Shellfish Pollution Reduction Programme

As required by Article 5 of the Shellfish Water Directive 2006/113/EC and Section 6 of the Quality of Shellfish Waters Regulations, 2006 (S.I. No. 268 of 2006)

Characterisation Report Number 21

McSWYNES BAY SHELLFISH AREA COUNTY

2 TABLE OF CONTENTS

LIST OF FIGURES ...... 4 LIST OF TABLES...... 5 ABBREVIATIONS ...... 6 1.0 INTRODUCTION ...... 7 1.1 Aims and responsibility ...... 7 1.2 Shellfish water quality parameters...... 7 1.3 Designated shellfish areas...... 10 1.4 Development of Shellfish Pollution Reduction Programmes ...... 11 1.5 Assessment of Shellfish Pollution Reduction Programmes...... 11 1.6 Links with the River Basin Management Plans...... 12 1.7 Layout of the Shellfish Pollution Reduction Programmes ...... 12 2.0 GENERAL CHARACTERISTICS ...... 14 2.1 Protected areas ...... 14 2.2 Shellfish growing activity...... 14 3.0 WATER QUALITY IN THE SHELLFISH AREA...... 16 4.0 CHARACTERISATION MAPS ...... 18 5.0 PRESSURES...... 51 5.1 Marine Pressures...... 53 5.1.1 Point source pressures...... 54 Marine finfish farms ...... 54 5.1.2 Morphology pressures...... 54 Fishing gear activity...... 54 Structures and associated activities...... 55 Physical modifications...... 56 5.2 Land-based Pressures...... 58 5.2.1 Point Source Pressures...... 59 Abstractions ...... 59 Water Treatment Plants...... 59 Integrated Pollution Prevention and Control Industries...... 60 Section 4 Licensed Industries ...... 61 Quarries, mines, landfills and contaminated lands ...... 62 5.2.2 Diffuse Source Pressures ...... 63 On-site waste water treatment systems...... 63 Agriculture ...... 63 Forestry ...... 64 5.2.3 Morphology Pressures ...... 66 Structures ...... 66 5.3 Summary of Key Pressures...... 67 5.3.1 Key Pressures...... 67 5.3.2 Potential Secondary Pressures ...... 67

3 LIST OF FIGURES

FIGURE 1 - 63 designated shellfish areas...... 10 MAP 1 - Designated shellfish area ...... 22 MAP 2 - Licensed shellfish areas ...... 23 MAP 3 - Contributing catchment...... 24 MAP 4 - Topography...... 25 MAP 5 - Soil wetness ...... 26 MAP 6 - Vulnerability of groundwater to pathogens from subsoil discharges ...... 27 MAP 7 - Vulnerability of groundwater to phosphorus from subsoil discharges ...... 28 MAP 8 - Vulnerability of surface waters to pathogens from subsoil discharges...... 29 MAP 9 - Vulnerability of surface waters to phosphorus from subsoil discharges ...... 30 MAP 10 - Likelihood of inadequate percolation in sub-soils...... 31 MAP 11 - Designated protected areas ...... 32 MAP 12 - WFD surface water status ...... 33 MAP 13 - Diffuse risk assessment...... 34 MAP 14 - Licensed finfish areas ...... 35 MAP 15 - Fishing gear activity...... 36 MAP 16 - Marine structures ...... 37 MAP 17 - Marine physical modifications...... 38 MAP 18 - Municipal waste water systems ...... 39 MAP 19 - Pig units and finfish farms ...... 40 MAP 20 - Industrial point source pressures...... 41 MAP 21 - On-site waste water systems ...... 42 MAP 22 - Dairy and drystock livestock units...... 43 MAP 23 - Nitrogen fertiliser usage...... 44 MAP 24 - Phosphorus fertiliser usage ...... 45 MAP 25 - Forestry types with acidification risk areas ...... 46 MAP 26 - Forestry types with eutrophication risk areas ...... 47 MAP 27 - Forestry types with sedimentation risk areas...... 48 MAP 28 - Freshwater structures ...... 49 MAP 29 - Freshwater physical modifications ...... 50

4 LIST OF TABLES

TABLE 1 - Parameters listed in Annex I of the Shellfish Water Directive...... 7 TABLE 2 - Licensed shellfish areas ...... 15 TABLE 3 - List of maps ...... 18 TABLE 4 - Summary of pressures...... 52 TABLE 5 - Finfish farms...... 54 TABLE 6 - Fishing gears...... 54 TABLE 7 - Marine morphology structures...... 55 TABLE 8 - Physical modifications...... 56 TABLE 9 - Heavily modified waters...... 56 TABLE 10 - Abstractions ...... 59 TABLE 11 - Water treatment plants...... 59 TABLE 12 - Integrated Pollution Prevention Control Licenses...... 60 TABLE 13 - Section 4 Licenses ...... 61 TABLE 14 - Quarries, mines, landfills and contaminated lands ...... 62 TABLE 15 - On-site waste water treatment systems...... 63 TABLE 16 - Livestock units and chemical fertiliser usage...... 63 TABLE 17 - Forestry types...... 64 TABLE 18 - Natural and man-made barriers ...... 66

5 ABBREVIATIONS

AA Appropriate Assessment BOD Biochemical Oxygen Demand CFB Central Fisheries Board CSO Combined Sewer Overflow DED District Electoral Division DEHLG Department of Environment Heritage and Local Government DO Dissolved Oxygen EPA Environmental Protection Agency EU European Union Ha Hectare IPPC Integrated Pollution Prevention Control Kg Kilogram LU Livestock Units NACE European industrial activity classification MI Marine Institute NPWS National Parks and Wildlife Service OSWWTS On-Site Waste Water Treatment System P.E. Population Equivalent PRP Pollution Reduction Programme RBD River Basin District RBMP River Basin Management Plan SAC Special Area of Conservation SEA Strategic Environmental Assessment SFPA Sea Fisheries Protection Authority SPA Special Protection Area SWMC Shellfish Waters Management Committee TCE Tetrachloroethylene WFD Water Framework Directive WSIP Water Services Investment Programme WTP Water Treatment Plant WWTP Waste Water Treatment Plant

6 1.0 INTRODUCTION

Article 5 of the Shellfish Directive (2006/113/EC) and section 6 of the Quality of Shellfish Waters Regulations (S.I. No. 268 of 2006) require the development of Pollution Reduction Programmes (PRPs) for designated shellfish areas in order to support shellfish life and growth and to contribute to the high quality of directly edible shellfish products. Shellfish PRPs relate to bivalve and gastropod molluscs, including oysters, mussels, cockles, scallops and clams. They do not cover shellfish crustaceans such as crabs, crayfish and lobsters.

1.1 Aims and responsibility

The objectives of Shellfish PRPs are to:

• Protect or improve water quality in designated shellfish areas; • Achieve compliance with water quality parameter values outlined in Annex I of the Shellfish Waters Directive (2006/113/EC) and Schedules 2 and 4 of the Quality of Shellfish Waters Regulations (S.I. No. 268 of 2006); • Determine the factors responsible for any non-compliances with the water quality parameter values; and • Ensure that implementation of the Shellfish PRPs does not lead, directly, or indirectly, to increased pollution of coastal and brackish waters.

Under the Regulations, the Department of Communications, Marine and Natural Resources is responsible for the development of Shellfish PRPs. However, this responsibility was transferred to the Department of the Environment, Heritage and Local Government (DEHLG) on 5th November 2008. An Inter-Departmental /Inter Agency Shellfish Waters Management Committee (SWMC) supports the Department in the development of the Shellfish PRPs.

