• Abstract and Figures
• Public Full-text

SECTION 08360 OVERHEAD DOORS

Display hidden notes to specifier. (Don't know how? Click Here)

Copyright 2008 - 2014 ARCAT, Inc. - All rights reserved

PART 1 GENERAL

1.1 SECTION INCLUDES

1.A. Architectural Series: 1.A.1. Full view aluminum doors. (Model 902). 1.A.2. Full view aluminum doors. (Model 903).

1.B. Energy Series with Intellicore: 1.B.1. Steel doors with minor ribs, thermally-broken, polyurethane insulated. (Models 3730, 3720, 3724, 3717, 3715) 1.B.2. Flush steel doors, thermally-broken, polyurethane insulated. (Models 3722,3721, 3722, 3718) 1.B.3. Raised panel steel doors, thermally-broken, polyurethane insulated.(Model 3723)

1.C. Energy Series: 1.C.1. Steel doors with minor ribs, thermally-broken, polystyrene insulated. (Models 3200, 3150) 1.C.2. Flush steel doors, thermally-broken, polystyrene insulated. (Model 3220, 3211, 3155) 1.C.3. Raised panel steel doors, thermally-broken, polystyrene insulated. (Models 3213, 3154)

1.D. Industrial Series: 1.D.1. Deep ribbed steel doors, insulated. (Models 520S, 524S, 524V, 525S, 525V) 1.D.2. Flush steel doors, insulated. (Model 522S) 1.D.3. Raised panel steel doors, insulated. (Model 664V) 1.D.4. Deep ribbed steel doors, non-insulated. (Models 520, 524, 525) 1.D.5. Flush steel doors, non-insulated. (Model 522) 1.D.6.

08360-1 Raised panel steel doors, non-insulated. (Model 664)

1.E. Specialty Aluminum Doors: 1.E.1. Model 811. 1.E.2. Model 812.

1.F. Electric door operators.

1.2 RELATED SECTIONS

2.A. Section 05500 - Metal Fabrications: Steel channel opening frame.

2.B. Section 06100 - Rough Carpentry: Rough wood framing and blocking for door opening.

2.C. Section 08710 - Door Hardware: Lock cylinders.

2.D. Section 11150 - Parking Control Equipment: Remote door control.

2.E. Division 16 Sections: Electrical service and connections for powered operators.

1.3 REFERENCES

3.A. ASTM A 653/A 653M - Specification for Steel Sheet, Zinc-Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvanized) by the Hot-Dip Process.

3.B. ASTM A 924/A 924M - Specification for General Requirements for Steel Sheet, Metallic-Coated by the Hot-Dip Process.

3.C. AAMA 2604 - Voluntary Specification, Performance Requirements and Test Procedures for High Performance Organic Coatings on Aluminum Extrusions and Panels.

1.4 SUBMITTALS

4.A. Submit under provisions of Section 01300.

4.B. Product Data: Manufacturer's data sheets on each product to be used, including: 4.B.1. Preparation instructions and recommendations. 4.B.2. Storage and handling requirements and recommendations. 4.B.3. Installation methods. 4.B.4. Operation and maintenance data. 4.B.5. Nameplate data and ratings for motors.

08360-2 4.C. Shop Drawings: Include opening dimensions and required tolerances, connection details, anchorage spacing, hardware locations, and installation details.

4.D. Selection Samples: For each finish specified, two complete sets of color chips representing manufacturer's full range of available colors and patterns.

4.E. Verification Samples: For each finish specified, two samples, minimum size 6 inches (150 mm) square, representing actual product, color, and patterns.

1.5 WIND PERFORMANCE REQUIREMENTS

5.A. Design doors to withstand positive and negative wind loads as calculated in accordance with applicable building code. 5.A.1. Design Wind Load: ______lb/sf (_____kPa). 5.A.2. Safety Factor: 1.5 times design wind load.

1.6 QUALITY ASSURANCE

6.A. Manufacturer Qualifications: Company specializing in manufacturing the types of doors specified in this section, with not less than ten years of documented experience.

6.B. Installer Qualifications: Company specializing in installing the types of products specified in this section, with minimum of five years of documented experience, and approved by the door manufacturer.

