DOCSLIB.ORG

Alloy Steelssteels High Strength Low Alloy (HSLA)

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Alloy Steelssteels High Strength Low Alloy (HSLA) 77 AlloyAlloy SteelsSteels High strength low alloy (HSLA). a type of steel alloy that provides many benefits over regular steel alloys contain a very small percentage of carbon (less than one-tenth of a percent) and only small amounts of very specific alloying elements referred to as 'microalloyed', as they are indeed alloyed in extremely small amounts by comparison to other main commercial alloy steels group of low carbon steels that utilize small amounts of alloying elements to attain yield strengths in excess of 275 MPa in the as-rolled or normalized conditions SME 1613 : Materials Science 2007 TYPICAL CHEMICAL COMPOSITION OF HSLA SME 1613 : Materials Science 2007 MECHANICAL PROPERTIES: HSLA • Much stronger and tougher than ordinary plain carbon steels. • alloying elements : alter the microstructure of plain carbon steels, which is usually a ferrite-pearlite aggregate, to produce a very fine dispersion of alloy carbides in an almost pure ferrite. • Increases the material's strength by precipitation strengthening and by refining the grain size, which in the case of ferrite increases yield strength by 50% for every halving of the mean grain diameter. SME 1613 : Materials Science 2007 Microstructure of HSLA A517 Grade A533 grade b, quenched 7,quenched from from 900C and tempered 925°C,tempered at at 620C . This is a heavy 650C = tempered section plate, the martensite. microstructure consists of ferrite and tempered bainite. SME 1613 : Materials Science 2007 Application of HSLA • Applications: include oil and gas pipelines, automotive beams, offshore structures and shipbuilding. • Also used in cars, trucks, cranes, bridges and other structures that are designed to handle a lot of stress, often at very low temperatures. SME 1613 : Materials Science 2007 SME 1613 : Materials Science 2007 Maraging Steels • Fe-Ni martensite alloys (which belong to the family of iron-base alloys)additionally alloyed with cobalt, molybdenum, titanium and some other elements. • difference between carbon steels and maraging steels is that the martensite that forms in carbon steels,when quenched, transforms to a softer more ductile material when tempered. • maraging steels are not included in the AISI numbered listings since they are not machine steels. SME 1613 : Materials Science 2007 Type of Maraging Steels Type of Maraging Steels Composition Mechanical properties ~high quality to fracture toughness and 1. 18% Nickel 18% Ni, 8% Co, 5% Mo, ease of welding. 0.9% Ti ~the strenght is maintained with increase in section thickness and also up to 350°C ~high hardness results from the intermetallic 2. 23% Nickel 23% Ni, 2.0% Al, 2.5% Ti compounds Ni3Mo and Ni3Ti. ~very high resistance to stress corrosion compared to carbon steels. 3. 12% Nickel 12% Ni, 12% Cr, Mo, ~these steels develop notch strenght higher less amount of Al and Ti than carbon steels. SME 1613 : Materials Science 2007 Heat treatment: Maraging Steel • The maraging steels are strengthened by a process of martensitic transformation, followed by age or precipitation hardening . Precipitation hardenable stainless steels are also in this group. (1) Annealing Fe-Ni alloys to 820 °C, cooling from the austenitic condition, the alloy transforms to a fine lath type martensite. (2)(3)(4)The iron-nickel martensite starts out ductile and become hard and tough with aging. Cooling in air for 1 hours and tempered at 480 °C for 3 hours • The tempering results in strong precipitation hardening owing to the precipitation of intermetallics from the martensite, which is supersaturated with the alloying elements. By analogy with the precipitation hardening in aluminum, copper and other non-ferrous alloys, this process has been termed ageing, and since the initial structure is martensite, the steels have been called mar aging . SME 1613 : Materials Science 2007 Microstructure of Maraging Steels Fe-Ni Martensite Tempered Fe-Ni Martensite • The maraging steels have high fracture toughness due to a combination of the grain size of the martensite and the dislocation density,leading to a fine precipitation.(eg,Ni3TiAl,orthorhombic Ni,Mo) • The steels can be nitrided. The corrosion resistance is only slightly improved but the 12% Cr variety has been developed for corrosion resistance. SME 1613 : Materials Science 2007 Mechanical Properties: Maraging Steel Ultra-high strength at room temperature.(yield strength=1100MPa) Simple heat treatment, which results in minimum distortion. Superior fracture toughness compared to quenched and tempered steel of similar strength level. Low carbon content, which precludes decarburisation problems. Section size is an important factor in the hardening process. Easily fabricated. Good weldability. SME 1613 : Materials Science 2007 Application: Maraging Steel • Applications : shafts, and substitute for long, thin, carburized or nitrided parts, and components subject to impact fatigue, such as print hammers or clutches. • Also commonly used: air frame and engine components,injection moulds and dies due to its high resistance of decarburisation,distortion and cracking. • Maraging steels work well in electro-mechanical components where ultra-high strength is required, along with good dimensional stability during heat treatment. SME 1613 : Materials Science 2007 SME 1613 : Materials Science 2007.
