TTEPCI Card The 1 Gbit/s TTEthernet Network Board

The TTEPCI Card brings the full power of KEY FEATURES/BENEFITS time-triggered communication technology to the PCI form factor. The • Supports 1 Gbit/s full duplex Ethernet links TTEthernet technology enables hard real-time • Standard PCI form factor end system for operation in distributed systems based on use in lab environments Ethernet networks. • Supports up to 3 channels using SFP

connectors PCI Form Factor Pluggable Mezzanine Card • Three TTEthernet traffic classes are supported Altera Stratix IV (EP4SGX) by TTEPCI Card: • Compliant to TTEthernet 1.0 specification • Time-triggered traffic with hard real-time guarantee and transport delay jitter in sub-microsecond range • Rate-constrained traffic with guaranteed bandwidth (ARINC 664-based send and receive operation, no traffic shaping) • Standard (COTS) Ethernet traffic Compatible with IEEE 802.3 Ethernet The TTEPCI Card network interface card The card can be used in PCI plugged on various implements the distributed fault-tolerant clock PCs or embedded systems for lab use or for field synchronization algorithm of TTEthernet in applications. It is built using a TTEPMC Card and a hardware. passive PCI carrier board.

TTEPCI Card is a PCI form factor pluggable TTEPCI Card transmits time-critical and mezzanine card for network communication. safety-critical data in a secure way and according It combines the IEEE 802.3 Ethernet standard for to a predefined schedule. Apart from that it is with the safety-critical time- compatible with IEEE 802.3 Ethernet and enables TTE triggered technology of TTTech. PCI Card data traffic with a bandwidth of up to 1 Gbit/s. enables real-time Ethernet communication between an embedded computer and TTESwitches TTEPCI Card is available in a lab version supporting for redundant channels in a safety-critical system. up to three SFP channels.

Key Features Dimensions • Compliant to TTEthernet 1.0 specification • Size: 212 x 127 (in mm) • Supports 1 Gbit/s full duplex Ethernet links • Weight: 350 g • Standard PCI form factor end system for use in lab environments Bus Interfaces • Supports up to 3 channels using SFP • 32 bit 33 MHz PCI 3.3V connectors • Altera Stratix IV (EP4SGX) Power Supply • 256 Mbit Flash • +12 V Supply from J2 connector • Supported software driver (PCI / Linux) • +3.3 V Supply from J2 connector • DMA Support • JTAG support on board Environmental Operating Ranges • Conduction cooled board design • Lab equipment • Operating temperature: 0 to 40 °C Hardware Features • Non-operating temperature: -40 °C to 100 °C • Operating/Non-operating humidity: Form Factor humidity level from 25 to 90 % • 32 bit PCI Versions Connectivity • Basic Lab Version • Host Interfaces: Lab Version with 3 SFP cages (no magnetics, 32 or 64-bit 33 MHz PCI 3.3V no PHYs) • Front Connectors: Up to 3 ports 100/1000 Mbit/s SFPs Software Support • A Linux driver is available (64 bit/32 bit Linux). Environment • Lab environment Packaging Contents • Passive cooler • TTEthernet PCI Card hardware board • User Manual TTEthernet End System • Linux driver • The FPGA implements the TTEthernet End System IP with 3 channels. Order Number TTE • 12097: PCI Card (3x optical SPFs) TTEthernet Connections • 12098: TTEPCI Card (3x copperl SPFs) • Up to 3 Ports 1 Gbit/s SFPs • Connectors as faceplate I/Os

TTTech Contact Information www.tttech.com

Europe, Austria - Headquarters North America, USA Japan China Tel.: +43 1 585 34 34-0 Tel.: +1 978 933 7979 Tel.: +81 52 485 5898 Tel.: +86 21 5015 2925

E-mail: [email protected]

Copyright © TTTech Computertechnik AG. All rights reserved. All trademarks are the property of their respective holders. D-STRATPHY-E-04-003-V1.3 To the extent possible under applicable law, TTTech Computertechnik AG hereby disclaims any and all liability for the content and use of this flyer.