1.7 WARRANTY

7.A. Finish Warranty: Provide manufacturer's standard finish warranty against rusting. 7.A.1. Warranty period: 10 years.

7.B. Delamination Warranty: Provide manufacturer's standard warranty against delamination. 7.B.1. Warranty period: 10 years.

PART 2 PRODUCTS

2.1 MANUFACTURERS

1.A. Acceptable Manufacturer: Clopay Building Products Company, which is located at: 8585 Duke Blvd.; Mason, OH 45040; Toll Free Tel: 800-526-4301; Tel: 513-770-4800; Fax: 888-434-3193; Email: request info ([email protected]); Web: www.clopaydoor.com/commercial/home

1.B. Substitutions: Not permitted.

1.C. Requests for substitutions will be considered in accordance with provisions of Section 01600. 08360-3 2.2 ARCHITECTURAL SERIES

2.A. Full View Heavy Duty 2.125 inches (54 mm) Door - Clopay Model 902.

2.B. Full View Heavy Duty 2.125 inches (54 mm) Door - Clopay Model 903.

2.C. Construction: 2.C.1. Panel Sections: 2-1/8 inches (54 mm) thick extruded 6053-T5 aluminum, with integral reinforcing fin. Enclosed top and bottom rails 3-1/2 inches (89 mm) wide, meeting rails 2- 13/16 inch (71.4 mm) wide, and end stiles 3-1/2 inches (89 mm) wide, with meeting rails meeting to form a tongue-and-groove joint and bottom rail configured to retain U-shaped flexible PVC astragal. Glazing and solid panels installed and sealed with butyl tape and locking retainer. 2.C.2. Maximum Door Size: 20 feet, 2 inches (6.15 m) by 18 feet (5.5 m) high. 2.C.3. Windows: Full-view aluminum sections, pre-painted to match door finish. 2.C.3.a. Glazing: 1/8 inch (3 mm) DSB clear float glass. 2.C.3.b. Glazing: 1/8 inch (3 mm) tempered clear float glass. 2.C.3.c. Glazing: 1/4 inch (6 mm) tempered clear float glass. 2.C.3.d. Glazing: 1/2 inch (13 mm) dual pane tempered insulated glazing. 2.C.3.e. Glazing: 5/8 inch (16mm) triple layer clear polycarbonate glazing. 2.C.3.f. Glazing: 5/8 inch (16mm) triple layer custom color polycarbonate glazing. 2.C.3.g. Glazing: Custom. 2.C.4. Aluminum Finish: Factory pre-painted white. 2.C.5. Aluminum Finish: Factory pre-painted brown. 2.C.6. Aluminum Finish: Factory pre-painted simulated bronze anodized 2.C.7. Aluminum Finish: Clear anodized. 2.C.8. Aluminum Finish: Bronze anodized. 2.C.9. Aluminum Finish: Dark Bronze anodized. 2.C.10. Aluminum Finish: Black anodized. 2.C.11. Aluminum Finish: RAL Powder Coat #______. 2.C.12. Aluminum Finish: Clopay ColorBlast, a two part paint system utilizing Sherwin Williams Solar reflective Polane Paint system, Sherwin Williams color number SW ______. Paint system shall meet or exceed AAMA 2604 standards. 2.C.13. Locking: No Lock. 2.C.14. Locking: Inside spring loaded slide bolt lock on end stile that engages slot in track. 2.C.14.a. Provide one inside slide lock. 08360-4 2.C.14.b. Provide two inside slide locks. 2.C.15. Door Drop Safety Device: Provide brackets designed to stop the fall of the door should lift cables fail. 2.C.16. Weatherstripping: Provide complete perimeter seals. Provide flexible top seal, flexible jamb seal and U shaped bottom seal. 2.C.17. Track: 2.C.17.a. Vertical Track: 2 inches (50 mm) wide, minimum 0.061 inch (1.55mm) galvanized steel tapered and mounted for wedge type closing. 2.C.17.b. Vertical Track: 3 inches (75 mm) wide, minimum 0.099 inch (2.52 mm) galvanized steel tapered and mounted for wedge type closing. 2.C.17.c. Horizontal Track: 2 inches (50 mm) wide, minimum 0.075 inch (1.91 mm) galvanized steel, reinforced with minimum 0.0897 inch (2.28 mm) galvanized steel angles as required. 2.C.17.d. Horizontal Track: 3 inches (50 mm) wide, minimum 0.099 inch (2.52 mm) galvanized steel, reinforced with minimum 0.0897 inch (2.28 mm) galvanized steel angles as required. 2.C.17.e. Provide standard lift tracks with 15 inches (381 mm) radius track as indicated. 2.C.17.f. Provide vertical lift tracks as indicated. 2.C.17.g. Provide high lift tracks as indicated. 2.C.17.h. Provide tracks that follow roof slope tracks as indicated. 2.C.17.i. Provide low headroom tracks as indicated. 2.C.18. Spring Counterbalance: Torsion spring counterbalance mechanism sized to weight of the door, with a helically wound, oil tempered torsion spring mounted on a steel shaft; cable drum of die cast aluminum with high strength galvanized aircraft cable with minimum 7 to 1 safety factor. 2.C.18.a. Standard Cycle Spring: 10,000 cycle. 2.C.18.b. High Cycle Spring: 25,000 cycles. 2.C.18.c. High Cycle Spring: 50,000 cycles. 2.C.18.d. High Cycle Spring: 100,000 cycles.

