Limit of Detection for Calibration Methods

Total Page:16

File Type:pdf, Size:1020Kb

Limit of Detection for Calibration Methods Limit of detection for calibration methods MARÍA JOSÉ RODRÍGUEZ CUESTA Doctoral Thesis ROVIRA I VIRGILI UNIVERSITY Tarragona 2006 UNIVERSITAT ROVIRA I VIRGILI LIMIT OF DETECTION FOR SECOND-ORDER CALIBRATION METHODS. M. José Rodríguez Cuesta ISBN: 978-84-690-7787-0 / DL: T.1349-2007 UNIVERSITAT ROVIRA I VIRGILI LIMIT OF DETECTION FOR SECOND-ORDER CALIBRATION METHODS. M. José Rodríguez Cuesta ISBN: 978-84-690-7787-0 / DL: T.1349-2007 Limit of detection for second-order calibration methods Doctoral thesis ROVIRA I VIRGILI UNIVERSITY UNIVERSITAT ROVIRA I VIRGILI LIMIT OF DETECTION FOR SECOND-ORDER CALIBRATION METHODS. M. José Rodríguez Cuesta ISBN: 978-84-690-7787-0 / DL: T.1349-2007 UNIVERSITAT ROVIRA I VIRGILI LIMIT OF DETECTION FOR SECOND-ORDER CALIBRATION METHODS. M. José Rodríguez Cuesta ISBN: 978-84-690-7787-0 / DL: T.1349-2007 Rovira i Virgili University Department of Analytical Chemistry and Organic Chemistry Limit of detection for second-order calibration methods Dissertation presented by María José Rodríguez Cuesta to receive the degree Doctor of the Rovira i Virgili University European PhD Tarragona, 2006 Supervisor Dr. Ricard Boqué i Martí UNIVERSITAT ROVIRA I VIRGILI LIMIT OF DETECTION FOR SECOND-ORDER CALIBRATION METHODS. M. José Rodríguez Cuesta ISBN: 978-84-690-7787-0 / DL: T.1349-2007 UNIVERSITAT ROVIRA I VIRGILI LIMIT OF DETECTION FOR SECOND-ORDER CALIBRATION METHODS. M. José Rodríguez Cuesta ISBN: 978-84-690-7787-0 / DL: T.1349-2007 ROVIRA I VIRGILI UNIVERSITY Department of Analytical Chemistry and Organic Chemistry Dr RICARD BOQUÉ I MARTÍ, Associate professor of the Department of Analytical Chemistry and Organic Chemistry at the Rovira i Virgili University CERTIFIES: That the Doctoral Thesis entitled: ”LIMIT OF DETECTION FOR SECOND- ORDER CALIBRATION METHODS”, presented by MARÍA JOSÉ RODRÍGUEZ CUESTA to receive the degree of Doctor of the Rovira i Virgili University, European PhD, has been carried out under my supervision in the Department of Analytical Chemistry and Organic Chemistry at the Rovira i Virgili University, and that all the results presented in this thesis were obtained in experiments conducted by the above-mentioned student. Tarragona, April 2006 Dr Ricard Boqué i Martí UNIVERSITAT ROVIRA I VIRGILI LIMIT OF DETECTION FOR SECOND-ORDER CALIBRATION METHODS. M. José Rodríguez Cuesta ISBN: 978-84-690-7787-0 / DL: T.1349-2007 UNIVERSITAT ROVIRA I VIRGILI LIMIT OF DETECTION FOR SECOND-ORDER CALIBRATION METHODS. M. José Rodríguez Cuesta ISBN: 978-84-690-7787-0 / DL: T.1349-2007 While writing this thesis I was supervised by Dr. Ricard Boqué, and the work was undertaken in the Chemometrics and Qualimetrics research group, headed by Prof. F. Xavier Rius, of the Analytical Chemistry and Organic Chemistry Department at the Rovira i Virgili University in Tarragona, Spain. The work included a four-month research stay in the winter of 2004 in the Spectroscopy and Chemometrics group of the Quality and Technology Department of Food Science at The Royal Veterinary and Agricultural University (KVL) in Copenhagen, Denmark, where I was supervised by Prof. Rasmus Bro. It also included a scientific collaboration with Prof. J. L. Martínez Vidal, Prof. A. Garrido Frenich, Prof. D. Picón Zamora and Prof. M. Martínez Galera of the Department of Hydrogeology and Analytical Chemistry of the University of Almeria Finally, I appreciate the financial support given by the ‘Agència de Gestió d’Ajusts Universitaris i Recerca’ (2000FI-00632) of the Catalan Government. For those who have helped me to grow as a person and as a researcher, and to all those have helped me to follow my path, each one in their different way. I hope that all of you, friends, family and colleagues, feel identified in these lines. UNIVERSITAT ROVIRA I VIRGILI LIMIT OF DETECTION FOR SECOND-ORDER CALIBRATION METHODS. M. José Rodríguez Cuesta ISBN: 978-84-690-7787-0 / DL: T.1349-2007 UNIVERSITAT ROVIRA I VIRGILI LIMIT OF DETECTION FOR SECOND-ORDER CALIBRATION METHODS. M. José Rodríguez Cuesta ISBN: 978-84-690-7787-0 / DL: T.1349-2007 Table contents Chapter 1. DESCRIPTION OF THE THESIS 1.1. Motivation ...................................................................................-3- 1.2. Objectives ....................................................................................