Grandfather Clock Instructions

Total Page:16

File Type:pdf, Size:1020Kb

Grandfather Clock Instructions GRANDFATHER CLOCK INSTRUCTIONS Congratulations! You are now the proud owner of a fine timepiece. It has been carefully designed and crafted to give you years of dependable operation. Read this booklet thoroughly before assembling and operating your clock in order to become familiar with its many features and assure proper performance. Keep these instructions in a safe place for future reference. ATTENTION In order to ensure that your clock is stable, adjust the levelers at the bottom of the clock. As an added safety feature, a support strap has been provided that is fixed to the top of the clock and must be attached to the wall. It is recommended that you do so. HOW TO ASSEMBLE YOUR CLOCK CABINET 1. Carefully unpack all parts and compare each item to the following list to be sure you have everything required. QUANTITY DESCRIPTION 1 Base Unit 2 Side Panels 1 Top Unit (with door, dial and movement) 1 Back Panel 1 Front Door with Glass (hinges on right) 1 Pendulum 8 Screws (Phillips head) 8 Washers 2 Weights 2 Hinge Pins 2. Place the BASE UNIT near its final position but leave it away from the wall until the assembly is finished. 1 3. Fit the SIDE PANEL without hinges into the grooves in the base unit on the left side of the clock and attach it from the inside with two of the SCREWS and the FLAT WASHERS (Figure A) using a Phillips head screwdriver. Repeat the process using the side panel with the hinges on the right side of the clock. 4. Fit the BACK PANEL into the grooves in the side panels at the back of the cabinet and the bottom unit (Figure B). 2 5. Slip the pre-hinged front door into place by lowering it over the matching hinge on the right side panel (Figure C). Take your time lining up both parts slowly and it will drop into position. Insert hinge pins into hinges. 6. Carefully fit the TOP UNIT down onto the side panels. Be sure to keep the side panels straight while working (Figure D). Attach the top unit with the four remaining screws and washers in the same manner as the side panels. NOTE: At this point the cabinet is assembled. 7. How to hook the weights: Hook the WEIGHTS on the end of the CHAINS located on the bottom inside edge of the top unit. 8. The clock can be aligned and made vertical through adjusting the four feet at the bottom. 3 SETTING UP YOUR CLOCK 1: Carefully remove all packing materials ,tapes, rubber bands, Paper ,etc .From the clock mechanism inside of the TOP UNIT. 2. Hold the pendulum with the bright side of the PENDULUM BOB facing the front of the clock and hang the PENDULUM onto the PENDULUM. CAUTION: The PENDULUM HANGER is suspended from a delicate spring . Do not pull or twist the hanger while hanging the pendulum. Your clock will not run properly and might even stop if the hanger suspension spring is damaged. NOTE: Always remove the pendulum when storing or moving the clock from one place to another and secure the PENDULUM HANGER which a strip of tape so it does not move from side to side. Your clock has been partially wound at the factory. To make sure it is fully wound ,insert the WINDING KEY in to the keyholes and turn in a clockwise direction . The clock is fully wound when you reach a solid stop while turning the key. WIND AS NECESSARY, DO NOT OVER-WIND SETTING THE TIME To set your clock, turn the long {minute } hand only. The hand may turned clockwise or counterclockwise. If you accidentally move the hour hand when setting the clock .Let the clock strike the hour, then carefully turn the hour hand till it points to the hour .Please note that after setting the correct time, the clock may not strike the correct hour the first time . This is normal and the clock will correct itself within the next hour of running. Start the clock running by moving the pendulum to either extreme left or right position and then release .Listen to the sound of the tick-tock {the beat }. The sound should be even and rhythmic. 