Digital/Analog Migration IDAS™ Conventional IP Network IDAS™ Trunking IDAS is Icom’s digital land mobile system using the NXDN™ common air interface and offers a com- plete system of handheld , mobile radios, , network interface/trunking controller, IP-based virtual radio, various accessories and a complete system solution.

IDAS™ system features P1

D IDAS™ calling features P2

IDAS™ conventional IP network P3

Ch IDAS™ trunking features P5

IDAS™ products lineup P6

IDAS™ system features

Digital/analog mixed mode operation communication with no reduction in Digital signal advantage IDAS radios can receive both analog channel capacity, even if a When comparing digital with analog mode and digital mode signals on a site is not available, or goes down. FM, the audio quality of analog FM single channel. You can partially intro- gradually deteriorates with static noise duce the IDAS radios while using your as the distance increases. On the Spectrum efficiency existing analog radios in a system. The other hand, the digital audio provides IDAS system allows you to scale migra- The IDAS system doubles the capac- noise-less, stable audio for longer tion to narrow band digital at your own ity of the current 12.5kHz channel al- until the fringes of the communication pace and needs, while running your ex- location. Icom provides a solution to range. isting analog system. It is a cost effi- overcrowded airwaves. cient way to obtain the next generation Spectrum efficiency Analog vs Digital Coverage in two way radio technology, while pro- Audio quality tecting your current system investment. Existing Analog FM IDASTM Digital (12.5kHz) (6.25kHz x 2) Excellent

Better audio quality Peer-to-peer communication with FDMA IDAS Better distance When compared to a TDMA (Time Di- coverage vision Multiple Access) 6.25 equivalent Analog FM system, the FDMA (Frequency Division Minimum required audio quality Multiple Access) enables "peer to peer" communication between radios Signal Poor strength in 6.25kHz digital mode. It ensures High level Low level

1 D D IDAS™ calling features IDAS™ IDAS supports following calling features in digital conventional mode. Common calling features IDAS™ conventional IP network

Selective call, group call sent to the dispatcher or another radio. or stolen radio over the air, eliminat- and talkgroup ID Other emergency features are a man ing security threats from undesired lis- down feature*1 and a lone worker func- teners. When the radio stun command is The IDAS system allows you to call tion, available for automated emer- received, all functions will be temporary individual or group users. IDAS radios Ch gency calls (in digital and analog locked out until the revive command is

automatically send their own ID number IDAS™ modes). A remote radio monitor func- received or the user password is en- when the PTT button is held down. tion allows the dispatcher to turn on tered. The IDAS radio can also send IDAS radios memorize up to 500 of both the PTT button from a remote location radio stun, kill and revive commands. trunking features individual/group ID numbers and alias and transmit anything the microphone names in the table. The alias name or hears for a preprogrammed time period. individual/group ID is displayed on the RAN for digital code squelch *1 Optional UT-124R required. LCD while receiving a message allow- The RAN (Radio Access Number) code ing you to identify who is calling. Status message is the digital equivalent of CTCSS for accessing an IDAS repeater or digital You can set up to 100 conditions such Talk back function and squelch function. as "on duty", "at lunch" or “in route”. call mode selection This message will be sent each time When the talk back function is enabled, the PTT button is pushed until the Short Data Message capability the IDAS radio automatically selects the status message feature is turned off. Short data messages of up to 12 received talkgroup or individual ID to Also, you can request another unit to characters may be sent and received IDAS™ products lineup reply to the received call, while the talk send their status and receive it. between IDAS radios or from the back timer remains. After the talk back remote communicator. timer is exceeded, the IDAS radios will GPS position reporting set to an initial call mode depending on Other features programming which is either talkgroup When used with the HM-170GP GPS or individual call or retain the previous speaker microphone for the handheld • Radio check function allows you to user call mode selection. IDAS radio or an external, third-party verify if another radio is within commu- GPS for the mobile IDAS radio, you nication range can send your current position infor- • Call log displays the received call his- Digital voice scrambler mation to another radio or the dis- tory When secure communication is re- patch. Three different sending inter- • Call alert function notifies receiving quired, the IDAS system provides a vals can be programmable: on PTT; party that a call is coming with a beep digital voice scrambler using a 15-bit key when polled; or at periodic times. sound and blinking icon When connected to a PC that has (about 32,000 codes) as standard. This • operation for repeater is added security to the digital mapping software installed, the dis- • Late entry: IDAS radio can decode the modulation/demodulation. patch will know the real-time activity of the fleet members. received ID and show group ID, unit ID or alias name on the display even Emergency call functions when turned on during a conversation. When the emergency button is pushed, an Radio kill, stun and revive emergency signal will be automatically The radio kill function disables a lost