-4- 1.3. Structure .....................................................................................-6- 1.4. Notation and list of symbols ......................................................-8- Chapter 2. INTRODUCTION TO CHEMOMETRICS 2.1. Types of data and instruments used in Analytical Chemistry-13- 2.1.1. Historical Background........................................................................-13- 2.1.2. Tensor Terminology...........................................................................-14- 2.1.3. The Concepts of Bilinearity and Trilinearity .......................................-17- 2.1.4. Deviations from Linearity...................................................................-20- 2.2. Calibration methods....................................................................-22- 2.2.1. From Zeroth- to Second-order Calibration.........................................-22- 2.2.2. Resolution and Calibration Methods for Second-Order Data.............-27- 2.2.2.1 Parallel Factor Analysis (PARAFAC)...................................-31- 2.2.2.2 Iterative Target Transformation Factor Analysis (ITTFA).....-35- 2.2.2.3 Multivariate Curve Resolution-Alternating Least Squares (MCR-ALS)..........................................................................-38- 2.2.2.4 Multi-linear Partial Least Squares (N-PLS)..........................-41- 2.2.3. Uniqueness, Indeterminacies and Constraints ..................................-44- 2.3. Validation of Analytical Methods ..............................................-50- 2.3.1. What is Method Validation? ..............................................................-50- 2.3.2. Figures of Merit. International Recommendations .............................-51- UNIVERSITAT ROVIRA I VIRGILI LIMIT OF DETECTION FOR SECOND-ORDER CALIBRATION METHODS. M. José Rodríguez Cuesta ISBN: 978-84-690-7787-0 / DL: T.1349-2007 2.3.3. Analytical Detection ......................................................................... -55- 2.3.3.1 Hypothesis Testing ............................................................ -55- 2.3.3.2 Critical Level and Detection Limit ...................................... -56- 2.3.3.3 Limit of Detection from Linear Calibration Curves............... -58- 2.3.3.4 Limit of Detection in Multivariate Calibration ....................... -61- Chapter 3. ESTIMATION OF THE LOD FOR PARAFAC 3.1. Introduction..................................................................................-69- 3.2. Paper.............................................................................................-73- Determination of Carbendazim, Fuberidazole and Thiabendazole by Three- Dimensional Excitation–Emission Matrix Fluorescence and Parallel Factor Analysis. Analytica Chimica Acta 491: 47-57 (2003) Chapter 4. ESTIMATION OF THE LOD FOR ITTFA 4.1. Introduction..................................................................................-95- 4.2. Paper.............................................................................................-99- Influence of Selectivity and Sensitivity Parameters on Detection in Multivariate Curve Resolution of Chromatographic Second-Order Data. Analytica Chimica Acta 476: 111-122 (2003) Chapter 5. ESTIMATION OF THE LOD FOR MCR-ALS 5.1. Introduction..................................................................................-125- 5.2. Paper.............................................................................................-129- Development and Validation of a Method for Determining Pesticides in Groundwater from Complex Overlapped HPLC Signals and Multivariate Curve Resolution. Chemometrics and Intelligent Laboratory Systems 77(1- 2): 251-260 (2005) UNIVERSITAT ROVIRA I VIRGILI LIMIT OF DETECTION FOR SECOND-ORDER CALIBRATION METHODS. M. José Rodríguez Cuesta ISBN: 978-84-690-7787-0 / DL: T.1349-2007 Chapter 6. ESTIMATION OF THE LOD FOR N-PLS 6.1. Introduction .................................................................................-157- 6.2. Paper.............................................................................................-161- Standard Error of Prediction at Low Content Levels and Limit of Detection Estimation for Multivariate and Multi-linear Regression. (In press) Chapter 7. CONCLUSIONS 7.1. Introduction .................................................................................