Load more

Recommended publications
  • A New Maraging Stainless Steel with Excellent Strength–Toughness–Corrosion Synergy
    materials Article A New Maraging Stainless Steel with Excellent Strength–Toughness–Corrosion Synergy Jialong Tian 1,2, Wei Wang 2,*, M. Babar Shahzad 2, Wei Yan 2, Yiyin Shan 2, Zhouhua Jiang 3 and Ke Yang 2 1 School of Materials Science and Engineering, Northeastern University, Shenyang 110004, China; [email protected] 2 Institute of Metal Research, Chinese Academy of Sciences, Shenyang 110016, China; [email protected] (M.B.S.); [email protected] (W.Y.); [email protected] (Y.S.); [email protected] (K.Y.) 3 School of Metallurgy, Northeastern University, Shenyang 110004, China; [email protected] * Correspondence: [email protected]; Tel.: +86-24-8397-8745 Received: 17 October 2017; Accepted: 8 November 2017; Published: 10 November 2017 Abstract: A new maraging stainless steel with superior strength–toughness–corrosion synergy has been developed based on an innovative concept of alloy design. The high strength–toughness combination is achieved by forming dispersive nano-sized intermetallic compounds in the soft lath martensitic matrix with a slight amount of residual austenite. The good corrosion resistance is guaranteed by exactly controlling the Co content based on understanding the synergistic effect between Co and Cr. The fine structure characteristics of two dominant strengthening precipitations including Ni3Ti and Mo-rich phases were finely characterized associated with transmission electron microscope (TEM) and atom probe tomography (APT) analyses. The relationship among microstructure, strength and toughness is discussed. The precipitation mechanism of different precipitates in the new maraging stainless steel is revealed based on the APT analysis. Keywords: maraging stainless steel; alloy design; strength and toughness; corrosion resistance; atomic probe tomography; precipitation mechanism 1.
    [Show full text]
  • Improvement in Mechanical Properties of C300 Maraging Steel by Application of VAR Process
    ARTICLE IN PRESS Vacuum 82 (2008) 521–528 www.elsevier.com/locate/vacuum Improvement in mechanical properties of C300 maraging steel by application of VAR process Seyed Reza Elmi HoseiniÃ, Hosein Arabi, Hekmat Razavizadeh Department of Metallurgy and Materials Engineering, Iran University of Science and Technology, Narmak, Tehran, Iran Received 22 November 2006; received in revised form 1 August 2007; accepted 11 August 2007 Abstract The prime objective of this research was to improve the mechanical properties of C300 maraging steels originally cast in the vaccum induction melting (VIM) and AIM furnaces by application of vaccum arc remelting (VAR) process. For this purpose two sets of C300 maraging steel with different amounts of Ti were cast in two different types of furnaces. Three bars with 1, 1.5 and 2 wt% of Ti were produced in the argon induction melting (AIM) furnace and two bars with 0.65 and 1 wt% Ti in the VIM furnace. Then all of the bars were subjected to VAR process in order to study the effects of this process on the reduction of N and O gases and inclusions, hence improvement in the mechanical properties. The results show that the total reduction of N and O gases in the bars cast in the AIM furnace was up to 40%, the amounts of inclusions irrespective of their kind reduced up to 30% while ductility and impact energy increased up to 40%. However, these parameters in the bars cast in the VIM furnace changed as follows: total gas reduction decreased by 12%, ductility and impact energy increased by 30% and 47%, respectively.