2.3 STEEL DOORS WITH MINOR RIBS, THERMALLY-BROKEN, POLYURETHANE INSULATED

3.A. Premium 3-inch (75 mm) Door: Clopay Model 3730. 3.A.1. Style: Steel doors with minor ribs, thermally-broken, polyurethane insulated. 3.A.2. Maximum Door Size: 30 feet 2 inches, (9.2 m) wide by 24 ft (7.3 m) high. 3.A.3. Overall Panel Thickness: 3 inches (75 mm). 3.A.4. Steel Skin Thickness: Minimum 27 gauge 0.016 inch (0.40 mm) exterior; minimum 28 gauge 0.015 inch (0.38 mm) interior. 08360-5 3.A.5. Stiles: Steel pre-painted end stiles, minimum 0.061 inch (1.55 mm) thick, engineered for easy hardware attachment through pre-punched holes. 3.A.6. Bottom panel section reinforced with continuous 0.050 inch (1.27 mm) aluminum astragal retainer with U-shaped flexible EPDM astragal. 3.A.7. Thermal Resistance (R-value): 22.2 deg F hr sq ft/Btu (4.40 (K sq m)/W); calculated door section R-value in accordance with DASMA TDS-163. 3.A.8. Windows: None. 3.A.9. Windows: PVC windows measuring 8 inches by 24 inches (200 mm by 600 mm) 3.A.9.a. Glazing: 2 inch nominal (51 mm) insulated triple pane DSB glass. 3.A.10. Windows: PVC windows measuring 12 inches by 24 inches (305 mm by 600 mm) 3.A.10.a. Glazing: 2 inch nominal (51 mm) insulated triple pane DSB glass. 3.A.11. Windows: Black extruded polypropylene windows with rounded corners measuring 13 inches by 26 inches (303 mm by 606 mm). 3.A.11.a. Glazing: 5/8 inch (16 mm) double pane acrylic. 3.A.11.b. Glazing: 5/8 inch (16 mm) double pane lexan. 3.A.12. Finish: Stucco embossed texture with 0.040 inch (100 mm) minor ribs 4 inches or 5 inches (100 or 125 mm) on center, white interior, exterior as follows: 3.A.12.a. White. 3.A.12.b. Brown. 3.A.12.c. Clopay ColorBlast, a two part paint system utilizing Sherwin Williams Solar reflective Polane Paint system. Sherwin Williams color number SW ______. Paint system shall meet or exceed AAMA 2604 standards. 3.A.13. Locking: No Lock. 3.A.14. Locking: Inside spring loaded slide bolt lock on end stile that engages slot in track. 3.A.14.a. Provide one inside slide lock. 3.A.14.b. Provide two inside slide locks. 3.A.14.c. Provide five pin cylinder lock with outside key. 3.A.15. Door Drop Safety Device: Provide brackets designed to stop the fall of the door should lift cables fail. 3.A.16. Weatherstripping: Provide complete perimeter seals selected from manufacturer's standard options. Provide flexible top seal, flexible jamb seal and U shaped bottom seal. 3.A.17. Tracks: Vertical tracks minimum 0.061 inch (1.55mm) for 2" track or .099 inch (2.52mm) for 3 " track galvanized steel tapered and mounted for wedge type closing. Horizontal tracks minimum 0.075 inch (1.91 mm) for 2" track or .099 inch (2.52mm) for 3 " track galvanized steel, reinforced with minimum 0.0897 inch (2.28 mm) galvanized steel angles as required: 3.A.17.a. Track Width: 2 inches (50 mm). 3.A.17.b. 08360-6 Track Width: 3 inches (75 mm). 3.A.17.c. Provide standard lift tracks with 15 inches (381 mm) radius track as indicated. 3.A.17.d. Provide vertical lift tracks as indicated. 3.A.17.e. Provide high lift tracks as indicated. 3.A.17.f. Provide tracks that follow roof slope tracks as indicated. 3.A.17.g. Provide low headroom tracks as indicated. 3.A.18. Spring Counterbalance: Torsion spring counterbalance mechanism sized to weight of the door, with a helically wound, oil tempered torsion spring mounted on a steel shaft; cable drum of die cast aluminum with high strength galvanized aircraft cable with minimum 7 to 1 safety factor. 3.A.18.a. Standard Cycle Spring: 10,000 cycle. 3.A.18.b. High Cycle Spring: 25,000 cycles. 3.A.18.c. High Cycle Spring: 50,000 cycles. 3.A.18.d. High Cycle Spring: 100,000 cycles.