-193- 7.2. Conclusions ................................................................................-193- APPENDIX References ...........................................................................................-201- Glossary and abbreviations..................................................................-211- List of papers and meeting contributions .............................................-221- UNIVERSITAT ROVIRA I VIRGILI LIMIT OF DETECTION FOR SECOND-ORDER CALIBRATION METHODS. M. José Rodríguez Cuesta ISBN: 978-84-690-7787-0 / DL: T.1349-2007 UNIVERSITAT ROVIRA I VIRGILI LIMIT OF DETECTION FOR SECOND-ORDER CALIBRATION METHODS. M. José Rodríguez Cuesta ISBN: 978-84-690-7787-0 / DL: T.1349-2007 Chapter DESCRIPTION OF THE THESIS - 1 - UNIVERSITAT ROVIRA I VIRGILI LIMIT OF DETECTION FOR SECOND-ORDER CALIBRATION METHODS. M. José Rodríguez Cuesta ISBN:
Recommended publications
  • Sensitive Determination of PAH-DNA Adducts
    View metadata, citation and similar papers at core.ac.uk brought to you by CORE provided by Elsevier - Publisher Connector Matrix Design for Matrix-Assisted Laser Desorption Ionization: Sensitive Determination of PAH-DNA Adducts M. George, J. M. Y. Wellemans, R. L. Cerny, and M. L. Gross* Midwest Center for Mass Spectrometry, Department of Chemistry, University of Nebraska-Lincoln, Lincoln, Nebraska USA K. Li and E. L. Cavalieri Eppley institute for Research in Cancer and Allied Diseases, University of Nebraska Medical Center, 600 South 42nd Street, Omaha, Nebraska USA Two matrices, 4-phenyl-cw-cyanocinnamic acid (ICC) and 4-benzyloxy-cu-cyanocinnamic acid (BCC), were identified for the determination of polycyclic aromatic hydrocarbon @‘AH) adducts of DNA bases by matrix-assisted laser desorption ionization. These matrices were designed based on the concept that the matrix and the analyte should have structural similarities. PCC is a good matrix for the desorption of not only PA&modified DNA bases, but also PAHs themselves and their rnetabolites. Detections can be made at the femtomolar level. (1 Am Sot Mass Spectrum 1994, 5, 1021-1025) he success of matrix-assisted laser desorption quire sensitive detection methods at the low picomole ionization (MALDI) for the sensitive detection of and mid-femtomole level, respectively [6]. T an analyte depends on the nature of the matrix. One method for detection that also gives structural Rational design of a matrix requires understanding of information is fast-atom bombardment (FAB) coupled the mechanism of MALDI. The mechanism is not fully with tandem mass spectrometry [6-81. Unfortunately, understood. Nevertheless, empirical criteria for matrix the combination lacks sensitivity because there is in selection have been suggested 111.
    [Show full text]
  • Validation of Rapid Enzymatic Quantification of Acetic Acid In
    foods Article Validation of Rapid Enzymatic Quantification of Acetic Acid in Vinegar on Automated Spectrophotometric System Irene Dini 1,* , Ritamaria Di Lorenzo 1, Antonello Senatore 2, Daniele Coppola 2 and Sonia Laneri 1 1 Department of Pharmacy, University of Naples Federico II, Via Domenico Montesano 49, 80131 Napoli, Italy; [email protected] (R.D.L.); [email protected] (S.L.) 2 Lcm Laboratory for Product Analysis of Chamber of Commerce, Corso Meridionale, 80143 Napoli, Italy; [email protected] (A.S.); [email protected] (D.C.) * Correspondence: [email protected] Received: 9 May 2020; Accepted: 4 June 2020; Published: 9 June 2020 Abstract: Vinegar is produced from the fermentation of agricultural materials and diluted acetic acid (diluted with water to 4–30% by volume) via sequential ethanol and acetic acid fermentation. The concentration of acetic acid must be measured during vinegar production. A Community method for analyzing acetic acid in vinegar is a non-specific method based on the assumption that the total acid concentration of the vinegar is attributable to the acetic acid. It consists of titration with a strong base in the presence of an indicator. This test is laborious and has a time-consuming character. In this work, a highly specific automated enzymatic method was validated, for the first time, to quantify the acetic acid in the wine vinegar, in terms of linearity, precision, repeatability, and uncertainty measurement. The results were compared to the Community method of analysis. Regression coefficient 1 and the normal distribution of residuals in the ANOVA test confirmed the method’s linearity.
