Aluminized Glass Cloth

Total Page：16

File Type：pdf, Size：1020Kb

1 MATERIAL SAFETY DATA SHEET – Foil / Glass Cloth GLT Products Date Prepared: 09/27/05 6810 Cochran Road Emergency Phone: Chem-Tel 800/255-3924 Solon, OH 44139 Information Phone: 440/914-1122 Section 1 – Material Identification Product Name: Foil / Glass Cloth Manufacturer: Great Lakes Textiles 7200 Northfield Road Walton Hills, OH 44146 Section 2 – Hazardous Ingredients Ingredients CAS No. TLV/PEL Aluminum Foil 7429-90-5 - Fiberglass Fabric 65997-17-3 15.0 mg/m 3 Polymeric Adhesive No information *Hazardous Ingredients CAS No. OSHA ACGIH Other Limits PEL TLV Recommended Glass Fiber 65997-17-3 150.0 mg/m 3 5.0 mg/m 3 * Substances listed in the hazardous ingredients section are those that have been determined to be health hazards and are present at the concentration of 1% or greater r 0.1% if the substance is on the list of potential carcinogens cited in the OSHA Hazard Communication Standard. Section 3 – Physical/Chemical Characteristics Boiling Point: N/A Melting Point: N/A Vapor Pressure: N/A Vapor Density: N/A Solubility (in water): Insoluble in Water Appearance: Aluminum Foil/Glass Fabric Lamination Odor: No Odor Specific Gravity: Not Determined Section 4 – Fire and Explosion Hazard Data 08/25/06 Great Lakes Textiles Foil/Glass Cloth 2 MATERIAL SAFETY DATA SHEET – Foil / Glass Cloth Flash Point: N/A Method used: N/A Flammability Limits: LEL – Not Applicable UEL – Not Applicable Auto Ignition Temperature: N/A Extinguishing Media: Foam, dry chemical, fog or water Special Fire Fighting Instructions: Fires involving this product should be fought while wearing self-contained breathing apparatus. Unusual Fire and Explosion Hazards: None Section 5 - Reactivity Data Stability: Stable Hazardous Decomposition Products: Under fire conditions, products will decompose and produce formic and acetic acid, acetaldehyde, acrolein, nitrogen oxides, carbon monoxide, carbon dioxide and other organic vapors. Hazardous Polymerization: Should not occur under normal use. 08/25/06 Great Lakes Textiles Foil/Glass Cloth .

Copy Link

Recommended publications

Using Sig Glass Cloth and Glass Resin in Model Building
USING SIG GLASS CLOTH AND GLASS RESIN IN MODEL BUILDING Both Fiberglass Cloth and Polyester Resin have found numerous, where the cloth will come. Place the cloth on the joint and work it into valuable uses in the model aircraft field. Fiberglass cloth is very fine the resin until it is saturated. Brush a coat of resin over the cloth and filaments of pure glass spun into yarn. This yarn is then woven into vary• feather it out into the wood. Allow to cure three or four hours and sand ing weights of cloth and is also available as bulk fiber for converting until smooth, finishing model in normal manner. resin to a casting material. When a wire landing gear is used on a profile model, use a strip of cloth As we are chiefly interested in its application to model aircraft, Sig Glass over the wire at all points where it contacts the fuselage and attach with Cloth is of very light weight, but several layers may be used to obtain any resin in the manner described above. desired strength. Sig Glass Resin was selected for us by an outstanding MOLDING WITH FIBERGLASS authority in the fiberglass industry to meet model builder's needs and Fuselages, cowlings, wheel pants, etc., can be molded with glass cloth has many special features. and resin. For example, let's mold an engine cowling, always a problem GENERAL INSTRUCTIONS on a scale model. Carve an exact pattern from balsa and sand. Apply two Glass Resin alone will not harden. An accurate amount of hardener must or three coats of Glass Resin to the mold, sanding between each coat.