The Regulations also place an obligation on every public authority to perform its functions in a manner that promotes compliance with the Directive and the Regulations, and to take such actions as are necessary to secure compliance with the Directive and the Regulations and with the Shellfish PRPs.

1.2 Shellfish water quality parameters

Compliance with the directive is measured against achievement of shellfish water quality parameter values outlined in Annex I of the Shellfish Waters Directive (2006/113/EC) and Schedules 2 and 4 of the Quality of Shellfish Waters Regulations (S.I. No. 268 of 2006). Table 1 summarizes these values. Mandatory (I) values must be fully achieved while it must be endeavoured to achieve guideline values (G).

TABLE 1 - Parameters listed in Annex I of the Shellfish Water Directive Physical Guideline Values (G) Mandatory Values (I) pH 7 – 9 pH units (pH units) Temperature (°C) A discharge affecting shellfish No mandatory value set in the waters must not cause the Directive fh

7 temperature of the waters to exceed by more than 2°C the temperature of waters not so affected Colouration A discharge affecting shellfish waters (after filtration) must not cause the colour of the waters (mg Pt/l) after filtration to deviate by more than 10 mg Pt/l from the colour of unaffected waters Suspended Solids A discharge affecting shellfish waters (mg/l) must not cause the suspended solid content of the waters to exceed the content in unaffected waters by more than 30% Salinity 12 to 38% ≤ 40% (%) A discharge affecting shellfish waters must not cause their salinity to exceed the salinity of unaffected waters by more than 10% Chemical Guideline Values (G) Mandatory Value (I) Dissolved oxygen ≥ 80% ≥ 70% (Saturation %) Should an individual measurement indicate a value lower than 70%, measurements shall be repeated An individual measurement may only indicate a value of less than 60% if there are no harmful consequences for the development of shellfish colonies Petroleum Hydrocarbons must not be present in hydrocarbons the shellfish water in such quantities as to: - produce a visible film on the surface of the water and/or a deposit on the shellfish - have harmful effects on the shellfish Organohalogenated The concentration of each The concentration of each substance in substances substance in shellfish flesh must be the shellfish water or in shellfish flesh so limited that it contributes in must not reach or exceed a level which accordance with Article 1 (of the has harmful effects on the shellfish Directive), to the high quality of larvae shellfish products Metals (Ag, As, Cd, The concentration of each The concentration of each substance in Cr, Cu, Hg, Ni, Pb and substance in shellfish flesh must be the shellfish water or in the shellfish Zn) so limited that it contributes in flesh must not exceed a level which (mg/L) accordance with Article 1 (of the gives rise to harmful effects on the Directive), to the high quality of shellfish and their larvae shellfish products The synergic effects of these metals must be taken into consideration Others Guideline Values (G) Mandatory Value (I) Faecal coliforms ≤ 300 per 100 mL in the shellfish No mandatory value set in the (per 100 mL) flesh and intervalvular liquid Directive

8 Substances affecting Concentration lower than liable to the taste of shellfish impair the taste of the shellfish Saxitoxin (produced by No limit given No limit given dinoflagellates)

9 1.3 Designated shellfish areas

Fourteen shellfish areas were originally designated in 1994 under the Quality of Shellfish Waters Regulations (S.I. No. 200 of 1994, revoked by S.I. No. 268 of 2006). A further 49 areas were subsequently designated in 2009 under the European Communities (Quality of Shellfish Waters) (Amendment) Regulations, 2009 (S.I. No. 55 of 2009). All 63 designated sites are illustrated in Figure 1 below.

Note: Map numbers I to XIV refer to waters originally designated under the European Communities (Quality of Shellfish Waters) Regulations 2004 (S.I. No. 200 of 1994), while map numbers 1 to 45 refer to waters designated under the European Communities (Quality of Shellfish Waters) (Amendment) Regulations 2009 (S.I. 55 of 2009). The referenced maps can be found in the relevant regulatory documents.

FIGURE 1 - 63 designated shellfish areas

10 1.4 Development of Shellfish Pollution Reduction Programmes

The Directive and Regulations require that any non-compliances with the shellfish water quality parameter values are identified. The Directive and Regulations further require that the factors responsible for such non-compliances are identified.

Information on impacts and pressures has therefore been collated in an individual characterisation report for each shellfish site from available inventories. The likelihood of the pressures to impact on shellfish water quality parameter values in the shellfish areas has been estimated.

Individual site Pollution Reduction Programmes (PRPs) and a supporting toolkit of measures outline the measures which can be used to control pressures where necessary to protect and improve water quality in a specific shellfish area.

The 2009 Shellfish PRPs (including the supporting characterisation reports and toolkit of measures) represent an initial phase of Shellfish PRP development, drawing on available information sources. Their development has been a desk-based exercise and they provide a good indication of the main pressures likely to be impacting on shellfish water quality and the measures that can be used to control those pressures. Ongoing assessment and monitoring of shellfish waters will be used to confirm the effectiveness of these programmes and to refine the programmes where necessary. As the shellfish monitoring database grows, and as programmes are implemented, incremental changes will be made to ensure compliance with the standards and objectives established.

PRPs produced during 2009 supersede Action Programmes which were developed in 2006 for the 14 original shellfish areas.

1.5 Assessment of Shellfish Pollution Reduction Programmes

A Strategic Environmental Assessment (SEA) of the Shellfish PRPs and supporting toolkit of measures has been carried out in accordance with the requirements of the EU Strategic Environmental Assessment Directive (2001/42/EC). SEA is a process for evaluating, at the earliest appropriate stage, all of the possible environmental effects of plans or programmes before they are adopted while giving the public and other interested parties an opportunity to comment and to be kept informed of decisions and how they were made. The assessment of the PRPs resulted in mitigation of some of the measures contained in the PRPs and toolkit of measures that were identified as likely to lead to adverse effects on other aspects of the environment. The reports associated with the SEA process can be downloaded from www.environ.ie.

An ‘Appropriate Assessment’ of the Shellfish PRPs has been carried out in parallel with the SEA assessment in accordance with the requirements of the EU Habitats Directive (92/43/EEC). Appropriate Assessment is a process for evaluating the implications of plans or programmes for sites which have been designated for the protection and conservation of habitats and species of European importance. The reports associated with the Appropriate Assessment can be downloaded from www.environ.ie.

11 1.6 Links with the River Basin Management Plans

The EU Water Framework Directive (2000/60/EC) provides a framework for the protection and restoration of the aquatic environment and terrestrial ecosystems and wetlands directly depending on the aquatic environment. In accordance with the requirements of the directive, River Basin Management Plans (RBMPs) were published in draft form in December 2008 with the final RBMPs published in December 2009. They are the primary plans in place in relation to the water environment for the foreseeable future.

Article 13(5) of the WFD states that ‘river basin management plans may be supplemented by the production of more detailed programmes and management plans for sub-basin, sector, issue, or water type, to deal with particular aspects of water management’. Shellfish PRPs are an example of such programmes. In addition, Article 13(4) and Annex VII of the WFD requires that RBMPs include ‘a register of any more detailed programmes and management plans for the River Basin District dealing with particular sub-basins, sectors, issues or water types, together with a summary of their contents’. The Shellfish PRPs are included in the registers of each of the River Basin Districts.