3.B. Premium Duty 2-inches (51 mm) Door: Clopay Model 3720. 3.B.1. Style: Steel doors with minor ribs, thermally-broken, polyurethane insulated. 3.B.2. Maximum Door Size: 36 feet, 2 inches (11.0 m) wide by 26 feet (7.9 m) high. 3.B.3. Overall Panel Thickness: 2-inches (51 mm). 3.B.4. Steel Skin Thickness: Minimum 27 gauge 0.016 inch (0.40 mm) exterior; minimum 28 gauge 0.015 inch (0.38 mm) interior. 3.B.5. End Stiles: Galvanized steel end stiles, engineered for easy hardware attachment through pre-punched holes. Minimum 18 gauge, 0.045 inch (1.14 mm) thick for single end hinge style and 16 gauge .056 inch (1.42 mm) minimum for double end hinge style. 3.B.6. Astragal: U-shaped flexible PVC in retainer of full-length 0.055 inch (1.4 mm) rigid PVC. 3.B.7. Thermal Resistance (R-value): 18.4 deg F hr sq ft/Btu (3.0 (K sq m)/W); calculated door section R-value in accordance with DASMA TDS-163. 3.B.8. Windows: None. 3.B.9. Windows: Extruded polypropylene windows measuring 8 inches by 24 inches (200 mm by 600 mm). 3.B.9.a. Glazing: 1 inch nominal (25 mm) insulated glass. 3.B.9.b. Glazing: 1 inch nominal (25 mm) insulated tempered glass. 3.B.9.c. Glazing: 1/4 inch (6 mm) tempered glass. 3.B.10. Windows: Extruded polypropylene windows measuring 12 inches by 24 inches (305 mm by 600 mm). 3.B.10.a. Glazing: 1 inch nominal (25 mm) insulated glass. 3.B.10.b. 08360-7 Glazing: 1 inch nominal (25 mm) insulated tempered glass. 3.B.10.c. Glazing: 1/4 inch (6 mm) tempered glass.. 3.B.11. Windows: Full vision aluminum section, pre-painted to match door finish. 3.B.11.a. Glazing: 1/8 inch (3 mm) DSB clear float glass. 3.B.11.b. Glazing: 1/4 inch (6 mm) tempered clear float glass. 3.B.11.c. Glazing: 1/2 inch (13 mm) dual pane insulated glazing. 3.B.11.d. Glazing: 5/8 inch (16mm) triple layer clear polycarbonate glazing. 3.B.11.e. Glazing: 5/8 inch (16mm) triple layer custom color polycarbonate glazing. 3.B.12. Windows: Black extruded polypropylene windows with rounded corners measuring 13 inches by 26 inches (303 mm by 606 mm). 3.B.12.a. Glazing: 5/8 inch (16 mm) double pane acrylic. 3.B.12.b. Glazing: 5/8 inch (16 mm) double pane lexan. 3.B.13. Finish: Interior stucco embossed texture with shallow U ribbed pattern, white interior color. Exterior stucco embossed with ribbed pattern, exterior as follows: 3.B.13.a. White. 3.B.13.b. Glacier White 3.B.13.c. Brown. 3.B.13.d. Commercial Tan 3.B.13.e. Commercial Gray 3.B.13.f. Trinar White 3.B.13.g. Trinar Beige 3.B.13.h. Clopay ColorBlast, a two part paint system utilizing Sherwin Williams Solar reflective Polane Paint system. Sherwin Williams color number SW ______. Paint system shall meet or exceed AAMA 2604 standards. 