DOCSLIB.ORG

Accident-Tolerant Control Rod

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Accident-Tolerant Control Rod NEA/NSC/DOC(2013)9 Accident-tolerant control rod Hirokazu Ohta, Takashi Sawabe, Takanari Ogata Central Research Institute of Electric Power Industry (CRIEPI), Japan Boron carbide (B4C) and hafnium (Hf) metal are used for the neutron absorber materials of control rods in BWRs, and silver-indium-cadmium (Ag-In-Cd) alloy is used in PWRs. These materials are clad with stainless steel. The eutectic point of B4C and iron (Fe) is about 1 150°C and the melting point of Ag-In-Cd alloy is about 800°C, which are lower than the temperature of zircaloy – steam reaction increases rapidly (~1 200°C). Accordingly, it is possible that the control rods melt and collapse before the reactor core is significantly damaged in the case of severe accidents. Since the neutron absorber would be separated from the fuels, there is a risk of re-criticality, when pure water or seawater is injected for emergency cooling. In order to ensure sub-criticality and extend options of emergency cooling in the course of severe accidents, a concept of accident-tolerant control rod (ACT) has been derived. ACT utilises a new absorber material having the following properties: • higher neutron absorption than current control rod; • higher melting or eutectic temperature than 1 200°C where rapid zircaloy oxidation occurs; • high miscibility with molten fuel materials. The candidate of a new absorber material for ATC includes gadolinia (Gd2O3), samaria (Sm2O3), europia (Eu2O3), dysprosia (Dy2O3), hafnia (HfO2). The melting point of these materials and the liquefaction temperature with Fe are higher than the rapid zircaloy oxidation temperature. ACT will not collapse before the core melt-down. After the core melt-down, the absorber material will be mixed with molten fuel material. The current absorber materials, such as B4C, Hf and Ag-In-Cd, are charged at the tip of ATC in which the neutron flux is high, and a new absorber material is charged in the low- flux region, as shown in Figure 1. This design could minimise the degradation of a new absorber material by the neutron absorption and the influence of ATC deployment on reactor control procedure. As a result, the new absorber material may be recycled. Figure 1: Design of ACT, (a) BWR type and (b) PWR type Core End plug B4C End plug (Current control rod) Stainless Spring ball Stainless Stainless cladding cladding Ge2O3 or Ge2O3 or , Ge2O3-HfO 2 , Ge2O3-HfO2 etc... etc... Dimple Ag-In-Cd (Current End plug control rod) End plug Core (a) BWRs (b) PWRs INCREASED ACCIDENT TOLERANCE OF FUELS FOR LIGHT WATER REACTORS, © OECD 2013 29 Accident Tolerant Control Rod CRIEPI (Central Research Institute of Electric Power Industry) H. Ohta, T. Sawabe, T. Ogata International Workshop on Accident Tolerant Fuels of LWRs 10-12 Dec. 2012 1 Current control rod in LWRs BWR: Boron carbide (B4C) powder (with stainless steel cladding) Metallic Hafnium (Hf) (with Stainless sheath) PWR：Silver – Indium – Cadmium (Ag-In-Cd) alloy (with stainless steel cladding) Boric acid (H3BO3) (= chemical shim) Main structure material: Austenitic Steel 金属ハフ二ウム （プレートタイプ） Control rod for BWRs Control rod for PWRs 2 Behavior of current control rod at SA 2850 melting of UO2 2850 melting of UO2 BWR 2810 melting of HfO2 PWR 2810 melting of HfO2 2710 melting of ZrO 2710 melting of ZrO2 2 2600 eutectic of UO -ZrO 2600 eutectic of UO2-ZrO2 2 2 2570 melting of PuO2 2570 melting of PuO2 2400 monotectic of α-Zr(O)-UO2 and U-UO2 2400 monotectic of α-Zr(O)-UO2 and U-UO2 2350 melting of B4C 2350 melting of B4C 2310 2310 melting of Gd O melting of Gd2O3 2 3 2222 melting of Hf 2222 melting of Hf 2180 melting of B 2180 melting of B ) 2054 melting of Al2O3 ) ℃ ℃ 1975 melting of