Articles 4 (1)(c) and 4 (2) of the WFD specify that, in relation to protected areas, where more than one of set of objectives relate to a given body of water, the most stringent shall apply. Designated shellfish areas are included in the WFD register of protected areas provided for in Articles 6 and 7 of the directive.

The WFD strengthens and consolidates a number of existing environmental directives while repealing others on a phased basis. The Shellfish Directive is due to be repealed by the WFD in 2013. Shellfish PRPs are therefore closely aligned with the RBMPs.

1.7 Layout of the Shellfish Pollution Reduction Programmes

Characterisation Report

• Section 1 Section 1 is an introductory section which puts the Characterisation Reports in context and outlines their contents.

• Section 2 Section 2 describes the general characteristics of the designated shellfish areas as well as their contributing catchments.

• Section 3 Section 3 describes water quality in the designated shellfish areas.

• Section 4 Section 4 consists of a series of maps illustrating the general characteristics of the shellfish areas and catchments, as well as the marine and land-based pressures in the catchments.

12 • Section 5 Section 5 provides a series of tables summarising the marine and land-based pressures in the catchments. The likelihood of the pressures to impact on shellfish water quality parameters is discussed. A summary is also provided highlighting the key pressures and potential secondary pressures which are most likely to be impacting on shellfish water quality parameters. The discussions in this section draw on available information including information generated during the WFD implementation process and geographical features of significance. The differing nature of the pressures are also taken into account as pressures vary substantially in terms of how severely they are likely to impact on shellfish water quality parameters.

Pollution Reduction Programmes

• The Pollution Reduction Programmes summarise the specific measures for controlling the key and potential secondary pressures, identified in this characterisation report, which are most likely to be impacting on shellfish water quality in McSwynes Bay shellfish area. This can be downloaded from www.environ.ie.

Toolkit of Measures

• The supporting toolkit of measures outlines all of the measures available for controlling all of the pressures which can impact on shellfish water quality. Due to the close alignments between the Shellfish PRPs and the RBMPs, the toolkit is drawn from the programme of measures contained within the RBMPs. This strengthens the integration of shellfish management and wider water quality management policy in . The toolkit can be downloaded from www.environ.ie.

13 2.0 GENERAL CHARACTERISTICS

Name McSwynes Bay Shellfish Area Map number 21 Year of designation 2009 Area 2.7 km2 River Basin District North Western IRBD 54 deg 37.037 min North (Lat) Location of sampling point 8 deg 23.080 min West (Long) Catchment area 112.6 km2

McSwynes Bay is situated on the southwest coast of County Donegal in the North Western International River Basin District (Map 1). The bay is exposed to the southwest but is protected to the east by the long arm of St. Johns Point and to the west by Carntullagh Head. The substrate varies from clean sand to rock. Inter-tidal areas are very limited and only at Harbour does much of the sea bed become exposed at low water. A number of shallow rocky reefs are located in the north of the bay, a single tiny island known as the Green Island is also located in the north of the bay.

The designated shellfish area within the bay is 2.7 km2 in area. It covers all of McSwynes Bay within a line south-east from Multins and west from Kiln Port.

The contributing catchment of the shellfish area is almost 112.6 km2 in area (Map 3). One river, the Oily, drains the catchment and enters the bay at Ballyloughan. It is a spatey river of approximately 3 miles in length. Its two tributaries, the Tullinteane and Corker, extend the catchment area.

The main town is with a population of 363. The overall population within the catchment is approximately 24,614. Farming in the region is based principally on sheep rearing and is generally carried out on a small and part time basis.

2.1 Protected areas

The designated shellfish area lies within the McSwynes Bay cSAC (Map 11). Other SACs which intersect the shellfish area’s catchment are the St. John’s Point and Lough Nillian Bog; Lough Nillian Bog is also an SPA. A nutrient sensitive area within the catchment is Killibegs Harbour.

2.2 Shellfish growing activity

Table 2 summarises the number and area of licensed shellfish areas within the designated shellfish area. Mussel cultivation is predominant in the area (Map 2).

14 TABLE 2 - Licensed shellfish areas Shellfish types Number Area % Area Abalone 0 0 0 % Clams 0 0 0 % Cockles 0 0 0 % Lobsters 0 0 0 % Scallops 0 0 0 % Mussels 10 0.4 km2 14.8 % 2 Oysters 2 0.09 km 3.3 % Sea Urchins 0 0 0 % Periwinkles 0 0 0 % Seaweed 0 0 0 %

Other 0 0 0 %

15 3.0 WATER QUALITY IN THE SHELLFISH AREA

Dedicated shellfish monitoring data has been collated and compared with shellfish water quality parameter mandatory and guideline values outlined in Annex I of the Shellfish Waters Directive (2006/113/EC) and Schedule 2 and 4 of the Quality of Shellfish Waters Regulations (S.I. No. 268 of 2006) (Table 1).

Additional monitoring data from other monitoring programmes has also been collated in order to highlight any water quality issues in the vicinity of the shellfish areas. This can aid in the identification of the pressures most likely to impact on the shellfish areas and thereby in the identification of any measures to be applied. Datasets were collated from the Environmental Protection Agency (EPA), the Marine Institute (MI) and the Sea Fisheries Protection Authority (SFPA). Where applicable these additional monitoring data were compared with the shellfish water quality parameter mandatory and guideline values outlined in Annex I of the Shellfish Waters Directive (2006/113/EC) and Schedules 2 and 4 of the Quality of Shellfish Waters Regulations (S.I. No. 268 of 2006) (Table 1).

Marine Institute Shellfish Monitoring Programme

The MI carries out shellfish monitoring at designated shellfish areas. This dedicated shellfish monitoring programme involves analysing for general components, metals and organics in both water and biota samples. The results have been compared with the shellfish mandatory and guideline values outlined in Table 1.

For this designated area there is 1 water sample available from 2005 and 6 biota samples available from between 2004 and 2008. The shellfish mandatory and guideline values outlined in Table 1 were not breached in any of these samples.

Faecal coliform biota results were also available from the MI at all shellfish areas from November 2008, February 2009, May 2009 and August 2009. The shellfish guideline value for faecal coliforms in biota outlined in Table 1 was not breached in any of these samples

EPA Marine Monitoring Programme

The EPA Marine Monitoring Programme analyses for pH and dissolved oxygen in water samples at a large number of marine sites around Ireland. There was 1 sample available from this programme for the designated shellfish area but it was compliant with the shellfish standards for pH and dissolved oxygen.

WFD Monitoring Programme

WFD status classifications from the WFD monitoring programme apply at the water body scale and are generally based on several samples/surveys targeting a variety of parameters including biological, physico-chemical, chemical and hydromorphological elements. The monitoring information on which the marine status classifications are based was collected by the EPA, the MI, the National Parks and Wildlife Service (NPWS) and the Central Fisheries Board (CFB) between 2005 and 2008.

16 The WFD status of the coastal water body, within which the shellfish area is situated, is ‘high’ and therefore satisfactory. The Oily River which discharges into the shellfish area is ‘good’ and therefore satisfactory (Map 12).

Shellfish Flesh Monitoring Programme

Shellfish flesh classifications (carried out under the European Communities (Live Bivalve Molluscs) (Health Conditions for Production and Placing on the Market) Regulations, 1996 (S.I. No. 147 of 1996)) indicate faecal contamination in shellfish flesh. Sampling is carried out by the Sea Fisheries Protection Authority (SFPA) on at least a monthly basis.