3.B.14. Locking: No Lock. 3.B.15. Locking: Inside spring loaded slide bolt lock on end stile that engages slot in track. 3.B.15.a. Provide one inside slide lock. 3.B.15.b. Provide two inside slide locks. 3.B.16. Provide five pin cylinder lock with outside key. 3.B.17. Door Drop Safety Device: Provide brackets designed to stop the fall of the door should lift cables fail. 3.B.18. Weatherstripping: Provide complete perimeter seals. Provide flexible top seal, flexible jamb seal and U shaped bottom seal. 3.B.19. Track: 3.B.19.a. 08360-8 Vertical Track: 2 inches (50 mm) wide, minimum 0.061 inch (1.55mm) galvanized steel tapered and mounted for wedge type closing. 3.B.19.b. Vertical Track: 3 inches (75 mm) wide, minimum 0.099 inch (2.52 mm) galvanized steel tapered and mounted for wedge type closing. 3.B.19.c. Horizontal Track: 2 inches (50 mm) wide, minimum 0.075 inch (1.91 mm) galvanized steel, reinforced with minimum 0.0897 inch (2.28 mm) galvanized steel angles as required. 3.B.19.d. Horizontal Track: 3 inches (50 mm) wide, minimum 0.099 inch (2.52 mm) galvanized steel, reinforced with minimum 0.0897 inch (2.28 mm) galvanized steel angles as required. 3.B.19.e. Provide standard lift tracks with 15 inches (381 mm) radius track as indicated. 3.B.19.f. Provide vertical lift tracks as indicated. 3.B.19.g. Provide high lift tracks as indicated. 3.B.19.h. Provide tracks that follow roof slope tracks as indicated. 3.B.19.i. Provide low headroom tracks as indicated. 3.B.20. Spring Counterbalance: Torsion spring counterbalance mechanism sized to weight of the door, with a helically wound, oil tempered torsion spring mounted on a steel shaft; cable drum of die cast aluminum with high strength galvanized aircraft cable with minimum 7 to 1 safety factor. 3.B.20.a. Standard Cycle Spring: 10,000 cycle. 3.B.20.b. High Cycle Spring: 25,000 cycles. 3.B.20.c. High Cycle Spring: 50,000 cycles. 3.B.20.d. High Cycle Spring: 100,000 cycles. 3.B.21. Break-Away Bottom Section: Integral part of door; with fiberglass or 1/8 inch (3 mm) polycarbonate lined bottom section with flexible neoprene rubber side edges; exterior to match door face. 3.B.21.a. Single breakaway bottom section for doors up to 20 feet (6 m) wide. 3.B.21.b. Double breakaway bottom section for doors up to 14 feet (4.3 m) wide. 3.B.22. Pass Door (Walk-Through Service Door): Integral part of door; 32 inches (813 mm) by 80 inches (2032 mm) with aluminum frame, welded corners, geared hinge, and pneumatic door closer; exterior matching door face; integral shiplap weather seal; keyed dead latch security lock.

