User's Manual

Remote Control Unit

Power On/Off

It's possible to use a remote controller within 3~5m, 60 degree of angle scope. You can use an extension receiver for a remote controller if it's far away from the system. The receiver in the system will not work when the extension reciever is connected.

Insert battery

1. Pull out the insert part. 2. Insert battery after checking.. 3. Push in the Insert part. "+" Polarity HDS-1151L

Connection(CAT5e/6 Mode)

How to connect devices with splitter (►Input: Blu-ray Player, HD Stream Generator ►Output: PDP, LCD TV)

I

$.Note

CATC cable is recommended for best results. Use both TMDS & DDC cable to use EDID/HDCP Please ask us if you want to use CAT5e/6 cable only not to use ECMD/HDCP Should re-set the settings of Transmitter & Receiver following the length of CAT5e/8 or resolut" on. For setting, please referto "How to set up CATSe/ff1

10 User's Manual

How to set up CAT5e/6 mode

Transmitter setting

1. Press & Select "Input 1" en the front 2. Press "Input 1" button 5 times. Please check if "beep" also sounds 5 times. 3. After pressing "Input 1" 5 times, you can hear 3 times buzzer sound. Entered "Boost setting mode" 4. How to set "Boost"?

• Press Input 1 or Input 2 buttons Inputi: Make it lower & Input 2: Make it higher.

• The setting value covers from 0 to 12 If you can hear 2 times buzzer sounds during pressing Input 1, it means that the setting value is arrived at the lowest level "0". • IfI you can hear 2 times buzzer sounds during pressing Input 2, it means that the setting value is arrived at the highest level "1Z 5. You have to pay attention to TV display during setting Boost Even though you set best setting for Boost mode but the display is not clear, please re-set "Equalizer setting" of Receiver side. 6. If the setting is finished, press "power" button to store the settings. 7. The setting value will be remained after Power Off or On. HDS-1151L

Troubleshooting for NO power

- Check if LED light on the front is turned on. - Make sure the power cord connectors on both ends are firmly attached. Please refer to the webpage, VWWV.M0N0PRICE.COM for more detailed information for the troubleshooting

Terminology explanation

• CAT5/6 : A kind of Un Shielded Twisted-pair UTP Cable. CAT means Category. ► CATS: - Includes four twisted pairs in a single cable jacket. - Typically has three twists per inch of each twisted pair of 24 gauge copper wires within the cables. - The cable standard provides performance of up to 100 MHz.

► CAT5e - Enhanced version of Cat 5 that adds specifications for far end crosstalk.

► CAT6 - More stringent specifications for crosstalk and system noise. - The cable standard provides performance of up to 250 MHz - Suitable for 10BASE-T /10OBASE-TX and 1000BASE-T (Gigabit ).

• DDC : The , digital connection between a display and a graphics adapter that allows the display to communicate its specifications to the adapter. DDC link is carried on three pins data, clock and ground in a 15-pin VGA connector, a DVI connector or an HDMI connector. Meet the requirements specified in the l2C-bus Specification.

• EDID : Extended display identification data. The EDID includes manufacturer name, product type, phosphor or filter type, timings supported by the display, display size, luminance data and (for digital displays only) mapping data.

14 User's Manual

HDCP: High-bandwidth Digital Content Protection. Form of digital copy protection developed by Corporation to prevent copying of and content as it travels across Display Port, Digital Visual Interface (DVI), High-Definition Multimedia Interface (HDMI), Gigabit Video Interface (GVIF), or Unified Display Interface (UDI)connections, even if such copying would be permitted by fair use laws.

• TMDS : Transition Minimized Differential Signaling Technology for transmitting high-speed serial data and is used by the DVI and HDMI video interfaces, as well as other digital communication interfaces.

• EQ: Equalizer. Allows the user to adjust that used to improve Receive Video Signal.

• Booster : Allows the user to adjust that used to improve Transmitter Video Signal. • Tx : Transmitter. Convert input HDMI signal to output CAT5/6 signal.

• Rx : Receiver. Convert input CAT5/6 signal to output HDMI signal.

15