DOCSLIB.ORG

VRX-SL Sales Brochure

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
VRX-SL Sales Brochure Radio Systems VRX-SL Single Channel VHF Receiver Specifications Frequency To be specified within 136-174MHz Modulation Narrowband FM 12.5kHz or 25kHz channel spacing to be specified at time of order Sensitivity 107dBm (luV) signal modulated by 1kHz tone with a peak deviation of 2.5kHz produces an output s+n/n ratio greater than 26dB Squelch Threshold 120dB (0,2uV) nominal. Adjustable through control under battery cover Adjacent Channel Rejection Ratio Better than 75dB Spurious Response Better than 60dB Intermodulation Rejection Ratio Better than 60dB, measured as per MPT 1301 Desensitisation (Blocking) Level Better than -23dBm Spurious Outputs Excellent RF performance Less than -47dBm (20nW) Outputs Recorder-50mV rms (typical) into 20KO, Small size suitable both for discreet body-worn independent of volume setting communication and general portable applications Headphones-60mW typical into 8Q. Squelch-open collector/-ve ground. 'On' when receiver is muted Supply Voltage Outputs for headphones, recorder and squelch state 6-10VDC. Power Source Internal PP3 Alkaline battery. Simple interfacing for control of other equipment Rear panels with power input socket available. Battery Life Available with factory fitted scrambler With squelch lifted and standard headphones connected approximately 12 hours Supply Current The VRX-SL receiver, due to its small size, is generally intended for body- Less than 25mA with squelch lifted and no worn use. However, the receiver's excellent performance and facilities headphones. make it suitable for other portable applications. Temperature Range Above specifications measured between + 10°C to +35°C. Permissible operating Outputs temperature range-10°C to +60°C A single socket provides outputs for ear/headphones (including Front Panel Control inductive earpieces), tape recorder and squelch state. The squelch Single 6-position switch for off, output allows control of other equipment. A VTX transmitter and VRX-SL battery test, and 4 volume settings receiver can be connected together to form an automatic repeater or Front Panel Indicator remotely controlled transmitter. Directly compatible with TTL level Single LED for battery test inputs the addition of the Audiotel Receiver Interface Unit, which uses Rear Control the receiver's squelch output to drive a relay, enables a standard tape (Under battery cover). Squelch threshold recorder, for example, to be activated whenever the receiver detects Finish Black. Other colours to special order Tel: 0536 66677 Fax: 0536 66711 ^w#a#i#tLi Telex: 341775 AudintG Audiotel International Limited, Cavendish Courtyard, Sallow Road, Corby, England NN17 1DZ § Copyright 1989 Audiotel International. All rights reserved. All specifications, through product improvement, may be changed without notice. an on-channel transmission. Combined with a VTX transmitter Size & Weight operating in the voice activated (VOX) mode this gives great flexibility Width 64mm for unattended operation. Depth 23mm Height 113mm (inc connectors) Weight including battery 245g The audio output, adjustable to 4 volume settings, allows a wide range Accessories of earpieces and headphones together with small loudspeakers to be Included with every unit is a pair of driven, The tape recorder output level is independent of this setting, walkman style earphones and a soft wire an tenna. Other options include: RF Performance Headphones, earphones, and inductive Sensitivity, unwanted signal rejection and desensitisation performance earpieces Multi-output lead assemblies are excellent for such a compact and low power receiver. Using noise Interface for switching of tape recorders and detection as opposed to carrier detection ensures that the squelch is other equipment reliable, repeatable and immune to false operation. Vehicle antennas and adaptors Vehicle power supply A control beneath the battery cover enables the squelch level to be Mains power supply Body harness adjusted. Internal power regulation gives constant performance as the Related Equipment battery discharges. Power consumption is low and continuous VTX transmitters operation for over 24 hours is possible with a fresh Alkaline battery. VRX multichannel receiver Slow speed cascadable cassette recording Construction systems An extruded aluminium sleeve forms the main chassis and gives good VRXS scrambled receiver mechanical strength. All circuitry is contained on a single board VTX/VRX AC PSU VTX/VRX Vehicle PSU allowing access to all components. Self-latching connectors and 4 digit DTMF Switch for remote control switched rotary control help eliminate accidental operation and disabling. Order Numbers 601-200 VRX-SL 12.5kHz single channel receiver 601-201 VRX-SL 25.0kHz single channel receiver 601 -300 VRXS-SL 12.5kHz receiver with fitted scrambler 601-301 VRXS-SL 25.0kHz receiver with fitted scrambler VRXS-SL Dimensions 5jl (showing scrambler fitted) p ® ® Output Socket I [LED I \Antenna socket | ® ® 99mm Headphones Ae/-ve Squelch/Remote Recorder "1 ' lopnm ® ® 7 •64mm- 23mm .® o ps ® 7 Sauelch --TV+ Battetv 23mm ■ 64mm ■ Poortweg 6,2612 PA Delft, Tel: 015-614041. Fax: 015-623577 Audiotel International Limited, Cavendish Courtyard, Sallow Road, Corby, England NN17 1DZ _> Copyright 1989 Audiotel International. All rights reserved. All specifications, through product improvement, may be changed without notice..