3.C. Premium Duty 2-inches (51 mm) Door: Clopay Model 3724. 3.C.1. Style: Steel doors with minor ribs, thermally-broken, polyurethane insulated. 3.C.2. Maximum Door Size: 36 feet, 2 inches (11.0 m) wide by 24 feet (7.3 m) high. 3.C.3. Overall Panel Thickness: 2-inches (51 mm). 3.C.4. Steel Skin Thickness: Minimum 24 gauge 0.022 inch (0.56 mm) exterior; minimum 28 gauge 0.015 inch (0.38 mm) interior. 3.C.5. 08360-9 End Stiles: Galvanized steel end stiles, engineered for easy hardware attachment through pre-punched holes. Minimum 18 gauge, 0.045 inch (1.14 mm) thick for single end hinge style and 16 gauge .056 inch (1.42 mm) minimum for double end hinge style. 3.C.6. Astragal: U-shaped flexible PVC in retainer of full-length 0.055 inch (1.4 mm) rigid PVC. 3.C.7. Thermal Resistance (R-value): 18.4 deg F hr sq ft/Btu (3.0 (K sq m)/W); calculated door section R-value in accordance with DASMA TDS-163. 3.C.8. Windows: None. 3.C.9. Windows: Extruded polypropylene windows measuring 8 inches by 24 inches (200 mm by 600 mm). 3.C.9.a. Glazing: 1 inch nominal (25 mm) insulated glass. 3.C.9.b. Glazing: 1 inch nominal (25 mm) insulated tempered glass. 3.C.9.c. Glazing: 1/4 inch (6 mm) tempered glass. 3.C.10. Windows: Extruded polypropylene windows measuring 12 inches by 24 inches (305 mm by 600 mm). 3.C.10.a. Glazing: 1 inch nominal (25 mm) insulated glass. 3.C.10.b. Glazing: 1 inch nominal (25 mm) insulated tempered glass. 3.C.10.c. Glazing: 1/4 inch (6 mm) tempered glass.. 3.C.11. Windows: Full vision aluminum section, pre-painted to match door finish. 3.C.11.a. Glazing: 1/8 inch (3 mm) DSB clear float glass. 3.C.11.b. Glazing: 1/4 inch (6 mm) tempered clear float glass. 3.C.11.c. Glazing: 1/2 inch (13 mm) dual pane insulated glazing. 3.C.11.d. Glazing: 5/8 inch (16mm) triple layer clear polycarbonate glazing. 3.C.11.e. Glazing: 5/8 inch (16mm) triple layer custom color polycarbonate glazing. 3.C.12. Windows: Black extruded polypropylene windows with rounded corners measuring 13 inches by 26 inches (303 mm by 606 mm). 3.C.12.a. Glazing: 5/8 inch (16 mm) double pane acrylic. 3.C.12.b. Glazing: 5/8 inch (16 mm) double pane lexan. 3.C.13. Finish: Interior stucco embossed texture with shallow U ribbed pattern, white interior color. Exterior stucco embossed with ribbed pattern, exterior as follows: 3.C.13.a. White. 3.C.13.b. Brown. 3.C.13.c. Commercial Tan. 3.C.13.d. Gray. 3.C.13.e. Black. 3.C.13.f. Trinar White. 08360-10 3.C.13.g. Clopay ColorBlast, a two part paint system utilizing Sherwin Williams Solar reflective Polane Paint system. Sherwin Williams color number SW ______. Paint system shall meet or exceed AAMA 2604 standards. 