α-Zr(O) 1975 melting of α-Zr(O) 1900 eutectic of Al O -UO and Al O -ZrO 1852 melting of Zr 2 3 2 2 3 2 Start of UO2 dissolution 1852 melting of Zr by molten Zirca loy → Start of UO2 dissolution 1760 melting of Zirca loy Temperature ( 1760 melting of Zirca loy by molten Zirca loy → Temperature ( forma tion of meta llic (U, Zr, O) melt forma tion of meta llic (U, Zr, O) melt 1536 melting of Fe 1536 melting of Fe 1455 melting of Ni 1455 melting of Ni 1450 melting of sta inless steel and Inconel 1450 melting of stainless steel and Inconel 1410 boiling of NaCl, MgCl2 1300 eutectic of Fe-Zr 1300 eutectic of Al(Al2O3)-Zr, Fe-Zr and Ni-Zr Start of rapid Zirca loy Start of rapiｄ 1200 eutectic of Ni-Zr oxidation by H2O → 1200 eutectic of Ag-Zr and Ni-Zr Uncontrolled Zirca loy oxidation by 1150 eutectic of B4C-Fe 1150 eutectic of B4C-Fe H2O → 1133 temperature escalation 1133 melting of U melting of U Uncontrolled temperature 940 eutectic of Fe-Zr and Ni-Zr 940 eutectic of Fe-Zr and Ni-Zr esca la tion ⇒ Control materials would 801 melting of NaCl 800 melting of Ag-In-Cd 714 melting of MgCl2 melt and fall down before 450 eutectic of NaCl-MgCl2 severe core damage. o ⇒ Injecting pure (sea) water Eutectic of Fe-Zr (940 C) Rapid Zircaloy oxidation by H2O o ≦ o into core would lead to Eutectic of Fe-B4C (1150 C) (~1200 C) o o dilution of boric acid Melting of Ag-In-Cd (800 C) Melting of Zircaloy (1760 C) concentration. 3 TMI-2 relocation Boric acid Upper debris bed Molten metal and ceramic Control, structural, and cladding material solidified between fuel rods 4 Accident Tolerant Control rod (ATC) 1. To keep enough shutdown margin at sever accident. Neutron absorber materials should have following properties: 1) Higher neutron absorption than current control rod Gd, Sm, Eu , Dy etc. 2) Higher melting or eutectic point than ~1200oC where rapid Zircaloy oxidation occurs Gd2O3, Sm2O3, Eu2O3, Dy2O3 etc. 3) High miscibility with molten fuel materials Miscible with UO2 = Gd2O3, HfO2 etc. 2. To minimize the influence on the peration conditions of reactors, and To keep control rod worth for a long-term. （ ） 4) High neutron flux regions, loading current control rod B4C or Ag-In-Cd . Mitigate the effect on reactor control in operation 5) Low flux regions, loading ATC materials. Increase of shutdown margin & Long-term use of control rod ※ ATCR materials are reused. 5 Concept of ATC BWRs PWRs B4C or Hf Current Ag-In-Cd Core Core control rod Gd2O3 or Gd2O3-HfO2 etc. - Absorbers: Gd2O3 / HfO2 -To keep burnable poison (Gd2O3) for a long- ATC term Core under operation Core - To minimize the influence on reactor operation. → Vicinity of core: current materials - Higher shutdown margin than current control rod ATC Core Core - Restrictive loss of burnable poison during shutdown → Reusable -Remaining in the core material at SA or Sever accident overheating → Gd2O3 / HfO2 would mix with core debris 6 Structure of ATC BWRs PWRs Core End plug End plug Current control rod B4C (B4C) Stainless ball Spring B4C Stainless Stainless cladding cladding ATC ATC B4C （Ge2O3 or Ge2O3-HfO2） Ag-In-Cd （Ge2O3 or Ge2O3-HfO2） Dimple Ag-In-Cd B C Current control rod 4 (Ag-In-Cd) End plug End plug (a) Current (b) ATC (a) Current (b) ATC control rod control rod Upper part is Core Lower part is same as Current same as Current CR structure CR structure 7 Future works To improve the accident tolerance without significant effect on reactor control in operation, we will confirm (1) Neutron absorption worth of ATC materials, Gd2O3 or Gd2O3 - HfO2 (2) Life time of ATC, Loading position (3) Melting behavior of ATC materials, Compatibility with structural materials, Gd2O3, Gd2O3 - HfO2, Gd2O3 - Fe, Gd2O3 - Zr etc. (4) Miscibility with molten core materials. UO2 - Gd2O3, UO2 - HfO2, ZrO2 - Gd2O3 , Gd2O3 - Fe, etc. 8 .