    [Show full text]
  • Structure/Property Relationships in Irons and Steels Bruce L
    Copyright © 1998 ASM International® Metals Handbook Desk Edition, Second Edition All rights reserved. J.R. Davis, Editor, p 153-173 www.asminternational.org Structure/Property Relationships in Irons and Steels Bruce L. Bramfitt, Homer Research Laboratories, Bethlehem Steel Corporation Basis of Material Selection ............................................... 153 Role of Microstructure .................................................. 155 Ferrite ............................................................. 156 Pearlite ............................................................ 158 Ferrite-Pearl ite ....................................................... 160 Bainite ............................................................ 162 Martensite .................................... ...................... 164 Austenite ........................................................... 169 Ferrite-Cementite ..................................................... 170 Ferrite-Martensite .................................................... 171 Ferrite-Austenite ..................................................... 171 Graphite ........................................................... 172 Cementite .......................................................... 172 This Section was adapted from Materials 5election and Design, Volume 20, ASM Handbook, 1997, pages 357-382. Additional information can also be found in the Sections on cast irons and steels which immediately follow in this Handbook and by consulting the index. THE PROPERTIES of irons and steels
    [Show full text]
  • Materials Technology – Placement
    MATERIAL TECHNOLOGY 01. An eutectoid steel consists of A. Wholly pearlite B. Pearlite and ferrite C. Wholly austenite D. Pearlite and cementite ANSWER: A 02. Iron-carbon alloys containing 1.7 to 4.3% carbon are known as A. Eutectic cast irons B. Hypo-eutectic cast irons C. Hyper-eutectic cast irons D. Eutectoid cast irons ANSWER: B 03. The hardness of steel increases if it contains A. Pearlite B. Ferrite C. Cementite D. Martensite ANSWER: C 04. Pearlite is a combination of A. Ferrite and cementite B. Ferrite and austenite C. Ferrite and iron graphite D. Pearlite and ferrite ANSWER: A 05. Austenite is a combination of A. Ferrite and cementite B. Cementite and gamma iron C. Ferrite and austenite D. Pearlite and ferrite ANSWER: B 06. Maximum percentage of carbon in ferrite is A. 0.025% B. 0.06% C. 0.1% D. 0.25% ANSWER: A 07. Maximum percentage of carbon in austenite is A. 0.025% B. 0.8% 1 C. 1.25% D. 1.7% ANSWER: D 08. Pure iron is the structure of A. Ferrite B. Pearlite C. Austenite D. Ferrite and pearlite ANSWER: A 09. Austenite phase in Iron-Carbon equilibrium diagram _______ A. Is face centered cubic structure B. Has magnetic phase C. Exists below 727o C D. Has body centered cubic structure ANSWER: A 10. What is the crystal structure of Alpha-ferrite? A. Body centered cubic structure B. Face centered cubic structure C. Orthorhombic crystal structure D. Tetragonal crystal structure ANSWER: A 11. In Iron-Carbon equilibrium diagram, at which temperature cementite changes fromferromagnetic to paramagnetic character? A.
    [Show full text]
  • High Performance Steel for Percussive Drilling
    TVE-K 17001 Examensarbete 15 hp 2 Juni 2017 High Performance Steel for Percussive Drilling Elin Åkerlund Jakob Jonsson Åberg Patrik Österberg Rebecka Havo Mikael Fredriksson Abstract High Performance Steel for Percussive Drilling Elin Åkerlund, Jakob Jonsson Åberg, Patrik Österberg, Rebecka Havo and Mikael Fredriksson Teknisk- naturvetenskaplig fakultet UTH-enheten Atlas Copco Secoroc AB are searching after new bulk materials for drill heads that are used in percussive drilling in order to improve their strength and durability. The Besöksadress: aim of this project is to assist Atlas Copco in this search and provide them with Ångströmlaboratoriet Lägerhyddsvägen 1 further information regarding material properties, alloying elements, suppliers, etc. Hus 4, Plan 0 A literary study was carried out in order to identify materials that had UTS and KIC Postadress: more than or equal to 1700 MPa and 70 MPa*m^1/2, respectively. Materials that Box 536 751 21 Uppsala fulfilled these criteria were T250 grade maraging steel, Cobalt free maraging steel, High cobalt maraging steel, 300 grade maraging steel, AerMet 100, AF1410, S53, Telefon: M54, 300M, 4340M and PremoMet. These were categorized into maraging steels, 018 – 471 30 03 high alloy secondary hardened steels, and low alloy steels, and were then further Telefax: researched. 018 – 471 30 00 The material with the highest combination of UTS and KIC was M54 followed by Hemsida: AerMet 100; while AF1410 had the highest KIC but a low UTS, and PremoMet had http://www.teknat.uu.se/student the highest UTS but a low KIC. Maraging steels and HASH steels have a similar price range, while low alloy steels are much cheaper.