4 5 ADJUSTMENTS All mechanical clocks require regulation to make them run accurately . Temperature, humidity changes, minor imperfections.in gearing variations in spring torque all affect accuracy .It may take several days to get your clock regulated to the degree of accuracy you desire . DO NOT GET DISCOURAGED, Your clock has been regulated at the factory to be within plus or minutes per day. Do not make any adjustments the first 24 hours .If you have to make an adjustment ,hold the pendulum rod firmly so it does not twist and turn the regulating nut under the pendulum bob to the right to raise the bob and make your clock run faster or to the left to lower the bob and make your clock run slower. One full turn of the adjusting nut sill change the time approximately one minute. When lowering the adjusting nut gently push down on to the bob to make sure it stays against the nut. Walt 24 hours between each adjustment. Once you reach a point where a slight adjustment changes the time from fast to slow or vice versa ,you have reached the maximum accuracy for your time keeping will very slightly as the spring runs down ,you can increase the accuracy of your clock by winding the clock fully every 2 weeks. CARE AND CLEANING OF YOUR CLOCK Clean the glass on your clock periodically as required using a good quality glass cleaner .Spray the cleaner on a soft cloth and wipe the glass .Never spray directly on the glass or click case. Wax and polish the wood portion of clock case as frequently as you do your other fine furniture . Any good furniture polish will do. Your clock movement should be oiled once a year and cleaned every five to ten years depending on climatic conditions. We do not recommend attempting cleaning or olling the movement yourself . Instead, contact a reputable jeweler or clock repair / servicemen. 6 Keep the packing materials and spare way from Children. 7 TROUBLE SHOOTING GUIDE HERE ARE SOME USUAL SYMPOMS THAT ARE ASSOCIATED WITH INCORRECT SET UP AND ARE NOT FAULTS OF THE CLOCK PROBLEM: YOUR CLOCK IS QUIET SOLUTION: 1.CHECK YOUR CLOCK HAS NOT BEEN WINDED. 2.CHECK PROTECTING GONG CARDBOARD HAS NOT BEEN TAKEN OUT. PROBLEM:YOUR CLOCK PENDULUM WILL NOT SWING SOLUTION:1.CHECK YOUR CLOCK HAS NOT BEEN SITTING ON A PLAIN GROUND. 2.CHECK YOUR CLOCK HAS NOT BEEN WINDED. 3.SOMETIMES, ENOUGH FULL WINDING ALSO MAKING NOT SWING , PLEASE TAKE OFF THE PENDULUM, AFTER SEVERAL MINUTES, PUT THE PENDULUM ON. PROBLEM: YOUR CLOCK GOES FASTER SOLUTION:THERE IS A SCREW ON THE BOTTOM OF THE PENDULUM BOB,SCREW THE BOB A LITTLE DOWN. REMEMBER: ONE CIRCLE OF SCREW IS SLOWER 30 SECONDS. PROBLEM: YOUR CLOCK GOES SLOWER SOLUTION: THERE IS A SCREW ON THE BOTTOM OF THE PENDULUM BOB. SCREW THE BOB A LITTL UP . REMEMBER: ONE CIRCLE OF SCREW IS FASTER 30 SECONDS. PROBLEM: YOUR CLOCK CHIMES IS NOT CORRECT SOLUTION: FINGER MAKES THE HOUR HAND TO THE CORRECT CHIME, THEN TRY. PROBLEM: IF YOUR CLOCK CHIMES EXCEEDING +15 MINUTES (-15MINUTES) SOLUTION: TAKE OUT THE MINUTE HAND AND ASSEMBLING THE MINUTE HANDS AGAIN. 8 ATTENTION: In order to ensure that your clock is stable, adjust the levelers under the clock. As an added safety feature, a support strap has been provided and is fixed to the top of the clock. It recommended that you attach the clock to the wall using this strap as shown below. Take note of the wall mounting guide on the following pages. 9 A Guide to Wall Mounting & Fixings Important note: Important: Make sure that the screws and wall plugs being used are suitable for supporting your unit.Consult a qualified tradesperson if you are unsure. Hints: Always use a larger screw and wall plug -these are only suitable for if you are not sure. use in masonry walls. 