Load more

Recommended publications
  • Study of Advanced Lwr Cores for Effective Use of Plutonium and Mox Physics Experiments
    STUDY OF ADVANCED LWR CORES FOR EFFECTIVE USE OF PLUTONIUM AND MOX PHYSICS EXPERIMENTS T. YAMAMOTO, H. MATSU-URA*, M. UEJI, H. OTA XA9953266 Nuclear Power Engineering Corporation, Toranomon, Minato-ku, Tokyo T. KANAGAWA Mitsubishi Heavy Industries, Ltd, Nishi-ku, Yokohama K. SAKURADA Toshiba Corporation, Isogo-ku, Yokohama H.MARUYAMA Hitachi, Ltd, Hitachi-shi Japan Abstract Advanced technologies of full MOX cores have been studied to obtain higher Pu consumption based on the advanced light water reactors (APWRs and ABWRs). For this aim, basic core designs of high moderation lattice (H/HM ~5) have been studied with reduced fuel diameters in fuel assemblies for APWRs and those of high moderation lattice (H/HM ~6) with addition of extra water rods in fuel assemblies for ABWRs. The analysis of equilibrium cores shows that nuclear and thermal hydraulic parameters satisfy the design criteria and the Pu consumption rate increases about 20 %. An experimental program has been carried out to obtain the core parameters of high moderation MOX cores in the EOLE critical facility at the Cadarache Centre as a joint study of NUPEC, CEA and CEA's industrial partners. The experiments include a uranium homogeneous core, two MOX homogeneous cores of different moderation and a PWR assembly mock up core of MOX fuel with high moderation. The program was started from 1996 and will be completed in 2000. 1. INTRODUCTION In Japan, the MOX fuel demonstration programs have been performed successfully and reload size use of MOX fuel has been prepared. The recycling of plutonium in light water reactors is expected to continue in several decades.
    [Show full text]
  • Detailed B Depletion in Control Rods Operating in a Nuclear Boiling
    UPTEC K11 015 Examensarbete 30 hp Februari 2011 Detailed 10B depletion in control rods operating in a Nuclear Boiling Water Reactor John Johnsson Abstract Detailed 10B depletion in control rods operating in a Nuclear Boiling Water Reactor John Johnsson Teknisk- naturvetenskaplig fakultet UTH-enheten In a nuclear power plant, control rods play a central role to control the reactivity of the core. In an inspection campaign of three control rods (CR 99) operated in the Besöksadress: KKL reactor in Leibstadt, Switzerland, during 6 respectively 7 consecutive cycles, Ångströmlaboratoriet Lägerhyddsvägen 1 defects were detected in the top part of the control rods due to swelling caused by 10 Hus 4, Plan 0 depletion of the neutron-absorbing B isotope (Boron-10). In order to correlate these defects to control rod depletion, the 10B depletion has in this study been Postadress: calculated in detail for the absorber pins in the top node of the control rods. Box 536 751 21 Uppsala Today the core simulator PLOCA7 is used for predicting the behavior of the reactor Telefon: core, where the retrievable information from the standard control rod follow-up is 018 – 471 30 03 the average 10B depletion for clusters of 19 absorber holes i.e. one axial node. 10 Telefax: However, the local B depletion in an absorber pin may be significantly different 018 – 471 30 00 from the node average depletion that is re-ceived from POLCA7. To learn more, the 10B depletion has been simulated for each absorber hole in the uppermost node using Hemsida: the stochastic Monte Carlo 3D simulation code MCNP as well as an MCNP- based http://www.teknat.uu.se/student 2D-depletion code (McScram).