Load more

Recommended publications
  • How to Tape-Record Primate Vocalisations Version June 2001
    How To Tape-Record Primate Vocalisations Version June 2001 Thomas Geissmann Institute of Zoology, Tierärztliche Hochschule Hannover, D-30559 Hannover, Germany E-mail: [email protected] Key Words: Sound, vocalisation, song, call, tape-recorder, microphone Clarence R. Carpenter at Doi Dao (north of Chiengmai, Thailand) in 1937, with the parabolic reflector which was used for making the first sound- recordings of wild gibbons (from Carpenter, 1940, p. 26). Introduction Ornithologists have been exploring the possibilities and the methodology of tape- recording and archiving animal sounds for many decades. Primatologists, however, have only recently become aware that tape-recordings of primate sound may be just as valuable as traditional scientific specimens such as skins or skeletons, and should be preserved for posterity. Audio recordings should be fully documented, archived and curated to ensure proper care and accessibility. As natural populations disappear, sound archives will become increasingly important. This is an introductory text on how to tape-record primate vocalisations. It provides some information on the advantages and disadvantages of various types of equipment, and gives some tips for better recordings of primate vocalizations, both in the field and in the zoo. Ornithologists studying bird sound have to deal with very similar problems, and their introductory texts are recommended for further study (e.g. Budney & Grotke 1997; © Thomas Geissmann Geissmann: How to Tape-Record Primate Vocalisations 2 Kroodsman et al. 1996). For further information see also the websites listed at the end of this article. As a rule, prices for sound equipment go up over the years. Prices for equipment discussed below are in US$ and should only be used as very rough estimates.
    [Show full text]
  • Instruction Manual
    N A G R A 4.2 PORTABLE ANALOGUE AUDIO TAPE RECORDER INSTRUCTION MANUAL (KSA code No. 20 04 004 151) Kudelski S.A. NAGRA Tape Recorder Manufacturer CH-1033 Cheseaux / SWITZERLAND phone (021) 732 01 01 Copyright reserved for all countries telex 459 302 nagr ch February 1991 Edition Printed in Switzerland telefax (021) 732 01 00 http://www.nagraaudio.com NAGRA, KUDELSKI, NEOPILOT, NEOPILOTTON NAGRASTATIC, NAGRAFAX are registered trade - marks, property of KUDELSKI S.A. NAGRA Tape Recorders Manufacture NAGRA / KUDELSKI certifies that this instrument was thoroughly inspected and tested prior to leaving our factory and is in accordance with the data given in the accompanying test sheet. We guarantee the products of our own manufacture against any defect arising from faulty manufacture for a period of one year from the date of delivery. This guarantee covers the repair of confirmed defects or, if necessary, the replacement of the faulty parts, excluding all other indemnities. All freight costs, as well as customs duty and other possible charges, are at the customer's expense. Our guarantee remains valid in the event of emergency repairs or modifications being made by the user. However we reserve the right to invoice the customer for any damage caused by an unqualified person or a false maneuver by the operator. We decline any responsibility for any and all damages resulting, directly or indirectly, from the use of our products. Other products sold by KUDELSKI S.A. are covered by the guarantee clauses of their respective manufacturers. We decline any responsibility for damages resulting from the use of these products.
