DOCSLIB.ORG

Material Safety Data Sheet

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Material Safety Data Sheet MATERIAL SAFETY DATA SHEET Manufacturer: Strem Chemicals, Inc Strem Customer Service (978) 499-1600 7 Mulliken Way CHEMTREC (Emergency Only) (800) 424-9300 Newburyport, MA 01950-4098 U.S.A. Poison Center (800) 562-8236 www.strem.com Section 1: Product Identification Chemical Name: Diethylzinc, min. 95% (Material sold in non-returnable cylinder) Product Number: 93-3030 CAS Registry Number: 557-20-0 Formula: Zn(C2H5)2 EINECS Number: 209-161-3 Chemical Family: metal alkyl Synonym: zinc, diethyl Section 2: Composition and Information on Ingredients Ingredient CAS Number Percent ACGIH (TWA) OSHA (PEL) Title Compound 557-20-0 100% 5 mg/m3 (fume) 5 mg/m3 (fume) Section 3: Hazards Identification Inhalation of zinc oxide fume produced from this compound in a fire may cause metal fume fever or zinc Emergency Overview: shakes consisting of chills, fever, muscular pain, nausea, and vomiting. May cause thermal burns. Primary Routes of Exposure: Eyes, skin, and inhalation of combustion products. Eye Contact: Direct contact of liquid with the eyes will cause thermal burns and possible blindness. Skin Contact: Liquid bursts in to flame in air, causing thermal burns to skin. Fume causes burns to the nose, mucous membranes and respiratory tract causing metallic taste, dry throat, Inhalation: and chills. Ingestion: Ingestion is an unlikely mode of entry as the material is pyrophoric. Acute Health Affects: Causes burns to skin, eyes and respiratory tract. Inhalation may cause chills and nausea. No serious long-term chronic effects associated with zinc compounds. Prolonged inhalation may cause Chronic Health Affects: laryngitis. Prolonged ingestion may cause constipation. NTP: No IARC: No OSHA: No SECTION 4: First Aid Measures Immediately flush the eyes with copious amounts of water for at least 10-15 minutes. A victim may need Eye Exposure: assistance in keeping their eye lids open. Get immediate medical attention. Wash the affected area with a large volume of water applied rapidly. Remove contaminated clothes if Skin Exposure: necessary. Seek medical assistance if irritation persists. Remove the victim to fresh air. Closely monitor the victim for signs of respiratory problems, such as difficulty Inhalation: in breathing, coughing, wheezing, or pain. In such cases seek immediate medical assistance. Seek medical attention immediately. Keep the victim calm. Give the victim water (only if conscious). Induce Ingestion: vomiting only if directed by medical personnel. Page 1/3 MATERIAL SAFETY DATA SHEET Manufacturer: Strem Chemicals, Inc Strem Customer Service (978) 499-1600 7 Mulliken Way CHEMTREC (Emergency Only) (800) 424-9300 Newburyport, MA 01950-4098 U.S.A. Poison Center (800) 562-8236 www.strem.com SECTION 5: Fire Fighting Measures Flash Point: -1°F Autoignition Temperature: pyrophoric Explosion Limits: no data Extinguishing Medium: Vermiculite, sand, dry chemical. Use no water If this product is involved in a fire, fire fighters should be equipped with a NIOSH approved positive pressure Special Fire Fighting Procedures: self- contained breathing apparatus and full protective clothing. Hazardous Combustion and If involved in a fire this material may emit irritating zinc fume. Decomposion Products: Unusual Fire or Explosion Hazards: Pyrophoric material. Material will ignite spontaneously on contact with air. SECTION 6: Accidental Release Measures Material will ignite spontaneously in air. Burning material may release toxic fumes. Leave the area unless fitted Spill and Leak Procedures: with a self-contained breathing apparatus. Smother fire with dry powder. Do not use water. SECTION 7: Handling and Storage Store in a steel cylinder under dry argon or nitrogen. Transfer using metal, not plastic materials. Expect fire Handling and Storage: when disassembling used piping. Do not use flammable solvents to clean out piping. SECTION 8: Exposure Controls and Personal Protection Eye Protection: Always wear approved safety glasses when handling a chemical substance in the laboratory. Skin Protection: Wear protective clothing and gloves. consult with glove manufacturer to determine the proper type of glove. Ventilation: This product must only be handled in an efficient fume hood. If ventilation is not available a respirator should be worn. The use of respirators requires a Respirator Respirator: Protection Program to be in compliance with 29 CFR 1910.134. Ventilation: This product must only be handled in an efficient fume hood. Additional Protection: Wear full face shield, lab apron and suitable gloves. SECTION 9: Physical and Chemical Properties Color and Form: colorless liq. Molecular Weight: 123.49 Melting Point: -28°C Boiling Point: 124°C Vapor Pressure: 28mm (20°C) Specific Gravity: 1.18 Odor: metallic odor Solubility in Water: reacts vigorously with water SECTION 10: Stability and Reactivity Stability: moisture sensitive, pyrophoric Hazardous Polymerization: no hazardous polymerization Conditions to Avoid: Contact with air and moisture. Incompatibility: Water, alcohols, carbonyl compounds, mineral acids, oxidizing agents, air, and chlorinated hydrocarbons. Decomposition Products: ethane and zinc oxide. Page 2/3 MATERIAL SAFETY DATA SHEET Manufacturer: Strem Chemicals, Inc Strem Customer Service (978) 499-1600 7 Mulliken Way CHEMTREC (Emergency Only) (800) 424-9300 Newburyport, MA 01950-4098 U.S.A. Poison Center (800) 562-8236 www.strem.com SECTION 11: Toxicological Information RTECS Data: No information available in the RTECS files. Carcinogenic Effects: No data Mutagenic Effects: No data Tetratogenic Effects: No data SECTION 12: Ecological Information Ecological Information: Very toxic to aquatic organisms. May cause long-term adverse effects in the aquatic environment. SECTION 13: Disposal Considerations Disposal: Dispose of according to local, state and federal regulations. SECTION 14: Transportation Shipping Name (CFR): Organometallic substance,Liquid,Pyrophoric,Water-reactive Hazard Class (CFR): 4.2 Additional Hazard Class (CFR): 4.3 Packaging Group (CFR): I UN ID Number (CFR): UN# 3394 Shipping Name (IATA): Forbidden Hazard Class (IATA): NA Additional Hazard Class (IATA): NA Packaging Group (IATA): NA UN ID Number (IATA): UN# 3394 SECTION 15: Regulatory Information TSCA: Listed in the TSCA inventory. SARA (Title 313): Title compound: See category N982 for reporting. Second Ingredient: None Third Ingredient: None SECTION 16: Other Information The information herein is believed to be accurate and reliable as of the date compiled. However, Strem Disclaimer: Chemicals, Inc. makes no representation, warranty, or guarantee of any kind with respect to the information contained in this document or any use of the product based on this information. Preparation Date: 5/13/2002 Revision Date: 2/22/2012 Strem Chemicals, Inc. Strem Chemicals, Inc. Strem Chemicals, Inc. Strem Chemicals UK, Ltd. 7 Mulliken Way 15, rue de l'Atome, Z.I. Postfach 1215 Newton Hall Newburyport, MA 01950-4098 USA 67800 BISCHHEIM (France) 77672 KEHL (Germany) Town Street Tel: (978) 499 1600 Tel: (33) 03 88 62 52 60 Telefon: 0 78 51/ 7 58 79 Newton Fax: (978) 465 3104 Fax: (33) 03 88 62 26 81 [email protected] Cambridge, England CB22 7ZE Toll free (in USA & Canada) [email protected] Tel: 0845 643 7263 Tel: (800) 647 8736 Fax: 0845 643 7362 Fax: (800) 517 8736 [email protected] [email protected] Page 3/3.
