DOCSLIB.ORG

Sanitary Sewer System Regulations

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Sanitary Sewer System Regulations CHAPTER 136 – SANITARY DISTRICT NO. 2 ARTICLE IX – SANITARY SEWER SYSTEM REGULATIONS A136-33 Purpose and Intent of this Article a. The purpose of this chapter is to promote and protect the public health, safety and general welfare of the residents of the Town, to enhance aquatic life, scenic and ecological values and enhance municipal, industrial and recreational use of water. b. The Sanitary District hereby adopts and incorporates herein the NEW Water (formerly Green Bay Metropolitan Sewerage District) Sewer Use Ordinance, dated October 20, 2016, and may be amended from time to time. In case of a direct conflict between this chapter and the NEW Water sewer use ordinance, the terms and conditions of the NEW Water sewer use ordinance shall prevail. c. The objectives of this chapter are to: 1. Prevent the introduction of pollutants into the Sanitary District wastewater system which will interfere with the normal operations of the system; 2. Prevent the introduction of pollutants into the wastewater system which do not receive adequate treatment at NEW Water, and which will pass through the system into receiving waters or the atmosphere or otherwise be incompatible with the system. d. Pursuant to Wis. Stats. 66.0813(3) the Town of Ledgeview Sanitary District #2 limits its wastewater treatment service area as shown on Attachment 1, Ledgeview Sanitary District Boundary and Sewer Service Area Map. This section does not limit the obligation to serve as it existed as of the effective date of this chapter. This section may be amended to expand such service area as provided in Wis. Stats. 66.0813(3). A136-34 Definitions Unless the context specifically indicates otherwise, the meaning of terms used in this chapter shall be as follows: Approving Authority means the Town of Ledgeview Sanitary District No. 2 Board BOD (Biochemical Oxygen Demand) – The quantity of oxygen utilized in the biochemical oxidation of organic matter, as determined by standard laboratory procedures in accordance with Wisconsin Administrative Code §NR Ch. 219. Building Drain shall mean that part of the lowest horizontal piping of a drainage system which receives the discharges from drainage pipes within the walls of a building and conveys it to a building sewer. Clear Water shall be defined as surface water, storm water, groundwater or unpolluted process waters. Clear water is prohibited from discharge into the sanitary sewer system. Debt Service Charge means a charge levied on the users of the sewer utility for the retirement of capital expenditures. Director of Public Works includes his/her written designee Commission shall mean the group of persons charged with control of the operations and maintenance of the Sanitary District. Compatible Pollutants means biochemical oxygen demand, suspended solids, phosphorus, ammonia, or pH, plus additional pollutants defined in the WPDES permit for the publicly owned treatment works receiving the pollutants if such works where designed to treat such additional pollutants to a substantial degree. Floatable Oil is oil, fat or grease in a physical state such that it will separate by gravity from wastewater by treatment in an approved pretreatment facility. A wastewater shall be considered free of floatable fat if it is properly pretreated and the wastewater does not interfere with the collection or pretreatment system. Garbage means the residue from the preparation, cooking and dispensing of food or the handling, storage or sale of food products or storage. Ground Garbage means garbage that has been shredded to such a degree that particles may be freely carried in suspension under normal sanitary sewer flow conditions. No particle may exceed one-half inch in any dimension. Incompatible Pollutants shall mean wastewater with any pollutant that will adversely affect or disrupt the quality of wastewater treatment. Industrial Waste means the wastewater from industrial processes, trade or business, as distinct from sanitary sewage, and the discharge from sewage pretreatment facilities. Infiltration means clear water entering the sanitary sewer system and service connections through means other than a direct discharge of clear water. Inflow means clear water entering the sanitary sewer system through a direct connection between the source of clear water and the sanitary sewer system. Inflow and Infiltration (I/I) means the combined volume of inflow and infiltration to the sanitary sewer system. Lateral means the extension from the public sewer or other place of disposal beginning outside the building wall May is permissible. Municipal Wastewater means the spent water of a community. From the standpoint of a source, it may be a combination of the liquid and water carried wastes from residences, commercial buildings, industrial buildings, industrial plants and institutions, together with any groundwater, surface water and storm water that may have inadvertently entered the sewerage system. Natural Outlet means any outlet, including storm sewers, into a watercourse, pond, ditch, lake or other body of surface water or groundwater. Person shall mean any or all persons including an individual, company, firm, municipal or private corporation, association, society, institution, enterprise, government agency or other entity. pH means the logarithm of the reciprocal of the hydrogen-ion concentration. The concentration is the weight Phosphorus means the element phosphorus as it is found in wastewater and quantified in accordance with procedures set forth in Standard Methods. Pollutant means any contaminant present in wastewater, including but not limited to, dredged spoils, incinerator residue, sewage, garbage, refuse, oil, solvents, flammables, sewage sludge, munitions, chemical wastes, biological materials, radioactive substances, heat, wrecked or discarded equipment, rocks, sand, soil, toxic substances and residential, commercial, industrial or agricultural waste. Pretreatment means the reduction, elimination or alteration of the pollutant properties prior to, or in lieu of, discharge into the sanitary sewer. Public Sewer means a sewer which is provided by or subject to the jurisdiction of the Sanitary District and will consist of the following increments: 1. Collector Sewer – A sewer whose primary purpose is to collect wastewaters from individual point source discharges. 