    [Show full text]
  • Common Tape Manipulation Techniques and How They Relate to Modern Electronic Music
    Common Tape Manipulation Techniques and How They Relate to Modern Electronic Music Matthew A. Bardin Experimental Music & Digital Media Center for Computation & Technology Louisiana State University Baton Rouge, Louisiana 70803 [email protected] ABSTRACT the 'play head' was utilized to reverse the process and gen- The purpose of this paper is to provide a historical context erate the output's audio signal [8]. Looking at figure 1, from to some of the common schools of thought in regards to museumofmagneticsoundrecording.org (Accessed: 03/20/2020), tape composition present in the later half of the 20th cen- the locations of the heads can be noticed beneath the rect- tury. Following this, the author then discusses a variety of angular protective cover showing the machine's model in the more common techniques utilized to create these and the middle of the hardware. Previous to the development other styles of music in detail as well as provides examples of the reel-to-reel machine, electronic music was only achiev- of various tracks in order to show each technique in process. able through live performances on instruments such as the In the following sections, the author then discusses some of Theremin and other early predecessors to the modern syn- the limitations of tape composition technologies and prac- thesizer. [11, p. 173] tices. Finally, the author puts the concepts discussed into a modern historical context by comparing the aspects of tape composition of the 20th century discussed previous to the composition done in Digital Audio recording and manipu- lation practices of the 21st century. Author Keywords tape, manipulation, history, hardware, software, music, ex- amples, analog, digital 1.
    [Show full text]
  • MD-2321 Book ETOC
    Contents Before using Important Safeguards........................ 2 MiniDisc Recorder Precautions ....................................... 3 Features............................................. 4 Supplied accessories......................... 4 Before operating this unit ................. 5 System connections .......................... 6 MD-2321 Operation Playing an MD.................................. 7 Recording to an MD ....................... 12 Using the program function (memory play) ............................. 19 Instruction Manual Editing the contents of an MD........ 20 Naming a track or disc.................... 24 A few important notes Precautions for handling the MiniDisc (MD) ...................... 26 Message list .................................... 26 Troubleshooting guide.................... 27 Rules for digital recording.............. 28 System limitations .......................... 29 Other informations Control positions and names .......... 30 Specifications ................................. 31 Thank you for purchasing the Onkyo MD-2321 Mini- Disc Recorder. Please read this manual thoroughly before making connections and plugging in the unit. Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new MD-2321. Please retain this manual for future reference. WARNING: WARNING AVIS TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, RISK OF ELECTRIC SHOCK RISQUE DE CHOC ELECTRIQUE DO NOT EXPOSE THIS APPLIANCE TO RAIN OR DO NOT OPEN NE PAS OUVRIR MOISTURE. The
    [Show full text]
  • What Is a Magnetic Tape Recorders
    What is a Magnetic Tape Recorders Before explaining about magnetic tape recorders, I will tell you what a recorder is and what the uses of the recorder are? A recorder is used to produce a permanent record of the signal that is measured. A record is used to analyse how one variable varies with respect to another and how the signal saries with time. The objective of a recording system is to record and preserve information pertaining to measurement at a particular time and also to get an idea of the performance of the unit and to provide the results of the steps taken by the operator. The basic components of a general recorder are an operating mechanism to position the pen or writer on the paper and a paper mechanism for paper movement and a printing mechanism. Okay, now you know what is a recorder, why it is used and where it is used. Now I will explain about magnetic tape recorder. A magnetic tape recorder is used to record data which can be retrieved and reproduced in electrical form again. This recorder can record signals of high frequency. Description of Magnetic Tape Recorders: The magnetic tape is made of a thin sheet of tough plastic material; one side of it is coated with a magnetic material (iron oxide). The plastic base is usually polyvinyl chloride (PVC) or polyethylene terephthalate. Recording head, reproducing head and tape transport mechanism are also present. Operation of Magnetic Tape Recorders: 1. The recording head consists of core, coil and a fine air gap of about 10 micrometer.