Load more

Recommended publications
  • Efficient Asymmetric Addition of Diethylzinc to Ketones Using Tartaric Acid Derivative As Chiral Ligand
    General Papers ARKIVOC 2008 (ii) 25-32 Efficient asymmetric addition of diethylzinc to ketones using tartaric acid derivative as chiral ligand Ailing Hui,a Jintang Zhang,b Huayin Sun,b and Zhiyong Wangb* aEngineering Research Center of Bio-process (Hefei University of Techonology), Ministry of Education, 193 Tunxi Road, Hefei, Anhui 230009, PRC bDepartment of Chemistry, University of Science & Technology of China, 96 Jinzhai Road, Hefei, Anhui 230026, PRC E-mail: [email protected] Abstract A new chiral ligand derived from natural tartaric acid was synthesized and was applied to the asymmetric addition of diethylzinc to aldehyde and ketones. Moderate to good enantioselectivities were obtained in the asymmetric addition of diethylzinc to ketones with 10% mol catalyst loading at room temperature. Keywords: Tartaric acid, asymmetric addition, diethylzinc, aldehyde, ketone Introduction Chiral alcohols are ubiquitous in the structure of natural products and drug compounds, and are also important precursors for many other functional organic molecules. One of the most useful methods for the asymmetric preparation of sec-alcohols and tert-alcohols is the enantioselective addition of dialkylzinc reagents to carbonyl compounds with chiral ligands 1. Recent studies 2 showed the ligands with C2-symmetrical axes could catalyze dialkylzinc to aldehydes or ketones 3. Taking the advantage of the chirality of L-tartaric acid, we4 designed and synthesized a series of ligands with C2-symmetric axe, two of them were successfully applied to the asymmetric addition of diethylzinc to ketones. Recently, another new chiral ligands derived from L-tartaric acid were synthesized, as showed in Scheme 1. Furthermore, these ligands were employed as promoters in the addition of diethylzinc to aldehyde and ketones.
    [Show full text]
  • Chemical Name Federal P Code CAS Registry Number Acutely
    Acutely / Extremely Hazardous Waste List Federal P CAS Registry Acutely / Extremely Chemical Name Code Number Hazardous 4,7-Methano-1H-indene, 1,4,5,6,7,8,8-heptachloro-3a,4,7,7a-tetrahydro- P059 76-44-8 Acutely Hazardous 6,9-Methano-2,4,3-benzodioxathiepin, 6,7,8,9,10,10- hexachloro-1,5,5a,6,9,9a-hexahydro-, 3-oxide P050 115-29-7 Acutely Hazardous Methanimidamide, N,N-dimethyl-N'-[2-methyl-4-[[(methylamino)carbonyl]oxy]phenyl]- P197 17702-57-7 Acutely Hazardous 1-(o-Chlorophenyl)thiourea P026 5344-82-1 Acutely Hazardous 1-(o-Chlorophenyl)thiourea 5344-82-1 Extremely Hazardous 1,1,1-Trichloro-2, -bis(p-methoxyphenyl)ethane Extremely Hazardous 1,1a,2,2,3,3a,4,5,5,5a,5b,6-Dodecachlorooctahydro-1,3,4-metheno-1H-cyclobuta (cd) pentalene, Dechlorane Extremely Hazardous 1,1a,3,3a,4,5,5,5a,5b,6-Decachloro--octahydro-1,2,4-metheno-2H-cyclobuta (cd) pentalen-2- one, chlorecone Extremely Hazardous 1,1-Dimethylhydrazine 57-14-7 Extremely Hazardous 1,2,3,4,10,10-Hexachloro-6,7-epoxy-1,4,4,4a,5,6,7,8,8a-octahydro-1,4-endo-endo-5,8- dimethanonaph-thalene Extremely Hazardous 1,2,3-Propanetriol, trinitrate P081 55-63-0 Acutely Hazardous 1,2,3-Propanetriol, trinitrate 55-63-0 Extremely Hazardous 1,2,4,5,6,7,8,8-Octachloro-4,7-methano-3a,4,7,7a-tetra- hydro- indane Extremely Hazardous 1,2-Benzenediol, 4-[1-hydroxy-2-(methylamino)ethyl]- 51-43-4 Extremely Hazardous 1,2-Benzenediol, 4-[1-hydroxy-2-(methylamino)ethyl]-, P042 51-43-4 Acutely Hazardous 1,2-Dibromo-3-chloropropane 96-12-8 Extremely Hazardous 1,2-Propylenimine P067 75-55-8 Acutely Hazardous 1,2-Propylenimine 75-55-8 Extremely Hazardous 1,3,4,5,6,7,8,8-Octachloro-1,3,3a,4,7,7a-hexahydro-4,7-methanoisobenzofuran Extremely Hazardous 1,3-Dithiolane-2-carboxaldehyde, 2,4-dimethyl-, O- [(methylamino)-carbonyl]oxime 26419-73-8 Extremely Hazardous 1,3-Dithiolane-2-carboxaldehyde, 2,4-dimethyl-, O- [(methylamino)-carbonyl]oxime.
