Sensor ...................................................................................31 2.8.1 Design of GMR 360° Angle Sensor ........................................................31 2.8.2 Previous Research on GMR Angle Sensors ............................................33 2.8.3 Advantages of a GMR 360° Angle Sensor..............................................34 3 Experimental Methods 35 3.1 Sputter Deposition..............................................................................................35 3.1.1 The Sputtering Process ............................................................................35 3.1.2 Magnetron Sputtering ..............................................................................36 3.1.3 Unaxis Cyberite Sputtering System.........................................................37 3.1.4 Spin Valve Deposition Conditions ..........................................................39 3.2 Excimer-Laser....................................................................................................40 3.2.1 Theory and Basic Design of a Laser........................................................40 3.2.2 Excimer Lasers ........................................................................................41 4 Characterization Methods 45 4.1 Magnetoresistance measurements......................................................................45 4.1.1 Four-Point Probe......................................................................................45 II 4.1.2 Measurement Setup .................................................................................46 4.1.3 Analysis of the MR Rotation Curve ........................................................47 4.2 Structural Characterization ................................................................................48 4.2.1 X-Ray Diffraction....................................................................................48 4.2.2 X-Ray Reflectometry...............................................................................50 4.2.3 Auger Electron Spectroscopy ..................................................................51 4.3 Magnetic Characterization .................................................................................52 4.3.1 Alternating Gradient Magnetometer........................................................52 4.3.2 Magnetic Optical Kerr Effect ..................................................................53 5 Stoner-Wohlfarth Model: Spin Valve Systems 55 5.1 Applied Field Influence on Ferromagnetic Thin Film.......................................55 5.2 Model Description: Simple Spin Valve .............................................................55 5.3 Model for Spin Valve with SAF ........................................................................57 6 Results and Discussion 59 6.1 Cosine Dependence: Deviation Factors .............................................................61 6.1.1 AMR Effect .............................................................................................61 6.1.2 Interlayer Coupling..................................................................................65 6.1.3 Rotation of the Pinned Layer Magnetization..........................................70 6.1.4 Overview of the Cosine Deviation Factors..............................................73 6.1.5 Simulation of MR Rotation Curves.........................................................74 6.1.6 Cosine Deviation Factors: Implications for a 360° Angle Sensor...........80 6.1.7 Summary: Cosine Deviation Factors.......................................................82 6.2 Selection of Spin Valve System.........................................................................83 6.2.1 NiO Spin Valve System...........................................................................83 6.2.2 FeMn Spin Valve System .......................................................................86 6.2.3 IrMn Spin Valve System .........................................................................89 6.2.4 PtMn Spin Valve System.........................................................................91 6.2.5 PtMn Spin Valve System with SAF ........................................................94 6.2.6 Comparison Between the Different Spin Valve Systems......................101 6.2.7 Summary: Selection of Spin Valve System...........................................103 6.3 Multiple Deposition: Lift-off Method..............................................................104 6.3.1 Description of the Method.....................................................................104 6.3.2 Test of the Lift-off Method....................................................................104 6.3.3 Summary: Lift-off Method ...................................................................105 6.4 Ion Irradiation Method.....................................................................................106 6.4.1 Ion Irradiation of FeMn and IrMn Spin Valves.....................................106 6.4.2 Ion Irradiation of a Patterned Spin Valve Sample.................................108 6.4.3 Summary: Ion Irradiation Method........................................................110 6.5 Laser-writing Method ......................................................................................111 6.5.1 Laser Writing of FeMn and IrMn Simple Spin Valves .........................111 6.5.2 Reorientation Point: Gradual Change in Bias Direction .......................117 6.5.3 Complete Loss of GMR Effect and Exchange Bias .............................119 6.5.4 Source of the