2 D IDAS™ conventional IP network IDAS™ IDAS™ conventional IP network links up to 16 repeater sites calling features

Communication link for distant locations

6.25kHz IDAS digital IP Network

Digital Radio

SITE A Digital Radio IDAS™ Repeater SITE C conventional IP network

IP Network Repeater Monitors group B conversation

Repeater

#02 SITE B IDAS™ Network Controller Provides the ability to interface an IP network to the IDAS repeater. Digital Radio

Ch Remote Communicator IDAS™

Communication link for distant locations mode is enabled though some restric- RC-FS10 Remote Communicator trunking features tions may still be applicable. An IDAS conventional IP network can The remote communicator creates an extend your communication coverage. IP-based virtual radio on a PC and Integrated system for It lets you connect dispersed sites and works as a simple dispatch. IDAS allows you to communicate like a single clean and simple installation communication features can be used site. Icom has made it simple and easy to with the remote communicator software. introduce and install an IDAS conven- Up to 8 target IDAS repeater sites* can Up to 16 IDAS™ repeaters tional IP network system. The IDAS be programmable in the software. 8 connection over IP network conventional IP network system remote communicators can connect to With the optional UC-FR5000 (#02), up requires only the UC-FR5000 (#02) a single repeater. to 16 IDAS repeaters can be interlinked network controller which can be * The RC-FS10 software can transmit one voice with each other. An IDAS terminal radio installed into the IC-FR5100 series path at a time. One CT-24 is required for receiv- user can communicate with other IDAS repeater – no control server and no ing an IDAS repeater site and up to 8 repeater IDAS™ products lineup terminal radio users belonging to the extra rack space is required. In sites can be monitored simultaneously with 8 CT-24s. interlinked repeater sites and/or a addition, the repeater and network virtual dispatch station on the network. controller settings can be remotely * The IDAS conventional IP network cannot maintained and monitored over an IP relay voice traffic over the IP network if the connected PC. uplink is analog.

Low bandwidth requirement RC-FS10 screen By using the AMBE+2™ vocoder Site tab : Flexible settings compression, an IDAS conventional IP Up to 8 repeaters are The button layout, button programmable name, button color and network requires only about 13kbps background color can be bandwidth per one voice path in theory. Function buttons : customized freely. It means a DSL class line is sufficient Up to 40 functions are programmable. for the IDAS conventional IP network. DTMF The IDAS conventional IP network Communication Short Data Message system requires only one fixed IP log and ANI and Status Message The software shows user Sending and receiving a address in a group of networked ID and name who is short data message and repeaters. Other repeater sites can using the target repeater status message can be work with dynamically allocated IP on the display and creates made easily. communication logs. addresses when the IP manager/client

3 D IDAS™ IDAS™ conventional IP network application example calling features

CASE 1 Intra-building and inter-building solution CASE 2 Crossband repeater

IDAS digital IP Network (LAN) IDAS digital IDAS digital IP Network (VHF) (UHF)

Repeater High layerla

VHF Radios UHF Radios IDAS™

Repeater VHF Repeater UHF Repeater Mid layeray

LAN IP Network conventional IP network

Mid layer Dispatch Building B MonitorsMonitors groupgroup B conversationconversation

Group A Dispatch Group B Dispatch

Repeater Basement User Group A User Group B Building A VHF Network UHF Network

With an IDAS conventional IP network system, it is possible to Different agencies might use different bands. For example, a have radio communications all the way from the basement to police department might be using UHF while a fire department

the top floor, all in stable digital audio. Already deployed LAN uses VHF. An IDAS conventional IP network establishes a cross- Ch cables can be used in an in-building solution. band repeater system so everyone can communicate with each other. IDAS™ trunking features

CASE 3 Remote base station over IP network CASE 4 Receiver voting operation

IDAS digital IDAS digital IP Network IDAS digital IDAS digital IDAS digital IP Network (Uplink) (Downlink) (Uplink A) (Uplink B) (Downlink)

Downlink Repeater (Tx & Rx)

SITE B

Dispatch Repeater IP Network Downlink IDAS™ products lineup

Repeater Base mode Uplink SITE C (Repeater disabled) Repeater (Rx only) SITE A IP Network

Uplink Dispatch

Repeater (Rx ononly)

In base mode operation with an IDAS conventional IP network IDAS receiver voting improves the talk back capability of IDAS system, the uplinked voice from IDAS radios will not be handheld and mobile radios. The IDAS networked receivers repeated to other IDAS terminal radios, but only sent to the (where IDAS repeaters’ transmission is inhibited and used as assigned virtual radio/dispatcher via IP. The uplink from the receivers) are distributed to the communication area. Each virtual radio /dispatcher will be down-linked from the IDAS receiver receives a signal from a terminal radio and transfers it to repeaters. This mode may be used in case communications the repeater site, and the repeater relays the best signal or between terminals is not intended or may be used in a simplex transfers it to the remote dispatch. The UC-FR5000 has a built-in channel system. voting function, so an external voter device is not required.