    [Show full text]
  • Standardizing Analytical Methods
    Chapter 5 Standardizing Analytical Methods Chapter Overview 5A Analytical Standards 5B Calibrating the Signal (Stotal) 5C Determining the Sensitivity (kA) 5D Linear Regression and Calibration Curves 5E Compensating for the Reagent Blank (Sreag) 5F Using Excel and R for a Regression Analysis 5G Key Terms 5H Chapter Summary 5I Problems 5J Solutions to Practice Exercises The American Chemical Society’s Committee on Environmental Improvement defines standardization as the process of determining the relationship between the signal and the amount of analyte in a sample.1 In Chapter 3 we defined this relationship as SktotalA=+nSA reagtor Skotal = AAC where Stotal is the signal, nA is the moles of analyte, CA is the analyte’s concentration, kA is the method’s sensitivity for the analyte, and Sreag is the contribution to Stotal from sources other than the sample. To standardize a method we must determine values for kA and Sreag. Strategies for accomplishing this are the subject of this chapter. 1 ACS Committee on Environmental Improvement “Guidelines for Data Acquisition and Data Quality Evaluation in Environmental Chemistry,” Anal. Chem. 1980, 52, 2242–2249. 147 148 Analytical Chemistry 2.1 5A Analytical Standards To standardize an analytical method we use standards that contain known amounts of analyte. The accuracy of a standardization, therefore, depends on the quality of the reagents and the glassware we use to prepare these standards. For example, in an acid–base titration the stoichiometry of the acid–base reaction defines the relationship between the moles of analyte and the moles of titrant. In turn, the moles of titrant is the product of the See Chapter 9 for a thorough discussion of titrant’s concentration and the volume of titrant used to reach the equiva- titrimetric methods of analysis.
    [Show full text]
  • Isoprene Photochemistry Over the Amazon Rainforest
    Isoprene photochemistry over the Amazon rainforest Yingjun Liua, Joel Britob, Matthew R. Dorrisc, Jean C. Rivera-Riosc,d, Roger Secoe, Kelvin H. Batesf, Paulo Artaxob, Sergio Duvoisin Jr.g, Frank N. Keutscha,c,d, Saewung Kime, Allen H. Goldsteinh, Alex B. Guenthere,i, Antonio O. Manzij, Rodrigo A. F. Souzak, Stephen R. Springstonl, Thomas B. Watsonl, Karena A. McKinneya,1, and Scot T. Martina,m,1 aJohn A. Paulson School of Engineering and Applied Sciences, Harvard University, Cambridge, MA 02138; bDepartment of Applied Physics, University of São Paulo, São Paulo 05508, Brazil; cDepartment of Chemistry, University of Wisconsin-Madison, Madison, WI 53706; dDepartment of Chemistry and Chemical Biology, Harvard University, Cambridge, MA 02138; eDepartment of Earth System Science, University of California, Irvine, CA 92697; fDivision of Chemistry and Chemical Engineering, California Institute of Technology, Pasadena, CA 91125; gDepartment of Chemistry, Universidade do Estado do Amazonas, Manaus, AM 69050, Brazil; hDepartment of Environmental Science, Policy, and Management, University of California, Berkeley, CA 94720; iPacific Northwest National Laboratory, Richland, WA 99354; jInstituto Nacional de Pesquisas da Amazonia, Manaus, AM 69067, Brazil; kDepartment of Meteorology, Universidade do Estado do Amazonas, Manaus, AM 69050, Brazil; lDepartment of Environmental and Climate Sciences, Brookhaven National Laboratory, Upton, NY 11973; and mDepartment of Earth and Planetary Sciences, Harvard University, Cambridge, MA 02138 Edited by Mark H. Thiemens, University of California, San Diego, La Jolla, CA, and approved April 13, 2016 (received for review December 23, 2015) Isoprene photooxidation is a major driver of atmospheric chemistry forests like Amazonia where there are few anthropogenic NO over forested regions.