[Show full text]
Dry Self-Lubricating Composites
Composites: Part B 27B (1996) 459-465 Copyright © 1996 Elsevier Science Limited Printed in Great Britain. All rights reserved ELSEVIER PII: S1359-8368(96)00012-1 1359-8368/96/$15.00 Dry self-lubricating composites Shin Jen Shiao and Te Zei Wang National Chiao Tung University,/nstRute of Appfied Chemistry, 1001 Ta Hsue Road, Hsinchu, Taiwan 300, ROC (Received 20 February 1995; accepted 19 February 1996) Chopped strand carbon fibers, glass fibers and their hybrids were used to reinforce an epoxy matrix to which additives of PTFE, graphite and molybdenum disulfide were used for producing a dry self-lubricating material. Their tribology properties were studied using testing machines of thrust and journal radial. Also, the PV value, friction coefficient, wear rate and the contact surface temperatures were determined. The com- pression strength of the bush ring and the impact strength of material were evaluated. The surfaces of wear were investigated. The mode of fracture mechanism is proposed according to the specimens morphology. The relationship between friction coefficient and loading correlated well with the Myoshis equation in the case of a backing material. This study provided an optimal approach of making dry wear bearings by glass fibers backing at low friction coefficient. Copyright © 1996 Elsevier Science Limited (Keywords: epoxy/CF; dry self-lubrication) INTRODUCTION This study explored the use of chopped carbon fibers as the inner layer reinforcement, backed with glass cloth or The friction coefficient of a polymer has low tribology a glass mat in the outer layer in a high rate. Some properties that have been recently used as the parts of additives, such as PTFE and molybdenum disulfide, in bearing, gear and oil sealing.
[Show full text]
Fabrics Hdbk Insidernd5.Indd
Technical Fabrics Handbook Technical HexForce™ Reinforcements Woven Fabrics Unidirectional Fabrics Non-Woven Fabrics Glass Carbon Aramid Hybrids REINFORCEMENTS FOR COMPOSITES MANUFACTURING, SALES AND CUSTOMER SERVICE Seguin, Texas 1913 N. King St. Seguin, TX 78155 United States Telephone: (830) 379-1580 Fax: (830) 379-9544 Customer Service Toll Free (866) 601-5430 (830) 401-8180 Technical Service for Composite Reinforcement Fabrics MANUFACTURING For European sales ofﬁ ce numbers and a full address list, please go to: http://www.hexcel.com/contact/salesofﬁ ces Les Avenieres, France Z.I. Les Nappes 38630 Les Avenieres France www.hexcel.com INDUSTRIAL DISCLAIMER 2 For Industrial Use Only - In determining whether the material is suitable for a particular application, such factors as overall product design and the processing and environmental conditions to which it will be subjected should be considered by the User. The following is made in lieu of all warranties, expressed or implied: Seller’s only obligations shall be to replace such quantity of this product which has proven to not substantially comply with the data presented in this bulletin. In the event of the discovery of a nonconforming product, Seller shall not be liable for any commercial loss or damage, direct or consequential arising out of the use of or the inability to use the product. Before using, User shall determine the suitability of the product for their intended use and User assumes all risks and liability whatsoever in connection therein. Statements relating to possible use of our product are not guarantees that such use is free of patent infringement or that they are approved for such use by any government agency.
[Show full text]
Choosing the Right Resin for the Job
CHOOSING THE RIGHT RESIN FOR THE JOB Polyester and Epoxy resins have certain things in common, but each also has its own characteristics: POLYESTER IS IDEAL: EPOXY RESIN IS IDEAL: -As a repair for all kinds of surfaces, such as plaster, - When superior adhesion and strength is necessary. fiberglass, aluminum and wood (except redwood and Excellent adhesion to metals, woods, glass, rubber, and close-grained woods like oak or cedar. Do not use with fiberglass. Styrofoam.) - Provides excellent bond between non-porous surfaces, - For structural repairs using fiberglass cloth or mat like metals including aluminum. where high impact resistance is critical - As a tough coating or repaid material for most surfaces - As a protective, waterproof coating and sealer. including Styrofoam, redwood, cedar and oak. - The hardener for polyester resin can be increased or - Where a smooth glossy surface is important. Epoxy is decreased according to instructions, depending on however, more expensive than polyester resin and temperature. Cooler temperatures require more requires more care when mixing and applying. catalyst, warmer temperatures less. - Very low shrinkage. 100% reactive. Low VOC - Polyester is economical and easy to use. - Epoxy should be used at room temperature (70-90f); - High shrinkage factor otherwise rate of cure may be affected. The user should not attempt to adjust the ratio of hardener to resin. NOTE: Polyester resins cannot be used to repair thermoplastics; that is, the kind from which Tupperware - The hardener should be used as directed with the or molded toys like “Big Wheels” are made. epoxy resin. The two parts should be measured into a Thermoplastics include polyethylene, polypropylene, mixing container, not simply dumped together, even acrylic, PVC, and ABS.