    [Show full text]
  • Boiling Water Reactor Control Rod CR 82M-1
    Nuclear Fuel Boiling Water Reactor Control Rod CR 82M-1 Background CR 82M-1 Design The boiling water reactor (BWR) control rod of The hafnium tip of the CR 82M-1 design protects today must meet high operational demands and at the control rod from absorber material swelling the same time contribute to decreased operational when operated in the shutdown mode; i.e., costs for the plant operator. withdrawn from the core. The flexible B4C inventory allows for either matched or high- Description reactivity worth control rods. As structural material, American Iron and Steel Institute 316L stainless The Westinghouse BWR control rod design steel is an irradiation-resistant steel, not readily consists of four stainless steel sheets welded sensitized to irradiation-assisted stress corrosion together to form a cruciform-shaped rod. Each cracking. With an extremely low-cobalt content sheet has horizontally drilled holes to contain the (< 0.02%) in the wing material, these control rods absorber materials (B4C powder and hafnium). can play a significant role in as-low-as-reasonably- This design allows significantly more B4C to be achievable efforts. The design, with horizontally contained in the rod compared to the original drilled absorber holes, limits the washout of control rods of most reactors. B4C in the event of an anomaly in a wing, thus maintaining full reactivity worth. Westinghouse CR 82M-1 control rod for all types of BWRs Westinghouse BWR control rod CR 82M-1 Benefits CR 82M-1 is an evolutionary design based on 45 years of control rod operation
    [Show full text]
  • Apr1400 Design Control Document Tier 2
    APR1400 DESIGN CONTROL DOCUMENT TIER 2 CHAPTER 4 REACTOR APR1400-K-X-FS-14002-NP REVISION 0 DECEMBER 2014 2014 KOREA ELECTRIC POWER CORPORATION & KOREA HYDRO & NUCLEAR POWER CO., LTD All Rights Reserved This document was prepared for the design certification application to the U.S. Nuclear Regulatory Commission and contains technological information that constitutes intellectual property. Copying, using, or distributing the information in this document in whole or in part is permitted only by the U.S. Nuclear Regulatory Commission and its contractors for the purpose of reviewing design certification application materials. Other uses are strictly prohibited without the written permission of Korea Electric Power Corporation and Korea Hydro & Nuclear Power Co., Ltd. Rev. 0 APR1400 DCD TIER 2 CHAPTER 4 – REACTOR TABLE OF CONTENTS NUMBER TITLE PAGE CHAPTER 4 – REACTOR ............................................................................................ 4.1-1 4.1 Summary Description ......................................................................................... 4.1-1 4.1.1 Initial Core Design Description and Permissible Changes ..................... 4.1-2 4.1.2 Analytical Techniques ............................................................................ 4.1-2 4.1.3 Combined License Information .............................................................. 4.1-2 4.2 Fuel System Design ............................................................................................. 4.2-1 4.2.1 Design Bases .........................................................................................
    [Show full text]
  • Performance Comparison of Different Absorbent Materials in BWR Control Rods
    PHYSOR 2004 -The Physics of Fuel Cycles and Advanced Nuclear Systems: Global Developments Chicago, Illinois, April 25-29, 2004, on CD-ROM, American Nuclear Society, Lagrange Park, IL. (2004) Performance Comparison of Different Absorbent Materials in BWR Control Rods José L. Montes*1, Juan J. Ortiz1, Raul Perusquía1 and Robert T. Perry2 1Instituto Nacional de Investigaciones Nucleares, Carr. México-Toluca Km. 36.5., Ocoyoacac Edo. De México, México. 2Los Alamos National Laboratory, PO Box 1663, Los Alamos, NM 87545, USA Nowadays there is a trend of increasing the cycle length of commercial operation in nuclear reactors. This demands to control a greater quantity of reactivity excess in this type of cycles. In this work, a comparative study of the use of various absorbent materials in the control rods of a BWR is presented. The behavior of the different absorbent material used is accomplished only from the neutron point of view. The capability of each different material to control the reactor is analyzed by studying the required control rod density and the complexity to design the target control rod patterns (CRP). The system GACRP was used to generate the target control rods patterns for an 18 months equilibrium cycle. This system is based on genetic algorithms computational technique. The found results show that the behavior of the dysprosium is acceptable and very similar to the boron one. In average, both require around 4.3% of control rod density, while in Hf cases 5.1% is needed. Although the greatest impact of including different absorbent material is noted in cold condition, GACRP could obtain a CRP in any of the considered cases.