GMR Effect Reduction....................................................123 6.5.5 Domain State Model: Stability of the Exchange Bias Effect ................129 6.5.6 Laser Writing Experiments: PtMn Spin Valve with SAF .....................131 6.5.7 Antiferromagnetic Interlayer Coupling and the Reorientation Process.135 6.5.8 Induced Uniaxial Anisotropy of PtMn and the Reorientation Process..137 6.5.9 Induced Uniaxial Anisotropy: FeMn and IrMn Antiferromagnets........139 6.5.10Summary: Laser-Writing Method.........................................................141 7 Demonstrator of a 360° GMR Angle Sensor 143 III 7.1 Design and Fabrication ....................................................................................144 7.2 Demonstrator in Operation...............................................................................145 8 Summary of Conclusions 147 8.1 Summary ..........................................................................................................147 8.2 Future Work .....................................................................................................149 9 Zusammenfassung und Ausblick 151 9.1 Zusammenfassung............................................................................................151 9.2 Zukünftige Fragestellungen und Ausblick.......................................................153 10 Appendices 155 11 Citations 159 1 1Introduction Research on the Giant Magneto-Resistance (GMR) effect, large resistance changes due to an applied magnetic field, began
Load more

Recommended publications
  • A Brief Review of Ferroelectric Control of Magnetoresistance in Organic Spin Valves Xiaoshan Xu University of Nebraska-Lincoln, [email protected]
    University of Nebraska - Lincoln DigitalCommons@University of Nebraska - Lincoln Xiaoshan Xu Papers Research Papers in Physics and Astronomy 2018 A brief review of ferroelectric control of magnetoresistance in organic spin valves Xiaoshan Xu University of Nebraska-Lincoln, [email protected] Follow this and additional works at: https://digitalcommons.unl.edu/physicsxu Part of the Atomic, Molecular and Optical Physics Commons, Condensed Matter Physics Commons, and the Engineering Physics Commons Xu, Xiaoshan, "A brief review of ferroelectric control of magnetoresistance in organic spin valves" (2018). Xiaoshan Xu Papers. 11. https://digitalcommons.unl.edu/physicsxu/11 This Article is brought to you for free and open access by the Research Papers in Physics and Astronomy at DigitalCommons@University of Nebraska - Lincoln. It has been accepted for inclusion in Xiaoshan Xu Papers by an authorized administrator of DigitalCommons@University of Nebraska - Lincoln. J Materiomics 4 (2018) 1e12 Contents lists available at ScienceDirect J Materiomics journal homepage: www.journals.elsevier.com/journal-of-materiomics/ A brief review of ferroelectric control of magnetoresistance in organic spin valves Xiaoshan Xu Department of Physics and Astronomy, Nebraska Center for Materials and Nanoscience, University of Nebraska, Lincoln, NE 68588, USA article info abstract Article history: Magnetoelectric coupling has been a trending research topic in both organic and inorganic materials and Received 16 September 2017 hybrids. The concept of controlling magnetism using an electric field is particularly appealing in energy Received in revised form efficient applications. In this spirit, ferroelectricity has been introduced to organic spin valves to 8 November 2017 manipulate the magneto transport, where the spin transport through the ferromagnet/organic spacer Accepted 11 November 2017 interfaces (spinterface) are under intensive study.
    [Show full text]
  • Spin Polarized Current Phenomena in Magnetic Tunnel Junctions
    SPIN POLARIZED CURRENT PHENOMENA IN MAGNETIC TUNNEL JUNCTIONS A DISSERTATION SUBMITTED TO THE DEPARTMENT OF APPLIED PHYSICS AND THE COMMITTEE ON GRADUATE STUDIES OF STANFORD UNIVERSITY IN PARTIAL FULFILLMENT OF THE REQUIREMENTS FOR THE DEGREE OF DOCTOR OF PHILOSOPHY Li Gao September 2009 © Copyright by Li Gao 2009 All Rights Reserved ii I certify that I have read this dissertation and that, in my opinion, it is fully adequate in scope and quality as a dissertation for the degree of Doctor of Philosophy. _________________________________________________ (James S. Harris) Principal Advisor I certify that I have read this dissertation and that, in my opinion, it is fully adequate in scope and quality as a dissertation for the degree of Doctor of Philosophy. _________________________________________________ (Stuart S. P. Parkin) co-Principal Advisor I certify that I have read this dissertation and that, in my opinion, it is fully adequate in scope and quality as a dissertation for the degree of Doctor of Philosophy. _________________________________________________ (Walter A. Harrison) Approved for the University Committee On Graduate Studies. _________________________________________________ iii iv Abstract Spin polarized current is of significant importance both scientifically and technologically. Recent advances in film growth and device fabrication in spintronics make possible an entirely new class of spin-based devices. An indispensable element in all these devices is the magnetic tunnel junction (MTJ) which has two ferromagnetic electrodes separated by an insulator barrier of atomic scale. When electrons flow through a MTJ, they become spin-polarized by the first magnetic electrode. Thereafter, the interplay between the spin polarized current and the second magnetic layer manifests itself via two phenomena: i.) Tunneling magnetoresistance (TMR) effect.
