Hellenic Accreditation System

Annex F1/12 to the Certificate No. 124-5 SCOPE of ACCREDITATION of the Testing Laboratory of A.T.O.M. DYNAMIC S.A.

Materials / Products to be Types of test / Properties to be Applied Methods / Techniques to be used tested measured Non-destructive tests using magnetic particles

Welds of ferromagnetic Magnetic particle testing by the ΕΝ ISO 17638: 2009 materials use of yoke (visible light) Non-Destructive examination of Welds- Magnetic particle examination of welds Ferromagnetic materials, ASME: 2013 Boiler and Pressure Vessel parts and fabrications, Code. including weldings Section V, Non destructive examination. Article 7 : Magnetic particle examination

ASTM E1444/E1444M-12 Standard practice for magnetic particle examination

ASTM E709-15 Standard practice for magnetic particle examination Ferromagnetic steel BS EN 10228-1: 1999 forgings Non-destructive testing of steel forgings- Part 1: Magnetic particle inspection

Ferromagnetic cast BS EN 1369: 2012 products Founding- Magnetic particle inspection

Non-destructive tests using penetrant fluids

Page 1 of 4 Annex F1/12 to the Certificate ESYD No.124-5 03.09.2015 Materials / Products to be Types of test / Properties to be Applied Methods / Techniques to be used tested measured Non Porous Materials, On Site Penetrant Testing EN ISO 3452-1: 2013 Parts and Fabrications, (visible light) Non-Destructive Testing- Penetrant Testing- including Weldings Part 1: General Principles ASTM E1417/E1417M-13 Standard Practice for Liquid Penetrant Examination ASTM E 165/ E 165Μ: 2012 Standard Practice for Liquid Penetrant Examination for General Industry ASME: 2013 Boiler and Pressure Vessel Welds of Metallic Code. Section V, Non Destructive Materials Examination. Article 6 : Liquid Penetrant Examination Steel Forgings BS EN 10228-2:1998 Non-Destructive Testing of Steel Forgings- Part 2: Penetrant Testing Metallic Cast Products BS EN 1371-1:2011 Founding. Liquid Penetrant Inspection. Part 1: Sand, gravity die and low pressure die castings

Ultrasonic non-destructive tests

Welds of Metallic Ultrasonic testing EN ISO 16810: 2014 Materials Non-Destructive Testing-Ultrasonic Examination-Part 1: General Principles EN ISO 17640: 2010 Non-Destructive Examination of Welds- Ultrasonic Examination - Techniques, testing levels and assessment ASME : 2013 Boiler and Pressure Vessel Code. Section V, Non Destructive Examination Article 4 : In Service Inspection Article 5 : Inspection of Materials and Fabrications

Welds of Metallic Ultrasonic testing. Use of time– EN ISO 10863: 2011 Materials of-flight diffraction technique Non-Destructive Testing of welds. Ultrasonic. (ToFD) Use of time–of-flight diffraction technique (ToFD) Metallic Plates Ultrasonic Thickness ASTM E 797/E797M: 2010 Measurement Standard Practice for Measuring Thickness by Thickness range (1-100)mm Manual Ultrasonic Pulse-Echo Contact Method

Radiographic non destructive tests

Metallic Materials, Radiography Testing, using –X EN ISO 5579: 2013

Page 2 of 4 Annex F1/12 to the Certificate ESYD No.124-5 03.09.2015 Materials / Products to be Types of test / Properties to be Applied Methods / Techniques to be used tested measured Products and Fabrications & -γ rays Non Destructive Testing - Radiographic including Weldings (Ir192 & Se 75) Examination of Metallic Materials using film techniquesand X- or gamma-rays. General Rules ASME : 2013 Boiler and Pressure Vessel Code. Section V, Non Destructive Examination. Article 2 : Radiographic Examination

ASTM E 94: 2004 (2010) Standard Guide for Radiographic Examination Welds of Metallic ASTM E 1032: 2012 Materials Standard Test Method for Radiographic Examination of Weldings EN ISO 17636-1: 2013 Non Destructive Testing - Radiographic testing Part 1: X- and gamma-ray techniques with film

EN ISO 17636-2: 2013 Non Destructive Testing of welds – radiographic testing – Part 2: X- and gamma-ray techniques with digital detectors

Mechanical tests

Welds, Tensile test (Proof Strength not ASME IX: 2013 – QW 150 Plates included). Ultimate tensile strength EN ISO 6892-1 : 2009 Yield point EN ISO 4136: 2012 Elongation API 1104: 21ST EDITION Welds, Macrography ASME IX: 2013 – QW 183, QW 184 Plates (detection of discontinuities by EN ISO 17639 : 2013 visual inspection) PD CEN ISO/TR 16060:2014

Fillet welds Fracture test ASME IX: 2013 – QW 182 EN ISO 9017 : 2013 (detection of discontinuities by EN ISO 9606-1: 2013 visual inspection) API 1104: 21ST EDITION

Welds, Bending ASME IX: 2013 – QW 161, QW 162 Plates (detection of discontinuities by ΕΛΟΤ EN ISO 5173:2011+A1:2012 visual inspection) API 1104: 21ST EDITION

Welds, Impact Test - Charpy ΕΝ ISO 9016:2012 Plates ΕΝ ISO 148-1:2010 ASTM E23-12c Metallic materials Portable Hardness Testing by ASTM A 1038-13 the UCI Method

Site of assessment: Permanent laboratory premises, Patima, GR-196 00 Mandra, Attiki, Greece. Approved signatories: Pan. Golfinopoulos.

Page 3 of 4 Annex F1/12 to the Certificate ESYD No.124-5 03.09.2015 This Scope of Accreditation replaces the previous one dated March 26th, 2015. The Accreditation Certificate No. 124-5, to ELOT EN ISO/IEC 17025: 2005, is valid until 5.3.2019.

Athens, September 3rd , 2015

Ioannis Sitaras Director of the Laboratories Acreditation Division

Page 4 of 4 Annex F1/12 to the Certificate ESYD No.124-5 03.09.2015