    [Show full text]
  • A Review of Factors Affecting the Mechanical Properties of Maraging
    metals Review AReview Review of Factors Affecting the Mechanical PropertiesA Review ofof MaragingFactors Affecting Steel 300 the Fabricated Mechanical via Laser PowderProperties Bed of Fusion Maraging Steel 300 Fabricated via Laser Powder Bed Fusion Barry Mooney and Kyriakos I. Kourousis * Barry Mooney and Kyriakos I. Kourousis * School of Engineering, University of Limerick, V94 T9PX Limerick, Ireland * SchoolCorrespondence: of Engineering, [email protected]; University of Limerick, Tel.: V94+353-61202217 T9PX Limerick, Ireland * Correspondence: [email protected]; Tel.: +353-61202217 Received: 29 August 2020; Accepted: 20 September 2020; Published: 22 September 2020 Received: 29 August 2020; Accepted: 20 September 2020; Published: 22 September 2020 Abstract: Maraging steel is an engineering alloy which has been widely employed in metal additive Abstract: Maraging steel is an engineering alloy which has been widely employed in metal additive manufacturing. This paper examines manufacturing and post-processing factors affecting the manufacturing. This paper examines manufacturing and post-processing factors affecting the properties of maraging steel fabricated via laser powder bed fusion (L-PBF). It covers the review of properties of maraging steel fabricated via laser powder bed fusion (L-PBF). It covers the review of published research findings on how powder quality feedstock, processing parameters, laser scan published research findings on how powder quality feedstock, processing parameters, laser scan strategy, build orientation and heat treatment can influence the microstructure, density and porosity, strategy, build orientation and heat treatment can influence the microstructure, density and defects and residual stresses developed on L-PBF maraging steel, with a focus on the maraging steel porosity, defects and residual stresses developed on L-PBF maraging steel, with a focus on the 300 alloy.
    [Show full text]
  • High Strength X3nicomoti 18-9-5 Maraging Steel Prepared by Selective Laser Melting from Atomized Powder
    materials Article High Strength X3NiCoMoTi 18-9-5 Maraging Steel Prepared by Selective Laser Melting from Atomized Powder Angelina Strakosova *, Jiˇrí Kubásek, Alena Michalcová, Filip Pr ˚uša,Dalibor Vojtˇechand Drahomír Dvorský Department of Metals and Corrosion Engineering, Faculty of Chemical Technology, University of Chemistry and Technology, Technická 5, Praha 6—Dejvice, 166 28 Prague, Czech Republic; [email protected] (J.K.); [email protected] (A.M.); [email protected] (F.P.); [email protected] (D.V.); [email protected] (D.D.) * Correspondence: [email protected] Received: 21 November 2019; Accepted: 10 December 2019; Published: 12 December 2019 Abstract: Maraging steels are generally characterized by excellent mechanical properties, which make them ideal for various industrial applications. The application field can be further extended by using selective laser melting (SLM) for additive manufacturing of shape complicated products. However, the final mechanical properties are strongly related to the microstructure conditions. The present work studies the effect of heat treatment on the microstructure and mechanical properties of 3D printed samples prepared from powder of high-strength X3NiCoMoTi 18-9-5 maraging steel. It was found that the as-printed material had quite low mechanical properties. After sufficient heat treatment, the hardness of the material increased from 350 to 620 HV0.1 and the tensile yield strength increased from 1000 MPa up to 2000 MPa. In addition, 3% ductility was maintained. This behavior was primarily affected by strong precipitation during processing. Keywords: maraging steel; atomized powder; selective laser melting; heat treatment; precipitation hardening 1. Introduction Selective laser melting (SLM) is one of the best-known methods of additive production of materials.