    [Show full text]
  • Dynametric 717 SOUTH MYRTLE AVENUE • MONROVIA, CALIFORNIA 91016-3422 626-358-2559 • FAX 626-359-5701 • 800-525-6925
    DynaMetric 717 SOUTH MYRTLE AVENUE • MONROVIA, CALIFORNIA 91016-3422 626-358-2559 • FAX 626-359-5701 • 800-525-6925 INSTRUCTIONS TMP-636S Telephone Transmit & Receive Patch For Use with Sound Card with PC Speakers P/N 44201 The TMP-636S Telephone Transmit & Receive Patch allows you to record and play back to your telephone from your PC sound card or tape recorder. Compatible with carbon and electret mics. It allows you to switch sound card operation between the phone and speakers or headphones. · Record telephone conversations · Record just your voice through your sound card (i.e. memos, repetitive, canned announcements…) · Playback from your sound card over the phone (announcements, music, phone conversations, etc.) or on your PC speakers or headphones Installation is easy, and operation is simple. The TMP-636S is compatible with analog and digital phones, and standard sound cards and tape recorders. You can leave it connected to your phone since it does not interfere with normal telephone operation. Will not record speakerphone. Install the TMP-636S according to the instructions below and operate your sound card controls as usual. Note: Make sure the "Monitor" switch on your sound card software (if any) is set to OFF to avoid feedback. Playback can be heard in your earphone and on the other end of the call with the switch in the ‘PHN’ position, or on your PC speakers or headphones in the ‘SPKR’ position. To Install: (See diagram) 1 Unplug handset (or headset) coil cord from the base of the telephone, and plug the short modular cord from TMP-636S in its place.
    [Show full text]
  • Summary of Meteorological Satellites
    Technical Summary of Meteorological Satellites TIROS – Television and Infra-Red Observation Satellite series Parameter TIROS I TIROS II TIROS III TIROS IV TIROS V TIROS VI TIROS VII TIROS VIII12 TIROS IX5 TIROS X 9 Launch Date 1/4/1960 23/11/1960 12/7/1961 8/2/1962 19/6/1962 18/9/1962 19/6/1963 21/12/1963 22/1/1965 2/7/1965 Deactivated 19/6/1960 1/2/1961 30/10/1961 30/6/1962 5/5/1963 11/10/1963 3/2/19661 1/7/19672 15/2/19673 3/7/19674 Lifetime 79 days 69 days 108 days 125 days 320 days 388 days 978 days 1258 days 754 days 732 days Pictures 19389 25574 24000 23370 48547 59830 111047 88662 76604 59119 Launcher Thor-Able Thor-Delta Thor-Delta Thor-Delta Thor-Delta Thor-Delta Thor-Delta Thor-Delta Thor-Delta Thor-Delta Site ETR ETR ETR ETR ETR ETR ETR ETR WTR ETR Pre-launch A1 A2 A3 A9 A50 A51 A52 A53 A54 OT-1 Designation 1960 2A 1960 16A 1961 17A 1962 2 A 1962 25A 1962 47A 1963 24A11 1963 54A 1965 4A 1965 51A 1960 β 2 1960 π 1 1961 ρ 1 1962 β 1 1962 αα 1 1962 αψ 1 Catalog No 29 63 162 226 309 397 604 716 978 1430 Apogee 867 km 837 937 972 1119 822 743 878 2967 957 Perigee 768 km 717 854 817 680 783 713 796 806 848 Inclination 48.392° 48.530° 47.898° 48.3° 58.1° 58.2° 58.2° 58.5° 96.4° 98.6° Period 99.24’ 98.26’ 100.4’ 100.4’ 100.5’ 98.7’ 97.4’ 99.3’ 119.2’ 100.6’ Mass 120 kg 125 129 129 129 127 135 119 138 127 Camera 1 TV-NA TV-NA TV-WA TV-WA TV-WA TV-WA TV-WA APT TV-WA TV-WA 3/5/62 14/5/63 21/10/63 31/8/64 Camera 2 TV-WA TV-WA TV-WA TV-MA TV-MA TV-MA TV-WA TV-WA TV-WA TV-WA 10/6/62 7/7/62 29/11/62 26/7/65 -/9/65 IR • • • • IRP • • • • HB
    [Show full text]
  • PDF Version of Recording Digital Audio
