National Emission Standards for Hazardous Air Pollutants

Collision Repair Environmental Training National Emission Standards for Hazardous Air Pollutants 40 CFR Part 63, Subpart HHHHHH Examination

1. This air regulation was developed by which of the following federal agencies?

a. OSHA – Occupational Safety and Health Administration

b. EPA – Environmental Protection Agency

c. BOA – Bureau of Air

d. USDA – United States Department of Agriculture

2. This regulation is referred to as which of the following:

a. Paint stripping and miscellaneous surface-coating operations at area sources

b. The “6H” rule

c. The “auto body” rule

d. All of the above

3. The national emission standards for hazardous air pollutants (NESHAPs) regulate two categories of sources that emit air pollution. Which of the following two are they?

a. Area sources

b. Hazardous air pollutant (HAP) sources

c. Major sources

d. The “urban dirty thirty”

4. Which of the following chemicals in autobody paint is not of concern (or targeted) for this HAP regulation? www.sbeap.org 1-800-578-8898 a. Cadmi c. Cobalt um d. Lead b. Chrom ium e. Manganese

f. Nickel

5. The collision repair shop will need to meet these air regulations if any paint used has one or more of the targeted HAPs and the paint is applied using which of the following methods?

a. Powder coating

b. Hand-held, non-refillable aerosol containers

c. Spray-apply

d. All of the above

www.sbeap.org 1-800-578-8898 6. If spray-applied paint does not contain any of the five targeted metals, then an owner or operator of a collision repair shop may petition EPA for ______from the 6H rule.

a. A certification

b. A pass

c. An exemption

d. None of the above

7. Touch-up jobs, using paint containing any of the targeted metals, do not have to follow this rule if touch up is performed using a hand-held device with a cup capacity less than or equal to ____ fluid ounces.

8. Paint-booth filters must have what percent collection or capture efficiency?

a. 88%

b. 95%

c. 98%

d. 100%

9. This capture efficiency information can be obtained from whom?

a. The filter sales representative

b. The manufacturer

www.sbeap.org 1-800-578-8898 c. Both of the above

d. Neither of the above

10. When painting an entire vehicle, booths and prep stations must have a full roof and how many walls or side curtains?

11. When painting vehicle parts, booths and prep stations must have a full roof and how many walls or side curtains?

12. When painting vehicle parts, booths must be ventilated such that air is drawn in what direction?

a. Into the booth

b. Away from the booth

c. Across the booth

13. Spray-applied coatings must be applied with which one of the following gun technologies? www.sbeap.org 1-800-578-8898 a. High volume, low pressure

b. Electrostatic

c. Airless

d. Air-assisted airless

e. Any of the above

14. The ultimate goal of gun cleaning with regard to the 6H rule is to prevent creating which of the following?

a. Hazardous waste

b. An atomized mist

c. Wastewater

15. Which is an acceptable option for cleaning spray guns?

a. Hand cleaning a disassembled gun

b. Flush gun with solvent, without spraying

c. Use fully enclosed gun washer

d. All of the above

16. To comply with this regulation, who must certify that painters have completed training in proper spray application, setup, and maintenance of spray equipment?

a. The collision repair instructor at your school

b. The owner or operator of a body shop

c. The paint supplier that hosted a training www.sbeap.org 1-800-578-8898 d. The EPA

17. All painters who spray-apply coatings with the targeted metals must be trained within how many days of their hire date?

c. 120

d. 180

18. Following the initial training date, how often must a painter receive refresher training?

a. Annually

b. Every three years c. Every five years d. Every 10 years

19. The training program is required to have certain elements. Which of the following is NOT an element of the training requirements?

a. Spray gun equipment selection, setup, and operation

b. Best spray technique for different types of coatings to improve transfer efficiency and minimize overspray

c. Routine spray booth and filter maintenance, filter selection and installation

d. Compliance with requirements of the NESHAP, Subpart 6H

e. All are required

www.sbeap.org 1-800-578-8898 20. This air regulation requires several records to be kept on file. Which of the following records are not required?

a. Painter training certification

b. Record of gun-cleaning method

c. Documentation of filter efficiency

d. Copies of all notifications and reports required

e. Records of any deviations from requirements in the rule

www.sbeap.org 1-800-578-8898