4 D Ch IDAS™ trunking features IDAS™ IDAS™ trunking for efficient channel management calling features

Shares up to 30 channels with a large number of users

6.25kHz digital trunking (Ch1) 6.25kHz digital trunking (Ch16) 6.25kHz digital trunking (Ch30) IP Network

Digital Radios IDAS™ Ch16 conventional IP network

Digital Radios Digital Radios Ch1 Ch30

IP Network Ch1 #01/#02 IDAS Trunking Controller 1 unit required per channel. Ch

IDAS™ Ch16

trunking features Setting Ch30 IDAS Trunking Repeaters

Distributed control channel Web browser configuration Two RF modules in one unit The IDAS trunking system is a distrib- All of the UC-FR5000 configurations The IC-FR5100 series uses only 2U uted system (similar to the analog can be made via a Web browser. height and has an internal space for LTR™ trunking) which does not have installing another RF module. The a dedicated control channel. Trunking

IDAS™ products lineup optional UR-FR5100 series RF channels can be used for voice chan- module can be installed in the nels to share more effectively with a chassis to save installation space. large number of users. *For a two channel IDAS trunking repeater, an optional UC-FR5000 (#01/#02) is Number of unit ID and talkgroup ID required for each channel. The IDAS trunking system can have up to 30 channels (RF units) per site. The system has the potential ability to Secondary home channel UC-FR5000, IDAS Trunking Controller handle up to 2000 unit ID codes and If the home repeater fails, the system 2000 talkgroup ID codes per home automatically switches to a secondary channel. The practical number of users repeater/channel for backup operation. in any one system (site) may vary due to many factors, but the IDAS trunking UR-FR5100 series, Channel Module system is designed to be used by up to Area bit setting 100 to 200 users (radios) per channel. If there are two IDAS trunking systems using the same frequency within a Please note: The IDAS multi-site trunking/IP close area, the area bit setting allows networking system is not available at this time. the trunked radios to identify its own 2 channel IDAS trunking repeater It will be release in the future. repeater site.

5 D

IDAS™ products lineup IDAS™ calling features VHF DIGITAL/ANALOG REPEATER UHF DIGITAL/ANALOG REPEATER

25W IDAS™ conventional IP network Features Options Frequency coverage : 136-174MHz, 400-470MHz Number of channels : Max. 32 channels 19-inch rack mount design, 2U height low profile design 12-digit dot-matrix display and 32 memory channels UC-FR5000 CF-FR5000MC Multiple CTCSS, DTCS tone and digital RAN code decode IDAS Trunking/Network Controller CF Card For IDAS Conventional IP network, IP Network Upgrade Software 25W output power at 100% duty operation UC-FR5000 #02 required. for UC-FR5000 #01. (or upgrade UC-FR5000 #01 * CF-FR5000MC is already “2 channel in 1 box” configuration (Optional UR-FR5100/UR-FR6100 required) with CF-FR5000MC) installed to UC-FR5000 #02. 5-Tone and DTMF encoder/decoder (For analog FM mode) Ch Accessory connector (D-sub 25-pin) for connecting analog trunking

controllers or other external devices IDAS™ Audio compander (For Analog FM mode)

UR-FR5100 (VHF) Two RF units can be installed in the unit. trunking features Built-in inversion type voice scrambler and optional UT-109R/UT-110R for UR-FR6100 (UHF) (Left side is an option.) higher security (For analog FM mode) Channel Modules CW ID

Remote Communicator IDAS™ products lineup

CT-24 RC-FS10 Remote Communicator CT-23 PTT Microphone Adapter BC-147SA/SE SM-25 Desktop Microphone HM-152 Hand Microphone CT-24 Digital Voice Converter (Supplied with RC-FS10) AC Adapter

USB cable Audio cable

BC-147SA/SE or AC Adapter (Option) CT-24 CT-23 Digital Voice Converter RC-FS10 PTT Microphone Adapter SM-25 Desktop HM-152 Hand (Supplied with RC-FS10) (Option) Microphone (Option) Microphone (Option)