    [Show full text]
  • Chem 115 Myers
    Myers Organozinc Reagents: Asymmetric Additions to Carbonyl Compounds Chem 115 Recent Reviews: • In 1984, Oguni and Omi found that a small amount of (S)-leucinol catalyzed the enantioselective addition (49% ee) of diethylzinc to benzaldehyde. Pu, L.; Yu, H.-B. Chem. Rev. 2001, 101, 757–824. Lemire, A.; Cote, A.; Janes, M. K.; Charette, A. B. Aldrichimica Acta 2009, 42, 71–83. Lumbroso, A.; Cooke, M. L.; Breit, B. Angew. Chem. Int. Ed. 2013, 52, 1890–1932. H3C O OH OH 2 mol % NH CH3 2 CH3 H + (C2H5)2Zn Background: toluene, 20 °C, 43 h 96% yield, 49% ee • The reactivity of dialkylzinc reagents towards ketones and aldehydes is low; the rate of addition of Et2Zn to benzaldehyde is negligible at room temperature. Oguni, N.; Omi, T. Tetrahedron Lett. 1984, 25, 2823–2824. • The addition of a catalytic amount of TMEDA will promote the addition of diethylzinc at room temperature to 4-benzoylbenzaldehyde in 93% yield. • In 1986, Noyori et al. published the first highly selective procedure for the asymmetric addition of diethyl- and dimethylzinc to aldehydes employing (–)-3-exo-(dimethylamino)isoborneol (DAIB) as a chiral catalyst. O OH 5 mol % TMEDA CH3 H3C CH3 H + (C2H5)2Zn toluene, 23°C, 14 h N(CH3)3 Bz Bz 93% OH racemic H3C (–)-DAIB Soai, K.; Watanabe, M.; Koyano, M. Bull. Chem. Soc. Jpn. 1989, 25, 2124–2125. O 2 mol % (–)-DAIB OH + R' Zn • X-Ray structures of dimethylzinc and its adduct with 1,3,5-trimethylhexahydro-1,3,5-triazine 2 R H toluene, 0 °C R R' show that upon bis-complexation, dimethylzinc shifts from a linear geometry to a tetrahedral geometry and that the carbon-zinc bond length increases from 1.95 Å to 1.98 Å.
    [Show full text]
  • Atomic Layer Deposition of Zno on Mesoporous Silica: Insights Into Growth Behavior of Zno Via In-Situ Thermogravimetric Analysis
    nanomaterials Article Atomic Layer Deposition of ZnO on Mesoporous Silica: Insights into Growth Behavior of ZnO via In-Situ Thermogravimetric Analysis Piyush Ingale 1 , Kristian Knemeyer 1, Mar Piernavieja Hermida 1, Raoul Naumann d’Alnoncourt 1,* , Arne Thomas 2 and Frank Rosowski 1,3 1 BasCat—UniCat BASF JointLab, Technische Universität Berlin, Hardenbergstraße 36, 10623 Berlin, Germany; [email protected] (P.I.); [email protected] (K.K.); [email protected] (M.P.H.); [email protected] (F.R.) 2 Institut für Chemie, Technische Universität Berlin, 10623 Berlin, Germany; [email protected] 3 Process Research and Chemical Engineering, BASF SE, 67056 Ludwigshafen, Germany * Correspondence: [email protected] Received: 28 April 2020; Accepted: 19 May 2020; Published: 20 May 2020 Abstract: ZnO is a remarkable material with many applications in electronics and catalysis. Atomic layer deposition (ALD) of ZnO on flat substrates is an industrially applied and well-known process. Various studies describe the growth of ZnO layers on flat substrates. However, the growth characteristics and reaction mechanisms of atomic layer deposition of ZnO on mesoporous powders have not been well studied. This study investigates the ZnO ALD process based on diethylzinc (DEZn) and water with silica powder as substrate. In-situ thermogravimetric analysis gives direct access to the growth rates and reaction mechanisms of this process. Ex-situ analytics, e.g., N2 sorption analysis, XRD, XRF, HRTEM, and STEM-EDX mapping, confirm deposition of homogenous and thin films of ZnO on SiO2. In summary, this study offers new insights into the fundamentals of an ALD process on high surface area powders.
