2020 Instructions
Total Page:16
File Type:pdf, Size:1020Kb
www.collegehillshonda.com Accessory Application Publications No. INSTALLATION VERSION 1 ARMREST ILLUMINATION 2020 CIVIC Issue Date INSTRUCTIONS AUG 2019 PARTS LIST 2 Urethane tapes Armrest Illumination Kit P/N 08E16-TBA-100A P/N 08E16-TBA-100B Left light (Identification mark: L) 4 Aluminum tapes Right light (Identification mark: R) Relay Light harness Clip 14 Wire ties Wire tie with holder Fuse label Unit © 2019 American Honda Motor Co., Inc. – All Rights Reserved. AII11806-03 (1907) 08E16-TBA-1000-9A 1 of 23 www.collegehillshonda.com Console Armrest Kit TOOLS AND SUPPLIES REQUIRED P/N 08U89-TXM-100 Phillips screwdriver Console center armrest Ratchet 10 mm Socket 10 mm Open end wrench Diagonal cutters Masking tape Ruler Left console side armrest Isopropyl alcohol Shop towel Scissors Blanket Hacksaw File Right console side armrest The following tools are available through the Honda Tool and Equipment Program. On the iN, click on Service > Service Bay > Tool and Equipment Program, then enter the number under “Search.” Or, call 888-424-6857. • Plastic Trim Tool (T/N SILTRIMTL10) • Trim Tool Set (T/N SOJATP2014) Illustration of the Armrest Illumination Installed in the Accessory user’s information manual Vehicle CONSOLE CENTER 2A FUSE ARMREST RIGHT CONSOLE SIDE ARMREST RIGHT LIGHT RELAY LIGHT LEFT LIGHT HARNESS UNIT LEFT CONSOLE SIDE ARMREST 2 of 23 AII11806-03 (1907) © 2019 American Honda Motor Co., Inc. – All Rights Reserved. www.collegehillshonda.com INSTALLATION Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.” 4 CLIPS 1. Disconnect the negative cable from the battery. 2. Remove the passenger’s dashboard side lid, and unplug the vehicle connector, if equipped. Pull away the door opening seal. DOOR OPENING SEAL 3 RETAINING (Pull away.) TABS PASSENGER’S UNDER COVER 4. Open the glove box, push inward on the glove box stops and remove the glove box. 2 GLOVE BOX STOPS VEHICLE CONNECTOR PASSENGER’S (if equipped) DASHBOARD 4 CLIPS SIDE LID 3. Remove the passenger’s under cover. GLOVE BOX © 2019 American Honda Motor Co., Inc. – All Rights Reserved. AII11806-03 (1907) 3 of 23 www.collegehillshonda.com 5. Remove the glove box cover, and unplug the vehicle 6. Remove the driver’s dashboard lower cover, unplug connector, if equipped. the vehicle connectors and aspirator hose. VEHICLE VEHICLE 4 SELF-TAPPING CONNECTOR ASPIRATOR HOSE CONNECTOR 4 CLIPS SCREWS (if equipped) 2 CLIPS VEHICLE CONNECTORS 2 CLIPS 2 CLIPS 2 BOLTS GLOVE BOX COVER DRIVER’S DASHBOARD 5 CLIPS LOWER COVER DIFFERENTLY SHAPED GLOVE BOX COVER 7. Remove the left console armrest. LEFT CONSOLE 4 CLIPS ARMREST (Do not reuse.) 4 of 23 AII11806-03 (1907) © 2019 American Honda Motor Co., Inc. – All Rights Reserved. www.collegehillshonda.com 8. Attach masking tape to the area shown. 10. Remove the right console armrest. AUDIO UNIT RIGHT CONSOLE MASKING TAPE 4 CLIPS ARMREST (Do not reuse.) LEFT CENTER CONSOLE TRIM 11. Attach masking tape to the area shown. 