DVB); Framing Structure, Channel Coding and Modulation for Digital Terrestrial Television

Total Page:16

File Type:pdf, Size:1020Kb

DVB); Framing Structure, Channel Coding and Modulation for Digital Terrestrial Television Final draft ETSI EN 300 744 V1.6.1 (2008-09) European Standard (Telecommunications series) Digital Video Broadcasting (DVB); Framing structure, channel coding and modulation for digital terrestrial television European Broadcasting Union Union Européenne de Radio-Télévision EBU·UER 2 Final draft ETSI EN 300 744 V1.6.1 (2008-09) Reference REN/JTC-DVB-234 Keywords audio, broadcasting, data, digital, DVB, MPEG, terrestrial, TV, video ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88 Important notice Individual copies of the present document can be downloaded from: http://www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http://portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the following services: http://portal.etsi.org/chaircor/ETSI_support.asp Copyright Notification No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media. © European Telecommunications Standards Institute 2008. © European Broadcasting Union 2008. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTM, TIPHONTM, the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. ETSI 3 Final draft ETSI EN 300 744 V1.6.1 (2008-09) Contents Intellectual Property Rights ................................................................................................................................ 5 Foreword ............................................................................................................................................................. 5 1 Scope ........................................................................................................................................................ 6 2 References ................................................................................................................................................ 6 2.1 Normative references ......................................................................................................................................... 7 2.2 Informative references ........................................................................................................................................ 7 3 Definitions, symbols and abbreviations ................................................................................................... 7 3.1 Definitions .......................................................................................................................................................... 7 3.2 Symbols .............................................................................................................................................................. 7 3.3 Abbreviations ..................................................................................................................................................... 8 4 Baseline system ........................................................................................................................................ 9 4.1 General considerations ....................................................................................................................................... 9 4.2 Interfacing ........................................................................................................................................................ 11 4.3 Channel coding and modulation ....................................................................................................................... 11 4.3.1 Transport multiplex adaptation and randomization for energy dispersal .................................................... 11 4.3.2 Outer coding and outer interleaving............................................................................................................ 12 4.3.3 Inner coding ................................................................................................................................................ 14 4.3.4 Inner interleaving ........................................................................................................................................ 15 4.3.4.1 Bit-wise interleaving ............................................................................................................................. 15 4.3.4.2 Symbol interleaver ................................................................................................................................ 19 4.3.5 Signal constellations and mapping .............................................................................................................. 21 4.4 OFDM frame structure ..................................................................................................................................... 25 4.5 Reference signals .............................................................................................................................................. 27 4.5.1 Functions and derivation ............................................................................................................................. 27 4.5.2 Definition of reference sequence ................................................................................................................ 27 4.5.3 Location of scattered pilot cells .................................................................................................................. 28 4.5.4 Location of continual pilot carriers ............................................................................................................. 29 4.5.5 Amplitudes of all reference information ..................................................................................................... 29 4.6 Transmission Parameter Signalling (TPS) ....................................................................................................... 29 4.6.1 Scope of the TPS ........................................................................................................................................ 30 4.6.2 TPS transmission format ............................................................................................................................. 31 4.6.2.1 Initialization .......................................................................................................................................... 31 4.6.2.2 Synchronization .................................................................................................................................... 31 4.6.2.3 TPS length indicator .............................................................................................................................. 31 4.6.2.4 Frame number ....................................................................................................................................... 32 4.6.2.5 Constellation ......................................................................................................................................... 32 4.6.2.6 Hierarchy information ........................................................................................................................... 32 4.6.2.7 Code rates .............................................................................................................................................. 32 4.6.2.8 Guard Intervals ...................................................................................................................................... 33 4.6.2.9 Transmission mode ............................................................................................................................... 33 4.6.2.10 Cell identifier ........................................................................................................................................ 33 4.6.2.11 Error protection of TPS ......................................................................................................................... 34 4.6.3 TPS modulation .......................................................................................................................................... 34 4.7 Number of RS-packets per OFDM super-frame ............................................................................................... 34 4.8 Spectrum characteristics and spectrum mask ................................................................................................... 35 4.8.1 Spectrum characteristics ............................................................................................................................. 35 4.8.2 Out-of-band spectrum mask (for 8 MHz channels) ...................................................................................