    [Show full text]
  • A New Look at the Reactivity of TEMPO Toward Diethylzinc Krzysztof Budny-Godlewski,† Dominik Kubicki,† Iwona Justyniak,‡ and Janusz Lewinskí *,†,‡
    Communication pubs.acs.org/Organometallics A New Look at the Reactivity of TEMPO toward Diethylzinc Krzysztof Budny-Godlewski,† Dominik Kubicki,† Iwona Justyniak,‡ and Janusz Lewinskí *,†,‡ † Faculty of Chemistry, Warsaw University of Technology, Noakowskiego 3, 00-664 Warsaw, Poland ‡ Institute of Physical Chemistry, Polish Academy of Sciences, Kasprzaka 44/52, 01-224 Warsaw, Poland *S Supporting Information ABSTRACT: Reactions of diethylzinc with TEMPO were investigated. − ° Dropwise addition of 1 equiv of TEMPO to Et2Zn at 10 C leads to the nitroxide complex EtZn(TEMPO) in high yield, whereas upon addition of 2 equiv of TEMPO the corresponding homoleptic nitroxide ff compound Zn(TEMPO)2 is formed. Di usion ordered NMR spectros- copy experiments revealed that both zinc nitroxide compounds exist in monomeric forms in solution, while single-crystal X-ray diffraction confirmed their dimeric structure in the solid state. he stable nitroxyl radical TEMPO (2,2,6,6-tetramethylpi- to confirm the radical mechanism of this process. Incidentally, peridinyl oxide) was first synthesized in 19591 and since the formation of a small amount of the isolable dimeric T μ that time has attracted widespread interest. It has been widely complex [EtZn( 2-TEMPO)]2 was observed. The authors also 2 used in polymer synthesis and catalytic organic reactions. noted that the reaction of TEMPO with Et2Zn does not occur η5 6 Much attention has also been paid to its application as a ligand unless ( -C5Me5)2Zn is present in the reaction system. or radical trapping agent in reactions with metal complexes.3,4 Recently, TEMPO has also been used as a reagent in various The latter studies have demonstrated that TEMPO is a very other transformations involving group 2 organometallics.
    [Show full text]
  • Acutely / Extremely Hazardous Waste List
    Acutely / Extremely Hazardous Waste List Federal P CAS Registry Acutely / Extremely Chemical Name Code Number Hazardous 4,7-Methano-1H-indene, 1,4,5,6,7,8,8-heptachloro-3a,4,7,7a-tetrahydro- P059 76-44-8 Acutely Hazardous 6,9-Methano-2,4,3-benzodioxathiepin, 6,7,8,9,10,10- hexachloro-1,5,5a,6,9,9a-hexahydro-, 3-oxide P050 115-29-7 Acutely Hazardous Methanimidamide, N,N-dimethyl-N'-[2-methyl-4-[[(methylamino)carbonyl]oxy]phenyl]- P197 17702-57-7 Acutely Hazardous 1-(o-Chlorophenyl)thiourea P026 5344-82-1 Acutely Hazardous 1-(o-Chlorophenyl)thiourea 5344-82-1 Extemely Hazardous 1,1,1-Trichloro-2, -bis(p-methoxyphenyl)ethane Extemely Hazardous 1,1a,2,2,3,3a,4,5,5,5a,5b,6-Dodecachlorooctahydro-1,3,4-metheno-1H-cyclobuta (cd) pentalene, Dechlorane Extemely Hazardous 1,1a,3,3a,4,5,5,5a,5b,6-Decachloro--octahydro-1,2,4-metheno-2H-cyclobuta (cd) pentalen-2- one, chlorecone Extemely Hazardous 1,1-Dimethylhydrazine 57-14-7 Extemely Hazardous 1,2,3,4,10,10-Hexachloro-6,7-epoxy-1,4,4,4a,5,6,7,8,8a-octahydro-1,4-endo-endo-5,8- dimethanonaph-thalene Extemely Hazardous 1,2,3-Propanetriol, trinitrate P081 55-63-0 Acutely Hazardous 1,2,3-Propanetriol, trinitrate 55-63-0 Extemely Hazardous 1,2,4,5,6,7,8,8-Octachloro-4,7-methano-3a,4,7,7a-tetra- hydro- indane Extemely Hazardous 1,2-Benzenediol, 4-[1-hydroxy-2-(methylamino)ethyl]- 51-43-4 Extemely Hazardous 1,2-Benzenediol, 4-[1-hydroxy-2-(methylamino)ethyl]-, P042 51-43-4 Acutely Hazardous 1,2-Dibromo-3-chloropropane 96-12-8 Extemely Hazardous 1,2-Propylenimine P067 75-55-8 Acutely Hazardous 1,2-Propylenimine 75-55-8 Extemely Hazardous 1,3,4,5,6,7,8,8-Octachloro-1,3,3a,4,7,7a-hexahydro-4,7-methanoisobenzofuran Extemely Hazardous 1,3-Dithiolane-2-carboxaldehyde, 2,4-dimethyl-, O- [(methylamino)-carbonyl]oxime 26419-73-8 Extemely Hazardous 1,3-Dithiolane-2-carboxaldehyde, 2,4-dimethyl-, O- [(methylamino)-carbonyl]oxime.