    [Show full text]
  • Application of the Dynamic Control Rod Reactivity Measurement Method to Korea Standard Nuclear Power Plants
    PHYSOR 2004 – The Physics of Fuel Cycles and Advanced Nuclear Systems: Global Developments Chicago, Illinois, April 25-29, 2004, on CD-ROM, American Nuclear Society, Lagrange Park, IL. (2004) Application of the Dynamic Control Rod Reactivity Measurement Method to Korea Standard Nuclear Power Plants E. K. Lee*, H. C. Shin, S. M. Bae and Y. G. Lee Korea Electric Power Research Institute, Yusung, Daejeon 305-380, Korea To measure and validate the worth of control bank or shutdown bank, the dynamic control rod reactivity measurement (DCRM) technique has been developed and applied to six cases of Low Power Physics Tests of PWRs including Korea Standard Nuclear Power plant (KSNP) based on the CE System 80 NSSS. Through the DORT results for each two ex-ore detector response and the three dimensional core transient simulations for rod movements, the key parameters of DCRM method are determined to implement into the Direct Digital Reactivity Computer System (DDRCS). A total of 9 bank worths of two KSNP plants were measured to compare with the worths of the conventional rod worth measurement method. The results show that the average error of DCRM method is nearly the same as the conventional Rod Swap and Boron Dilution Method but lower standard deviation. It takes about twenty minutes from the beginning of rod movement to final estimation of the integral static worth of a control bank. KEYWORDS: Dynamic Reactivity, Low Power Physics Test, Control Bank, DCRM, Rod Swap method, Boron dilution method 1. Introduction To measure the worth of control banks and shutdown banks during the Low Power Physics Test (LPPT) program of Pressurized water reactors (PWRs), the boron dilution technique and the rod swap method (RSM) are used over 20 years in KOREA.
    [Show full text]
  • BWR Control Rod CR 82M-1TM
    Fuel Delivery BWR Control Rod CR 82M-1TM Background The boiling water reactor (BWR) control rod (CR) of today must meet high operational demands and at the same time contribute to decreased operational costs for the plant operator. Westinghouse BWR Control Rod Design The Westinghouse BWR control rod design consists of four stainless steel sheets welded together to form a cruciform-shaped rod. Due to this configuration, the product is also known as control rod blade (CRB). Each sheet has horizontally drilled holes to contain absorber material, boron carbide (B4C) and hafnium. This design allows significantly more B4C to be contained in the rod, offering a longer service life versus traditional control rods in most reactors. CR 82M-1TM Design CR 82M-1 has mainly B4C powder as absorber material, but the holes in the top area are filled with hafnium. B4C swells due to neutron capture, while hafnium does not. When it was realized in the early 1980´s that control rods when fully withdrawn from the core also obtained neutron irradiation, Westinghouse started to use hafnium at the top to avoid interaction of a swelling absorber with the walls of the holes that leads to stress corrosion cracking. CR 82M-1 is an evolutionary development of the CR 82 control rod, which utilized hafnium at the top of the control rod. A higher quality stainless steel 316L is used in CR 82M-1 instead of the 304L material in CR 82. Another benefit of hafnium is the extended nuclear life, since several hafnium isotopes form new neutron absorbing isotopes due to neutron capture.