The licensed areas within the designated areas for Mussels are classified as Class A meaning that live bivalve molluscs may be collected for direct human consumption and meet the health standards for live bivalve molluscs laid down in the EC Regulation on food safety (Regulation (EC) No 853/2004). However, this is a seasonal classification and it reverts to Class B from the 1st of July to the 30th of November, meaning that shellfish may be placed on the market for human consumption only after treatment in a purification centre or after relaying so as to meet the health standards. However, this shellfish area is in compliance with the shellfish guideline value for faecal coliforms as noted above.

Overall Water Quality

The dedicated shellfish samples available for this shellfish area were found to be compliant with shellfish mandatory and guideline values outlined in Annex I of the Shellfish Waters Directive (2006/113/EC) and Schedule 2 and 4 of the Quality of Shellfish Waters Regulations (S.I. No. 268 of 2006) (Table 1). Ongoing shellfish monitoring will strengthen the assessment of compliance status at this shellfish area.

The results of the WFD monitoring programme does not indicate any water quality issues within the shellfish area or in the waters discharging in the vicinity of this shellfish area.

The shellfish flesh classification monitoring indicates low levels of faecal contamination in this shellfish area but the area is in compliance with the shellfish guideline value for faecal coliforms as indicated above.

17 4.0 CHARACTERISATION MAPS

The following series of maps illustrate the general characteristics of the designated shellfish area and its contributing catchment, as well as the marine and land-based pressures that could potentially impact on the shellfish area. The pressures are further divided into point source pressures, diffuse source pressures and morphological pressures.

Some of the point source pressures are symbolised according to whether they are ‘at risk’ or ‘not at risk’. These risk designations were developed during the WFD implementation process. Some of the designations date back to the Article V characterisation process in 2004 and 2005 but many of the risk designations were updated in 2008 to feed into the draft RBMPs. The risk designations are based on a variety of information, for example, waste water treatment plants can be designated as ‘at risk’ because they are serving a larger population then they were designed to cater for or because their discharges are impacting on water quality. Section 5 of this characterisation report provides the detail behind the risk designations for each of the pressures and discusses their likelihood to be impacting on shellfish water quality parameters.

Whilst the risk designations under the WFD provide a useful screening tool for pressures, their relevance in terms of any water quality issues measured in Shellfish Waters has been assessed in further detail to identify key pressures at a particular site. For example the WFD risk may be based on particular impacts to freshwater ecology which are not pertinent to the shellfish water status.

TABLE 3 - List of maps Map No. Map Title Details General Characteristics Maps MAP 1 Designated shellfish area Designated shellfish area with summary statistics. MAP 2 Licensed shellfish areas Department of Agriculture, Fisheries and Food register of licensed shellfish areas within the designated shellfish area. MAP 3 Contributing catchment Nested river water bodies and inter-coastal freshwater bodies discharging in the vicinity of the designated shellfish area. MAP 4 Topography Topography of the contributing catchment. MAP 5 Soil wetness Soil wetness which indicates drainage characteristics MAP 6 Vulnerability of Potential risk of pathogens from sub-soils groundwaters to discharges reaching groundwaters. Based on pathogens from subsoil vulnerability, presence of alluvium, mineral discharges content of soils, wetness, aquifer type, subsoil depth and subsoil permeability.

18 Map No. Map Title Details MAP 7 Vulnerability of Potential risk of phosphorus from sub-soils groundwaters to discharges reaching groundwaters. Based on phosphorus from subsoil vulnerability, presence of alluvium, mineral discharges content of soils, wetness, aquifer type, subsoil depth and subsoil permeability. MAP 8 Vulnerability of surface Potential risk of pathogens from sub-soils waters to pathogens discharges reaching surface waters. Based from subsoil discharges on vulnerability, presence of alluvium, mineral content of soils, wetness, aquifer type, subsoil depth and subsoil permeability. MAP 9 Vulnerability of surface Potential risk of phosphorus from sub-soils waters to phosphorus discharges reaching surface waters. Based from subsoil discharges on vulnerability, presence of alluvium, mineral content of soils, wetness, aquifer type, subsoil depth and subsoil permeability. MAP 10 Likelihood of inadequate Likelihood of inadequate percolation in percolation in subsoils subsoils. Based on aquifer type, vulnerability and subsoil permeability. MAP 11 Designated protected SACs, SPAs, freshwater pearl mussel areas, areas recreational waters, drinking waters, nutrient sensitive areas, water dependant habitats and RAMSAR sites within the contributing catchment. MAP 12 WFD surface water River, lake, transitional and coastal water status body status resulting from the WFD monitoring programme. MAP 13 EPA diffuse risk Water body based risk to waters from diffuse assessment sources. Based on the percentages of diffuse land cover per water body including peatlands, coniferous forestry, agriculture and urban areas. Marine Pressures Maps Point Source Pressures MAP 14 Marine finfish farms Marine finfish farms in the vicinity of the designated shellfish area. Taken from the Marine Atlas. Morphology Pressures MAP 15 Fishing gear activity Fishing gear activity in the vicinity of the designated shellfish area. Taken from the Marine Atlas. MAP 16 Structures Marine morphology structures such as bridges and causeways

19 Map No. Map Title Details MAP 17 Physical modifications Physical modifications such as shoreline reinforcement, embankments, reclaimed land, capital and maintenance dredging, aggregate removal, dumping at sea and heavily modified waters within the designated shellfish area. Land-based Pressures Maps Point Source Pressures MAP 18 Municipal waste water Urban waste water treatment plants and systems combined sewer overflows within the contributing catchment. These are symbolized based on their risk designations. MAP 19 Agricultural and Pig units, and freshwater fish farms within aquacultural point the contributing catchment. source pressures MAP 20 Industrial point source Industrial IPPCs, Section 4s, water treatment pressures plants, abstractions, mines, quarries, landfills and contaminated sites within the contributing catchment. These are symbolized based on their risk designations. Diffuse Source Pressures MAP 21 On-site waste water On-site waste water treatment plants within systems the contributing catchment. MAP 22 Dairy and drystock Dairy and drystock livestock units per livestock units hectare of farmed land within each DED in the contributing catchment. MAP 23 Nitrogen fertiliser usage Nitrogen fertiliser usage per hectare of farmed land within each DED in the contributing catchment. MAP 24 Phosphorus fertiliser Phosphorus fertiliser usage per hectare of usage farmed land within each DED in the contributing catchment. MAP 25 Forestry types with Forest cover in the contributing catchment acidification risk areas with areas identified as being at risk from acidification. MAP 26 Forestry types with Forest cover in the contributing catchment eutrophication risk areas with areas identified as being at risk from eutrophication. MAP 27 Forestry types with Forest cover in the contributing catchment sedimentation risk areas with areas identified as being at risk from sedimentation. Morphology Pressures

20 Map No. Map Title Details MAP 28 Structures Barriers to migration, both natural and man- made in the contributing catchment. MAP 29 Physical modifications Channelisation, heavily modified and artificial water bodies in the contributing catchment.