    Telling Your Story through Recording Digital Audio Digital Audio !On a computer Dr. Helen Barrett !On a digital tape recorder Researcher and Consultant Electronic Portfolios and ! Digital Storytelling for On an iPod Lifelong and Life Wide Learning On a Computer On a Digital Tape Recorder ! Software: Audacity ! Portable (free) ! Digital= Good Quality but Expensive ! Recommend using ! Analog= Lower Quality external but Cheap Microphone ! Transfer into computer ! Digital = file ! Need a Computer ! Analog = cable+software (less portability) Samson USB Mic Popular Digital Recorder On an iPod ! Records to SD Card ! Portable ! 320 kbps MP3 recording ! Requires special ! High-grade stereo condenser microphone built in microphone ($70) in ! Mic and Line audio inputs addition to iPod ! High speed file transfer via USB ! Transfer to computer 2.0 connection to computer as a digital file (WAV) ! Time & date stamp ! Long battery life (4 hour recording with AA alkaline type x 2) ! $400 1 Quality of Recording on iPod Steps in Recording on iPod ! 2 different quality levels: ! Settings in iTunes Low (default) and High ! NOTE: Voice Memos (from the xTreme Mac MicroMemo website) downloaded are removed from iPod ! Settings on iPod ! Extras -> Voice Memos -> Quality Set to High Always use the High rate for recording - you can’t increase the quality later Web 2.0 Development Tools What happens (Analog->Digital) ! Sound comes into ! The more samples per microphone second the greater ! the accuracy and Online Tools for ! Computer (or quality of the microphone)
    [Show full text]
  • Historical Development of Magnetic Recording and Tape Recorder 3 Masanori Kimizuka
    Historical Development of Magnetic Recording and Tape Recorder 3 Masanori Kimizuka ■ Abstract The history of sound recording started with the "Phonograph," the machine invented by Thomas Edison in the USA in 1877. Following that invention, Oberlin Smith, an American engineer, announced his idea for magnetic recording in 1888. Ten years later, Valdemar Poulsen, a Danish telephone engineer, invented the world's frst magnetic recorder, called the "Telegraphone," in 1898. The Telegraphone used thin metal wire as the recording material. Though wire recorders like the Telegraphone did not become popular, research on magnetic recording continued all over the world, and a new type of recorder that used tape coated with magnetic powder instead of metal wire as the recording material was invented in the 1920's. The real archetype of the modern tape recorder, the "Magnetophone," which was developed in Germany in the mid-1930's, was based on this recorder.After World War II, the USA conducted extensive research on the technology of the requisitioned Magnetophone and subsequently developed a modern professional tape recorder. Since the functionality of this tape recorder was superior to that of the conventional disc recorder, several broadcast stations immediately introduced new machines to their radio broadcasting operations. The tape recorder was soon introduced to the consumer market also, which led to a very rapid increase in the number of machines produced. In Japan, Tokyo Tsushin Kogyo, which eventually changed its name to Sony, started investigating magnetic recording technology after the end of the war and soon developed their original magnetic tape and recorder. In 1950 they released the frst Japanese tape recorder.