9. Remove the left center console trim. AUDIO UNIT MASKING TAPE 4 CLIPS RIGHT CENTER LEFT CENTER CONSOLE TRIM CONSOLE TRIM © 2019 American Honda Motor Co., Inc. – All Rights Reserved. AII11806-03 (1907) 5 of 23 www.collegehillshonda.com 12. Remove the right center console trim. 14. Remove the audio unit, and unplug the vehicle connectors. 6 CLIPS AUDIO UNIT 4 CLIPS RIGHT CENTER CONSOLE TRIM 13. Remove the A/C control unit, and unplug the vehicle connectors. 2 BOLTS VEHICLE CONNECTORS 2 RETAINING 4 CLIPS TABS VEHICLE VEHICLE BRACKET CLIP 15. Remove the console rear panel and unplug the vehicle connectors, if equipped. VEHICLE CONNECTORS (if equipped) A/C CONTROL VEHICLE UNIT CONNECTORS CONSOLE 4 CLIPS REAR PANEL 6 of 23 AII11806-03 (1907) © 2019 American Honda Motor Co., Inc. – All Rights Reserved. www.collegehillshonda.com 16. Remove the shift lever console panel: • Remove the console panel, and unplug the vehicle connectors. A/T Models • Open the center console armrest, and slide the CONSOLE sliding tray (if equipped) and the beverage PANEL 2 SELF-TAPPING holder rearward. SCREWS • Remove the shift lock release cover with a plastic trim tool. • Insert the key into the shift lock release slot, and move the shift lever knob to the D position. NOTE: Make sure to apply the parking brake. SHIFT LOCK RELEASE SHIFT LOCK SLOT RELEASE COVER SHIFT LEVER KNOB (Move to the D position.) KEY 5 CLIPS VEHICLE CONNECTORS • Release the shift lever panel. SHIFT LEVER PANEL 4 CLIPS CENTER CONSOLE ARMREST SLIDING TRAY BEVERAGE (if equipped) HOLDER © 2019 American Honda Motor Co., Inc. – All Rights Reserved. AII11806-03 (1907) 7 of 23 www.collegehillshonda.com M/T Models 17. Remove the upper tray mat. • Lower the shift lever boot to release two retaining tabs from the boot. • Remove the shift lever knob. SHIFT LEVER KNOB UPPER TRAY MAT 2 RETAINING TABS SHIFT LEVER BOOT 5 CLIPS RETAINING TAB 18. Remove the console panel. • Remove the shift lever panel, and unplug the vehicle connectors. SHIFT LEVER PANEL 2 SELF-TAPPING SCREWS 2 SELF- TAPPING SCREWS CONSOLE PANEL BOLT 5 CLIPS VEHICLE CONNECTORS 8 of 23 AII11806-03 (1907) © 2019 American Honda Motor Co., Inc. – All Rights Reserved. www.collegehillshonda.com 19. If equipped, remove the lower tray mat. 21. If equipped, release the vehicle clip, and unplug the vehicle connector. VEHICLE VEHICLE CONNECTOR CLIP (if equipped) (if equipped) LOWER TRAY MAT (if equipped) 2 RETAINING TABS 20. Using a plastic trim tool, remove the switch panel, and unplug the vehicle connectors. VEHICLE CONNECTORS 6 CLIPS LOWER TRAY SWITCH 22. Remove the lower tray. PANEL 3 CLIPS RETAINING TAB PLASTIC TRIM TOOL CUTOUT © 2019 American Honda Motor Co., Inc. – All Rights Reserved. AII11806-03 (1907) 9 of 23 www.collegehillshonda.com 23. Remove the left side panel. 25. Remove the dashboard center lower cover. VEHICLE CLIP 2 CLIPS 2 SELF- TAPPING VEHICLE SCREWS CLIP LEFT SIDE PANEL 3 BOLTS DASHBOARD CLIP CENTER LOWER COVER CLIP 5 SELF-TAPPING SCREWS 26. Remove the two self-tapping screws from the center console armrest. 24. Remove the right side panel. CENTER VEHICLE CLIP CONSOLE ARMREST RIGHT SIDE PANEL 2 SELF- TAPPING SCREWS 5 SELF-TAPPING CLIP SCREWS 10 of 23 AII11806-03 (1907) © 2019 American Honda Motor Co., Inc. – All Rights Reserved. www.collegehillshonda.com 27. Remove the center console armrest. 