    [Show full text]
  • Spin-Valve Effect in Nife/Mos2/Nife Junctions
    Spin-valve Effect in NiFe/MoS2/NiFe Junctions Weiyi Wang1,2, Awadhesh Narayan3,4, Lei Tang1, Kapildeb Dolui5, Yanwen Liu1,2, Xiang Yuan1,2, Yibo Jin1, Yizheng Wu1,2, Ivan Rungger3, Stefano Sanvito3, Faxian Xiu1,2, 1State Key Laboratory of Surface Physics and Department of Physics, Fudan University, Shanghai 200433, China 2Collaborative Innovation Center of Advanced Microstructures, Fudan University, Shanghai 200433, China 3School of Physics, AMBER and CRANN Institute, Trinity College, Dublin 2, Ireland 4Department of Physics, University of Illinois at Urbana-Champaign, Urbana, IL 61801, USA. 5Graphene Research Center and Department of Physics, National University of Singapore, 2 Science Drive 3, 117542, Singapore Correspondence and requests for materials should be addressed to F.X. (E-mail: [email protected]) 1 Abstract Two-dimensional (2D) layered transition metal dichalcogenides (TMDs) have been recently proposed as appealing candidate materials for spintronic applications owing to their distinctive atomic crystal structure and exotic physical properties arising from the large bonding anisotropy. Here we introduce the first MoS2-based spin-valves that employ monolayer MoS2 as the nonmagnetic spacer. In contrast with what expected from the semiconducting band-structure of MoS2, the vertically sandwiched-MoS2 layers exhibit metallic behavior. This originates from their strong hybridization with the Ni and Fe atoms of the Permalloy (Py) electrode. The spin-valve effect is observed up to 240 K, with the highest magnetoresistance (MR) up to 0.73% at low temperatures. The experimental work is accompanied by the first principle electron transport calculations, which reveal an MR of ~ 9% for an ideal Py/MoS2/Py junction.
    [Show full text]
  • Pseudo Spin Valve Behavior in Colloidally Prepared Nanoparticle Films Benjamin H
    Letter Cite This: ACS Appl. Electron. Mater. 2019, 1, 1065−1069 pubs.acs.org/acsaelm Pseudo Spin Valve Behavior in Colloidally Prepared Nanoparticle Films Benjamin H. Zhou† and Jeffrey D. Rinehart*,†,‡ † ‡ Materials Science and Engineering Program and Department of Chemistry and Biochemistry, University of California, San Diego, La Jolla, California 92093, United States *S Supporting Information ABSTRACT: Magnetoresistance provides a high-precision, versatile sensing mechanism that has continuously advanced in tandem with methods for top-down engineering of high-precision multilayer devices. Materials composed of solution-prepared nanocrystals can replicate some of the behavior of traditional magnetoresistive stacks but are limited by their intrinsic response mechanism: a gradual shift from low to high resistance with field. To fundamentally alter this behavior, we demonstrate the first instance of any form of spin valve behavior arising from a nanoparticle composite magnetoresistor. Single-layer films of varying CoFe2O4 to Fe3O4 nanoparticle ratios are used to show how the low-field sensitivity can be tuned to values exceeding those of either single-component material. Additionally, the sensitivity is shown to be a simple function of the magnetization of the individual component materials. KEYWORDS: colloidal nanomaterials, composite materials, spintronics, magnetoresistance, magnetism oon after the revolutionary discovery of giant magneto- Conversely, in a granular or nanocomposite magnetoresistor, S resistance (GMR) in multilayered structures,1,2 an application of an external magnetic field results in individual analogous effect was observed for magnetic grains in particle moments deviating from their original alignment with 3−7 Δ − conducting or insulating matrices. In this formulation, the the local anisotropy axes (maximum R/Rmax; Figure 1a ii,iv) matrix material acts as the spin-selecting junction between toward parallel alignment with the external field axis magnetically oriented grains, and the lack of structural (minimum ΔR/R; Figure1a−i,iii).