• CT-23 connects HM-152 or SM-25 microphone audio (RJ-45 jack) converts microphone audio to an IDAS compatible digital signal. and PTT/Monitor signals to the 3.5mm stereo jack for connection The remote communicator software will not work if the CT-24 is with a PC. A stereo jack cable is supplied with the CT-23. AC not connected. adapter, BC-147SA/SE is required separately. • RC-FS10SDK: Allows you to develop IDAS compatible applica- • The digital voice converter, CT-24, is a USB device which tions. (A non-disclosure agreement required)

6 VHF DIGITAL/ANALOG UHF DIGITAL/ANALOG TRANSCEIVERS D IDAS™

calling features Features Options Frequency coverage: 136-174MHz, 400-470MHz Compatibility with digital 6.25kHz NXDN™ protocol. Abundant digital functions 5W 5W (VHF/UHF) (VHF/UHF) 512 memory channels with 128 zones Dot matrix, multi-function LCD HM-170GP HS-95 GPS Speaker-microphone Behind-the-head Headset Large capacity Lithium-Ion battery pack Dust-protection and waterjet resistance equivalent to IP55 MIL-STD rugged construction 5W RF output power Operating time: 14 hours* (approx. with BP-232N battery pack) * Tx: Rx: standby=5:5:90.Power save on. (at 20°C) IDAS™ VS-1SC UT-124R Loud speaker audio with BTL amplifier and audio compander PTT/ VOX Unit Man Down Unit conventional IP network Built-in 2-Tone / 5-Tone / CTCSS / DTCS / MDC 1200 signaling (For analog FM mode) BIIS 1200 compatible (For Analog FM mode) Built-in inversion type voice scrambler and optional UT-109R/UT-110R for T Series S Series higher security (For analog FM mode) (10-Keypad Version) (Simple Keypad Version)

VHF DIGITAL/ANALOG UHF DIGITAL/ANALOG TRANSCEIVER

Ch Features

IDAS™ Frequency coverage : 136–174MHz, 400–470MHz 25W Compatibility with digital 6.25kHz NXDN™ protocol. Abundant digital functions trunking features 512 memory channels with 128 zones Large dot matrix display and multi-function LCD Detachable front panel with optional RMK-3 and separation cable Options D-Sub accessory connector and ignition sensing line 25W RF output power IP54 dust-protection and splash resistance (Front panel only) MIL-STD rugged construction

Front mounted loud speaker and audio compander SM-25 HM-148G SP-30 Desktop Microphone Hand Microphone External Speaker Built-in 2-Tone / 5-Tone / CTCSS / DTCS / MDC 1200 signaling (For analog FM mode) Heavy duty, dynamic microphone BIIS 1200 compatible (For Analog FM mode)

IDAS™ products Lineup Built-in inversion type voice scrambler and optional UT-109R/UT-110R for higher

security (For analog FM mode) OPC-609 (1.9m; 6.2ft) OPC-607 (3m; 9.8ft) OPC-726 (5m; 16.4ft) OPC-608 (8m; 26.2ft)

RMK-3 Separation Cables Separation Kit

Icom, Icom Inc. and the Icom logo are registered trademarks of (Japan) in the United States, the United Kingdom, Germany, France, Spain, Russia, Japan and/or other countries. IDAS, IDASLes logo spéci are trademarksfi cations of Icom et informations Incorporated. NXDN données is a trademark dans of Icomce document Incorporated andpeuvent Kenwood être Corporation. modifi AMBE+2ées sans is a trademarkpréavis. and La property confi gurationof Digital Voice du Systems poste Inc.peut LTR varier is a trademark suivant of EFJohnson les versions. Technologies, Inc.

1-1-32, Kami-minami, Hirano-ku, Osaka 547-0003, Japan Phone: +81 (06) 6793 5302 Fax: +81 (06) 6793 0013 www.icom.co.jp/world Count on us! CACHET DISTRIBUTEUR Zac de la Plaine - 1, Rue Brindejonc des Moulinais BP 45804 - 31505 TOULOUSE CEDEX 5 Blacksole House, Altira Park, Tél : +33 (0)5 61 36 03 03 - Fax : +33 (0)5 61 36 03 00 Herne Bay, Kent, CT6 6GZ, U.K. WEB ICOM : http://www.icom-france.com Phone : +44 (01227) 741741 [email protected] Fax : +44 (01227) 741742 E-mail : E-mail : [email protected] URL : http://www.icomuk.co.uk

Communication Equipment Auf der Krautweide 24 65812 Bad Soden am Taunus, Germany Phone : +49 (6196) 76685-0 Fax : +49 (6196) 76685-50 E-mail : [email protected] URL : http://www.icomeurope.com

09HS0210 ©2009 Icom Inc.