Recommended publications
  • History of the DVB Project
    History of the DVB Project (This article was written by David Wood around 2013.) Introduction The DVB Project is an Alliance of about 200 companies, originally of European origin but now worldwide. Its objective is to agree specifications for digital media delivery systems, including broadcasting. It is an open, private sector initiative with an annual membership fee, governed by a Memorandum of Understanding (MoU). Until late 1990, digital television broadcasting to the home was thought to be impractical and costly to implement. During 1991, broadcasters and consumer equipment manufacturers discussed how to form a concerted pan-European platform to develop digital terrestrial TV. Towards the end of that year, broadcasters, consumer electronics manufacturers and regulatory bodies came together to discuss the formation of a group that would oversee the development of digital television in Europe. This so-called European Launching Group (ELG) expanded to include the major European media interest groups, both public and private, the consumer electronics manufacturers, common carriers and regulators. It drafted the MoU establishing the rules by which this new and challenging game of collective action would be played. The concept of the MoU was a departure into unexplored territory and meant that commercial competitors needed to appreciate their common requirements and agendas. Trust and mutual respect had to be established. The MoU was signed by all ELG participants in September 1993, and the Launching Group renamed itself as the Digital Video Broadcasting Project (DVB). Development work in digital television, already underway in Europe, moved into top gear. Around this time a separate group, the Working Group on Digital Television, prepared a study of the prospects and possibilities for digital terrestrial television in Europe.
    [Show full text]
  • DTMB, ATSC, ISDB-T, DVB T/T2) and Radio & Emergency Warning Broadcasting System
    Session 3 Broadcasting Standards for digital television (DTMB, ATSC, ISDB-T, DVB T/T2) and radio & Emergency Warning Broadcasting System 2015 Kuala Lumpur, Malaysia Dr AMAL Punchihewa Director ABU Technology Asia-Pacific Broadcasting Union A Vice Chair of World Broadcasting Union Technical Committee (WBU-TC) Dr Amal Punchihewa © Director of Technology ABU & A Vice Chair of World Broadcasting Union Technical Committee (WBU-TC) DTMB, ATSC, DVB and ABU working on EWS 2.0 , looking at Asia-Pacific requirements and building a reference model Dr Amal Punchihewa PhD, MEEng, BSC(Eng)Hons, CEng, FIET, FIPENZ, SMIEEE, MSLAAS, MCS Postgraduate Studies in Business Administration Director ABU Technology Asia-Pacific Broadcasting Union Kuala Lumpur, Malaysia A Vice-Chair World Broadcasting Unions Technical Committee (WBU-TC) Dr Amal Punchihewa © Director of Technology ABU & A Vice Chair of World Broadcasting Union Technical Committee (WBU-TC) 2 Outline • Digital Broadcasting • Television Services – Free TV or Pay TV – OTA or Cable • DTV Standards • What are EWS – Content delivered from distance, Live, VOD, …. Dr Amal Punchihewa © Director of Technology ABU & A Vice Chair of World Broadcasting Union Technical Committee (WBU-TC) 3 Traditional TV Traditional Broadcasting • Linear TV – At scheduled times, missed it then catch the delayed version, … • Public or commercial – Funding or business model, FTA, adverting, License fee, subscription, … • Terrestrial, Satellite, Cable – Now cloud, IP etc. … • Return channel – One-to-many service, no return channel
    [Show full text]
  • NTE15039 Integrated Circuit VHS/VCR Chroma Signal Proessor for NTSC/PAL/SECAM Systems