    [Show full text]
  • Spin Transport and Spin Torque in Antiferromagnetic Devices
    REVIEW ARTICLE https://doi.org/10.1038/s41567-018-0062-7 Corrected: Publisher Correction Spin transport and spin torque in antiferromagnetic devices J. Železný1,2*, P. Wadley3, K. Olejník2, A. Hoffmann4 and H. Ohno5,6,7,8 Ferromagnets are key materials for sensing and memory applications. In contrast, antiferromagnets, which represent the more common form of magnetically ordered materials, have found less practical application beyond their use for establishing refer- ence magnetic orientations via exchange bias. This might change in the future due to the recent progress in materials research and discoveries of antiferromagnetic spintronic phenomena suitable for device applications. Experimental demonstration of the electrical switching and detection of the Néel order open a route towards memory devices based on antiferromagnets. Apart from the radiation and magnetic-field hardness, memory cells fabricated from antiferromagnets can be inherently mul- tilevel, which could be used for neuromorphic computing. Switching speeds attainable in antiferromagnets far exceed those of ferromagnetic and semiconductor memory technologies. Here, we review the recent progress in electronic spin-transport and spin-torque phenomena in antiferromagnets that are dominantly of the relativistic quantum-mechanical origin. We discuss their utility in pure antiferromagnetic or hybrid ferromagnetic/antiferromagnetic memory devices. agnetism and technology have been inextricably linked Here, we review recent theoretical and experimental progress on for centuries—from the navigation compass, to motors spin-transport and spin-torque phenomena allowing for reading Mand generators, to magnetic data storage. The field of and writing information stored in antiferromagnets. See Fig. 1 for information storage has been dominated by ferromagnetic materi- a summary of all proposed electrical reading and writing methods.
    [Show full text]
  • Hot-Electron Transport in the Spin-Valve Transistor
    Hot-electron transport in the spin-valve transistor Ruud Vlutters 2001 Ph.D. thesis University of Twente Twente University Press Also available in print: www.tup.utwente.nl/uk/catalogue/technical/spin-valve Contents 1 Introduction 3 1.1 Spin-electronic materials 5 1.2 Spin-electronic devices 7 1.2.1 Spin Valves 7 1.2.2 Magnetic tunnel junctions 8 1.2.3 Spin-Valve Transistor 9 1.3 Spin-electronic applications 10 1.3.1 Magnetic read heads 10 1.3.2 MRAM 11 1.4 Thesis outline 12 1.5 Conclusions 12 2 Theory of the spin-valve transistor 13 2.1 Electron transport in the emitter and collector 15 2.1.1 Conduction electrons in silicon 15 2.1.2 Schottky diodes 17 2.1.3 Schottky emitter 19 2.1.4 Schottky collector 22 2.2 Electron transport in the metallic base 26 2.2.1 Scattering of Fermi-electrons in a spin valve 26 2.2.2 Hot-electron scattering 28 2.2.3 Hot-electron transport in a spin valve 34 2.2.3.1 The Boltzmann equation in a single layer 34 2.2.3.2 The Boltzmann equation in a magnetic multilayer 38 2.2.3.3 Numerical results 39 2.3 Theory overview: a simple model 43 2.4 Conclusions 46 3 Experimental procedures 49 3.1 Deposition setup 51 3.2 Spin-valve transistor processing 52 3.3 Electrical transport measurement setup 57 3.4 Conclusions 59 4 Experimental results 61 4.1 Current transport in Schottky diodes 63 4.2 Hot-electron emission and collection in metal base transistors 65 4.3 Hot-electron transport in the spin-valve transistor 69 4.3.1 Spin-wave scattering in magnetic materials 72 4.3.2 Hot-electron scattering in Ni80Fe20 73 4.3.2.1 Spin-dependence
    [Show full text]
  • Two-Dimensional Arrays of Vertically Packed Spin-Valves With