[Show full text]
Manufacturing, Application and Development of PTFE/Teflon Coated Fiber Glass Fabric
Manufacturing, application and development of PTFE/Teflon coated fiber glass fabric PTFE/Teflon coated fiber glass fabric is made of glass fiber cloth as the substrate, impregnated with PTFE dispersion. Impregnated fiberglass cloth surface, coated with a thin layer of fluororesin small particles, and then through the drying, baking, sintering and other processes, the dispersion of volatile and leaving F4 tiny particles, tightly attached to the surface and pores of the fiber glass cloth, intensive continuous as a whole, to achieve the purpose of fiberglass cloth and F4 firm bonding, it become a new material which not only has the characteristics of fiber glass, but also has many excellent properties of fluorine plastic. According to different needs, in the dispersion can also be added inorganic or organic filler, to further improve its electrical properties, anti-aging properties and wear resistance, add a different pigment and then increase its excellent decorative performance. Process Research Raw material A. PTFE commonly known as “plastic king”, it is one of the best performance varieties of plastic. It has excellent temperature resistance and corrosion resistance, excellent insulation properties, non-stick, non-toxic and odorless, harmless to the human body. B. Fiberglass fabric The substrate of the coated materials should have high temperature resistance and good tensile strength, glass fiber compared with natural fibers and chemical fiber, it has high strength, elongation is small, good chemical stability, etc., and it can make up for the lack of F4, to maintain the size of the stability. Production process and key technology A. Production process Treated fiberglass fabric and F4 dispersion liquid → Impregnation → Drying → Take-up → Sintering → Take-up → Checking → Finished product pakcaging → Storage B.
[Show full text]
Shiny Glass Cloths
Shiny Glass Cloths Smooth texture of the glass cloth easily releases particles with rinsing. This cloth also reduces the amount of chemicals needed for cleaning. Studies by the EPA have found that microfiber cloths eliminated 94% of bacteria from surfaces (compared to the 68% reduction by regular mops.) Using Monarch Brands color coding system eliminates any guesswork from what product should be used when. Which means microfiber that is used to clean guestroom toilets will never be used to clean vanities. Our microfiber cloths are lint-free and can be laundered up to 500 times. Details Part Number GSM Grams/Piece Color Size/Inches Case Count M915160B 20 44 Blue 16 x 16 15 Dozen/Case M915160GLD 20 44 Gold 16 x 16 15 Dozen/Case M915160GRY 20 44 Grey 16 x 16 15 Dozen/Case Technical Specifications Pass Acceptable Fail Size Tolerance Weight Tolerance Dimensional Stability Dimensional Stability L +/- 1% +/- 1% to Washing - MD 6% to Washing - CD 2% 10+ 8+ 6+ 4+ 2+ 0 -2 -4 -6 -8 -10 10+ 8+ 6+ 4+ 2+ 0 -2 -4 -6 -8 -10 10+ 8+ 6+ 4+ 2+ 0 -2 -4 -6 -8 -10 10+ 8+ 6+ 4+ 2+ 0 -2 -4 -6 -8 -10 Breaking Strength Breaking Strength Color Shade Color Fastness to Washing length 790 N width 1070 N 4 2-3 100 200 300 400 500 600 700 800 200 600 1000 1040 1080 1 2 3 4 5 1 2 3 4 5 Color Fastness to Rubbing Color Shade Variation Elongation - MD Elongation - CD 3 after 5 washes 4 127.00% 212.00% 0 50 100 150 0 50 100 150 200 250 1 2 3 4 5 1 2 3 4 5 Absorption Speed Total Absorption 1 s 162% 0 1 2 3 4 5 100 200 300 400 500 600 700 800 11350 Norcom Road, Philadelphia, PA 19154 • (215) 458-5744 • www.monarchbrands.com The standards that we are measured by are globally-recognized.