    NTE15039 Integrated Circuit VHS/VCR Chroma Signal Proessor for NTSC/PAL/SECAM Systems Description: The NTE15039 is a multifunctional IC in a 24–Lead DIP type package that contains VHS VCT chroma signal processing circuitry. Since the package is small and a minimum number of external compo- nents are required, the NTE15039 occupies much less space on the PC board thus facilitating VCR design. The chroma section is made adjustment–free (except REC chroma level) thus streamlining the manufacture of VCRs Features: D Designed for NTSC/PAL/MESECAM Systems D Adjustment–Free Chroma Section (Except REC Chroma Level) D Few External Components Required D LPF Usable for REC/PB D Multifunctional: 2fSC Generator for CCD Drive Function to Select APC Loop Input Signal Passed/Not Passed Through Comb Filter 3rd Lock Protector of VXO Absolute Maximum Ratings: (TA = +25°C unless otherwise specified) Maximum Supply Voltage, VCCmax. 7V Allowable Power Dissipation (TA ≤ +65°C), PDmax. 850mW Operating Temperature Range, Topg . –10° to +65°C Storage Temperature Range, Tstg . –40° to +125°C Recommended Operating Conditions: (TA = +25°C unless otherwise specified) Recommended Supply Voltage, VCC . 5V Operating Voltage Range, VCCop. 4.8 to 5.5V Electrical Characteristics: (TA = +25°C, VCC = 5V unless otherwise specified) Parameter Symbol Test Conditions Min Typ Max Unit REC Current Dissipation ICC(R) 49 62 75 mA REC Output Level VO(R) 75 110 145 mVP–P REC ACC Characteristics ∆VO(R) Input ± 6dB –0.5 ±0.1 +0.5 dB Electrical Characteristics (Cont’d): (TA = +25°C, VCC
    [Show full text]
  • Digital Television and the Allure of Auctions: the Birth and Stillbirth of DTV Legislation
    Federal Communications Law Journal Volume 49 Issue 3 Article 2 4-1997 Digital Television and the Allure of Auctions: The Birth and Stillbirth of DTV Legislation Ellen P. Goodman Covington & Burling Follow this and additional works at: https://www.repository.law.indiana.edu/fclj Part of the Communications Law Commons, and the Legislation Commons Recommended Citation Goodman, Ellen P. (1997) "Digital Television and the Allure of Auctions: The Birth and Stillbirth of DTV Legislation," Federal Communications Law Journal: Vol. 49 : Iss. 3 , Article 2. Available at: https://www.repository.law.indiana.edu/fclj/vol49/iss3/2 This Article is brought to you for free and open access by the Law School Journals at Digital Repository @ Maurer Law. It has been accepted for inclusion in Federal Communications Law Journal by an authorized editor of Digital Repository @ Maurer Law. For more information, please contact [email protected]. Digital Television and the Allure of Auctions: The Birth and Stillbirth of DTV Legislation Ellen P. Goodman* I. INTRODUCTION ................................... 517 II. ORIGINS OF THE DTV PRovIsIoNs OF THE 1996 ACT .... 519 A. The Regulatory Process ..................... 519 B. The FirstBills ............................ 525 1. The Commerce Committee Bills ............. 526 2. Budget Actions ......................... 533 C. The Passage of the 1996Act .................. 537 Ill. THE AFTERMATH OF THE 1996 ACT ................ 538 A. Setting the Stage .......................... 538 B. The CongressionalHearings .................. 542 IV. CONCLUSION ................................ 546 I. INTRODUCTION President Clinton signed into law the Telecommunications Act of 1996 (1996 Act or the Act) on February 8, 1996.1 The pen he used to sign the Act was also used by President Eisenhower to create the federal highway system in 1957 and was later given to Senator Albert Gore, Sr., the father of the highway legislation.