    [Show full text]
  • Single-Molecule Fluorescence Detection
    Proc. Nadl. Acad. Sci. USA Vol. 86, pp. 4087-4091, June 1989 Biophysics Single-molecule fluorescence detection: Autocorrelation criterion and experimental realization with phycoerythrin (laser-induced fluorescence/femtomolar sensitivity/fluorescence assays/phycoerythrin oligomers) KONAN PECK*, LUBERT STRYERt, ALEXANDER N. GLAZERt, AND RICHARD A. MATHIES* *Department of Chemistry, University of California, Berkeley, CA 94720; tDepartment of Cell Biology, Stanford University School of Medicine, Stanford, CA 94305; and tDepartment of Microbiology and Immunology, University of California, Berkeley, CA 94720 Contributed by Lubert Stryer, February 10, 1989 ABSTRACT A theory for single-molecule fluorescence ofindividual molecules. In this paper, we present a theory for detection is developed and then used to analyze data from single-molecule fluorescence detection and apply it in de- subpicomolar solutions of B-phycoerythrin (PE). The distri- tecting phycoerythrin at concentrations as low as 1 fM. bution of detected counts is the convolution of a Poissonian continuous background with bursts arising from the passage of individual fluorophores through the focused laser beam. The THEORY autocorrelation function reveals single-molecule events and Consider a solution of fluorophores flowing through a fo- provides a criterion for optimizing experimental parameters. cused laser beam. The emission from the illuminated volume The transit time of fluorescent molecules through the 120-fl consists of bursts of fluorescence from molecules passing imaged volume was 800 ps. The optimal laser power (32 mW through the beam superimposed on a continuous background at 514.5 nm) gave an incident intensity of 1.8 x 1023 due to Rayleigh and Raman scattering from the solvent (Fig. photons-cm 2.S-, corresponding to a mean time of 1.1 ns lA).
    [Show full text]
  • I Fluorescent Detection of Chiral Amino Acids
    i Fluorescent Detection of Chiral Amino Acids: A Micelle Approach Gengyu Du Yilong, Sichuan, China B.S. in Chemistry University of Science and Technology of China, Hefei, China, 2015 A Dissertation presented to the Graduate Faculty of the University of Virginia in Candidacy for the Degree of Doctor of Philosophy Department of Chemistry University of Virginia April 2020 ii Abstract Fluorescent Detection of Chiral Amino Acids: A Micelle Approach 1,1’-Bi-2-naphthol (BINOL)-based fluorescent probes have been developed as powerful tools for the molecular recognition of many chiral molecules. High sensitivity and enantioselectivity for chiral amino acids have been achieved in organic media, but the recognition in water media has been limited by their poor solubility in aqueous solution. By using a diblock copolymer PEG-PLLA, 3,3’-diformyl-BINOL was encapsulated into micelles to form a micelle probe. It allowed the detection of chiral lysine (Lys) both chemoselectively and enantioselectively in carbonate buffer solution. A limit of detection (LOD) of 848 nM and 2nd order fit of ee detection was obtained for D-Lys. The chemoselectivity was attributed to the selective reaction of Lys’s terminal amino groups with the probe. Series of monoformyl-BINOL with varying substituents were synthesized and engineered into micelle probes. These probes achieved specific detection of chiral tryptophan (Trp) both enantioselectively and chemoselectively in carbonate buffer solution, with LOD of 2.6 µM and 1st order fit of ee detection. A non-C2 symmetric molecule, 3,3’-diformyl-tetrahydro-BINOL, was fabricated into a micelle probe. It achieved specific detection of chiral His both enantioselectively and chemoselectively in carbonate buffer solution, with LOD of 107 nM and 2nd order fit of ee detection.