[Show full text]
Processing of Composite Laminates
3 Processing of Composite Laminates 3.1 IntroductionCopyrighted Material – Taylor & Francis The processing of polymer matrix composite laminates has been the subject of considerable research during the last several decades (see Lee et al. 1982, Loos and Springer 1983, Bogetti and Gillespie 1991, and Khoun et al. 2010). Multiple physical and chemical phenomena must occur simultaneously and in the proper sequence to achieve desired laminate properties. There are several routes to achieve full consolidation and minimize void content of a polymeric matrix with a reinforcing fiber in volume fractions (50–65%) appropriate for structural applications. The most widely accepted approach is by impregnation of unidirectional fibers, textile fabrics, or random fiber arrays to create a thin sheet or tape. If the polymer is a thermoset, it is often advanced in its curing state to the “B” stage (a state of cure of the matrix that is incomplete but provides high room temperature viscosity). Known as prepreg in this form, it may be stored at low temperature (below freezing) to greatly reduce the rate of cure and thus increase the storage life. After being warmed to room temperature, these prepreg sheets or tapes may then be assembled into a laminate and subjected to a cure cycle. It is also possible to assemble dry fibers into an appropriate geometric form and then impregnate the entire laminate in a single step. This approach is known as resin transfer molding (RTM) or resin infusion, and there are sev- eral variations, such as vacuum-assisted resin transfer molding (VARTM). The weaving of a fabric from reinforcing fibers is a widely accepted approach to creating the fiber preform, although there are other techniques designed to avoid fiber crimp and develop microstructures typical of that achieved with prepreg tape.
[Show full text]
Electrical Shorting Between the Carbon-Fiber Cloth Electrodes of Structural Capacitors with a Glass-Fiber Cloth Separator*
Open Journal of Composite Materials, 2014, 4, 140-147 Published Online July 2014 in SciRes. http://www.scirp.org/journal/ojcm http://dx.doi.org/10.4236/ojcm.2014.43016 Electrical Shorting between the Carbon-Fiber Cloth Electrodes of Structural Capacitors with a Glass-Fiber * Cloth Separator Akira Todoroki1, Hiroko Shiomi2, Yoshihiro Mizutani1, Yoshiro Suzuki1 1Department of Mechanical Sciences of Engineering, Tokyo Institute of Technology, Tokyo, Japan 2Tokyo Institute of Technology, Tokyo, Japan Email: [email protected] Received 13 June 2014; revised 28 June 2014; accepted 7 July 2014 Copyright © 2014 by authors and Scientific Research Publishing Inc. This work is licensed under the Creative Commons Attribution International License (CC BY). http://creativecommons.org/licenses/by/4.0/ Abstract Multifunctional composites that have the ability to store or generate energy have attracted huge attention recently. One type of multifunctional composite is a structural capacitor that uses car- bon fiber cloth as electrodes separated by glass-fiber cloth. However, such structural capacitors are difficult to fabricate reliably because electrical shorts sometimes form between the electrodes. In the present study, we investigate the mechanism of electrical shorting in such capacitors, which allows us to propose an improved fabrication process to prevent electrical shorting between the carbon-cloth electrodes. Infrared thermography reveals that electrical shorting between the elec- trodes is caused by contact between the carbon-fiber electrodes. Such contacts are formed by movement of the glass fibers of the separator during curing, which is induced by epoxy resin flow. Pre-curing of the glass-fiber cloth separator to a suitable degree ensures that the electrical insula- tion between carbon-fiber electrodes is reliable.