    [Show full text]
  • Digital Television Systems
    This page intentionally left blank Digital Television Systems Digital television is a multibillion-dollar industry with commercial systems now being deployed worldwide. In this concise yet detailed guide, you will learn about the standards that apply to fixed-line and mobile digital television, as well as the underlying principles involved, such as signal analysis, modulation techniques, and source and channel coding. The digital television standards, including the MPEG family, ATSC, DVB, ISDTV, DTMB, and ISDB, are presented toaid understanding ofnew systems in the market and reveal the variations between different systems used throughout the world. Discussions of source and channel coding then provide the essential knowledge needed for designing reliable new systems.Throughout the book the theory is supported by over 200 figures and tables, whilst an extensive glossary defines practical terminology.Additional background features, including Fourier analysis, probability and stochastic processes, tables of Fourier and Hilbert transforms, and radiofrequency tables, are presented in the book’s useful appendices. This is an ideal reference for practitioners in the field of digital television. It will alsoappeal tograduate students and researchers in electrical engineering and computer science, and can be used as a textbook for graduate courses on digital television systems. Marcelo S. Alencar is Chair Professor in the Department of Electrical Engineering, Federal University of Campina Grande, Brazil. With over 29 years of teaching and research experience, he has published eight technical books and more than 200 scientific papers. He is Founder and President of the Institute for Advanced Studies in Communications (Iecom) and has consulted for several companies and R&D agencies.
    [Show full text]
  • The Transition to Digital Television*
    DIGITAL TELEVISION 1 The Transition to Digital Television* Jérôme Addaa and Marco Ottavianib University College London; London Business School This paper studies the role of economic policy for the transition from analogue to digital television, with particular attention to the switch off of the analogue terrestrial signal. The analogue signal cannot be credibly switched off until almost all viewers have migrated to digital, due to universality of access to television. But before switch off, only part of the population can be reached with the digital signal. In addition, those who are reached need to spend more to upgrade their reception equipment than after switch off, because the capacity to increase the power of the digital signal will be made available only then. After reviewing the competitive structure and the role of government intervention in television markets, we present the early experience of a number of industrialised countries in the transition to digital television. We then formulate a micro-econometric model of digital television adoption by individual viewers. The model is calibrated to UK data and simulated to predict the impact of government policies on the take up of digital television. Policy makers can affect the speed of take up of digital television by: (i) controlling the quality of the signals and the content of public service broadcasters; (ii) intervening in the market for digital equipment with subsidies; and (iii) publicising the conditions and date of switch off of the analogue signal. We find that if the analogue terrestrial signal is switched off conditionally on aggregate adoption, strategic delays possibly arise and expectations affect the success of the switch off policy.
    [Show full text]
  • Research on the Safe Broadcasting of Television Program
    MATEC Web of Conferences 63, 04002 (2016) DOI: 10.1051/matecconf/20166304002 MMME 2016 Research on the Safe Broadcasting of Television Program Jin Bao SONG1,a, Jin Hong SONG2 and Jian Ping CHAI1 1Information Engineering School, Communication University of China, Beijing, China 2Shandong Gold Mining Jiaojia Gold Mine (Laizhou) co.,LTD Abstract. The existing way of broadcasting and television monitoring has a lot of problems in China. On the basis of the signal technical indicators monitoring in the present broadcasting and television monitoring system, this paper further extends the function of the monitoring network in order to broaden the services of monitoring business and improve the effect and efficiency of monitoring work. The problem of identifying video content and channel in television and related electronic media is conquered at a low cost implementation way and the flexible technology mechanism. The coverage for video content and identification of the channel is expanded. The informative broadcast entries are generated after a series of video processing. The value of the numerous broadcast data is deeply excavated by using big data processing in order to realize a comprehensive, objective and accurate information monitoring for the safe broadcasting of television program. 1 Introduction paper is the development of cheap monitoring hardware devices which can be widely deployed to the village, so The existing way of broadcasting and television the actual situation of the user terminal broadcasting can monitoring has a lot of problems in China. Firstly, the be monitored by the administration of radio, film and existing way of monitoring is the front-end monitoring television.