    [Show full text]
  • Viewed, Most SPME Extractions Are Performed in Aqueous Matrices.11,16 the Organic Solvent Most Likely Acted As an Interference with the Analyte Extraction
    A COMPARISON OF COMMON LABORATORY TECHNIQUES FOR THE ANALYSIS OF THIOCARBAMATE PESTICIDES A Thesis Presented to The Graduate Faculty of The University of Akron In Partial Fulfillment of the Requirements for the Degree Master of Science Tammy Schumacher Donohue August, 2012 A COMPARISON OF COMMON LABORATORY TECHNIQUES FOR THE ANALYSIS OF THIOCARBAMATE PESTICIDES Tammy Schumacher Donohue Thesis Approved: Accepted: ________________________________ ________________________________ Advisor Dean of the College Dr. Claire Tessier Dr. Chand Midha ________________________________ ________________________________ Faculty Reader Dean of the Graduate School Dr. Kim C. Calvo Dr. George R. Newkome ________________________________ ________________________________ Department Chair Date Dr. Kim C. Calvo ii ABSTRACT The United States Environmental Protection Agency has devised a set of regulations limiting the use of thiocarbamate pesticides for the health and safety of humans and the environment. These regulations dictate the maximum amount of thiocarbamate compounds that may be released or present in soil, waste, and groundwater. Therefore, it is important to be able to determine their concentration accurately and reproducibly. A study was conducted to determine the best way to identify and quantify six thiocarbamate herbicides using equipment commonly found in industrial laboratories. Three analytical methods were tested: gas chromatography-mass spectrometry, high performance liquid chromatography, and infrared spectroscopy. They were chosen for their common usage, broad application, and operative ability. A comparison of these methods was made to determine the most effective technique for thiocarbamate identification and quantification. iii DEDICATION To my husband, Chris, whose steadfast belief in me never wavered. Thank you for always letting me know you were behind me, no matter what. I love you.
    [Show full text]
  • 18.4.3.7 Detection and Quantification Capabilities
    18.4.3.7 Detection and quantification capabilities Among the most important Performance Characteristics of the Chemical Measurement Process (CMP) are those that can serve as measures of the underlying detection and quantification capabilities. These are essential for applications in research, international commerce, health, and safety. Such measures are important for planning measurements, and for selecting or developing CMPs that can meet specified needs, such as the detection or quantification of a dangerous or regulated level of a toxic substance. Equations 18.4.1-6 provide the basis for our considering the meaning of minimum detectable and minimum quantifiable amounts (signals, concentrations) in Analytical Chemistry. In each case, the determining factor is the distribution function of the estimated quantity (estimated net signal Sˆ , concentration or amount xˆ ). If normality can be assumed, it is sufficient to know the standard deviation of the estimated quantity as a function of S (or x). Detection limits (minimum detectable amounts) are based on the theory of hypothesis testing and the probabilities of false positives α, and false negatives ß. Quantification limits are defined in terms of a specified value for the relative standard deviation. It is important to emphasize that both types of limits are CMP Performance Characteristics, associated with underlying true values of the quantity of interest; they are not associated with any particular outcome or result. The detection decision, on the other hand, is result-specific; it is made by comparing the experimental result with the Critical Value, which is the minimum significant estimated value of the quantity of interest. Terminology. Unfortunately, a host of terms have been used within the chemical community to describe detection and quantification capabilities.
    [Show full text]
  • Guidance for the Validation of Analytical Methodology and Calibration of Equipment Used for Testing of Illicit Drugs in Seized Materials and Biological Specimens
    Vienna International Centre, PO Box 500, 1400 Vienna, Austria Tel.: (+43-1) 26060-0, Fax: (+43-1) 26060-5866, www.unodc.org Guidance for the Validation of Analytical Methodology and Calibration of Equipment used for Testing of Illicit Drugs in Seized Materials and Biological Specimens FOR UNITED NATIONS USE ONLY United Nations publication ISBN 978-92-1-148243-0 Sales No. E.09.XI.16 *0984578*Printed in Austria ST/NAR/41 V.09-84578—October 2009—200 A commitment to quality and continuous improvement Photo credits: UNODC Photo Library Laboratory and Scientific Section UNITED NATIONS OFFICE ON DRUGS AND CRIME Vienna Guidance for the Validation of Analytical Methodology and Calibration of Equipment used for Testing of Illicit Drugs in Seized Materials and Biological Specimens A commitment to quality and continuous improvement UNITED NATIONS New York, 2009 Acknowledgements This manual was produced by the Laboratory and Scientific Section (LSS) of the United Nations Office on Drugs and Crime (UNODC) and its preparation was coor- dinated by Iphigenia Naidis and Satu Turpeinen, staff of UNODC LSS (headed by Justice Tettey). LSS wishes to express its appreciation and thanks to the members of the Standing Panel of the UNODC’s International Quality Assurance Programme, Dr. Robert Anderson, Dr. Robert Bramley, Dr. David Clarke, and Dr. Pirjo Lillsunde, for the conceptualization of this manual, their valuable contributions, the review and finali- zation of the document.* *Contact details of named individuals can be requested from the UNODC Laboratory and Scientific Section (P.O. Box 500, 1400 Vienna, Austria). ST/NAR/41 UNITED NATIONS PUBLICATION Sales No.