3.C.14. Locking: No Lock. 3.C.15. Locking: Inside spring loaded slide bolt lock on end stile that engages slot in track. 3.C.15.a. Provide one inside slide lock. 3.C.15.b. Provide two inside slide locks. 3.C.15.c. Provide five pin cylinder lock with outside key. 3.C.16. Door Drop Safety Device: Provide brackets designed to stop the fall of the door should lift cables fail. 3.C.17. Weatherstripping: Provide complete perimeter seals. Provide flexible top seal, flexible jamb seal and U shaped bottom seal. 3.C.18. Track: 3.C.18.a. Vertical Track: 2 inches (50 mm) wide, minimum 0.061 inch (1.55mm) galvanized steel tapered and mounted for wedge type closing. 3.C.18.b. Vertical Track: 3 inches (75 mm) wide, minimum 0.099 inch (2.52 mm) galvanized steel tapered and mounted for wedge type closing. 3.C.18.c. Horizontal Track: 2 inches (50 mm) wide, minimum 0.075 inch (1.91 mm) galvanized steel, reinforced with minimum 0.0897 inch (2.28 mm) galvanized steel angles as required. 3.C.18.d. Horizontal Track: 3 inches (50 mm) wide, minimum 0.099 inch (2.52 mm) galvanized steel, reinforced with minimum 0.0897 inch (2.28 mm) galvanized steel angles as required. 3.C.18.e. Provide standard lift tracks with 15 inches (381 mm) radius track as indicated. 3.C.18.f. Provide vertical lift tracks as indicated. 3.C.18.g. Provide high lift tracks as indicated. 3.C.18.h. Provide tracks that follow roof slope tracks as indicated. 3.C.18.i. Provide low headroom tracks as indicated. 3.C.19. Spring Counterbalance: Torsion spring counterbalance mechanism sized to weight of the door, with a helically wound, oil tempered torsion spring mounted on a steel shaft; cable drum of die cast aluminum with high strength galvanized aircraft cable with minimum 7 to 1 safety factor. 3.C.19.a. Standard Cycle Spring: 10,000 cycle. 3.C.19.b. High Cycle Spring: 25,000 cycles. 3.C.19.c. High Cycle Spring: 50,000 cycles. 3.C.19.d. High Cycle Spring: 100,000 cycles. 3.C.20. Break-Away Bottom Section: Integral part of door; with fiberglass or 1/8 inch (3 mm) polycarbonate lined bottom section with flexible neoprene rubber side edges; exterior to 08360-11 match door face. 3.C.20.a. Single breakaway bottom section for doors up to 20 feet (6 m) wide. 3.C.20.b. Double breakaway bottom section for doors up to 14 feet (4.3 m) wide. 3.C.21. Pass Door (Walk-Through Service Door): Integral part of door; 32 inches (813 mm) by 80 inches (2032 mm) with aluminum frame, welded corners, geared hinge, and pneumatic door closer; exterior matching door face; integral shiplap weather seal; keyed dead latch security lock.