2: Ensure you use the recommended drill bit to match the wall plug and hole size. If you are in any doubt about 3: Ensure you drill the hole horizontally,do not force the drill or the correct wall plugs for Enlarge the hole. your wall,seek professional 4: Take extra care when drilling high walls, ceilings and ceramic advice. tiles.Ensure wall plugs are inserted beyond the thickness of the ceramic tiles to avoid the tiles splitting or cracking. Failure of the product due 5: Ensure wall plugs are well fitted and are a tight fit in the tousing incorrect fixings is the responsibility of the installer. drilled hole. Types of walls You can use one of the following types of wall plug if your walls are madeof brick, breeze block,concrete,stone or wood. Generally aerated blocks should not For use wich plasterboard partitions or For use with walls stuck with be used to support heavy loads,use Hollow wooden doors. Plasterboard,The hammer fixing allows it to be fixed to the wall rather than the a specialist fitting in this case,For light plasterboard.Always check the fixing loads,general purpose wall plugs can is secure to the retaining wall. be used. For use when attaching light loads on For use when attaching light loads on For use with heavier loads such as TV to plasterboard partitions to plasterboard partitions & HiFi speakers and satellite dishes etc.
Recommended publications
  • Grandfathers' Clocks: Their Making and Their Makers in Lancaster County
    GRANDFATHERS' CLOCKS: THEIR MAKING AND THEIR MAKERS IN LANCASTER COUNTY, Whilst Lancaster county is not the first or only home of the so-called "Grandfathers' Clock," yet the extent and the excellence of the clock industry in this type of clocks entitle our county to claim special distinction as one of the most noted centres of its production. I, therefore, feel the story of it specially worthy of an enduring place in our annals, and it is with pleasure •and patriotic enthusiasm that I devote the time and research necessary to do justice to the subject that so closely touches the dearest traditions of our old county's social life and surroundings. These old clocks, first bought and used by the forefathers of many of us, have stood for a century or more in hundreds of our homes, faithfully and tirelessly marking the flight of time, in annual succession, for four genera- tions of our sires from the cradle to the grave. Well do they recall to memory and imagination the joys and sorrows, the hopes and disappointments, the successes and failures, the ioves and the hates, hours of anguish, thrills of happiness and pleasure, that have gone into and went to make up the lives of the lines of humanity that have scanned their faces to know and note the minutes and the hours that have made the years of each succeeding life. There is a strong human element in the existence of all such clocks, and that human appeal to our thoughts and memories is doubly intensified when we know that we are looking upon a clock that has thus spanned the lives of our very own flesh and blood from the beginning.
    [Show full text]
  • Grandfathers' Clocks: Their Making and Their Makers in Lancaster County *
    Grandfathers' Clocks: Their Making and Their Makers in Lancaster County * By D. F. MAGEE, ESQ. Whilst Lancaster County is not the first or only home of the so-called "Grandfathers' Clock," yet the extent and the excellence of the clock industry in this type of clocks entitle our county to claim special distinction as one of the most noted centres of its production. I, therefore, feel the story of it specially worthy of an enduring place in our annals, and it is with pleasure and patriotic enthusiasm that I devote the time and research necessary to do justice to the subject that so closely touches the dearest traditions of our old county's social life and surroundings. These old clocks, first bought and used by the forefathers of many of us, have stood for a century or more in hundreds of our homes, faithfully and tirelessly marking the flight of time, in annual succession for four genera- tions of our sires from the cradle to the grave. Well do they recall to memory and imagination the joys and sorrows, the hopes and disappointments, the successes and failures, the loves and the * A second edition of this paper was necessitated by an increasing demand for the pamphlet, long gone from the files of the Historical Society. No at- tempt has been made to re-edit the text. D. F. Magee's sentences, punctuations and all are his own. A few errors of dates or spelling have been corrected, and a few additions have been made. These include the makers, Christian Huber, Henry L.