[Show full text]
Dictionary of Textiles by Harmuth Louis
PICTIONI\RY GIFT OF J DICTIONARY OF TEXTILES B Y LOUIS HARMUTH FASHION EDITOR OF "WOMEN'S WEAR" 1915 FAIRCHILD PUBLISHING COMPANY NEW YORK FAIRCHILD PUBIISHING CO, Copyright 1915. PREFACE The tendency in modern books of a technical character undoubtedly in- clines very strongly toward encyclopedic and dictionary forms. The cry for the saving of lime calls for books in compact form with information handy at a moment's notice. The present DICTIONARY is the result of 7'/2 years of collecting and compiling information, gained to a large extent in connection with my work on the Daily Trade Record and Women's Wear. With over 6,600 terms and definitions contained in it, this DICTIONARY is as nearly com- plete, in number of terms strictly relating to textile fibres and fabrics, as it is possible for a work of this kind to be. It was my desire to present in the DICTIONARY and within as small compass as practical the largest number of terms and definitions possible, re- lating to textiles from the fibres to the finished fabrics and everything which goes into them in the course of the manufacture. An interesting part of the DIC- TIONARY contains names of fabrics, now obsolete, with as complete a de- scription of their character as it was possible to find in various old laws, wills, lists and in the technical literature. Owing to the fact that manufacturers con- stantly have recourse to some obsolete fabric in search of new effects, details of manufacturing and finishing of such materials ought to be interesting.
[Show full text]
Glass Cloth / Phenolic Resin) This Material Is Produced from Woven Fiberglass Cloth and High-Temperature Phenolic Resin
TECHNICAL DATA SHEET G-3 (Glass Cloth / Phenolic Resin) This material is produced from woven fiberglass cloth and high-temperature phenolic resin. It is flexible, compressible and has impact good strength. GENERAL DESCRIPTION Phenolic Laminates are produced by applying heat and pressure to layers of paper, canvas, linen or glass cloth impregnated with synthetic thermosetting resins. When heat and pressure are applied to the layers, a chemical reaction (polymerization) transforms the separate layers into a single laminated material with a “set” shape that cannot be softened again -- therefore, these materials are called “Thermosets”. A variety of resin types and cloth materials can be used to manufacture thermoset laminates with a range of mechanical, thermal, and electrical properties. TYPICAL PROPERTIES of GLASS LAMINATES (SHEET FORM) Benefits ( mechanical properties of rod and tube forms may differ ) Heat Resistance Mechanical strength ASTM or UL G-5/G- Property G-3 G-7 G-10 G-11 test 9 Low thermal expansion PHYSICAL Density (lb/in³) 0.065 0.067 0.065 0.065 0.065 D792 Applications (g/cm³) 1.80 1.85 1.80 1.80 1.80 Slot insulator D570 Water Absorption, 24 hrs (%) 2.65 0.60 0.10 0.10 0.20 Seal MECHANICAL Tensile Strength (psi) Gasket D638 -lengthwise 42,000 61,600 20,000 45,000 43,000 Valve plate -crosswise 34,000 51,100 - 38,000 37,000 Flexural Strength (psi) D790 -lengthwise 40,500 61,600 30,000 75,000 80,000 -crosswise 34,000 51,100 - 65,000 70,000 Flexural Modulus (Kpsi) D790 -lengthwise 1,800 2,000 1,600 2,700 3,000 -crosswise 1,400
[Show full text]
Cotton and Linen
