Comcast DVR Remote Manual

FEATURES AND FUNCTIONS Use Page+ (or Page–) switch to an input works. If it still does not work, try release Setup. control the device’s volume only De-Activating Channel Control Lock source. Searching For Your Code. in its own mode. to page up (or down) 3. Enter 9 - 9 - 0. The TV key will 1. On the remote control, press Use the remote control’s mode keys through menu screens (i.e., AUX, TV, or Cable) to control a spe- Use Enter to enter NOTE: If the device does not have a blink twice. Cable once. Then press and hold and the interactive Power key, press the (Play) key. cific device. When pressed, the selected channels on some TV 4. To view the code for the first digit, Unlocking All Volume Controls Setup until the Cable key blinks Comcast Custom DVR 3-Device program guide. models or information mode key will light, confirming your 7. For future reference, write your press 1 once. Wait 3 seconds and (Global Volume Unlock): twice, then release Setup. Universal Remote Control choice. Use the other keys to perform Use Guide to display on menu screens. count the number of times the TV device code in the appropriate 1. Press and hold Setup until the 2. Enter 9 - 7 - 3. Press CH- once. desired actions (see the following key the interactive key blinks (e.g., 3 blinks = 3) and Press PIP On-Off to boxes below: selected mode key blinks twice, The Cable key will blink four chart). program guide. write down the number in the display the PIP AUX Code: then release Setup. times. Use these keys to move Window. leftmost TV Code box (at end of NOTE: The selected mode will remain active this section). 2. Enter 9 - 9 - 3 and then press 3. Now, the remote control will until you press another mode key. the cursor in the inter- >Use PIP Swap to VOL+ once. The mode key will provide TV or cable channel active program guide NOTE: If a code digit is “0”, the select- control capabilities while in the Press AUX, TV, or Cable switch the images and blink four times confirming and menu screens. ed mode key will not blink. TV or Cable mode. once to select and sound between the Device Type:______________ unlock. Use OK (Select)to select control a device. main and window pic- 5. Repeat step 4 three more times for 3. Now, volume controls for all menu options, PPV tures. the remaining digits. Use 2 for the Press Power once to TV Code: devices can be independently Re-Activating Channel Control Lock events, and programs second digit, 3 for the third digit, controlled in their own modes. turn on or off the from the interactive Use PIP Move to move and 4 for the fourth digit. Finish 1. On the remote control, press selected home enter- program guide. the picture to different writing down the code in the TV Cable once. Then press and hold tainment device. Locking Volume Control To TV Mode positions in the main 8. Repeat steps 1 to 7 for another Code boxes (at end of this sec- (Restoring Global Volume Lock To Setup until the Cable key blinks Use Info to display picture. tion). twice, then release Setup. Use Setup for all current channel and device you want to control. The Default Mode): programming 2. Enter 9 - 7 - 3. Press CH+ once. program information. Use PIP CH + (or CH -) 6. To check another device code, sequences. 1. Press TV once. Then, press and The Cable key will blink twice. to select the next high- repeat steps 1 to 5, but substitute Use Menu to display the AUX key for the auxiliary hold Setup until the TV key blinks Press All On once to the Quick Menu (on a er or lower PIP SEARCHING FOR YOUR CODE twice, then release Setup. 3. Now, regardless if you select the turn on or off all device you are checking. Write Motorola, GI, or channel. If your home entertainment device does TV or Cable mode, only the chan- programmed devices down the codes in the appropriate 2. Enter 9 - 9 - 3 and then press TV nel control capability of your Jerrold Cable Box), or not respond to the remote control after in this order: Cable, boxes below: once. The mode key will blink cable box will be accessible. to access settings (on a trying all of the codes listed for your TV, and AUX. After all twice confirming global lock. Scientific Atlanta PROGRAMMING DEVICE brand, or if your brand is not listed at all, AUX Code: devices are on, Cable Explorer, Pioneer CONTROL try searching for your code. 3. Now, when you press VOL+, VOL-, is the active mode. Voyager, or PACE or Mute, the volume