    www.nature.com/scientificreports OPEN Two‑dimensional arrays of vertically packed spin‑valves with picoTesla sensitivity at room temperature Marilia Silva1,2*, Fernando Franco1,2,4, Diana C. Leitao1,2, Susana Cardoso1,2 & Paulo P. Freitas1,3 A new device architecture using giant magnetoresistive sensors demonstrates the capability to detect very low magnetic felds on the pT range. A combination of vertically packed spin‑valve sensors with two‑dimensional in‑plane arrays, connected in series and in parallel, delivers a fnal detection level of 360 pT/√Hz at 10 Hz at room temperature. The device design is supported by an analytical model developed for a vertically packed spin‑valve system, which takes into account all magnetic couplings present. Optimization concerning the spacer thickness and sensor physical dimensions depending on the number of pilled up spin‑valves is necessary. To push the limits of detection, arrays of a large number of sensing elements (up to 440,000) are patterned with a geometry that improves sensitivity and in a confguration that reduces the resistance, leading to a lower noise level. The fnal device performance with pT detectivity is demonstrated in an un‑shielded environment suitable for detection of bio‑signals. Emerging biomedical applications using portable sensor devices ofer patients individualized and improved health monitoring1,2. High precision instruments for magnetic imaging 3–5 are contactless and can ofer superior outputs than electrical measurements, since magnetic signals are not attenuated by human tissue 6,7. Current technologies for ultra-low magnetic feld detection include Superconducting QUantum Interference Devices (SQUID)8 and Optical Pumping Magnetometry (OPM)9,10 reaching femto-tesla detection levels and more recently Spin Exchange Relaxation Free (SERF) atomic magnetometers on pico-tesla range11,12.
    [Show full text]
  • Antiferromagnetic Spintronics V
    Antiferromagnetic spintronics V. Baltz, A. Manchon, M. Tsoi, T. Moriyama, T. Ono, Y. Tserkovnyak To cite this version: V. Baltz, A. Manchon, M. Tsoi, T. Moriyama, T. Ono, et al.. Antiferromagnetic spintronics. Re- views of Modern Physics, American Physical Society, 2018, 90 (1), pp.015005. 10.1103/RevMod- Phys.90.015005. hal-01568760 HAL Id: hal-01568760 https://hal.archives-ouvertes.fr/hal-01568760 Submitted on 28 Apr 2019 HAL is a multi-disciplinary open access L’archive ouverte pluridisciplinaire HAL, est archive for the deposit and dissemination of sci- destinée au dépôt et à la diffusion de documents entific research documents, whether they are pub- scientifiques de niveau recherche, publiés ou non, lished or not. The documents may come from émanant des établissements d’enseignement et de teaching and research institutions in France or recherche français ou étrangers, des laboratoires abroad, or from public or private research centers. publics ou privés. REVIEWS OF MODERN PHYSICS, VOLUME 90, JANUARY–MARCH 2018 Antiferromagnetic spintronics V. Baltz* SPINTEC, Univ. Grenoble Alpes/CNRS/INAC-CEA, F-38000 Grenoble, France A. Manchon† King Abdullah University of Science and Technology (KAUST), Physical Science and Engineering Division (PSE), Thuwal 23955-6900, Saudi Arabia M. Tsoi Department of Physics, The University of Texas at Austin, Austin, Texas 78712-0264, USA T. Moriyama Institute for Chemical Research, Kyoto University, 611-0011 Uji, Kyoto, Japan T. Ono Institute for Chemical Research, Kyoto University, 611-0011 Uji, Kyoto, Japan Y. Tserkovnyak Department of Physics and Astronomy, University of California, Los Angeles, California 90095, USA (published 15 February 2018) Antiferromagnetic materials could represent the future of spintronic applications thanks to the numerous interesting features they combine: they are robust against perturbation due to magnetic fields, produce no stray fields, display ultrafast dynamics, and are capable of generating large magnetotransport effects.
