#8017 Gloss #8010,Satin#8012 Levels: Sheen coat dura ahighly Dries to Finish: Composition: stains. and spills against protects and durability, superior has drying, fast is product This wood. orfinished varnished previously or stained onbare, Use and cabinets. furniture doors, floors, including surfaces wood exterior protected and For interior finish. clear a beautiful, with wood grain natural the enhances apply polyurethane easy-to- This stains. and spills scratches, nicks, from surfaces wood interior to protect formulated finish ultra-durable Polyurethane Interior Cabot Oil-modified urethane urethane Oil-modified Recommended Uses: Uses: Recommended

ble, protective clear and Semi-Gloss #8010Gloss, #8012Satin ὑSemi-Gloss INTERIOR OIL-BASEDPOLYURETHANE is an

only. surfaces For interior this productadjacentto add colorant to this product. Do not apply over wetordamp surfaces. Do not thin or belo temperature is SEALERS. STEARATES, SUCH ASSANDING USE OVERPRODUCTSTHATCONTAIN DONOT ON FLOORAPPLICATIONS, Restrictions: containers. Available in 1/2pint, quart and gallon Packaging/Containers: (46–60 m Approximately 500–650sq.ft./gal. Coverage/Thinning: Do nottintor intermix withotherproducts. porosity. porosity. Tinting/Intermixing: Tinting/Intermixing: ² ) depending upon surface upon ) depending Do not apply when air or surface w 50°F.Donotapply cementorstucco.

sealed surfaces 1-888-345-5732 Emergency MedicalTelephone: ventilation. by opening allwindows and doors for cross vapors of Preventbuildup gone. are vapors all until use and during ignition of sources and other lights pilot motors, electric heaters, open flameand lit cigarettes. Turn off stoves, DO NOTSMOKE. DISTILLATES. COMBUSTIBLE: DANGER: CONTAINSPETROLEUM COMBUSTIBLE LIQUID&VAPOR. WARNING! VAPORHARMFUL. rulings. currentV.O.C. to pertaining information additional for &Support Services Technical Cabot’s Call current regulations. for Specialty Architectural Coatings under (Volatile OrganicCo Impact: These products arein compliance with V.O.C. Environmental closed original containers Life: Shelf Thickness: Film Point: Flash Weight: Data: Chemical and Physical Disposal: and Clean-up available upon request. Material Safety Data Sheets (MSDS) are regulations. Close container when not in use. accordance with local, state and federal in portion unused empty or of cans Dispose regulations. tolocal according filled metal container anddisposeof wool or waste in asealed, water- after each use, place rags, steel improperly discarded.Immediately if fire catch spontaneously soaked with this product may DANGER: Rags,steelwoolorwaste spirits. mineral with equipment Water Repellent: Water 7.50–7.60 pounds per gallon 7.50–7.60pounds Aminimum offive(5)years in 101°F (38°C) 0.8–1.0 milspercoaton Yes Yes mpounds) requirements Keep away from sparks, Clean brushes and brushesand Clean

TECHNICAL DATA INTERIOR OIL-BASED POLYURETHANE #8010 SERIES

INTERIOR OIL-BASED POLYURETHANE #8010 Gloss, #8012 Satin & #8017 Semi-Gloss

% Solids (weight): 50–51 Application:

% Solids (volume): 38–39 DO NOT SHAKE! Stir well before using, If this product does not perform as stated on % Pigment (weight): 0–3 Check effect on extra wood or hidden area. the label after you apply it according to label Apply a uniform, thin coat using a high- directions, Cabot will either replace this Viscosity: 120–220 cps. quality natural bristle brush. Allow to dry product or refund its purchase price, at its Pigment Type: Precipitated Silica overnight before applying additional coats. option. Cabot disclaims all other implied or Vehicle Type: Oil-modified urethane For best results, apply two thin expressed warranties. Cabot will not provide Solvent Type: Aliphatic & Aromatic coats. or pay for labor for removal or application of the product. This warranty excludes all Hydrocarbons Stir thoroughly before and occasionally while incidental or consequential damages. This using. If using multiple containers, blend V.O.C. Content: GPL Maximum of 450 warranty gives you specific legal rights, and together to ensure consistency. Before grams/liter (3.75 pounds/gal.) you may have other rights which vary from application, wipe surface with a tack cloth to state to state. remove dust. Avoid creating airborne dust for 24 hours after applying final coat. Apply using a Surface Preparation: high-quality natural bristle brush. Apply with General: Clean and dry surface thoroughly. lambswool or synthetic pad to wood floors, Minimal because Cabot Interior Polyurethane Remove all dirt, dust, wax and wood marks. always maintain a wet edge to avoid lap marks. provides a tough abrasion and water- Do not apply over lacquer or shellac. Allow to dry for a minimum of 8 hours before resistant finish. Floors and countertops New or Stained Wood: Smooth wood lightly recoating. After applying initial coat of this subject to heavy traffic and use may require with sandpaper. Stain, if desired, and sand product, sand with fine sandpaper and wipe more maintenance. lightly again. Remove sanding dust before with tack cloth. For best results on new surfaces finishing. and wood floors, apply two thin coats. Avoid heavy traffic for 72 hours after final application, Painted or Varnished Wood: Remove all paint For additional technical information, product do not install carpeting or expose to cleaning and varnish in poor condition with sandpaper line color cards, fan decks and liquid product products for 7 days. or paint and varnish remover following samples, see your specialized Cabot Dealer manufacturer’s instructions. Drying Time: or call the Cabot WoodCare Specialists in Technical Services & Support toll-free at WARNING! If you scrape, sand or Dries in 4–6 hours, wait overnight before 1-800-US-STAIN. remove old paint from any surface, recoating. Dry times are longer in high you may release lead dust. LEAD IS humidity or cool temperatures. Apply only TOXIC. EXPOSURE TO LEAD DUST when surface and air temperatures are CAN CAUSE SERIOUS ILLNESS, SUCH between 50–90 °F (10–32 °C) during For complete model specifications and AS BRAIN DAMAGE, ESPECIALLY IN application and drying time. technical data on all Cabot products, visit the Cabot Home Page at cabotstain.com. CHILDREN. PREGNANT WOMEN Number of Coats: For best results on new SHOULD ALSO AVOID EXPOSURE. surfaces and wood floors, apply 2 thin coats. Wear a NIOSH-approved respirator to control lead exposure. Clean up carefully with a wet mop or HEPA Cabot WoodCare Products are sold vacuum. Before you start, find out throughout the United States and Canada. how to protect yourself and your For a list of Cabot dealer locations, please family by contacting the USEPA/Lead ® contact Cabot’s Technical Services & Support Cabot Information Hotline at 1-800-424- at 1-800-US-STAIN. Newburyport, MA 01950 LEAD (5323) or visit Tel.: 1-800-US-STAIN www.epa.gov/lead. Fax: 1-800-998-3299 cabotstain.com

#8010– updated 7/09