21 MAP 1 - Designated shellfish area

22 MAP 2 - Licensed shellfish areas

23 MAP 3 - Contributing catchment

24 MAP 4 – Topography

25 MAP 5 - Soil wetness

26 MAP 6 - Vulnerability of groundwater to pathogens from subsoil discharges

27 MAP 7 - Vulnerability of groundwater to phosphorus from subsoil discharges

28 MAP 8 - Vulnerability of surface waters to pathogens from subsoil discharges

29 MAP 9 - Vulnerability of surface waters to phosphorus from subsoil discharges

30 MAP 10 - Likelihood of inadequate percolation in sub-soils

31 MAP 11 - Designated protected areas

32 MAP 12 - WFD surface water status

33 MAP 13 - Diffuse risk assessment

34 MAP 14 - Licensed finfish areas

35 MAP 15 - Fishing gear activity

36 MAP 16 - Marine structures

37 MAP 17 - Marine physical modifications

38 MAP 18 - Municipal waste water systems (None in this catchment)

39 MAP 19 - Pig units and finfish farms (None in this catchment)

40 MAP 20 - Industrial point source pressures

41 MAP 21 - On-site waste water systems

42 MAP 22 - Dairy and drystock livestock units

43 MAP 23 - Nitrogen fertiliser usage

44 MAP 24 - Phosphorus fertiliser usage

45 MAP 25 - Forestry types with acidification risk areas

46 MAP 26 - Forestry types with eutrophication risk areas

47 MAP 27 - Forestry types with sedimentation risk areas

48 MAP 28 - Freshwater structures

49 MAP 29 - Freshwater physical modifications (None in this catchment)

50 5.0 PRESSURES

This section of the characterisation report provides a tabular overview and inventory of the marine and land-based pressures in the vicinity of the designated shellfish area and within the contributing catchment up to a distance of 20 kilometres from the shellfish area. The pressure data has been derived from existing inventories. The pressures considered most likely to be related to any measured impacts on shellfish water quality parameters in this shellfish area have been estimated in order to focus management efforts towards the protection and improvement of the water quality in this shellfish area.

The available information considered when determining the likelihood of the pressures to cause impacts includes:

• pressure type

The pressure types, be it marine or land-based, point, diffuse or morphological, vary in terms of: their likelihood to impact on shellfish water quality; the water quality parameters they are likely to affect; and the severity of the impacts. The results of monitoring can therefore provide an indication of which pressure types are likely to be causing impacts.

• pressure magnitude

The magnitude of the pressures acting on a shellfish area can affect the overall potential impact. For marine pressures, the magnitude depends on the number and scale of the pressures but also on the exposure of the shellfish area to the pressures which in turn depends on how open or sheltered the shellfish area is and on water circulation. For land-based pressures, the magnitude depends on the number and scale of the pressures but also on the remoteness of the pressures from the shellfish areas which in turn depends on the distance of the pressures from the shellfish area, the topography of the catchment and the presence of lakes downstream of pressures which can act as pollution sinks.

• WFD risk designations

A series of risk assessments relating to the main pressures on waters were carried out during the WFD implementation process to identify pressures ‘at risk’ of impacting the surrounding water environment. These were originally carried out in 2004 and 2005 in accordance with Article V of the directive but many of them were subsequently updated in 2008 to feed into draft River Basin Management Plans. A lot of information about the pressures was collected to undertake these assessments and some of that information is summarised in this section where it is useful in screening which pressures are most likely to impact on shellfish water quality. In all cases, the most up-to-date risk assessment information available was used. Full details of the WFD risk assessments can be found at www.wfdireland.ie.

Whilst the risk designations under the WFD provide a useful screening tool for pressures, their relevance in terms of any water quality issues measured in Shellfish Waters has to be assessed in further detail to identify key pressures at a particular site.

51 Table 4 lists all of the pressures considered in the development of the characterisation report and indicates their presence or absence within the shellfish area, within the marine waters in the vicinity of the shellfish area or within the contributing catchment. Those pressures that are present are discussed later in this section.

TABLE 4 - Summary of pressures Pressure Pressure Pressures Present type Marine Point Marine finfish farms Yes Morphology Fishing gear activity Yes Structures and associated activities Ports Yes Flow/Sediment manipulation structures Yes Piled structures Yes Causeways No Physical modifications Shoreline reinforcement No Embankments No Reclaimed Land No Capital dredging No Maintenance dredging Yes Aggregate removal No Disposal at sea No Marine heavily modified waters Yes Land-based Point Urban wastewater systems Urban waste water treatment systems No Combined sewer overflows No Agricultural and aquacultural point sources Pig units No Freshwater finfish farms No Industrial point sources Abstractions Yes Water treatment plants Yes IPPCs Yes Section 4s Yes Quarries No Landfills Yes Mines No Contaminated lands No Other No Diffuse On-site waste water treatment systems Yes Agriculture Livestock density Yes Nitrogen fertiliser usage Yes Phosphorus fertiliser usage Yes Forestry Yes Morphology Structures Barriers to migration Yes Physical Modifications Channelisation No Heavily modified waters No Artificial waters No

52 5.1 Marine Pressures

Marine pressures are considered up to a distance of 5 kilometres from the shellfish area. Marine pressures situated further away or in adjacent waterbodies are also mentioned if they are considered significant. Marine pressure types include point source pressures (marine finfish farms) and morphological pressures including fishing gear activity, structures (ports, bridges, piers, slipways etc) and physical modifications (shoreline reinforcement, embankments, dredging etc). The potential impacts associated with these pressures are as follows:

• Point source pressures

Marine finfish farms can be associated with increased nutrient levels in waters, arising from fish excretion and excess feed input.

• Morphological pressures

Fishing activity can be associated with increased suspended sediment levels arising from disturbance of the seabed. The potential severity of the impacts varies depending on the type of fishing gear used and the extent, frequency and duration of the activity. The impact of boats is dealt with in association with marine structures below.

Structures (such as ports, harbours, bridges, slipways and piers) alter natural processes such as flow and silt movement and can therefore affect levels of suspended sediment in marine waters. The activities associated with these structures, for example shipping and boating, are associated with effects on the levels of general physico-chemical parameters, faecal coliforms, metals and chemicals.

Physical modifications (such as shoreline reinforcement, embankments and dredging) can alter natural processes such as flow and silt movement and can therefore affect levels of suspended sediment. However, once these modifications are established or the activities have ceased, the surrounding environment can acclimatise and impacts do not necessarily continue.

The following tables summarise the nature and extent of marine pressures up to a distance of 5 kilometres from the designated shellfish area. The likelihood for these pressures to impact on shellfish water quality parameters is discussed. The potential severity of the impacts of marine pressures is most closely associated with the activity type, magnitude and proximity and therefore the discussions in this section focus on these factors.

53 5.1.1 Point source pressures

Marine finfish farms

TABLE 5 - Finfish farms Fishing gear types Direct 0-5 km Comment Salmonid fish farms 0 16 NA Other finfish farms 0 0 NA

Table 5 provides a summary of the marine finfish farms located within 5 kilometres of the designated shellfish area. Map 14 illustrates these pressures. Marine finfish farms can be associated with elevated nutrient levels from fish excretion and excess feed input.

There are 16 marine finfish farms within 5 kilometres of the shellfish area. Monitoring in the shellfish area does not indicate any water quality issues which are likely to be associated with these finfish farms and the WFD status of the marine water body within which they are located is ‘high’. Therefore, these finfish farms are unlikely to be affecting shellfish water quality in this shellfish area.

5.1.2 Morphology pressures

An assessment of the risk posed to marine waters from marine morphology pressures was carried out during the WFD implementation process. The results of this assessment show that the marine waters in and around this shellfish area are considered to be ‘not at risk’ from morphological pressures.