    [Show full text]
  • Towards the 1000 Atom Detection Limit for 244Pu. R
    50th Lunar and Planetary Science Conference 2019 (LPI Contrib. No. 2132) 2978.pdf TOWARDS THE 1000 ATOM DETECTION LIMIT FOR 244PU. R. Trappitsch,1 M. R. Savina,1 J. M. Rolison,1 L. N. Harrison,1 and N. Dauphas2, 1Lawrence Livermore National Laboratory, Nuclear and Chemical Sciences Divi- sion, Livermore, CA 94551, ([email protected]) 2The University of Chicago, Enrico Fermi Institute, and Chicago Center for Cosmochemistry, Chicago, IL 60637 Introduction Plutonium-244 is a radionuclide with a size of ∼ 3% of the sample area we slowly desorbed half-life of 80 Ma that can only be produced by the rapid sample material from the surface, subsequently ionized neutron capture (r-) process. While the sources of the Pu neutrals using a three-color, three-photon resonance r-process are poorly constrained and heavily discussed ionization scheme, and then analyzed these photoions in [e.g.,1], optical spectroscopy of the neutron star merger a time-of-flight mass spectrometer. By assuming a ho- associated with the gravitational-wave event GW170817 mogeneous distribution of the sample material over the indicated the presence of freshly nucleosynthesized lan- surface we calculated that 2:6 × 105 239Pu, 3:7 × 104 thanides [2], a main product expected from r-process 240Pu, and 1:8 × 103 242Pu atoms were in the anal- nucleosynthesis calculations. Proxy measurements of ysis spot. Plutonium-238 and 241Pu atoms were also 244Pu in the early Solar System, measured via 244Pu in the analysis spot, however, interferences with non- fission-produced xenon in meteorites [3], show a rather resonantly ionized 238U and 241Am, respectively, pre- high abundance.
    [Show full text]
  • Bioanalytical Method Validation and Its Pharmaceutical Application
    A tica nal eu yt c ic a a m A r a c t Sonawane et al., Pharm Anal Acta 2014, 5:3 h a P DOI: 10.4172/2153-2435.1000288 ISSN: 2153-2435 Pharmaceutica Analytica Acta Review Article Open Access Bioanalytical Method Validation and Its Pharmaceutical Application- A Review Lalit V Sonawane*, Bhagwat N Poul, Sharad V Usnale, Pradeepkumar V Waghmare and Laxman H Surwase Department of Quality Assurance, MSS’s Maharashtra College of Pharmacy, Nilanga, Maharashtra, India Abstract Bioanalytical methods, based on a variety of physico-chemical and biological techniques such as chromatography, immunoassay and mass spectrometry, must be validated prior to and during use to give confidence in the results generated. It is the process used to establish that a quantitative analytical method is suitable for biomedical applications. Bioanalytical method validation includes all of the procedures that demonstrate that a particular method used for quantitative measurement of analytes in a given biological matrix, such as blood, plasma, serum, or urine is reliable and reproducible for the intended use. The present manuscript focuses on the consistent evaluation of the key bioanalytical validation parameters is discussed: accuracy, precision, sensitivity, selectivity, standard curve, limits of quantification, range, recovery and stability. These validation parameters are described, together with an example of validation methodology applied in the case of chromatographic methods used in bioanalysis, taking in account to the recent Food and Drug Administration (FDA) guidelines and EMA guidelines. Keywords: Bioanalytical method validation; Validation parameters; Bioanalytical method validation is vital not only in terms of Application; FDA and EMA guidelines regulatory submission but also for ensuring generation of high quality data during drug discovery and development.
    [Show full text]
  • Chiral Separation of Amines by Non-Aqueous Capillary Electrophoresis Using Low Molecular Weight Selectors
    Digital Comprehensive Summaries of Uppsala Dissertations from the Faculty of Pharmacy 31 Chiral Separation of Amines by Non-Aqueous Capillary Electrophoresis using Low Molecular Weight Selectors YLVA HEDELAND ACTA UNIVERSITATIS UPSALIENSIS ISSN 1651-6192 UPPSALA ISBN 91-554-6524-2 2006 urn:nbn:se:uu:diva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
    [Show full text]