    [Show full text]
  • Using a Grandfather Pendulum Clock to Measure the World's Shortest
    Journal of Applied Mathematics and Physics, 2021, 9, 1076-1088 https://www.scirp.org/journal/jamp ISSN Online: 2327-4379 ISSN Print: 2327-4352 Using a Grandfather Pendulum Clock to Measure the World’s Shortest Time Interval, the Planck Time (With Zero Knowledge of G) Espen Gaarder Haug Norwegian University of Life Sciences, Ås, Norway How to cite this paper: Haug, E.G. (2021) Abstract Using a Grandfather Pendulum Clock to Measure the World’s Shortest Time Inter- Haug has recently introduced a new theory of unified quantum gravity coined val, the Planck Time (With Zero Know- “Collision Space-Time”. From this new and deeper understanding of mass, we ledge of G). Journal of Applied Mathemat- can also understand how a grandfather pendulum clock can be used to meas- ics and Physics, 9, 1076-1088. ure the world’s shortest time interval, namely the Planck time, indirectly, https://doi.org/10.4236/jamp.2021.95074 without any knowledge of G. Therefore, such a clock can also be used to Received: April 24, 2021 measure the diameter of an indivisible particle indirectly. Further, such a clock Accepted: May 24, 2021 can easily measure the Schwarzschild radius of the gravity object and what we Published: May 27, 2021 will call “Schwarzschild time”. These facts basically prove that the Newton Copyright © 2021 by author(s) and gravitational constant is not needed to find the Planck length or the Planck Scientific Research Publishing Inc. time; it is also not needed to find the Schwarzschild radius. Unfortunately, This work is licensed under the Creative there is significant inertia towards new ideas that could significantly alter our Commons Attribution International perspective on the fundamentals in the current physics establishment.
    [Show full text]
  • Celestial, Flow, and Mechanical Clocks
    recalibration Michael A. Lombardi First in a Series on the Evolution of Time Measurement: Celestial, Flow, and Mechanical Clocks ime is elusive. We are comfortable with the concept of us are many centuries older than the first clocks. The first -in time, but in many ways it defies understanding. We struments that we now recognize as clocks could measure T cannot see, hear, or touch time; we can only observe intervals shorter than one day by dividing the day into smaller its effects. Although we are unable to grasp time with our tra- parts. ditional senses, we can clearly “feel” the passage of time as we Most historians credit the Egyptians with being the first civ- watch night turn to day, the seasons change, or a child grow up. ilization to use clocks. Their first clocks were probably nothing We are also aware that we can’t stop or reverse the continuous more than sticks placed in the ground that indicated time by flow of time, a fact that becomes more obvious as we get older. both the length and direction of their shadow. As early as 1500 Defining time seems impossible, and attempts to do so by phi- BC, the Egyptians had developed a more advanced shadow losophers and scientists fall far short of their goal. clock (Fig. 1). This T-shaped instrument was placed in a sun- In spite of its elusiveness, we can measure time exception- lit area on the ground. In the morning, the crosspiece (AA) was ally well. In fact, we can measure time with more resolution set to face east and then rotated in the afternoon to face west.