2. Interceptor Sewer – A sewer whose primary purpose is to transport wastewater from collector sewers to a treatment facility. 3. Force Main – A pipe in which wastewater is carried under pressure. 4. Pumping Station – A station positioned in the public sewer system at which the wastewater is pumped to a higher elevation. Sanitary District shall refer to the Town of Ledgeview Sanitary District No. 2 and its governing commission. Sanitary Sewage means a combination of liquid and water carried wastes discharged from toilets and/or sanitary plumbing facilities, together with such ground, surface and storm waters as may have inadvertently entered the sewage system. Sanitary Sewer means a sewer that carries liquid and water carried wastes from residences, commercial buildings, industrial plants and institutions, together with small quantities of ground, storm and surface waters that are not admitted intentionally. Septage means the wastewater or contents of septic or holding tanks, dosing chambers, grease interceptors, seepage beds, seepage pits, seepage trenches, privies or portable restrooms. Septage does not include waste disposed at an authorized and designated dumping station for recreational vehicles. Sewage is spent water of a community also known as municipal wastewater. Sewer Service Area is the primary area presently serviced by the municipal wastewater sewage collection system and those areas within the Sanitary District identified by the Brown County Sewage Plan. Sewer Service Charge is a service charge levied on users of the wastewater collection and treatment facilities for payment of use-related capital expenses as well as the operation and maintenance costs, including replacement costs of said facilities. Sewer System means the common sanitary sewers within a sewerage system which are primarily installed to receive wastewaters directly from facilities which convey wastewater from individual structures or from private property, and which include service connection Wye fittings designed for connection with those facilities. Sewerage System means all structures, conduits and pipes, by which sewage is collected, treated, and disposed of, except plumbing inside and in connection with buildings served, and service pipes, from building to sewer main. Shall is mandatory. Slug Load means any substance released at a discharge rate and/or concentration which causes interference to wastewater treatment processes or plugging or surcharging of the sewer system. Standard Methods means the examination and analytical procedures set forth in the most recent edition of the “Standard Methods for the Examination of Water, Sewage and Industrial Wastes”, published jointly by the American Public Health Association, the American Water Works Association and the Federation of Sewage and Industrial Wastes Association. Storm Drain means a drain or sewer for conveying groundwater, water, subsurface water or unpolluted water from any source. Also referred to as a “storm sewer”. Storm Water Runoff means that portion of rainfall that is collected and drained into the storm sewer system. Suspended Solids means solids that either float on the surface or are in suspension in, water, wastewater
Load more

Recommended publications
  • Decentralized Systems Technology Fact Sheet: Septic Tank Systems for Large Flow Application
    United States Office of Water EPA 832-F-00-079 Environmental Protection Washington, D.C. September 2000 Agency Decentralized Systems Technology Fact Sheet Septic Tank Systems for Large Flow Applications DESCRIPTION Three main types of septic tanks are used for wastewater treatment: A septic tank system is a traditional wastewater treatment technology utilizing treatment in a tank • Concrete. system followed by soil absorption. The system operates on gravity and has been used in residential • Fiberglass. areas for decades. A modification to the traditional system is an enlargement to accommodate many • Polyethylene/plastic. homes and/or commercial discharges. This is accomplished with individual septic tanks followed All tanks must be watertight because groundwater by a community collection and subsurface disposal entering the system can saturate the soil absorption system, or a community collection system followed field, resulting in a failed system. Furthermore, in by a single treatment system. Commercial instances where septic tanks precede a secondary establishments, such as restaurants, nursing homes, treatment process, excess groundwater may hospitals and other public use areas do not generally inundate the downstream process, causing it to use septic tank systems due to oil & grease, odor, perform poorly. and flow issues. From the septic tank, the clarified wastewater The primary device in treatment is a septic tank passes through the tank outlet and enters the soil enclosed in a watertight container that collects and absorption field. The most common outlet is a tee provides primary treatment of wastewater by fitting connected to the pipe leading to the soil separating solids from the wastewater. The tank absorption field.