    [Show full text]
  • Microstructural Analysis of Co-Free Maraging Steel Aged Aline Castilho Rodrigues1, Heide Heloise Bernardi1, Jorge Otubo2
    doi: 10.5028/jatm.v6i4.400 Microstructural Analysis of Co-Free Maraging Steel Aged Aline Castilho Rodrigues1, Heide Heloise Bernardi1, Jorge Otubo2 ABSTRACT: Maraging steels have low carbon content and are highly alloyed, having as main feature the ability to increase INTRODUCTION the mechanical strength after thermal aging. Therefore, the objective of this work is to analyze the effect of aging in a Co- Maraging steel was developed in the 1950’s, to support free maraging steel, Fe – 0.014% C – 0.3% Mn – 3.9% Mo – 2.1% Cu – 0.19% Si – 11.8% Cr – 9.1% Ni – 1.0% Ti (wt), at the demand for a low density and temperature resistant steel different heat treatment times (10 min - 960 min) at constant (250°C – 300°C), for improving aircraft performance. This new temperature (550°C), after cold rolling up to 66% and 77% material was created adding aluminum (Al) and titanium (Ti) in area reduction. Microstructures were analyzed by scanning steel with nickel (Ni). In the 1960’s, cobalt (Co) and molybdenum electron microscopy (SEM - EDS) and mechanical properties by Vickers hardness measurements. The results showed (Mo) were added into the composition of maraging steels. a significant increase in the hardness of the material after Clarence George Bieber, in International Nickey Company, aging heat treatment on the solution treated and deformed studied the addition of these elements in the alloy and concluded samples. The aging heat treatment which was harder about 650 HV was 550°C/60 min. that there is a significant increasing in mechanical resistance (Lopes, 2007; Méndez, 2000).
    [Show full text]
  • Additive Manufacturing 18 Ni Maraging Steel
    Additive Manufacturing 18 Ni Maraging Steel Designed for Processing in Laser Powder Bed Fusion (PBF-LB) Systems Applications MetcoAdd™ C300-A is an iron-nickel-cobalt based powder similar to 18 Ni ▪ Tools and dies maraging steel. The alloy chemistry is known to provide ultra high strength in ▪ Plastic injection molds combination with toughness and resistance to cracking. The composition of the ▪ Light metal and pressure die casting powder is similar to Werkstoff Nr. 1.2709 / X3NiCoMoTi 18-9-5 and AMS 6514. ▪ Cold extrusion tools Room temperature static properties of PBF-LB processed and heat treated material coupons have been shown to be comparable to those of AMS 6514. For reference purposes Oerlikon has processed MetcoAdd C300-A using fixed parameters and 40 μm layer thickness to provide data below. Additional testing has been performed by an extensive network of consortia and customer partners on a broader range of machine types. Properties may be optimized based on application specific requirements. Typical Post Heat Treatment Properties (C300-A) [1] [2] [3] Concept Laser M2 Cusing EOS M290 Test Method Ultimate Tensile Strength (MPa), XY/Z 2064±25 / 2104±15 2050±17 / 2027±9 Yield Strength (MPa), XY/Z 1982±30 / 2023±15 1996±18 / 1980±7 ASTM E8 Elongation at break %, XY/Z 5±2 / 5±3 9±1 / 8±1 Hardness (VHN300g) 594+/-15 599+/-10 ASTM E384-17 Relative Density % >99.9% >99.8% Internal Spec. [1] Disclaimer: All data published in this datasheet has been shared for reference purposes only and is not sufficient to design or certify parts.
    [Show full text]
  • Plasma Arc Remelting of Steels and Nickel-Based Superalloys N
    Plasma arc remelting of steels and nickel-based superalloys N. Sparks, J. Young, L. Shaw, Thomas Johnson To cite this version: N. Sparks, J. Young, L. Shaw, Thomas Johnson. Plasma arc remelting of steels and nickel-based superalloys. Journal de Physique IV Proceedings, EDP Sciences, 1993, 03 (C7), pp.C7-883-C7-888. 10.1051/jp4:19937137. jpa-00251757 HAL Id: jpa-00251757 https://hal.archives-ouvertes.fr/jpa-00251757 Submitted on 1 Jan 1993 HAL is a multi-disciplinary open access L’archive ouverte pluridisciplinaire HAL, est archive for the deposit and dissemination of sci- destinée au dépôt et à la diffusion de documents entific research documents, whether they are pub- scientifiques de niveau recherche, publiés ou non, lished or not. The documents may come from émanant des établissements d’enseignement et de teaching and research institutions in France or recherche français ou étrangers, des laboratoires abroad, or from public or private research centers. publics ou privés. JOURNAL DE PHYSIQUE IV Colloque C7, supplCment au Journal de Physique 111, Volume 3, novembre 1993 Plasma arc remelting of steels and nickel-based superalloys N.C. SPARKS, J.M. YOUNG, L. SHAW* and TI? JOHNSON ZRC in Materials for High Pe$ormance Applications, The University of Birmingham, Birmingham B15 2TT U.K. * special ~eltedProducts Limited, Atlas House, Atterclge Road, Shefield, S4 7W U.K. ABSTRACT. The IRC Plasma Arc Cold Hearth Remelting (PACHR) furnace has been used to produce lOOmm and 150mm diameter ingots of alloy 718, M50 bearing steel and GI 10 maraging steel from VIMIVAR feedstocks. These mals highlighted the importance of accurately controlling the level of the melt pool surface in the crucible in order to produce an acceptable ingot finish.