    [Show full text]
  • ATSC 3 Digital Television Implementation for Public Television
    Meintel, Sgrignoli & Wallace CPB A Report To The Corporation for Public Broadcasting Regarding ATSC 3 Digital Television Implementation for Public Television Dennis Wallace MEINTEL, SGRIGNOLI, & WALLACE, LLC 1282 Smallwood Drive, Suite 372 Waldorf, MD 20603 (202) 251-7589 January 31, 2018 ATSC 3 Implementation 1 of 27 Meintel, Sgrignoli & Wallace CPB Executive Summary The firm of Meintel, Sgrignoli, and Wallace, LLC (MSW) is pleased to provide the following report to the Corporation for Public Broadcasting (CPB) regarding the adoption and implementation of the ATSC 3 television standard. Specifically, MSW was tasked with studying the potential impacts and opportunities for public television (PTV) stations as the new ATSC 3 television standard is implemented by broadcasters. The purpose of this report is to highlight some of the technological advances and focus on some of the potential opportunities and business considerations, as well as to generally outline the transition plan for TV broadcasters to transition to ATSC 3 in their respective markets. PTV broadcasters are particularly interested in ATSC 3 as an opportunity to provide new and innovative services to their audiences and communities, as well as to explore new revenue models that may be attractive in today’s environment. Additionally, PTV broadcasters, with their specific missions, are particularly well suited to benefit from the advances available in ATSC 3. However, with all the excitement of new services, new highly-efficient technologies, and new potential business models, PTV stations must also approach ATSC 3 with feasible business plans while minimizing financial risk to their organizations. As ATSC 3 is deployed and implemented across the United States, stations must also safeguard their existing operations, organizational missions, and financial resources in order to take full advantage of ATSC 3 once it is fully deployed and viable.
    [Show full text]
  • Amateur Extra License Class
    Amateur Extra License Class 1 Amateur Extra Class Chapter 8 Radio Modes and Equipment 2 1 Modulation Systems FCC Emission Designations and Terms • Specified by ITU. • Either 3 or 7 characters long. • If 3 characters: • 1st Character = The type of modulation of the main carrier. • 2nd Character = The nature of the signal(s) modulating the main carrier. • 3rd Character = The type of information to be transmitted. • If 7 characters, add a 4-character bandwidth designator in front of the 3-character designator. 3 Modulation Systems FCC Emission Designations and Terms • Type of Modulation. N Unmodulated Carrier A Amplitude Modulation R Single Sideband Reduced Carrier J Single Sideband Suppressed Carrier C Vestigial Sideband F Frequency Modulation G Phase Modulation P, K, L, M, Q, V, W, X Various Types of Pulse Modulation 4 2 Modulation Systems FCC Emission Designations and Terms • Type of Modulating Signal. 0 No modulating signal 1 A single channel containing quantized or digital information without the use of a modulating sub-carrier 2 A single channel containing quantized or digital information with the use of a modulating sub-carrier 3 A single channel containing analog information 7 Two or more channels containing quantized or digital information 8 Two or more channels containing analog information X Cases not otherwise covered 5 Modulation Systems FCC Emission Designations and Terms • Type of Transmitted Information. N No information transmitted A Telegraphy - for aural reception B Telegraphy - for automatic reception C Facsimile D Data transmission, telemetry, telecommand E Telephony (including sound broadcasting) F Television (video) W Combination of the above X Cases not otherwise covered 6 3 Modulation Systems FCC Emission Designations and Terms • 3-character designator examples: • A1A = CW.