Fishing gear activity

TABLE 6 - Fishing gears Fishing gear types Type Present Comment Pots Static Yes Large are to the west of the shellfish area Tangle Nets Static No NA Bottom Set Gill Nets Static Yes Large area to the southwest of the shellfish area Draft Nets Static No NA Drift Nets Static Yes Widespread throughout the area Line Fishing Static Yes Widespread throughout the area Box Dredge Mobile No NA Cockle Dredge Mobile No NA Hydraulic Dredge Mobile No NA Scallop Dredge Mobile No NA Oyster Dredge Mobile No NA Otter Trawl Mobile No NA Beam Trawl Mobile No NA Digging NA No NA Gathering NA Yes Widespread throughout the area Rake NA No NA

54 Table 6 provides a summary of the fishing gear activity occurring within 5 kilometres of the designated shellfish area. Map 15 illustrates these pressures. Boat movements are dealt with below in association with marine structures such as ports and piers.

Static fishing gear types generally would not be expected to impact on shellfish water quality. Mobile fishing gears however disturb the seabed and can therefore affect the levels of suspended sediments in marine waters with the severity of the impacts depending on the frequency, intensity and extent of the fishing activity.

Static fishing gear activity in the area includes widespread line fishing (lines set on the seabed with bated hooks at intervals); the use of pots (bated traps set on the seabed targeting crustaceans); the use of bottom set gill nets (curtain of netting which allow fish to swim partway through the mesh to become caught with the gills preventing backward movement) and the use of drift nets (curtains of netting hanging from the surface). These static fishing gear types are unlikely to affect shellfish water quality in this shellfish area.

Structures and associated activities

TABLE 7 - Marine morphology structures Marine morphology structures Direct 0-5km Comment Ports 0 1 commercial and fishing port Flow and sediment manipulation 3 16 Piers, slipways, jetties, quays Piled structures 0 3 Jetties, road bridge Causeways 0 0 NA

Table 7 provides a summary of the marine morphology structures located within 5 kilometres of the designated shellfish area. Map 16 illustrates these pressures. Flow and sediment manipulation structures include piers, breakwaters, groynes, flow deflectors and training walls. Piled structures include bridge and pier supports and wind turbines. Causeways include roads and railway lines. These structures affect flow and sediment movement and can therefore impact on levels of suspended sediments, though these impacts can settle down once the structures are well established in an area. The activities associated with marine structures, including shipping and boating, can affect a wide range of water quality parameters including general physico-chemical parameters such as suspended sediment, dissolved oxygen and nutrient levels. Faecal coliform levels can also be affected as well as the levels of harmful substances such as metals and pesticides. Boat movements can lead to erosion and sedimentation effects as well as pollution from fuels.

Killybegs commercial and fishing port is situated less then 5 kilometres to the northwest of the shellfish area. There is also 3 pier structure directly adjacent to the shellfish area as well as 16 additional pier structures and 3 piled structures within 5 kilometres of the shellfish area.

Killybegs harbour is a deep fjord-like inlet and is one of the safest, most sheltered, deep-water harbours on the Irish coast. The port is designed to cater for vessels up to 300 metres in length, 40,000 tonnes dead weight and with a maximum draft of 12

55 metres at low water. On shore, experienced service providers offer the complete package of agency, stevedoring and other ancillary services.

Monitoring does not indicate any water quality issues which are likely to be associated with these structures or their associated activities, the WFD status of the water bodies within which the activity is taking place is ‘high’ and the WFD assessment of the risk posed to marine waters from marine morphology pressures deems the marine waters in and around this shellfish area to be ‘not at risk’. Therefore, it is unlikely that the structures themselves or their associated activities are affecting shellfish water quality in this shellfish area.

Physical modifications

TABLE 8 - Physical modifications Physical modifications Direct 0-5 km Comment Shoreline reinforcement 0 0 NA Embankments 0 0 NA Reclaimed land 0 0 NA Capital dredging 0 0 NA Maintenance dredging 0 3 Shipping channels Aggregate removal 0 0 NA Dumping at sea 0 0 NA

Table 8 provides a summary of the physical modifications occurring within 5 kilometres of the designated shellfish area. Map 17 illustrates these pressures. These modifications can affect flow and sediment movement though these impacts can cease once the modifications are established.

There are no physical modifications in the direct vicinity of this shellfish area but there are 3 areas of maintenance dredging within 5 kilometres of the shellfish area. Monitoring in the area does not highlight any water quality issues which are likely to result from these modifications, the WFD status of the water bodies in the area is ‘high’ and the WFD assessment has deemed the area to be ‘not at risk’ from morphological pressures. Therefore, these modifications are unlikely to be affecting shellfish water quality in this shellfish area.

TABLE 9 - Heavily modified waters HMWB name Distance Extent Comment Killybegs Harbour 0-5 3 km2 NA

Table 9 lists the heavily modified marine waters located within 5 kilometres of the designated shellfish area. Map 17 illustrates these pressures. Such modifications can affect flow and sediment movements though these impacts can cease once the modifications are established.

Killybegs harbour has been heavily modified and is situated to the north west of the shellfish area. Monitoring in the area does not highlight any water quality issues which are likely to be associated with this modified water, the WFD status of the water bodies in the area is ‘high’ and the WFD assessment has deemed the area to be

56 ‘not at risk’ from morphological pressures. Therefore, this modification is unlikely to be affecting shellfish water quality in this shellfish area.

57 5.2 Land-based Pressures

The contributing catchment is used to identify the land-based pressures that could potentially be impacting on shellfish water quality and therefore the size of the contributing catchment can be important in determining the magnitude of the pressures. Contributing catchment sizes vary considerably; however, pressures are only considered up to a distance of 20 kilometres from the shellfish area and are, where appropriate, divided into four zones: direct, 0 to 5 kilometres, 5 to 10 kilometres and 10 to 20 kilometres. Pressures within the catchment, but further than 20 kilometres from the shellfish area, are also included if they are considered significant. In addition significant land-based pressures acting in adjacent waterbodies which may have an impact due to tidal influences are also considered where relevant.

Land-based pressure types include point source pressures, diffuse source pressures and morphology pressures. The shellfish water quality parameters potentially impacted by these pressures are as follows:

• Point source pressures can affect the whole suite of shellfish water quality parameters. For example, waste water treatment plants, CSOs and agricultural point sources can impact on the levels of faecal coliforms, nutrients, bacteria and other harmful substances in receiving waters while IPPC licensed industries, mines, quarries and landfills can impact on the levels of polluting substances in receiving waters such as petroleum hydrocarbons, organohalogenated substances and metals. Abstractions are included under this heading and can impact on salinity levels, though not to an extent likely to lead to non-compliances with shellfish water salinity standards, as well as reducing the dilution available for polluting discharges.

• Diffuse source pressures affect many of the shellfish water quality parameters. Agricultural activity and on-site waste water treatment systems (OSWTS) can impact on faecal coliform levels as well as general physico-chemical parameters such as the levels of suspended sediments and dissolved oxygen. Forestry activity can impact on the pH of receiving waters as well as on the levels of suspended solids and nutrients and it is also associated with the use of pesticides which can contain organohalogenated substances.

• Land-based morphology pressures, and associated activities, are not generally associated with impacts on water quality in marine areas. Their impacts are usually associated with the loss of natural freshwater features and habitats and changes to the behaviour of freshwater systems including sediment movement. Channelisation activities however, if occurring close to shellfish areas, can impact on shellfish water quality, particularly the levels of suspended sediment.