of the select- TROUBLESHOOTING For example, after trying all of the Press ON DEMAND once cable box). The Comcast Custom 3-Device univer- ed device (e.g., TV) will be con- PROBLEM: A mode key does not blink codes for your TV, you still cannot get to access Comcast’s ON sal remote control is preprogrammed at trolled regardless of the mode when you press a key. Use Exit to exit the the remote control to operate your TV, Device Type:______________ DEMAND menu (not the factory to operate the Cable Box you have selected. menu or guide. supplied by your Comcast system, an then: SOLUTION: Replace the batteries with available in all areas). TV Code: two (2) new AA batteries. Use Help to access RCA TV, and an RCA VCR (in the AUX 1. Turn on your TV. User Guide In the AUX or TV mode, digital cable help. mode). To control devices other than PROBLEM: During programming, a use the transport keys default brands (excluding the Cable 2. On the remote control, press TV REASSIGNING DEVICE KEYS mode key displays one to control a VCR, Use Last to recall the Box), perform the below steps; other- once. Then press and hold Setup The Comcast Custom 3-Device universal long blink. OVERVIEW PVR, or DVD player. last channel or go back wise skip this section: until the TV key blinks twice, then remote control can be set up to control SOLUTION: An invalid entry has To record a program one screen in the menu. release Setup. a second device. occurred. Check the key The Comcast Custom DVR 3-Device 1. Turn on a device (e.g., VCR or DVD CHANGING VOLUME LOCK on a VCR, press REC Use VOL+ (or VOL-) 3. Enter 9 - 9 - 1. The TV key will to be entered and try universal remote will control up to twice. Player) and, if applicable, insert For example, to have the unit control a to raise (or lower) the media, (e.g., video cassette or disc). blink twice. The Comcast Custom 3-Device universal programming again. three home entertainment devices, remote control is set at the factory to TV, a Cable Box, and second TV, you In the Cable mode, use sound volume. Also PROBLEM: A mode key blinks when including a Digital Video Recorder NOTE: Please read steps 2 to 6 complete- 4. Aim the remote control at the the control the TV volume in all modes. will need to reassign the unused AUX the keys to control ON see Changing Volume you press a key, but home enabled Cable Box (used by Comcast ly before proceeding. Highlight or write TV and slowly alternate between key to operate the second TV as fol- DEMAND programs. Lock. entertainment compo- Systems). down the codes and device you wish to pressing Power and TV. However, you may change the Volume lows: Press Mute once to Lock setting to Individual Volume nent does not respond. The remote control requires installing Press REPLAY to replay program before moving on to step 2. Stop when the TV turns off. A 1. On the remote control, press AUX the previous few turn sound off or on. Unlock to unlock a specific device’s vol- SOLUTION: Make sure the remote two (2) new AA batteries (included) 2. On the remote control, press a working code has been found. ume controls for independent opera- once. Then press and hold Setup seconds of a program. AUX key blinks twice, control is aimed at your In the Cable mode, device key once (i.e., AUX or TV). tion in its own mode (e.g., Audio until the and some easy programming to con- NOTE: In the search mode, the then release Setup. home entertainment trol your devices. For best results, Press My DVR to show press FAV once to remote control will send IR codes Receiver volume controls in the AUX device and is not farther display programmed NOTE: Use the AUX key to program please read and perform all instruc- a list of programs that control of an Audio Amplifier or from its library to the selected device, mode). 2. Enter 9 - 9 - 2. The AUX key will than 15 feet away. have been recorded. favorite cable channels. blink twice. tions listed here. Also, keep this guide Receiver, a DVD Player, a Home- starting with the most popular code Or, if desired, you can perform Global PROBLEM: The remote control does for future reference. Press LIVE to return to Use CH+ (or CH-) to Theater-In-A-Box Device, a PVR (or first. Volume Unlock so that the volume 3. Press TV once, then press AUX not control home enter- watching live TV. select the next higher DVR), or a VCR. 5. Press Setup once to lock in the controls of all devices can be indepen- once.

Load more