    [Show full text]
  • DVB-T Transmissions – Interference with Adjacent-Channel PAL Services
    DVB-T DVB-T transmissions – interference with adjacent-channel PAL services R. Poole BBC Research & Development In the UK, many of the new digital television (DVB-T) services are broadcast in adjacent channels to existing PAL services. There have been reports of PAL reception suffering as a result, possibly because the maximum DVB-T sideband levels have been incorrectly specified. This article describes how to calculate the PAL picture impairment arising from the presence of DVB-T sidebands. It also compares the calculated predictions with experimental data. The conclusion is that the sideband specification is correct: critical viewers would just notice worst-case interference. However, it is possible to misinterpret the specification. An allowance must be made for the difference in effective radiated powers between the DVB-T and PAL transmissions. An example is given of how a mistake could be made. Introduction There have been reports that some of the new digital television transmissions have been caus- ing interference to existing PAL services in adjacent channels. Such interference could result from three possible mechanisms: inadequate adjacent-channel selectivity of the PAL television receivers; overloading of the receivers caused by the additional signals; generation of spurious sidebands within the DVB-T transmitters themselves. Work has already been carried out on the adjacent-channel performance of domestic PAL receivers: BBC R&D, for example, has carried out practical tests on receivers which were reported in an internal technical note (these tests are referred to at several points in this arti- cle). If the interfering DVB-T signal is “clean” or “ideal”, interference only becomes visible when its level exceeds that of the PAL signal.
    [Show full text]
  • Experience DTV Using LCD TV
    Experiencing DTV on the LCD TV What is DTV? DTV stands for Digital Television, the latest standard and the future of television broadcasting. Unlike analog TV, DTV is broadcast digitally to transmit an audio and video signal for movie-like picture quality and surround sound. HDTV, your ticket to movie theater experiences on your home TV set, is a Digital TV (DTV) format. There are many benefits to DTV, as we will explain below. In addition, on February 1st, 2006, Congress passed a law mandating that all analog TV broadcasts must cease on February 17, 2009. At present, many television stations have begun broadcasting programs digitally. Benefits of Digital Television Improved image and sound quality Digital signals are not prone to interference during transmission, resulting in high fidelity signals all the way to the TV set for immaculate colors, incredible image sharpness and great sound. With DTV we can say goodbye to “ghosting” and “snow” on the TV screen and noise from the speakers. In addition, DTV supports high quality picture formats such as HDTV, meaning you will be able to enjoy movie-like programming right in the comfort of your own living room! Interactive programming With analog TV, we could do very little else with our TV programs other than change the channel. DTV provides us with an interactive viewing experience, a good example of which is the ability to order whichever program we please directly through the TV. That was impossible in the analog TV age. DTV Picture Quality Levels There is more than one DTV picture quality level or format.
    [Show full text]
  • Digital Multi–Programme TV/HDTV by Satellite
    Digital multi–programme TV/HDTV by satellite M. Cominetti (RAI) A. Morello (RAI) M. Visintin (RAI) The progress of digital technology 1. Introduction since the WARC’77 is considered and the perspectives of future The significant progress of digital techniques in applications via satellite channels production, transmission and emission of radio are identified. Among these, digital and television programmes is rapidly changing the established concepts of broadcasting. multi–programme television systems, with different quality levels (EDTV, SDTV) and possible The latest developments in VLSI (very–large scale evolution to HDTV, are evaluated in integration) technology have significantly contrib- uted to the rapid emergence of digital image/video terms of picture quality and service compression techniques in broadcast and informa- availability on the satellite channels tion–oriented applications; optical fibre technolo- of the BSS bands (12 GHz and gy allows broadband end–to–end connectivity at 22 GHz) and of the FSS band (11 very high bit–rates including digital video capabil- GHz) in Europe. A usable channel ities; even the narrow–band terrestrial broadcast capacity of 45 Mbit/s is assumed, as channels in the VHF/UHF bands (6–7 MHz and 8 well as the adoption of advanced MHz) are under investigation, in the USA [1] and channel coding techniques with in Europe [2], for the future introduction of digital QPSK and 8PSK modulations. For television services. high and medium–power satellites, in operation or planned, the The interest for digital television in broadcasting receiving antenna diameters and multimedia communications is a clear exam- required for correct reception are ple of the current evolution from the analogue to reported.
    [Show full text]