INTERLAM CORPORATION –ARCHITECTURAL METALS DIVISION SECTION 05700 ORNAMENTAL METAL SCREENS

PART 1 GENERAL

1 SECTION INCLUDES

1.A. Perforated / Laser cut Sheet Metal screens.

2 RELATED SECTIONS

2.A. Section 05500 - Metal Fabrications.

2.B. Section 06400 - Architectural Woodwork.

2.C. Section 08100 - Metal Door Frames.

2.D. Section 08710 - Door Hardware.

2.E. Section 09260 - Gypsum Board Systems.

2.F. Section 15800 - Air Distribution.

3 SUBMITTALS

3.A. Submit under provisions of Section 01300.

3.B. Product Data: Manufacturer's data sheets on each product to be used, including: 3.B.1. Preparation instructions and recommendations. 3.B.2. Storage and handling requirements and recommendations. 3.B.3. Installation methods.

3.C. Shop Drawings: Submit the following: 3.C.1. Full size templates for products requiring templates for fabrication. 3.C.2. Drawings indicating locations of products of this section in project. 3.C.3. Drawings and details indicating sizes, materials and thicknesses, fabrication and installation techniques, provisions for reinforcement and anchoring.

4 DELIVERY, STORAGE, AND HANDLING

4.A. Packing, Shipping, Handling and Unloading: Pack products of this section to prevent damage to products and finishes.

4.B. Storage and Protection: 4.B.1. Store products in manufacturer's unopened packaging until installation. 4.B.2. Maintain dry, heated storage area for products until installation.

5 SEQUENCING

5.A. Ensure that locating templates and other information required for installation of products of this section are furnished to affected trades in time to prevent interruption of construction progress.

5.B. Ensure that products of this section are supplied to affected trades in time to prevent interruption of construction progress.

6 SCHEDULING

6.A. Supply full size templates for products requiring templates for fabrication to manufacturer of products of this section in time for scheduled fabrication.

PART 2 PRODUCTS

05700-1 7 MANUFACTURERS

7.A. Acceptable Manufacturer: Interlam Corporation located at 391 Hickory St. Mount Airy, NC 27030. 336-786-6254. Contact Josh Leftwich [email protected]

7.B. http://www.interlam-design.com/architectural-metal-screens.html for pattern selection.

8 PRODUCTS

8.A. Perforated / laser cut Sheet Metal screens per pattern indicated or submitted custom design: 8.A.1. Material: 8.A.1.a. 10 GA HRPO STEEL .1270 MIN THICKNESS. HOT ROLLED PICKLED AND OILED PER ASTM A1011/ CS-B/ rev. 2015. Mill test EN 10204 3.1 8.A.2. Fastening Devices: To be determined. Stand offs, direct screw, captured frame. 8.A.3. Perforated / laser cut Sheet Metal screen Size: ______height by ______width. 8.A.4. Finish: 8.A.4.a. Steel: 8.A.4.a.1) Powder Coat Colors (As selected by Architect).

PART 3 EXECUTION

9 EXAMINATION

9.A. Do not begin installation until substrates have been properly prepared.

9.B. Verify openings and substrates are prepared to receive products of this section.

9.C. If substrate preparation is the responsibility of another installer, notify Architect of unsatisfactory preparation before proceeding.

10 PREPARATION

10.A. Clean surfaces thoroughly prior to installation.

10.B. Prepare surfaces using the methods recommended by the manufacturer for achieving the best result for the substrate under the project conditions.

11 INSTALLATION

11.A. Install in accordance with the manufacturers recommendations and the approved shop drawings.

11.B. Where appropriate, supply products of this section for installation by installers of products of other sections.

12 PROTECTION

12.A. Protect installed products until completion of project.

12.B. Replace damaged products before Substantial Completion.

13 SCHEDULES

13.A. : 13.A.1. 13.A.2. 13.A.3.

13.B. : 13.B.1. 13.B.2. 13.B.3.

05700-2 END OF SECTION

05700-3