    [Show full text]
  • The Bytown Times
    The Bytown Times VOLUME 40 NO. 1 JANUARY 26, 2020 ISSN 1712—2799 Celebrating 40 Years of The Bytown Times!! (See the story on Page 6) NOVEMBER MEETING HIGHLIGHTS INSIDE THIS ISSUE November Meeting Highlights 1-3 Forty-five members and guests attended the Ottawa Valley Watch and Clock Club November meeting at the Pinecrest November Meeting Photos 4 Recreation Centre. Annual Wine and Cheese Social 5 Feature Presentation 40 Years of The Bytown Times 6-7 Our feature presentation, “Colchester Clock and Watch Makers 1710-1850” was given by Robert St-Louis. As we Annual Trash & Treasure Auction 7 have come to expect from Robert, his presentation was thor- Did You Know? 7 oughly researched and well presented with numerous slides. Robert started with a brief history of watch and clock making Clock Museum News 8-10 in England and in particular the evolution of the trade in Fabulous Finds 11-12 “provincial” centres such as Colchester—50 miles from Lon- don. He went on to describe one of his key sources for infor- Grandfather Clock for Sale 12 mation, the book “Clock and Watchmaking in Colchester” by Editor and President’s Corners 12 Bernard Mason. To illustrate his talk, Rob- ert focused his research on the fascinating story of six horologists who oper- ated between the 17th and 19th centuries. The six horologists were all linked over time as each took over the business of his predecessor. (One only apprenticed to the busi- ness and didn’t take it A Timeline of the Colchester over.) The six were: Jere- Clock and Watchmakers my Spurgin, John Smorth- wait, William Cooper, Nathaniel Hedge 3, Nathaniel Hedge 4, and Joseph Bannister.
    [Show full text]
  • A Biography of the Second
    A BIOGRAPHY OF THE SECOND By Jessica Hendrickson B.A. Natural Sciences Hampshire College, 2006 SUBMITTED TO THE PROGRAM IN COMPARATIVE MEDIA STUDIES/WRITING IN PARTIAL FULFILLMENT OF THE REQUIREMENTS FOR THE DEGREE OF MASTER OF SCIENCE IN SCIENCE WRITING AT THE MASSACHUSETTS INSTITUTE OF TECHNOLOGY SEPTEMBER 2020 © 2020 Jessica Hendrickson. All rights reserved. The author hereby grants to MIT permission to reproduce and to distribute publicly paper and electronic copies of this thesis document in whole or in part in any medium now known or hereafter created Signature of Author: ____________________________________________________________ Jessica Hendrickson Department of Comparative Media Studies/Writing August 7, 2020 Certified by: __________________________________________________________________ Tom Levenson Department of Comparative Media Studies/Writing Thesis Advisor Accepted by: _________________________________________________________________ Alan Lightman Department of Comparative Media Studies/Writing Graduate Program of Science Writing Director A BIOGRAPHY OF THE SECOND By Jessica Hendrickson Submitted to the Program in Comparative Media Studies/Writing on August 7, 2020 in partial fulfillment of the requirements for the degree of Master of Science in Science Writing ABSTRACT A few blinks of an eye. The time it takes a hummingbird to flap its wings 80 times. For a photon of light to travel from Los Angeles to New York and back almost 40-fold. The second has been there since the literal dawn of time, if one exists. But what defines the second? Like a pop star constantly reinventing themselves, the second has undertaken a myriad of identities, first defined as a brief moment in the daily rotation of the earth around its axis. Today, the second is officially defined by over 9 billion oscillations of a cesium atom.
    [Show full text]
  • 13Oscillations and Waves
    Oscillations and Waves 13Inside • 13.1 Oscillations and Periodic Motion 453 • 13.2 The Pendulum 462 • 13.3 Waves and Wave Properties 470 • 13.4 Interacting Waves 476 Though she may not be thinking about it, this girl is demonstrating the basic physics of oscillatory motion. In Chapter 8 you studied objects that are at rest. Such objects are seldom Big Idea left undisturbed for very long, it seems. Soon they are disturbed by a bump, Waves are traveling a kick, or a nudge. When this happens, you may see a series of back-and- oscillations that forth motions referred to as oscillations. The properties of oscillations are carry energy. explored in this chapter. You will also learn that oscillations can produce waves, a topic of central importance in physics. This chapter introduces you to the properties of waves and explains how waves interact with one another. WALK1156_01_C13_pp452-491.indd 452 12/14/12 4:39 PM Inquiry Lab How do waves move in water? Explore 3. Repeat Step 2, this time dipping which direction does the wave the pencil into the water more that forms move? What happens 1. Fill a rectangular pan half full forcefully, but not so hard as to when the wave hits the end of of water. make a splash. the pan? 2. Hold a pencil horizontally be- 4. Repeat Step 2, this time continual- 2. Assess Did anything affect the tween your thumb and forefin- ly dipping the pencil in the water height of the wave or its speed? ger. Gently dip the pencil into about once per second for 10 s.