.r»'^- MERCHANDISE MANUAL SERIES : t 2XT. .2 C0TT0N5»mEN THOMPSON MMiMm rW LIBRARY School of Business MERCHANDISE MANUAL SERIES COTTON AND LINEN BY ELIZA B. THOMPSON Instructor in Salesmanship, High School, New Haven. Conn.; formerly Store Teacher, Stem Brothers, New York City, and A. I. Namm & Son, Brooklyn, N. Y.; Instructor of Textile Merchandise Courses, New York Univereity NEW YORK THE RONALD PRESS COMPANY 1922 INTENTIONAL SECOND EXPOSURE MERCHANDISE MANUAL SERIES COTTON AND LINEN BY ELIZA B. THOMPSON Instructor in Salesmanship, High School, New Haven, Conn.- formerly Store Teacher, Stern Brothers, New York City, and A. I. Namm & Son, Brooklyn, N. Y.; Instructor of Textile Merchandise Courses, New York University NEW YORK THE RONALD PRESS COMPANY 1922 Zfiii Attita in Sebitateb to Mrs. Henry Ollesheimer, Miss Copyright, 1917, by Virginia Potter, and Miss Anne The Ronald Press Company Morgan, who desiring to give greater opportunity for advance- ment to commercial Copyright, 1922, by employees and believing that all business The Ronald Press Company eflficiency must rest upon a solid foundation reserved AU rights of training and education gave years of enthusiastic service to the testing of this belief. 154-. 53 .y T3 7 EDITOR'S PREFACE As "Department Store Merchandise Manuals" these SERIES books were MERCHANDISE MANUAL originally written for salespeople and were designed to give them reliable information concerning EDITOR OF SERIES the sources and manufacturing processes of M.A. the mer- BEULAH ELFRETH KENNARD, chandise which they handle. When it was Department Store Courses. New York necessary Formerly Director of Courses to deal Clmirman of Committee on Merchandise with scientific or historical Un^ersity; Educational Director, material it was fo? nIw YOTk City Public Schools; Department Store Education Association treated as simply and concretely as possible and the pomt of view taken was that of CONSULTING EDITOR business rather than that of the school or laboratory.
[Show full text]
Adhesive Tapes for Electrical Insulation of Transformers, Spools, Electric Motors, Printed Circuit Boards Etc
Adhesive Tapes for Electrical Insulation of Transformers, Spools, Electric Motors, Printed Circuit Boards etc. Self Adhesive Tapes Adhesive Tapes for Electrical Insulation ) ) bility No. s ) - ( Ω VDE 0303 ) VDE 25mm) Specification File - - / eff mega Product Backing Type Adhesive Thcickness Backing (mm) Total Thickness (mm) Colour to steel Adhesion (N/25mm Strength Tensile (N break at Elongation (%) Voltage Breakdown (V Resistance Insulation ( Electrolytic Corrosion Flamma RoHS UL UL Insulation Class A 105°C Paper 54353 Paper R 0,09 0,130 Beige 7,50 75,00 9 800 - - - - - 3053 Paper R - 0,170 Beige 27,50 287,50 10,5 - - - - - - 51337 Paper AT 0,159 0,230 Beige 14,80 236,00 4 1870 1,0 - - - - Silk Acetate Cloth Tapes 5060 White Silk acetate cloth RT 0,180 0,260 10,00 150,00 20 2500 - - - E338128 PV1 Black Insulation Class B 130°C Polyester Film Black Polyester Film RT 0,025 0,056 13,75 110,00 100 5000 106 A1,0 BU1 E20780 51587 Yellow 6 51588 Polyester Film RT 0,025 0,056 Clear 13,75 110,00 100 5000 10 A1,0 BU1 E20780 Polyester Film RT 0,025 0,051 Yellow 12,30 110,00 100 5000 105 A1,0 BU1 E20780 51594 6 54107 Polyester Film RT 0,025 0,060 Yellow 11,00 110,00 100 5000 10 A1,0 BU1 E20780 Polyester Film RT 0,025 0,060 Beige 13,75 110,00 100 5000 106 A1,0 BU1 E20780 54108 50501 6 (1) Polyester Film AT 0,025 0,055 7 Colours* 11,00 100,00 80 5000 10 A1,0 BU1 E338128 Yellow Polyester Film A 0,025 0,056 9,60 110,00 100 5000 106 A1,0 BU1 E20780 51589 Clear Yellow 54113 Polyester Film AT 0,025 0,060 12,30 110,00 100 5000 106 A1,0 BU1
[Show full text]