    [Show full text]
  • The First Reactor.Pdf
    .-. DISCLAIMER This repofi was.prepared as an account of work sponsored by an agency of the United States Government. Neither the United States Government nor any agency thereof, nor any of their employees, make any warranty, express or implied, or assumes any legal liability or responsibility for the accuracy, completeness, or usefulness of any information, apparatus, product, or process disclosed, or represents that its use would not infringe privateiy owned rights. Reference herein to any specific commercial product, process, or service by trade name, trademark, manufacturer, or otherwise does not necessarily constitute or imply its endorsement, recommendation, or favoring by the United States Government or any agency thereof. The views and opinions of authors expressed herein do not necessarily state or reflect those of the United States Government or any agency thereof. DISCLAIMER Portions of this document may be illegible in electronic image products. Images are produced from the best available original document. : The FirstReactor @ U.S. Department of Energy %~ Assistant Secretary for Nuclear Energy T** . and Assistant .%cretary, Management A~f + $a:$;g:::~;.0;0585 @$*6R December 1982 $ This report has been reproduced directly from the best available copy. ,! Available from the National Technical Information Service, U.S. Department of Commerce, Springfield, Virginia 22161. Price: Printed Copy A03 Microfiche AOI Codes are used for Pricing all publications. The code is determined by the number of pages in the publication. Information pertaining to the pricing codes can be found in the current issues of the following publications, which are generally available in most Iibraries: Energy Research Abstracts, (ERA); Government Reports Announcements and 1ndex (GRA and 1); Scientific and Technical Abstract Reports (STAR); and pub- lication, NTIS-PR-360 available from (NTIS) at the above address.
    [Show full text]
  • The Effects of Fuel Type on Control Rod Reactivity of Pebble-Bed Reactor 133
    NUKLEONIKA 2019;64(4):131138 doi: 10.2478/nuka-2019-0017 ORIGINAL PAPER © 2019 Zuhair, Suwoto, T. Setiadipura & J. C. Kuijper. This is an open access article distributed under the Creative Commons Attribution-NonCommercial-NoDerivatives 3.0 License (CC BY-NC-ND 3.0). The effects of fuel type on control Zuhair, Suwoto, rod reactivity of pebble-bed reactor Topan Setiadipura, Jim C. Kuijper Abstract. As a crucial core physics parameter, the control rod reactivity has to be predicted for the control and safety of the reactor. This paper studies the control rod reactivity calculation of the pebble-bed reactor with three scenarios of UO2, (Th,U)O2, and PuO2 fuel type without any modifi cations in the confi guration of the reactor core. The reactor geometry of HTR-10 was selected for the reactor model. The entire calculation of control rod reactivity was done using the MCNP6 code with ENDF/B-VII library. The calculation results show that the total reactivity worth of control rods in UO2-, (U,Th)O2-, and PuO2-fueled cores is 15.87, 15.25, and 14.33%k/k, respectively. These results prove that the effectiveness of total control rod in thorium and uranium cores is almost similar to but higher than that in plutonium cores. The highest reactivity worth of individual control rod in uranium, thorium and plutonium cores is 1.64, 1.44, and 1.53%k/k corresponding to CR8, CR1, and CR5, respectively. The other results demonstrate that the reactor can be safely shutdown with the control rods combination of CR3+CR5+CR8+CR10, CR2+CR3+CR7+CR8, and CR1+CR3+CR6+CR8 in UO2-, (U,Th)O2-, and PuO2-fueled cores, respectively.
    [Show full text]
  • Core Design and Transient Analyses for Weapons Plutonium Burning in Vver-1000 Type Reactors
    CORE DESIGN AND TRANSIENT ANALYSES FOR WEAPONS PLUTONIUM BURNING IN VVER-1000 TYPE REACTORS Ulrich Rohde, Ulrich Grundmann, Yaroslav Kozmenkov1, Valery Pivovarov1, and Yuri Matveev1 1. Introduction The presented core calculations are aimed at the demonstration of the feasibility of weapon- grade plutonium burning in VVER-1000 type reactors with emphasis on safety aspects of the problem. Particular objectives of weapon-grade Pu burning are the net burning of fissile Pu isotopes in general, but also the conversion of the Pu vector of the fuel from weapon-grade to reactor plutonium. While weapon-grade plutonium is almost pure fissile 239Pu, reactor pluto- nium is a mixture of the Pu isotopes 238, 239, 240, 241 and 242, which is not suitable for weapons. The even number isotopes are decaying spontaneously releasing neutrons, which would make a bomb un-controllable. Moreover, 238Pu decays with high heat release emitting alpha radiation. An amount of perhaps about 200 tons of weapon-grade plutonium has piled up world wide. Russia has declared to burn or convert about 34 tons of weapon-grade Pu [1]. The reactor physics analyses on Pu burning consist on the following steps: • Fuel element design • Core design • Burn-up calculations to get the equilibrium cycle • Analysis of reactivity initiated accidents (RIA) The static design calculations are aimed at the proof that the design limits for the reactor core like maximum power peaking factors, maximum linear rod power or maximum coolant heat- up are met. The analysis of RIA has to demonstrate that no safety limits are exceeded during the transients. The background of the RIA analyses is the fact, that core loadings with MOX fuel are characterized by specific reactivity features, which are different from UOX fuel load- ings: • The Doppler coefficient of the reactivity is more negative, since plutonium isotopes have large resonance capture.