    [Show full text]
  • Grease Basins Approved For
    Lake County Department of Public Works List of Approved Grease Removal Systems and Sampling Stations The following lists Manufacturers of Grease Removal Systems and Sampling Stations. This list is provided as a service to the food service establishments by the Lake County Public Works Department and does not constitute an endorsement of any company listed on the following pages. The Lake County Public Works Department will accept grease removal units, other than those specified in this document, providing that the grease removal unit satisfies all criteria outlined in the County Sewer Use Ordinance and the Variance Procedure is properly followed. The following is a list of Passive Interior Device (PID) and Passive Exterior Device (PED) manufacturers and the acceptable model numbers. These devices recover and remove oils and grease from the effluent waste stream. The oils and grease recovered are manually pumped and can be recycled or disposed of in solid waste. Zurn Green Turtle Acceptable Models Proceptor® 2709 Water Ridge Parkway Suite 410 All GMC Models between Charlotte, NC 28217 GMC500- GMC1500 (704) 295-1733 *GMC250 (Min Interior) www.greenturtletech.com Schier Products Acceptable Models 9500 Woodend Road Great Basin Models Edwardsville, KS 66111 GB500 – GB1000 (913) 951-3399 Big Foot Models www.schierproducts.com GGI750- GGI1500 *GB250 (Min Interior) * Requires a variance for interior applications. The following is a list of Sampling Station manufacturers and the acceptable model numbers. Schier Products Acceptable Models 9500 Woodend Road Exterior: SV24-L4, SV24-L6, Edwardsville, KS 66111 SV24-O4, SV24-O6 (913) 951-3399 Interior: SV4-L4, SV4-L6, www.schierproducts.com SV4-O4 Automatic Recovery Devices Acceptable Models Thermaco Big Dipper PO Box 2548 Contact mfg.
    [Show full text]
  • State of Technology for Rehabilitation of Wastewater Collection Systems
    EPA/600/R-10/078 | July 2010 | www.epa.gov /nrmrl State of Technology for Rehabilitation of Wastewater Collection Systems Office of Research and Development National Risk Management Research Laboratory - Water Supply and Water Resources Division United States Office of Research EPA/600/R-10/078 Environmental Protection and Development July 2010 Agency Washington, DC 20460 State of Technology for Rehabilitation of Wastewater Collection Systems State of Technology for Rehabilitation of Wastewater Collection Systems by Dr. Ray Sterling, P.E., Jadranka Simicevic, Dr. Erez Allouche, P.E. Trenchless Technology Center at Louisiana Tech University Wendy Condit, P.E. Battelle Memorial Institute Lili Wang, P.E. ALSA Tech, LLC Contract No. EP-C-05-057 Task Order No. 58 Ariamalar Selvakumar, Ph.D., P.E. Task Order Manager U.S. Environmental Protection Agency Urban Watershed Branch National Risk Management Research Laboratory Water Supply and Water Resources Division 2890 Woodbridge Avenue (MS-104) Edison, NJ 08837 National Risk Management Research Laboratory Office of Research and Development U.S. Environmental Protection Agency Cincinnati, Ohio 45268 July 2010 DISCLAIMER The work reported in this document was funded by the U.S. Environmental Protection Agency (EPA) under Task Order (TO) 58 of Contract No. EP-C-05-057 to Battelle. Through its Office of Research and Development, EPA funded and managed, or partially funded and collaborated in, the research described herein. This document has been subjected to the Agency’s peer and administrative reviews and has been approved for publication. Any opinions expressed in this report are those of the authors and do not necessarily reflect the views of the Agency; therefore, no official endorsement should be inferred.