    [Show full text]
  • University of Groningen Acetals of 1-Aryl-2,2-Dimethyl-1,3
    University of Groningen Acetals of 1-aryl-2,2-dimethyl-1,3-propanediols synthesis and use as chiral auxiliary Ebens, Rijko Hendrik Ebe IMPORTANT NOTE: You are advised to consult the publisher's version (publisher's PDF) if you wish to cite from it. Please check the document version below. Document Version Publisher's PDF, also known as Version of record Publication date: 1993 Link to publication in University of Groningen/UMCG research database Citation for published version (APA): Ebens, R. H. E. (1993). Acetals of 1-aryl-2,2-dimethyl-1,3-propanediols synthesis and use as chiral auxiliary. s.n. Copyright Other than for strictly personal use, it is not permitted to download or to forward/distribute the text or part of it without the consent of the author(s) and/or copyright holder(s), unless the work is under an open content license (like Creative Commons). The publication may also be distributed here under the terms of Article 25fa of the Dutch Copyright Act, indicated by the “Taverne” license. More information can be found on the University of Groningen website: https://www.rug.nl/library/open-access/self-archiving-pure/taverne- amendment. Take-down policy If you believe that this document breaches copyright please contact us providing details, and we will remove access to the work immediately and investigate your claim. Downloaded from the University of Groningen/UMCG research database (Pure): http://www.rug.nl/research/portal. For technical reasons the number of authors shown on this cover page is limited to 10 maximum. Download date: 06-10-2021 Chapter 4 ASYMMETRIC CYCLOPROPANATION 4.1 INTRODUCTION This chapter deals with asymmetric cyclopropanations of Zalkenyl acetals 2.19.
    [Show full text]
  • Chemical Reaction-Transport Model of Oxidized Diethylzinc Based on Quantum Mechanics and Cite This: RSC Adv.,2018,8, 1116 Computational fluid Dynamics Approaches†
    RSC Advances PAPER View Article Online View Journal | View Issue Chemical reaction-transport model of oxidized diethylzinc based on quantum mechanics and Cite this: RSC Adv.,2018,8, 1116 computational fluid dynamics approaches† Jian Li,a Hanlin Gan, b Yifeng Xu,a Chaoyang Wang,b Feng Long Gu *b and Gang Wang *ac We developed and studied a chemical reaction-transport model for the production of zinc oxide (ZnO) with diethylzinc (DEZn) and oxygen (O2). It was confirmed that a large number of ZnO particles were generated during the growth process by testing the internal particles of the cavity by X-ray diffraction. The formation of Zn3O3 in the gas phase reaction was simulated using density functional theory, and the effect of nucleation and formation of nanoparticles on the growth of the films was revealed. We also speculate that the adsorption of Zn-containing gas on the wall is the main route by which a ZnO film is formed. The mechanism calculated by quantum chemistry was applied in computational fluid dynamics (CFD) Creative Commons Attribution 3.0 Unported Licence. simulations using Fluent14.0 software, and the concentration distribution and gas reaction path of the reaction chamber were calculated and analyzed. Finally, a 9 gas phase reaction model and an 8 surface reaction model were established. Together with the transport model, a complete chemical reaction- transport reaction model was constructed for the ZnO–MOCVD cavity. The validity of the model was Received 19th October 2017 verified, and the optimum temperature range of DEZn and oxygen-stabilized growth of ZnO films was Accepted 15th December 2017 determined to be 673–873 K.