    [Show full text]
  • Magnetoresistive Random Access Memory Michael C
    Magnetoresistive Random Access Memory Michael C. Gaidis IBM T.J. Watson Research Center Abstract Magnetoresistive Random Access Memory (MRAM) offers the potential of a universal memory – it can be simultaneously fast, nonvolatile, dense, and high-endurance. MRAM differs from earlier incarnations of magnetic memory in that MRAM tightly couples electronic readout with magnetic storage in a compact device structure competitive with state-of-the-art semiconductor memories. Small-scale demonstrations have realized much of the potential of MRAM, but shrinking the cell size or embedding the memory with logic circuitry creates difficult challenges. This chapter provides an overview of the basic MRAM magnetic structure, including an explanation of the functions of various elements in the complex multilayer magnetic film stack. Principles of MRAM circuit design and operation are covered, with a detailed look at the design of a single-bit cell. Also included is a discussion of the techniques developed to fabricate large arrays of MRAM devices with high yield. MRAM reliability issues and the potential for scaling MRAM for future device generations concludes the chapter. Contents 1. Magnetoresistive Random Access Memory (MRAM) 2. Basic MRAM 3. MTJ MRAM 3.1 Antiferromagnet 3.2 Reference Layer 3.3 Tunnel Barrier 3.4 Free Layer 3.5 Substrate 3.6 Seed Layer 3.7 Cap Layer 3.8 Hard Mask 4. MRAM Cell Structure and Circuit Design 4.1 Writing the Bits Toggle MRAM 4.2 Reading the Bits 4.3 MRAM Processing Technology and Integration Process Steps 5. MRAM Reliability 5.1 Electromigration 5.2 Tunnel Barrier Dielectrics 5.3 BEOL Thermal Budget 5.4 Film Adhesion 6.
    [Show full text]
  • Active Control of Magnetoresistance of Organic Spin Valves Using Ferroelectricity
    ARTICLE Received 11 Feb 2013 | Accepted 13 Jun 2014 | Published 10 Jul 2014 DOI: 10.1038/ncomms5396 OPEN Active control of magnetoresistance of organic spin valves using ferroelectricity Dali Sun1,2,3,*,w, Mei Fang1,*, Xiaoshan Xu2, Lu Jiang2,3, Hangwen Guo2,3, Yanmei Wang1, Wenting Yang1, Lifeng Yin1, Paul C. Snijders2,3, T.Z. Ward2, Zheng Gai2,4, X.-G. Zhang4,5, Ho Nyung Lee2 & Jian Shen1,3 Organic spintronic devices have been appealing because of the long spin lifetime of the charge carriers in the organic materials and their low cost, flexibility and chemical diversity. In previous studies, the control of resistance of organic spin valves is generally achieved by the alignment of the magnetization directions of the two ferromagnetic electrodes, generating magnetoresistance. Here we employ a new knob to tune the resistance of organic spin valves by adding a thin ferroelectric interfacial layer between the ferromagnetic electrode and the organic spacer: the magnetoresistance of the spin valve depends strongly on the history of the bias voltage, which is correlated with the polarization of the ferroelectric layer; the magnetoresistance even changes sign when the electric polarization of the ferroelectric layer is reversed. These findings enable active control of resistance using both electric and magnetic fields, opening up possibility for multi-state organic spin valves. 1 State Key Laboratory of Surface Physics and Department of Physics and Collaborative Innovation Center of Advanced Microstructure, Fudan University, Shanghai 200433, China. 2 Materials Science and Technology Division, Oak Ridge National Laboratory, Oak Ridge, Tennessee 37831, USA. 3 Department of Physics and Astronomy, University of Tennessee, Knoxville, Tennessee 37996, USA.