    [Show full text]
  • 1.1 John Harrison
    Name: ___________________________________________ Mapping the Earth Date: __________________________ Period: ___________ The Physical Setting: Earth Science Supplemental: John Harrison Biography John Harrison Biography Nancy Giges - www.asme.org John Harrison (1693 – 1776), English inventor and clockmaker over- came one of the most challenging problems of the 18th century: how to determine the longitude of a ship at sea, saving many lives. In so doing, he had to defy the establishment, fight to collect a huge prize offered by Parliament, and wait for decades before receiving the recognition he deserved. Biographers say Harrison's fascination with watches, clocks, and other timepieces can be traced to age six when he was sick with smallpox, and he entertained himself with a watch his parents placed on his pil- low. Watches in those days were very large, and while not very accu- rate, their works were visible and one could see a relationship between the loud ticking and the watch's mechanical action. Although a carpenter by trade, Harrison's father occasionally repaired clocks, and young John assisted his father in his work as soon as he was old enough. As he grew older, Harrison combined his interest in woodworking and timepieces to begin building clocks and completed his first longcase clock, more commonly called a grandfather clock, in 1713 at the age of 20. It was just a year later that Parliament offered a prize of 20,000 pounds to calculate a ship's precise longitude at sea. Harrison decided to go for it. Sailors knew the principle of calculating longitude: that for every 15 degrees travelled eastward, the local time moved forward one hour.
    [Show full text]
  • 7: Geodesy for Tectonic Studies
    7: GEODESY FOR TECTONIC STUDIES Geodesy is the science of the earth’s shape Find precise positions Monitor changes due to tectonic processes: Plate motion Plate boundary deformation Intraplate deformation Earthquake cycle Volcanic processes Land Subsidence Etc Topic 7 1 TECTONIC GEODESY Determine positions of geodetic monuments and monitor how positions change over time Until recently, measurements made by triangulation, which measures angles between monuments using a theodelite, or trilateration, which measures distances with a laser. Vertical motion measured by leveling, using a precise level to sight on a measuring rod. Space geodesy measures all Davidson et al, 2002 three components of position to sub-centimeter precision. Space-based is cheaper, easier, faster, and does not require sites to be visible from each other Topic 7 2 SPACE-BASED GEODESY USE EXTRATERRESTRIAL SOURCES TO MEASURE POSITIONS ON THE EARTH SIZE OF THE EARTH (Eratosthenes 200 BC) At the summer solstice the sun shone directly into a well at Syene, Egypt at noon. At the same time, in Alexandria, approximately 805 km due north of Syene (now Aswan), the angle of inclination of the http://advancedmathyoungstudents.com/ sun's rays was about 7.2. With these measurements he computed the radius and circumference of the earth. 7.2 / 360 = 805 / (2 ! radius ) Topic 7 3 VLBI - VERY LONG BASELINE RADIO INTERFEROMETRY ("Very Large Bunch of Investigators") Radio signals from quasars (astronomical radio sources which are the most distant objects in the universe) arrive at different
    [Show full text]
  • How to Prepare Your Grandfather Clock for a Move
    How to Prepare Your Grandfather Clock for a Move Follow these easy steps and you are on your way to moving your Grandfather clock. Always start with the weights down about 3 - 4 days of movement. 1. Open the side access window (if any) and move them to a safe place where you may not step on one and break it. 2. If the clock has cable holding the weights, insert 3 - 2" square Styrofoam blocks above each pulley between the cables. If you do not have a Styrofoam block, make a tight square of newspaper about 2" inches in diameter and hold the block or newspaper square above the pulley as you wind the weights one at a time until they stop with the paper or Styrofoam block jammed above the pulleys. This procedure prevents the cable from tangling when the weights are removed. You need to keep tension on the cables. 3. For clocks with chains, raise the weights so the clock is about half wound (middle of the clock). Use a piece of thin wire or twist ties to string the chains together just where the chains protrude below the movement and tie the wire together; this action will secure the chains so they do not come off their sprockets. These need to be tight or the chain will come off the sprocket. 4. Remove the weights while wearing gloves and look at the bottom to see if they are marked "Left - Center - Right" . If not, mark them so they can be replaced to the same position on the clock for installation later.