The following tables summarise the nature and extent of land based pressures within the catchment up to a distance of 20 kilometres from the designated shellfish area. The likelihood for these pressures to impact on shellfish water quality parameters is discussed. All of the factors discussed at the beginning of this chapter can affect the likelihood for land-based pressures to impact on shellfish waters.

58 5.2.1 Point Source Pressures

Abstractions

TABLE 10 – Abstractions Name Map Type Distance Status Abs Rate At Risk Ref m3 day-1 (Ratio) Lough Adeery 45 Lake 5-10 Good 3,070 Yes (> 40%) Lough Aroshin 48 Lake 5-10 Good 3,070 Yes (> 40%) Meentinadae 74 River 10-20 Moderate 55 No Stream

Table 10 lists the abstractions in the catchment up to a distance of 20 kilometres from the designated shellfish area. Map 20 illustrates these pressures and map references link the map and table. Information provided in the table in relation to abstractions includes:

• the type of abstraction (river, lake or groundwater) • the distance of the abstraction from the designated shellfish area • the WFD status of the water body within which the abstraction is located • the abstraction rate, expressed in cubic metres per day • the WFD risk designations associated with the abstractions and the reasons behind the designations

The WFD risk assessment in relation to abstractions was updated in 2008 to feed into the draft RBMPs. Abstractions are deemed to be ‘at risk’ if they account for a significant proportion (>10%) of the resource. For river abstractions, the net abstraction is expressed as a proportion of the Q95 flow (i.e. the flow that is exceeded 95% of the time). For lake abstractions, the net abstraction is expressed as a proportion of the Q50 inflow to the lake (i.e. the long term median inflow). For groundwater abstractions, the net abstraction is expressed as a proportion of recharge volume (i.e. long term average recharge across the groundwater bodies).

Generally it is very unlikely that abstractions would lead to non-compliances with the shellfish standards for salinity in shellfish areas. Abstractions that represent a large proportion of their corresponding resources can decrease available dilution capacity but this is also unlikely to affect shellfish areas.

There are 3 abstractions in the catchment, 2 of which are ‘at risk’ due to the high ratio of the abstractions to lake inflow. However, as these abstractions are located in water bodies whose WFD status is ‘good’, it is unlikely that they are affecting their surrounding water environment and, consequently, shellfish water quality in the downstream shellfish area.

Water Treatment Plants

TABLE 11 - Water treatment plants Name Map Ref Distance Status Risk Risk

59 Name Map Ref Distance Status Risk Risk Lough Aroshin 312 5-10 Good No expert judgement Meentinadae Stream 340 10-20 Moderate Yes expert judgement

Table 11 lists the water treatment plants in the catchment up to a distance of 20 kilometres from the designated shellfish area. Map 20 illustrates these pressures and map references link the map and table. Information provided in the table in relation to the water treatment plants includes:

• the distance of the plants from the designated shellfish area • the WFD status of the water bodies within which the plants are located • the WFD risk designations associated with the plants and the reasoning behind the designations

The WFD risk assessment for water treatment plants dates back to the Article V characterisation process which was undertaken in 2004 and 2005. At that time expert opinion within the Local Authorities was used to indicate whether plants were ‘at risk’ of impacting on their surrounding water environment.

Discharges from Water Treatment Plants (WTPs) can affect the levels of suspended solids, algae and pathogens in receiving waters. Aluminium can also be present from the treatment process.

There are 2 water treatment plants in the catchment and 1 of them been designated as ‘at risk’ of impacting its surrounding water environment. Monitoring does not indicate any water quality issues which are likely to be associated with this plant and therefore it is unlikely to be affecting shellfish water quality in this shellfish area.

Integrated Pollution Prevention and Control Industries

TABLE 12 - Integrated Pollution Prevention Control Licenses Name Map Ref Distance Status Risk United Fish Industries Ltd 59 0-5 nd Not at risk NOTE: nd denotes ‘no data’ where an industry is located in a water body with no WFD status information

Table 12 lists the IPPC licensed industries in the catchment up to a distance of 20 kilometres from the designated shellfish area. Map 20 illustrates these pressures and map references link the map and table. Information provided in the table in relation to the licensed industries includes:

• the distance of the industries from the designated shellfish area • the WFD status of the water bodies within which the industries are located • the WFD risk designations associated with the industries and the reasoning behind the designations

The WFD risk assessment in relation to IPPC licensed industries was updated in 2008 to feed into the draft RBMPs with a further update currently underway (due for completion by November 2009). The industries were designated as ‘at risk’ for a variety of reasons including:

60 • C Insufficient assimilative capacity for BOD – existing load • D Insufficient assimilative capacity for BOD – future load • E Insufficient assimilative capacity for nutrients – existing load • F Insufficient assimilative capacity for nutrients – future load • G Historical deterioration in downstream Q value where the Q station is within 3 kilometres of the outfall • H Downstream Q value is less than 4 where the Q station is within 3 kilometres of the outfall • I Deterioration in upstream to downstream Q value were the distance between Q stations is less then 3 kilometres • J Exceedance of bathing water quality within 1 kilometre of the outfall • K Exceedance of shellfish water quality within 1 kilometre of the outfall • L Expert opinion

Discharges from IPPC licensed industries are diverse and can affect the levels of faecal coliforms, nutrients, suspended sediments, dissolved oxygen as well as a wide range of chemicals in receiving waters.

There is 1 IPPC licensed industry within the catchment and it has been designated as ‘not at risk’. Also, monitoring does not indicate any water quality issues likely to be associated with this industry. Therefore, it is unlikely to be affecting shellfish water quality in this shellfish area.

Section 4 Licensed Industries

TABLE 13 - Section 4 Licenses Name Map Distance Status Risk Ref Andersons Mink Farm Ltd 160 0-5 km Good Yes – G/H Greencastle Seafoods Ltd 177 5-10 km Moderate No – H/I

Table 13 lists the Section 4 licensed industries in the catchment up to a distance of 20 kilometres from the designated shellfish area. Map 20 illustrates these pressures and map references link the map and table. Information provided in the table in relation to the industries includes:

• the distance of the industries from the designated shellfish area • the WFD status of the water bodies within which the industries are located • the WFD risk designations associated with the industries and the reasoning behind the designations

The WFD risk assessment in relation to Section 4 licensed industries was updated in 2008 to feed into the draft RBMPs with a further update currently underway (due for completion by November 2009). The industries were designated as ‘at risk’ for a variety of reasons which are outlined above.

Discharges from Section 4 licensed industries are diverse and can affect the levels of faecal coliforms, nutrients, suspended sediments, dissolved oxygen as well as a wide range of chemicals in receiving waters.

61 There are 2 Section 4 licensed industries in the catchment and both have been designated as ‘at risk’ due to downstream deterioration in water quality. However, monitoring does not indicate any water quality issues in the shellfish area which are likely to be associated with these industries and therefore they are unlikely to be affecting shellfish water quality in this shellfish area.

Quarries, mines, landfills and contaminated lands

TABLE 14 - Quarries, mines, landfills and contaminated lands Name Map Distance Status Risk Notes Ref Balbane Landfill 92 5-10 Good Yes Lined landfill

Table 14 lists the quarries, mines, landfills and contaminated lands in the catchment up to a distance of 20 kilometres from the designated shellfish area. Map 20 illustrates these pressures and map references link the map and table. Information provided in the table in relation to the plants includes:

• the distance of the industries from the designated shellfish area • the WFD status of the water bodies within which the plants are located • the WFD risk designations associated with the industries

Some of the WFD risk assessments in relation to these point sources were updated in 2008 to feed into the draft RBMPs but some of the assessments date back to the WFD characterisation process in 2004 and 2005. Expert opinion within Local Authorities was used to assign risk designations to quarries and landfills but monitoring data was used for mines and contaminated lands.