    [Show full text]
  • 4. Reactor AP1000 Design Control Document
    4. Reactor AP1000 Design Control Document 4.2 Fuel System Design The plant conditions for design are divided into four categories. • Condition I - normal operation and operational transients • Condition II - events of moderate frequency • Condition III - infrequent incidents • Condition IV - limiting faults Chapter 15 describes bases and plant operation and events involving each condition. The reactor is designed so that its components meet the following performance and safety criteria: • The mechanical design and physical arrangement of the reactor core components, together with corrective actions of the reactor control, protection, and emergency cooling systems (when applicable) provide that: – Fuel damage, that is, breach of fuel rod clad pressure boundary, is not expected during Condition I and Condition II events. A very small amount of fuel damage may occur. This is within the capability of the plant cleanup system and is consistent with the plant design bases. – The reactor can be brought to a safe state following a Condition III event with only a small fraction of fuel rods damaged. The fraction of fuel rods damaged must be limited to meet the dose guidelines identified in Chapter 15 although sufficient fuel damage might occur to preclude immediate resumption of operation. – The reactor can be brought to a safe state and the core kept subcritical with acceptable heat transfer geometry following transients arising from Condition IV events. • The fuel assemblies are designed to withstand non-operational loads induced during shipping, handling, and core loading without exceeding the criteria of subsection 4.2.1.5.1. • The fuel assemblies are designed to accept control rod insertions to provide the required reactivity control for power operations and reactivity shutdown conditions.
    [Show full text]
  • Use of the Fast Flux Test Facility for Tritium Production
    Use of the Fast Flux Test Facility for Tritium Production S. Drell, Co-chair D. Hammer, Co-chair J. M. Cornwall F. Dyson R. Garwin W. Happer October 1996 JSR-96-325 Approved for public release; distribution unlimited. 19961212 090 JASON The MITRE Corporation 1820 Dolley Madison Boulevard Mclean, Virginia 22102-3481 MIC QUALITY lNSflECTED 1 Fon» Approved REPORT DOCUMENTATION PAGE OM8 No. 0704-0188 Public reporting burden for this colklctlon d Information Htimated to everage 1 hour per re.ponse. Including the time for revieW Instructions ...arc hlng existing data IQUrCIIS. gathering and malntelnlng the data needed. and completing and reviewing the collection of Inlormation. Send comment. reg81dlng this burden estimate or any other apect of this coIlecUon d Information. Inc:ludlng suggestion. for reducing this burden. to Washington Headquarter. Service •• Directorate for Infonnation Operations and Report" 121 S Jelferson OlIVia Hlgh_y. Suite 1204. Arlington. VA 22202~02. and to the Office d Management and Budget. Paperwork Reduction ProJect (0704-01B8). Wa.hlngton. DC 20503. 1. AGENCY USE ONLY (Le.ve blan/() 12. REPORT DATE /3. REPORT TYPE AND DATES COVERED Odober 25, 1996 4. TITLE AND SUBTITLE 5. RJNDING NUMBERS Use of the Fast Flux Test Facility for Tritium Production 6. AUTHOR(S) 13-958534-04 J. Cornwall, S. Drell, F. Dyson, R. Garwin, D. Hammer, W. Happer 7. PERFORMING ORGANIZATION NAME(S) AND ADDRESS(ES) 8. PERFORMING ORGANIZATION The MITRE Corporation REPORT NUMBER JASON Program Office JSR-96-325 1820 Dolley Madison Blvd McLean, Virginia 22102 9. SPONSORINGIMONITORING AGENCY NAME(S) AND ADDRESS(ES) 10. SPONSORINGIMONITORING AGENCY REPORT NUMBER DeparttnentofEnergy Wasbdngton,DC 20585 JSR-96-325 11.
    [Show full text]