    [Show full text]
  • What's It Worth?
    WHAT’S IT WORTH? Price Guide to Clocks 2014 Clocks Magazine Horology Guides No 4 What’s it worth? Price Guide to Clocks 2014 Clocks Magazine Horology Guides No 4 Published by Splat Publishing Ltd 141b Lower Granton Road Edinburgh EH5 1EX United Kingdom www.clocksmagazine.com CONTENTS Introduction 7 Valuing clocks 9 Grandfather clocks 10 Bracket and mantel clocks 25 Wall clocks 77 © 2013 Clocks Magazine World copyright reserved Skeleton clocks 90 Mystery and novelty clocks 97 Regulators and chronometers 109 Electric clocks 117 Unusual clocks and barographs 123 ISBN: 978-0-9562732-3-9 Glossary of Common Clock Terms 127 The right of Clocks Magazine to be identified as author of this work has been asserted in accordance with the Copyright, Designs and Patents Act 1988. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means electronic, mechanical, photocopying, recording or otherwise, without the prior permission of the publisher. Printed by CBF Cheltenham Business Forms Ltd, 67 Hatherley Road, Cheltenham GL51 6EG Int R O DU ction CL oc K S MAGAZ ine HO R O L O GY GU I D es No 1. Clock Repair, A Beginner’s Guide There are two big differences between No 2. A Beginner’s Guide to Pocket Watches clocks and most other types of antique. No 3. American Clocks, An Introduction First, clocks are machines. They sit in No 4. What’s it Worth? Price Guide to Clocks 2014 the corner or on the mantelshelf or on the wall, doing something.
    [Show full text]
  • Buyer's Guide for Grandfather Clocks
    10 Things You Should Know About Grandfather Clocks Before You Buy. Learn How to Buy a Clock Like a Grandfather Clock Maker Would! BUYER’S GUIDE FOR GRANDFATHER CLOCKS Courtesy of 3609 49th Street North in Disston Plaza 727.525.5771 10 Things You Should Know about Grandfather Clocks Before You Buy “Owning a grandfather clock is a wonderful life-changing addition that you, your family and their heirs will enjoy for generations. The calm, soothing sense of peacefulness or well-being from the steady ‘tick tock’ is a welcome sound in a world of never ending change.” -- , #1 ~ Location, location, location. Where you display your new clock will make a difference in what you buy and the enjoyment you get from owning a grandfather clock. • Is your home large with high ceilings? • Do you have a staircase with a wide landing? • Do you collect valuables that might be placed on the adjustable shelves for a curio-style clock? Deciding on the best place for your new clock will be a major factor in the size and style you select. A little planning will guarantee that you’ve madeMark the right decision.Boggs 1. Treat your clock like a fine piece of furniture. You can either place it next to a china cabinet or wall case, or all by itself on a short wall where it stands out. 2. Corner locations often allow viewing from anywhere in a room and can help fill in an awkward space that often goes unfurnished. 3. Entryway locations make an opening statement and allow for added wall interest as long as your clock is clear of foot traffic.
    [Show full text]