    [Show full text]
  • Magnetoresistive Random Access Memory Dmytro Apalkov, Bernard Dieny, J
    Magnetoresistive Random Access Memory Dmytro Apalkov, Bernard Dieny, J. Slaughter To cite this version: Dmytro Apalkov, Bernard Dieny, J. Slaughter. Magnetoresistive Random Access Memory. Pro- ceedings of the IEEE, Institute of Electrical and Electronics Engineers, 2016, 104, pp.1796 - 1830. 10.1109/JPROC.2016.2590142. hal-01834195 HAL Id: hal-01834195 https://hal.archives-ouvertes.fr/hal-01834195 Submitted on 10 Jul 2018 HAL is a multi-disciplinary open access L’archive ouverte pluridisciplinaire HAL, est archive for the deposit and dissemination of sci- destinée au dépôt et à la diffusion de documents entific research documents, whether they are pub- scientifiques de niveau recherche, publiés ou non, lished or not. The documents may come from émanant des établissements d’enseignement et de teaching and research institutions in France or recherche français ou étrangers, des laboratoires abroad, or from public or private research centers. publics ou privés. Magnetoresistive Random Access Memory Dmytro Apalkov 1, Bernard Dieny 2, J. M. Slaughter 3 1. Samsung Electronics, Semiconductor R&D Center, San Jose, California, USA. 2. SPINTEC, Grenoble Alpes Univ, CEA, CNRS, CEA/Grenoble, INAC, Grenoble, FRANCE 3. Everspin Technologies, Inc., Chandler, Arizona, USA Abstract A review of the developments in MRAM technology over the past 20 years is presented. The various MRAM generations are described with a particular focus on Spin-Transfer-Torque MRAM (STT-MRAM) which is currently receiving the greatest attention. The working principles of these various MRAM generations, the status of their developments, and demonstrations of working circuits, including already commercialized MRAM products, are discussed. Keywords: MRAM, spintronics, spin electronics, magnetic tunnel junctions, tunnel magnetoresistance, spin transfer torque, STT-MRAM, toggle, thermally assisted MRAM 1 OUTLINE 1.
    [Show full text]
  • Chapter 14: Spin Electronics and Magnetic Recording
    Chapter 14: Spin Electronics and Magnetic Recording 1. Spin currents 2. Sensors 3. Memory 4. Logic 5. Spin transistors 6. Magnetic recording Comments and corrections please: [email protected] Dublin April 2007 1 Further reading • Michael Ziese and Martin Thornton (editors), Spin Electronics , Springer, Berlin 2001, 493 pp. A multiauthor volume which treats topics at an introductory level, with some emphasis on oxide spin electronics. • Uwe Hartmann (editor) Magnetic Multilayers and Giant Magnetoresistance , Springer, Berlin 1999, 321pp. Readable articles focussed on magnetic multilayers and giant magnetoresistance. • Mark Johnson (editor), Magnetoelectronics , Elsevier Amsterdam 2004, 396 pp. Covers magnetoelectronics in a series of articles, from an introduction to chapters on logic, tunelling and biochips. • Sadamichi Maekawa (editor), Concepts in Spin Electronics , Oxford 2006, 398 pp. A monograph with a focus on theoretical aspects. • Lawrence Comstock, Introduction to Magnetism and Magnetic Recording, Wiley-Interscience 1999, 485 pp. A n extensive and useful introduction for engineers. • M. L. Plumer, J. van Eck and D. Weller (editors) The Physics of Ultra-high Density Magnetic Recording , Springer, Berlin 1999, 355 pp. A series of articles covering micromagnetic and dynamic aspects of recording with a focus on media. Dublin April 2007 2 Modern Electronics Logic; CMOS - Complementary Metal-Oxide Semiconductor. Uses p and n type silicon, carriers are electrons or holes in FETs. It consumes power only when switching, and it is scalable. p-type NAND gate n-type Memory; SRAM - Static Random-Access Memory. 6T Volatile DRAM - Dynamic Random-Access Memory 1T Volatile, refreshed every few ms. FLASH - Nonvolatile; limited rewritability Dublin April 2007 3 Dublin April 2007 4 Conventional electronics has ignored the spin in the electron : The electron is a mobile particle with a charge e = -1.6 10-19 C ! It also has quantized angular momentum ms where m s = ±1/2 spin up ! or spin down " ! The associated magnetic moment is m = e /2m = 1 Bohr magneton (µB).
    [Show full text]