28. Apply masking tape to the left side panel as shown. CENTER CONSOLE ARMREST 5 mm 2 RETAINING (Do not reuse.) 2 CLIPS (0.20 in.) TABS 15 mm (0.59 in.) Cut. MASKING TAPE LEFT SIDE PANEL CENTER ARMREST BASE CORRECT INCORRECT HACKSAW HACKSAW LEFT SIDE LEFT SIDE PANEL PANEL SECTION VIEW 29. Using a hacksaw, cut the left side panel as shown. Using a file, remove any burrs. NOTE: Be careful not to damage the left side panel. 30. Remove the masking tape. 31. Repeat steps 28 through 30 on the other side. © 2019 American Honda Motor Co., Inc. – All Rights Reserved. AII11806-03 (1907) 11 of 23 www.collegehillshonda.com 32. Apply masking tape to the left light harness as 33. Using isopropyl alcohol on a shop towel, thoroughly shown. clean the left side panel where the aluminum tape NOTE: Make sure to check the identification mark of will attach. the left light. 40 mm 60 mm (1.57 in.) (2.36 in.) WIRE TIE 60 mm (2.36 in.) LEFT LIGHT (Identification mark: L) 270 mm (10.63 in.) ALUMINUM TAPE (Cut in two.) LEFT LIGHT HARNESS 90 mm MASKING TAPE LEFT LIGHT (3.54 in.) (Line up with HARNESS the curved end.) Clean with isopropyl alcohol. MASKING TAPE LEFT LIGHT 2-PIN CONNECTOR LEFT 40 mm SIDE PANEL (1.57 in.) (inside) RIB MASKING TAPE (Line up with the end of the rib.) Clean with isopropyl alcohol. 34. Using scissors, cut one piece of aluminum tape as shown. Secure the left light harness to the left side panel with two pieces of aluminum tape. 12 of 23 AII11806-03 (1907) © 2019 American Honda Motor Co., Inc. – All Rights Reserved. www.collegehillshonda.com 35. Using isopropyl alcohol on a shop towel, thoroughly 38. Using isopropyl alcohol on a shop towel, thoroughly clean the left side panel where the aluminum tape clean the fuse case where the fuse label will attach. will attach. FUSE CASE 40 mm 60 mm (Clean with isopropyl alcohol.) (1.57 in.) (2.36 in.) ALUMINUM TAPE FUSE LABEL (Cut in two.) (2A OPTION FUSE) LEFT SIDE PANEL LEFT LIGHT LIGHT HARNESS HARNESS 39. Apply the fuse label to the light harness fuse case. 60 mm (2.36 in.) RIB 40 mm (1.57 in.) Clean with isopropyl alcohol. 36. Using scissors, cut one piece of aluminum tape as shown. Secure the left light harness to the left side panel with two pieces of aluminum tape. NOTE: Do not fold the left light harness. 37. Repeat steps 32 through 36 to install the right light to the right side panel. © 2019 American Honda Motor Co., Inc. – All Rights Reserved. AII11806-03 (1907) 13 of 23 www.collegehillshonda.com 40. Route the light harness as shown. 41. Line up the green tape on the light harness with the vehicle clip, and secure the light harness to the LIGHT HARNESS vehicle harness with one wire tie. 6-PIN CONNECTOR WIRE TIE VEHICLE VEHICLE CLIP HARNESS LIGHT HARNESS 12-PIN CONNECTOR LIGHT HARNESS 2-PIN CONNECTOR VEHICLE LIGHT GREEN TAPE PANEL HARNESS (Line up with the vehicle clip.) LIGHT HARNESS 42. Plug the vehicle or other accessory 12-pin connector into the light harness 12-pin connector.