    [Show full text]
  • Synthesis of Poly(Hydroxyalkanoates
    SYNTHESIS OF POLY(HYDROXYALKANOATES): ROUTES TO POLY(3- HYDROXYBUTYRATE) AND POLY(3-HYDROXYPROPIONATE) FROM THE CARBONYLATION AND RING-OPENING POLYMERIZATION OF EPOXIDES A Dissertation Presented to the Faculty of the Graduate School of Cornell University In Partial Fulfillment of the Requirements for the Degree of Doctor of Philosophy by Erin Whitfield Dunn August 2012 © 2012 Erin Whitfield Dunn SYNTHESIS OF POLY(HYDROXYALKANOATES): ROUTES TO POLY(3- HYDROXYBUTYRATE) AND POLY(3-HYDROXYPROPIONATE) FROM THE CARBONYLATION AND RING-OPENING POLYMERIZATION OF EPOXIDES Erin Whitfield Dunn, Ph.D. Cornell University 2012 New methods for the syntheses of poly(3-hydroxybutyrate) (P3HB) and poly(3-hydroxypropionate) (P3HP) from epoxides are reported. Epoxides are readily available, inexpensive starting materials that can be transformed into valuable biodegradable and biocompatible polyesters. We successfully developed a one-pot synthesis of P3HB from propylene oxide and carbon monoxide using a multicatalytic transformation. The intermediate !-butyrolactone was formed and subsequently polymerized in situ. The carbonylation of propylene oxide to !-butyrolactone was + - accomplished using a catalyst of the form [Lewis acid] [Co(CO)4] , and the lactone monomer was then polymerized by a (BDI)ZnOAc (BDI = !-diiminate) catalyst. The two catalysts were found to have orthogonal reactivity, and were compatible with each other as well as with the solvent, substrate, and any reaction side-products. The reaction proceeded with high activity and selectivity to synthesize P3HB with high molecular weights. Furthermore, this dual-catalyst approach eliminated exposure to the toxic !-butyrolactone monomer. We also report the synthesis of P3HP from ethylene oxide and carbon monoxide. The carbonylation of ethylene oxide proceeded in greater than 99% yield + - and high selectivity with the bimetallic catalyst [(ClTPP)Al(THF)2] [Co(CO)4] (ClTPP = meso-tetra(4-chlorophenyl)porphyrinato; THF = tetrahydrofuran).
    [Show full text]
  • Diethylzinc (Dez) 1
    Akzo Nobel Polymer Chemicals LLC MATERIAL SAFETY DATA SHEET DIETHYLZINC (DEZ) 1. CHEMICAL PRODUCT AND COMPANY INFORMATION Product name Chemical description DIETHYLZINC (DEZ) Diethylzinc Synonym Chemical formula DEZ C4 H10 Zn CAS number Chemical family 557-20-0 Zinc alkyls Supplier Akzo Nobel Polymer Chemicals LLC 300 South Riverside Plaza Chicago, IL 60606 USA Medical/Handling Emergency Transportation Emergency + 1-914-693-6946 CHEMTREC - USA: 1-800-424-9300 Dobbs Ferry, NY USA CANUTEC - CANADA: 1-613-996-6666 Product use Product/technical Information Semiconductors 1-800-828-7929 Date of first issue Date of last issue / Revision # 03-02-1995 08-26-1999 / 8.00 2. COMPOSITION/INFORMATION ON INGREDIENTS Ingredient Percentage(s) CAS number Diethylzinc 99.00 - 100.00 557-20-0 3. HAZARDS IDENTIFICATION Emergency overview Clear, colorless liquid. DANGER! EXTREMELY FLAMMABLE. CATCHES FIRE IF EXPOSED TO AIR. CAUSES SKIN AND EYE BURNS. REACTS VIOLENTLY WITH WATER. Metal alkyls are pyrophoric. The metal alkyl reacts spontaneously with air and/or moisture resulting in ignition. In case of fire, reignition of the metal alkyl may occur after the fire has been extinguished. Health effects Skin and eye contact are the primary routes of exposure to this product. Inhalation of the metal alkyl in this product is unlikely due to the highly reactive nature of the metal alkyl with air and its low vapor pressure. This material will react with moisture in or on the skin to produce thermal and chemical burns. This product will react with moisture in the eyes to produce severe chemical and thermal burns. Ingestion will result in burning of the mouth, throat and any part of the gastrointestinal system with which the material comes in contact.