    [Show full text]
  • Fats, Oils and Grease (Fog)
    CITY OF TULSA FATS, OILS AND GREASE (FOG) One of the worst things that can happen to a home or business is discovering a sewage overflow due to plumbing problems. More often than not, when those overflows are investigated the cause is clear — fats, oils and grease (FOG) have clogged the pipes and prevented it from performing its duty. According to the Environmental Protection Agency, 47 percent of sanitary sewage overflows (SSOs) are caused by FOG. This is unsurprising when you learn that a single restaurant can contribute anywhere from 800 to 17,000 pounds of grease per year to our wastewater treatment plants. How Does FOG Cause Problems? Think of the pipes in our sewer system as the veins leading to the beating heart of the city — our wastewater treatment plant. When FOG is sent down the drain, particles separate from the water and cling to the walls of the pipes. As this continues, buildup occurs until a pipe is so clogged that it may be reduced to a fraction of its normal capacity. This reduction in size can lead to backflow and sewage overflow on your property or your downstream neighbor's property. If one of those areas of buildup hardens like plaque, it has the potential to break off and then cause a “heart attack” as it reaches the center of the system. Proper FOG disposal can prevent this kind of buildup and disruption to Tulsa’s wastewater system. Preventing FOG Buildup in Businesses For food-handling organizations, taking precautions to avoid sending Clean up spills immediately with disposable wipes or an FOG into the sewer system not only saves the city time and money but absorbent (e.g.
    [Show full text]
  • Fats, Oil and Grease (FOG) Policies and Procedures Manual
    Fats, Oil and Grease (FOG) Policies and Procedures Manual February 2018 Colorado Springs Utilities Industrial Pretreatment Program 701 East Las Vegas Street Colorado Springs, CO 80903 (719) 448-4800 . Table of Contents EXECUTIVE SUMMARY. ......................................................................................................................................... 1 . INTRODUCTION ................................. ........................................................................................................................ 1 DEFINITIONS ................................. .............................................................................................................................. 2 LEGAL AUTHORITY ................................ ................................................................................................................ 4 PRETREATMENT PROGRAM AUTHORITY .................................................................................................................... 4 FOG CONTROL AUTHORITY ....................................................................................................................................... 4 BMP REQUIREMENTS ............................................................................................................................................. 6 DESCRIPTION AND APPLICABILITY ............................................................................................................................. 6 FOOD SERVICE ESTABLISHMENTS .............................................................................................................................
    [Show full text]
  • Grease Interceptors
    Grease Interceptors The Journey Continues Introduction Obe Tejada Sewer Collections Superintendent City of Moab Other People of Note... Colby Means Sewer Service Worker III Marcie Mason Public Works Administrative Assistant We are going to talk about…. - Best Practices, Cleaning, and Retrofitting - Moab’s Grease By the Numbers... - Codes and Documents Related to Grease Regulation - Tests, Inspections, Compliance Letters, and Fines What is a Grease Interceptor/Trap? A grease trap (also known as grease interceptor) is a plumbing device (a type of trap) designed to intercept most greases and solids before they enter a wastewater disposal system. ... These reduce the amount of fats, oils and greases (FOGs) that enter sewers. How do they work? As the wastewater cools, the fat, oil, and grease (FOG) harden and the food solids settle. The FOG, being lighter than water, floats to the top of the grease trap. ... The FOG fills the grease trap from top down, displacing the wastewater from the middle of the grease trap and into the sanitary sewer or septic system. Grease Interceptor VS Mechanical Grease Trap Mechanical Grease Trap: ● Smaller, usually located under a sink or in a crawl space ● Easier and cheaper to install ● Need to be cleaned a lot more often (every few days to daily) Grease Interceptor: ● Large, (350 gal.+) usually located outside ● More expensive to install ● Need to be cleaned less often (every month to 6 months) Mechanical Grease Traps Grease Interceptors Best Practices The less you put in the less you take out... 1. Scrape plates aggressively with a rubber scraper/spatula into the trash before washing them 2.