    [Show full text]
  • Digital Audio Tapes: Their Preservation and Conversion 1 Smithsonian Institution Archives Summer 2010
    Digital Audio Tapes: Their Preservation and Conversion 1 Smithsonian Institution Archives Summer 2010 Digital Audio Tapes: Their Preservation and Conversion Susan Eldridge, Digital Services Intern Overview Digital Audio Tapes (DATs) are 4mm (or 3.81mm) magnetic tape cassettes that store audio information in a digital manner. DATS are visually similar to compact audio cassettes, though approximately half the size, use thinner tapes, and can only be recorded on one side. Developed by Sony in 1987, DATs were quite popular in recording studios and were one of the first digital recording systems to become employed in archives in the late 1980s and 1990s due to their lossless encoding. Commercial use of DATs, on the other hand, never achieved the same success as the machines were expensive and commercial recordings were not available on DAT. Depending on the tape and machine used, DATs allow four different sampling modes: 32 kHz at 12 bits quantization, and 32 kHz, 44.1 kHz, and 48 kHz at 16 bits.1 All support two-channel stereo recording. Some of the later DATs (before being discontinued) could extend the bit-depth to 24 and up to 98 kHz, however, these tapes were likely rarely playable on other models.2 DATs can run between 15 and 180 minutes in length, one again depending on the tape and quality of the sampling. Unlike some other digital media, DATs do not use lossy data compression, which is important in the lossless transferring of a digital source to a DAT. Sony ultimately discontinued the production of DAT machines in 2005.3 Composition A digital magnetic tape is composed of two primary layers: the base film and magnetic layer.
    [Show full text]
  • Portable Cassette Tape Recorder Cassette Tape Compartment 14-1117 a DC 6V — Connect an Adapter and Use AC Or DC Power
    EAR — Connect the supplied earphone here for private listening. Portable Cassette Tape Recorder Cassette tape compartment 14-1117 A DC 6V — Connect an adapter and use AC or DC power. AUX — Connect an external audio source so that you can record from it. REM — Connect an external Step One microphone here if the Step Three Step Four microphone has remote Powering the Recorder control capability. Loading a Cassette Playing a Cassette 1. Remove any slack from the cassette tape 1. Load a cassette tape in the compartment. Installing Batteries by turning one of the hubs with a pencil. 1. Press down on the MIC — Connect an external The tape might become tangled in the 2. Rotate VOLUME to MIN for low sound. battery compartment microphone, if desired. MIN-VOLUME-MAX — Adjust record/playback mechanism if you do not cover and slide it in playback volume to the desired remove excess slack. the direction of the listening level. 3. Press PLAY. The tape begins to play. arrows to remove it. 2. Press STOP/EJECT to open the cassette Step Two compartment door. 4. Adjust VOLUME to the desired listening level. 2. Insert four size C batteries as indicated Connecting Earphones 3. Insert the tape with its open edge outward 5. To stop playback before the tape reaches the end, press by the polarity Use the supplied earphone for private listening. Insert the earphone’s toward the controls, and the desired side STOP/EJECT. Otherwise, the tape will automatically stop playing symbols marked facing up. once it reaches the end. inside. plug into the recorder’s EAR jack.
    [Show full text]
  • Magnetic Recording: Analog Tape
    Magnetic Recording: Analog Tape Until recently, there was one dominant way of recording sounds so that they could be reproduced at a later time or in a different location: analog magnetic recording (of course, there were mechanical methods like phonograph records, but they could not be recorded easily). In fact, magnetic recording techniques are still the most common way of recording signals, but the encoding method is digital. Magnetic recording relies on the imposition of a magnetic field, derived from an electrical signal, on a magnetically susceptible medium that becomes magnetized. The magnetic medium employed in analog recording is magnetic tape: a thin plastic ribbon with randomly oriented microscopic magnetic particles glued to the surface. The record head magnetic field alters the magnetic polarization (not the physical orientation) of the tiny particles so that they align their magnetic domains with the imposed field: the stronger the imposed field, the more particles align their orientations with the field, until all of the particles are magnetized. The retained pattern of magnetization stores the representation of the signal. When the magnetized medium is moved past a read head, an electrical signal is produced by induction. Unfortunately, the process is inherently very non-linear, so the resulting playback signal is different from the original signal. Much of the circuitry employed in an analog tape recorder is necessary to undo the distortion introduced by the non-linear physics of the system. Figure 1: In a record head, magnetic flux flows through low-reluctance pathway in the tape’s magnetic coating layer. Magnetic tape Magnetic tape used for audio recording consists of a plastic ribbon onto which a layer of magnetic material is glued.
    [Show full text]