    [Show full text]
  • Mechanical Properties of 3D-Printed Maraging Steel Induced by Environmental Exposure
    metals Article Mechanical Properties of 3D-Printed Maraging Steel Induced by Environmental Exposure Troy Y. Ansell 1,* , Joshua P. Ricks 1, Chanman Park 1, Chris S. Tipper 2 and Claudia C. Luhrs 1 1 Mechanical and Aerospace Engineering Department, Naval Postgraduate School, Monterey, CA 93943, USA; [email protected] (J.P.R.); [email protected] (C.P.); [email protected] (C.C.L.) 2 Marine Corps Logistics Command, Marine Depot Maintenance Command, Albany, GA 31704, USA; [email protected] * Correspondence: [email protected] Received: 11 January 2020; Accepted: 31 January 2020; Published: 4 February 2020 Abstract: Changes in the mechanical properties of selective laser melted maraging steel 300 induced by exposure to a simulated marine environment were investigated. Maraging steel samples were printed in three orientations: vertical (V), 45◦ (45), and horizontal (H) relative to the print bed. These were tested as-printed or after heat-treatment (490 ◦C, 600 ◦C, or 900 ◦C). One set of specimens were exposed in a salt spray chamber for 500 h and then compared to unexposed samples. Environmental attack induced changes in the microstructural features and composition were analyzed by scanning electron microscopy and energy dispersive spectroscopy respectively. Samples printed in the H and 45◦ directions exhibited higher tensile strength than those printed in the V direction. Corrosion induced reduction in strength and hardness was more severe in specimens heat-treated between 480 ◦C and 600 ◦C versus as-printed samples. The greatest decrease in tensile strength was observed for the 45◦-printed heat-treated samples after exposure. A comparison between additive and subtractive manufactured maraging steel is presented.
    [Show full text]
  • Electrochemical Corrosion Characteristics of Maraging Steel Welds Depending on Chromium Content
    Int. J. Electrochem. Sci., 9 (2014) 4709 - 4720 International Journal of ELECTROCHEMICAL SCIENCE www.electrochemsci.org Electrochemical Corrosion Characteristics of Maraging Steel Welds Depending on Chromium Content S. W. Kim, H. W. Lee* Department of Materials Science and Engineering, Dong-A University, 840 Hadan-dong, Saha-gu, Busan 604-714, Republic of Korea *E-mail: [email protected] Received: 15 April 2014 / Accepted: 28 May 2014 / Published: 16 June 2014 The corrosion behavior of maraging steel weldments which depend on Cr content has been studied, and electrochemical experiments were conducted changing the immersion time in chloride solution. The study was carried out using open-circuit potential, potentiodynamic polarization, electrochemical impedance spectroscopy techniques. The results showed that corrosion rate decreased and Ecorr and Epit increased with increasing Cr content and also with increased with immersion time of the maraging steel before measurements. The surface morphology of the corroded samples has been examined by Scanning Electron Microscopy. It showed that the resistance to general and pitting corrosion increased as the Cr content increased. Keywords: Steel; polarization; EIS; SEM; Pitting corrosion 1. INTRODUCTION As maraging steel is comprised of low carbon (C≤0.03) Fe-Ni martensite matrix of BCC structure containing precipitation hardening alloy elements in a solid state, it is hardened by precipitation of intermetallic compounds resulting from aging at 480℃.[1] This steel of light gray color has high toughness in spite of its high strength. Many applications of maraging steels in aerospace, marine, and nuclear power fields as well as for special parts of industrial machines have been realized due to their unique combination of superior mechanical properties, fabrication, weldability and corrosion resistance.
    [Show full text]