Mining and quarrying operations can impact on levels of suspended solids and metals in receiving waters whilst landfills and contaminated sites can be more diverse and impact on the levels of nutrients, suspended sediments and oxygen levels as well as metals and other chemicals.

There is 1 landfill within the catchment and, though it has been designated as ‘at risk’, it is situated in a water body whose WFD status is ‘good’ and monitoring in the shellfish area does not indicate any water quality issues which are likely to be associated with it. Therefore, it is unlikely to be affecting shellfish water quality in this shellfish area.

62 5.2.2 Diffuse Source Pressures

On-site waste water treatment systems

TABLE 15 - On-site waste water treatment systems Risk Number % of total Total number 992 - Number per km2 in the catchment 8.8 - Number per km2 nationally 1.4 - Number that are high risk to surface waters from pathogens 813 81.95% Number that are high risk to groundwaters from pathogens 919 92.64% Number that are high risk to surface waters from phosphorus 961 96.87% Number that are high risk to groundwaters from phosphorus 940 94.76% High likelihood of inadequate percolation of leachate 697 70.26%

Table 15 summarises the numbers of on-site waste water treatment systems (OSWWTS) within the catchment up to a distance of 20 kilometres from the designated shellfish area and outlines how many of them are located in areas of high risk to surface and groundwaters from pathogens and phosphorus and how many of them are located in areas where the likelihood of inadequate percolation of leachate is high. Map 21 illustrates the locations of the OSWWTSs while Maps 6 to 10 illustrate the risk to surface and groundwaters and the likelihood of inadequate percolation, all of which is based on soil, sub-soil and geological characteristics. Generally, systems located in areas where effluent cannot get away underground pose a risk to surface waters while systems located in areas where the effluent moves too quickly through the subsoil pose a risk to groundwaters. OSWWTS effluent can impact on the levels of faecal coliforms, suspended sediments, nutrients and dissolved oxygen in receiving waters. In addition, the use of household cleaning products can introduce a range of harmful chemicals to the water environment.

There are 992 systems in the contributing catchment and their density is much higher than the national average. The risk to surface and groundwaters from pathogens and phosphorus is also high throughout the catchment as is the likelihood of inadequate percolation. The majority of the systems are therefore located in hydrologically unsuitable conditions. Many are located in the coastal region of the catchment in the direct vicinity of the shellfish area. Other factors which affect the likelihood of these systems to impact surface and groundwaters are whether suitable types of systems are selected, whether they are installed correctly, whether they are properly maintained and whether they are situated close to ditches, drains, watercourses, wells or boreholes. Monitoring does not indicate any water quality issues in this shellfish area and therefore these systems are unlikely to be affecting shellfish water quality in this shellfish area.

Agriculture

TABLE 16 - Livestock units and chemical fertiliser usage Indicator Catchment National Average (per ha of farmed land) (per ha of farmed land)

Livestock units 0.29 LU 1.20 LU Nitrogen fertiliser usage 39.61 kg 92.09 kg Phosphorus fertiliser usage 3.79 kg 9.74

63 Nitrates Directive limit = 170 kg N per hectare = approx. 2 LU per hectare Nitrates Directive derogation = 250 kg N per hectare = approx. 3 LU per hectare.

Table 16 provides an estimate of the average number of dairy and drystock livestock units and the average loadings of nitrogen and phosphorus chemical fertiliser per hectare of farmed land within the contributing catchment area. Maps 22, 23 and 24 illustrate this. The figures beneath the table express the nitrate limit (and Ireland’s derogation) under the Nitrates Directive in terms of livestock densities. Discharges related to agriculture can affect the levels of faecal coliforms, suspended sediments, nutrients and dissolved oxygen in receiving waters. In addition, the use of pesticides and herbicides can introduce a range of harmful chemicals to the water environment.

Approximately 50% of the area of this catchment is farmed land. However, estimates of livestock density and fertiliser usage are lower than the national averages. The EPA’s diffuse model risk assessment, which investigates the relationship between catchment attributes (percentages of diffuse land cover including agriculture), water chemistry and ecological status, does not highlight any diffuse risk areas in the catchment (Map 13). However, the prevalence of wet soil types in the catchment (Map 5) and high slopes (Map 4) means there is a risk of agricultural runoff. Monitoring does not indicate any water quality issues in this shellfish area and therefore agriculture is unlikely to be affecting shellfish water quality in this shellfish area.

Forestry

TABLE 17 - Forestry types Type Area Percentage of area Conifers 16.5 km2 14.7 % Broadleaves 1.22 km2 1.1 % Mixed 0.17 km2 0.2 % Other 0 km2 0 % Cleared 3.23 km2 2.9 % Unknown 0.59 km2 0.5 % Total 21.7 km2 19.3 % Nationally 6,795 km2 10.0 %

Table 17 presents the area and percentage area of the catchment under the various types of forest cover. Maps 25, 26 and 27 illustrate this. Forestry activity can impact on the pH of receiving waters as well as on the levels of suspended solids and nutrients. It is also associated with the use of pesticides which can introduce harmful chemicals to the water environment.

This is nearly 22 km2 of forested land in this catchment and the percentage area under forest cover is higher than the national average. Unlike agriculture, the location of forestry activity is known and forestry activity occurs in close proximity to the shellfish area. The EPA’s diffuse model risk assessment, which investigates the relationship between catchment attributes (percentages of diffuse land cover including forestry), water chemistry and ecological status, does not highlight any diffuse risk areas in the catchment (Map 13). Also, the more recent risk assessment, undertaken by the WFD Forest and Water study, does not highlight any risk areas. Monitoring in the shellfish area does not indicate any water quality issues which are likely to be

64 associated with forestry and therefore, it is unlikely to be affecting shellfish water quality in this shellfish area.

65 5.2.3 Morphology Pressures

Structures

TABLE 18 - Natural and man-made barriers Freshwater morphology structures Number Dist Comment Barriers to migration 1 5-10 km Artificial

Table 18 summarises the occurrences of morphological structures within the contributing catchment area up to a distance of 20 kilometres from the designated shellfish area. Map 28 illustrates this. Any impacts associated with barriers, which could include impacts on flow, sediment movement and fish migration, are likely to be localised.

There is 1 artificial barrier to fish migration within the catchment but, because it does not occur in the vicinity of the shellfish area, it is unlikely to be affecting shellfish water quality in this shellfish area.

66 5.3 Summary of Key Pressures

Information from existing data sources has been used to identify all of the pressures acting on the shellfish area and to assess their likelihood to be affecting shellfish water quality in this shellfish area.

Monitoring within and in the vicinity of this shellfish area does not indicate any water quality issues.

This summary section highlights:

• key pressures

The key pressures are those identified as most likely to be affecting shellfish water quality. The final PRP will confirm and focus on these key pressures.

• potential secondary pressures

These pressures are identified as possibly affecting shellfish water quality. The final PRP will either confirm them as key pressures or eliminate them from further consideration.

5.3.1 Key Pressures

None of the pressures in this catchment are considered likely to be affecting shellfish water quality.

5.3.2 Potential Secondary Pressures

None of the pressures in this catchment are considered to be possibly affecting shellfish water quality.

67