    [Show full text]
  • Preventing Stormwater Pollution Information for Food Businesses
    Preventing stormwater pollution Information for food businesses THE STORMWATER DRAIN IS JUST FOR RAIN This project has been assisted by the Victorian Government through Melbourne Water Corporation as part of the Living Rivers Stormwater Program. Contents Our Councils Commitment ...........................................................................3 Top five things you can do to keep waterways clean! ................................4 What is stormwater? .......................................................................................6 What is stormwater pollution? .......................................................................7 Common types of stormwater pollutants and their effects ..............................7 Why is it important to prevent stormwater pollution? ................................8 Know your drains! ...........................................................................................9 How to prevent common causes of stormwater pollution ........................12 Waste management – waste water from cleaning ....................................14 Waste management – liquids and liquids waste .......................................15 Waste management – bins and solid rubbish ............................................16 Food and Oil Interceptors ‘Grease traps’ ...................................................17 Prepare your workplace and staff to avoid stormwater pollution! ..........18 Work with your community ..........................................................................19 Further
    [Show full text]
  • Collier Township Municipal Authority Grease Removal Requirements and Procedures April, 2009
    COLLIER TOWNSHIP MUNICIPAL AUTHORITY GREASE REMOVAL REQUIREMENTS AND PROCEDURES APRIL, 2009 Prepared By: NIRA Consulting Engineers, Inc. 950 Fifth Avenue Coraopolis, PA 15108 Phone: (412) 262-3970 (Fax): (412) 262-1938 E-mail: [email protected] Collier Township Municipal Authority Grease Removal Requirements and Procedures Index Page Introduction 1 How Grease Removal Systems Work 1 What is a Grease Trap 1 Inside Grease Trap Installation 2 What is a Grease Interceptor 3 Outside Grease Interceptor Installation 3 What is a Solids Interceptor/Separator 4 Inside Grease Trap Requirements 5 Outside Grease Interceptor Requirements 5 Operational Requirements 5 Maintenance/Inspection Log 7 Sizing inside Grease Traps 8 Single Fixtures 8 M u l t i -Fixtures 9 Sizing Outside Grease Interceptor 10 Example #1 10 Example #2 11 Best Management Practices (BMP) 12 Grease Trap/Interceptor Log Introduction Restaurants and other food service businesses generate literally tons of fats, oils and grease (FOG) waste every day. If this waste is not managed properly, it can cause major environmental problems. Some of the FOG waste generated by these businesses is in solid form and can be properly disposed of in the trash. However, liquid waste containing FOG when improperly discharged to the municipal sewer system will build up inside sewer lines and cause wastewater overflows to occur inside the restaurant or elsewhere in the sewer system. This can cause a major disruption in the operation of a business, be a significant public health hazard, and be very expensive to clean- up. If your business generates greasy wastewater, you can reduce the likelihood of a sewer back- up by adopting good housekeeping practices and minimizing the amount of FOG waste that go down your drains by installing and properly maintaining a grease removal system.
    [Show full text]
  • Grease Traps 101
    GREASE TRAPS 101 Environmental Grease traps operate on very simple principles... Fats, oils and grease (FOG) are lighter than water and as a result, float. The grease trap has a low inlet pipe and a baffle (barrier) to slow the velocity of the water coming in. This gives time for the solids to settle and the FOG to float. Air pressure forces water to discharge from the outlet pipe near the bottom of the trap. Since the FOG is floating on the top, only a minimal amount of FOG is discharged with the water. Grease traps must be maintained on a regular basis... In order to prevent FOG from entering sewer lines and causing backups, grease traps must be inspected and cleaned on a regular basis. Grease traps in active use should be cleaned at least once every three months or when the accumulation FOG and settled solids reaches 25% of the grease interceptor’s overall liquid depth - whichever occurs first. Sewer backups caused by grease chokes can be costly... The Sewerage and Water Board of New Orleans holds business owners liable for ALL costs associated with the removal of FOG from the sewer system, including damage to adjoining personal property, parking lots, streets, and sewer system repair. Call S&WB, Environmental Affairs at (504) 942-3856 for more information or visit http://www.swbno.org/environmental.asp Understanding Grease Removal and the 25% Rule Per Section16.5 of the Plumbing Code, all food service establishments must have grease removal devices maintained by a Sewerage & Water Board permitted transporter when they reach 25% of the design capacity OR a minimum of quarterly.