    [Show full text]
  • OMZN018 GHS US English US
    OMZN018 - DIETHYLZINC, 1M in heptane DIETHYLZINC, 1M in heptane Safety Data Sheet OMZN018 Date of issue: 11/20/2017 Revision date: 03/14/2018 Version: 1.1 SECTION 1: Identification 1.1. Identification Product name : DIETHYLZINC, 1M in heptane Product code : OMZN018 Product form : Mixture Physical state : Liquid Formula : C4H10Zn Synonyms : ZINC ETHYL Chemical family : METAL ALKYL IN SOLVENT 1.2. Recommended use and restrictions on use Recommended use : Chemical intermediate 1.3. Supplier GELEST, INC. 11 East Steel Road Morrisville, PA 19067 USA T 215-547-1015 - F 215-547-2484 - (M-F): 8:00 AM - 5:30 PM EST [email protected] - www.gelest.com 1.4. Emergency telephone number Emergency number : CHEMTREC: 1-800-424-9300 (USA); +1 703-527-3887 (International) SECTION 2: Hazard(s) identification 2.1. Classification of the substance or mixture GHS-US classification Flammable liquids Category 2 H225 Highly flammable liquid and vapor Substances and mixtures which in contact with water emit flammable H260 In contact with water releases flammable gases which may ignite gases Category 1 spontaneously Skin corrosion/irritation Category 1B H314 Causes severe skin burns and eye damage Serious eye damage/eye irritation Category 1 H318 Causes serious eye damage Specific target organ toxicity (single exposure) Category 3 H336 May cause drowsiness or dizziness Hazardous to the aquatic environment - Acute Hazard Category 1 H400 Very toxic to aquatic life Hazardous to the aquatic environment - Chronic Hazard Category 1 H410 Very toxic to aquatic life with long
    [Show full text]
  • Download (6MB)
    STUDIES ON THE GENERATION AND REACTIVITY OF METAL CARBENOIDS A Thesis Presented by Rehan Aqil In Partial Fulfilment of the Requirements for the Award of the Degree of DOCTOR OF PHILOSOPHY OF THE UNIVERSITY OF LONDON Christopher Ingold Laboratories Department of Chemistry University of London London WCIH OAJ September 2002 ProQuest Number: U643094 All rights reserved INFORMATION TO ALL USERS The quality of this reproduction is dependent upon the quality of the copy submitted. In the unlikely event that the author did not send a complete manuscript and there are missing pages, these will be noted. Also, if material had to be removed, a note will indicate the deletion. uest. ProQuest U643094 Published by ProQuest LLC(2015). Copyright of the Dissertation is held by the Author. All rights reserved. This work is protected against unauthorized copying under Title 17, United States Code. Microform Edition © ProQuest LLC. ProQuest LLC 789 East Eisenhower Parkway P.O. Box 1346 Ann Arbor, Ml 48106-1346 Abstract ABSTRACT This thesis concerns the generation of metal carbenoids, in particular organozinc carbenoids, and their subsequent reactions, such as C-H insertion reactions or cyclopropanation with alkenes. The thesis is divided into three major sections. The introductory chapter presents a comparative review covering metal carbenoid species. The review focuses on how their reactivity is controlled by the metal, the leaving group and by the nature of electron-donating and -withdrawing groups on the carbenoid and finally which type of alkenes give the highest reactivity and yields as a function of these parameters. The results and discussion chapter opens with a brief overview of the organozinc carbenoid chemistry which has been developed within our group.
    [Show full text]