    [Show full text]
  • Sewer Use Ordinance 6-9-2014
    SEWER USE ORDINANCE NO. 6-9-2014 This Ordinance replaces Ordinances 11-14-2011, 7-13-87B, FOG Ordinance 05-09-11, and INFLOW AND INFILTRATION ORDINANCE 12-08-08. BE IT ORDAINED BY THE BOARD OF TRUSTEES OF THE CLAY TOWNSHIP REGIONAL WASTE DISTRICT (HEREIN REFERRED TO AS THE "DISTRICT") This Ordinance regulates the connection to and use of public and private sewers and drains, the installation and connection of building sewers, and the discharge of waters and wastes into the sewerage system of the Clay Township Regional Waste District, and provides rates and charges for violations thereof. CONTENTS SECTION 1-GENERAL PROVISIONS ......................................................... 2 SECTION 2-GENERAL SEWER USE & CONNECTION ........................... 2 SECTION 3-DISCHARGE PROHIBITIONS ................................................. 5 SECTION 4- LIMITATIONS ON WASTEWATER STRENGTH ................ 8 SECTION 5-FATS, OILS & GREASE (FOG) REQUIREMENTS ............... 9 SECTION 6-INDUSTRIAL WASTEWATER DISCHARGES ................... 14 SECTION 7-COMPLIANCE MONITORING .............................................. 16 SECTION 8- ADMINISTRATIVE ENFORCEMENT REMEDIES ........... 17 SECTION 9- JUDICIAL ENFORCEMENT REMEDIES ............................ 19 SECTION 11-FEES ....................................................................................... 20 SECTION 12- MISCELLANEOUS PROVISIONS ..................................... 23 SECTION 13- SPECIFIC DEFINITIONS………………………………….24 Sewer Use Ordinance No. 6‐9‐2014 1 SECTION 1-General Provisions
    [Show full text]
  • Frequently Asked Questions Used Water
    Frequently Asked Questions Used Water Published: 7 November 2017 Last Updated: 9 July 2018 Contents General Enquiries ............................................................................................................................... 4 1. What is a public sewerage system? ................................................................................... 4 2. Can the new sewers (which are to be handed over to PUB for maintenance) be laid within private property or state land? ................................................................................................ 4 3. What is greywater recycling? .......................................................................................... 4 4. Why are there public sewers/manholes within premises of landed property? ....................... 4 5. Can the public sewer/manhole within my premises/lot be shifted to outside my property? .... 5 Queries associated with sewer connections .......................................................................................... 5 1. When re-developing or reconstructing a building, can the existing sewer connection line be reused? 5 2. Can a sewer connection be constructed to the inspection chamber or manhole (public sewer) at the neighbouring premises? ......................................................................................................... 6 3. What can a property owner do if the only available public sewer/manhole is located within a neighbouring lot?.....................................................................................................
    [Show full text]
  • 8.1 Introduction
    CHAPTER 8 APPURTENANCES 8.1 Introduction This chapter discusses several types of equipment used in onsite waste- water treatmenl 'disposal systems-that have 'general application to the components prev ously presented. The following items are covered: 1. Grease traps (or grease interceptors) 2. Dosing chambers 3. Flow d version methods Grease traps are used to remove excessive amounts of grease that may interfere with subsequent treatment. Dosing chambers are necessary when raw or partially treated wastewater must be lifted or dosed in large periodic volumes. Flow diversion valves are used when alternating use of treatment or disposal components is employed. These components are described as to applicability, performance, design criteria, construc- tion features, and operation and maintenance. 8.2 Grease Traps 8.2.1 Description In some instances, the accumulation of grease can be a problem. In cer- tain commercial/institutional applications, grease can clog sewer lines and inlet and outlet structures in septic tanks, resulting in restricted flows and poor septic tank performance. The purpose of a grease trap is simply to remove grease from the wastewater stream prior to treatment. Grease traps are small flotation chambers where grease floats to the water surface and is retained while the clearer water underneath is dis- charged. There are no moving mechanical parts, and the design is simi- lar to that of a septic tank. 321 The grease traps discussed here are the large., outdoor-type units, and should not to be confused with the small grease traps found on some kitchen drains. 8.2.2 Application Grease traps are very rarely used for individual homes.
    [Show full text]