3.D. Heavy Duty 1-3/4-inches (45 mm) Door: Clopay Model 3717. 3.D.1. Style: Steel doors with minor ribs, thermally-broken, polyurethane insulated. 3.D.2. Maximum Door Size: 32 feet, 2 inches (9.8 m) wide by 26 feet (7.9 m) high. 3.D.3. Overall Panel Thickness: 1-3/4-inches (45 mm). 3.D.4. Steel Skin Thickness: Minimum 27 gauge 0.016 inch (0.40 mm) exterior; minimum 28 gauge 0.015 inch (0.38 mm) interior. 3.D.5. End Stiles: Galvanized steel end stiles, engineered for easy hardware attachment through pre-punched holes. Minimum 18 gauge, 0.045 inch (1.14 mm) thick for single end hinge style and 16 gauge .056 inch (1.42 mm) minimum for double end hinge style. 3.D.6. Astragal: U-shaped flexible PVC in retainer of full-length 0.055 inch (1.4 mm) rigid PVC. 3.D.7. Thermal Resistance (R-value): 16.2 deg F hr sq ft/Btu (2.7 (K sq m)/W); calculated door section R-value in accordance with DASMA TDS-163. 3.D.8. Windows: None. 3.D.9. Windows: Extruded polypropylene windows measuring 8 inches by 24 inches (200 mm by 600 mm). 3.D.9.a. Glazing: 7/8 inch (22 mm) insulated glass. 3.D.9.b. Glazing: 7/8 inch (22 mm) insulated tempered glass. 3.D.9.c. Glazing: 1/4 inch (6 mm) tempered glass. 3.D.10. Windows: Extruded polypropylene windows measuring 12 inches by 24 inches (305 mm by 600 mm). 3.D.10.a. Glazing: 7/8 inch (22 mm) insulated glass. 3.D.10.b. Glazing: 7/8 inch (22 mm) insulated tempered glass. 3.D.10.c. Glazing: 1/4 inch (6 mm) tempered glass. 3.D.11. Windows: Full vision aluminum section, pre-painted to match door finish. 3.D.11.a. Glazing: 1/8 inch (3 mm) DSB clear float glass. 3.D.11.b. Glazing: 1/4 inch (6 mm) tempered clear float glass. 3.D.11.c. Glazing: 1/2 inch (13 mm) dual pane insulated glazing. 3.D.12. Windows: Black extruded polypropylene windows with rounded corners measuring 13 inches by 26 inches (303 mm by 606 mm). 08360-12 3.D.12.a. Glazing: 5/8 inch (16 mm) double pane acrylic. 3.D.12.b. Glazing: 5/8 inch (16 mm) double pane lexan. 3.D.13. Finish: Interior stucco embossed texture with shallow U ribbed pattern, white color. Exterior stucco embossed with ribbed pattern, exterior color as follows: 3.D.13.a. White. 3.D.13.b. Brown. 3.D.13.c. Commercial Tan. 3.D.13.d. Gray. 3.D.13.e. Trinar White. 3.D.13.f. Trinar Beige. 3.D.13.g. Clopay ColorBlast, a two part paint system utilizing Sherwin Williams Solar reflective Polane Paint system. Sherwin Williams color number SW ______. Paint system shall meet or exceed AAMA 2604 standards. 3.D.14. Locking: No Lock. 3.D.15. Locking: Inside spring loaded slide bolt lock on end stile that engages slot in track. 3.D.15.a. Provide one inside slide lock. 3.D.15.b. Provide two inside slide lock. 3.D.15.c. Provide five pin cylinder lock with outside key. 3.D.16. Door Drop Safety Device: Provide brackets designed to stop the fall of the door should lift cables fail. 3.D.17. Weatherstripping: Provide complete perimeter seals. Provide flexible top seal, flexible jamb seal and U shaped bottom seal. 3.D.18. Track: 3.D.18.a. Vertical Track: 2 inches (50 mm) wide, minimum 0.061 inch (1.55mm) galvanized steel tapered and mounted for wedge type closing. 3.D.18.b. Vertical Track: 3 inches (75 mm) wide, minimum 0.099 inch (2.52 mm) galvanized steel tapered and mounted for wedge type closing. 3.D.18.c. Horizontal Track: 2 inches (50 mm) wide, minimum 0.075 inch (1.91 mm) galvanized steel, reinforced with minimum 0.0897 inch (2.28 mm) galvanized steel angles as required. 3.D.18.d. Horizontal Track: 3 inches (50 mm) wide, minimum 0.099 inch (2.52 mm) galvanized steel, reinforced with minimum 0.0897 inch (2.28 mm) galvanized steel angles as required. 3.D.18.e. Provide standard lift tracks with 15 inches (381 mm) radius track as indicated. 3.D.18.f. Provide vertical lift tracks as indicated. 3.D.18.g. Provide high lift tracks as indicated. 3.D.18.h. 08360-13 Provide tracks that follow roof slope tracks as indicated. 3.D.18.i. Provide low headroom tracks as indicated. 3.D.19. Spring Counterbalance: Torsion spring counterbalance mechanism sized to weight of the door, with a helically wound, oil tempered torsion spring mounted on a steel shaft; cable drum of die cast aluminum with high strength galvanized aircraft cable with minimum 7 to 1 safety factor. 3.D.19.a. Standard Cycle Spring: 10,000 cycle. 3.D.19.b. High Cycle Spring: 25,000 cycles. 3.D.19.c. High Cycle Spring: 50,000 cycles. 3.D.19.d. High Cycle Spring: 100,000 cycles. 3.D.20. Break-Away Bottom Section: Integral part of door; with fiberglass or 1/8 inch (3 mm) polycarbonate lined bottom section with flexible neoprene rubber side edges; exterior to match door face. 3.D.20.a. Single breakaway bottom section for doors up to 20 feet (6 m) wide. 3.D.20.b. Double breakaway bottom section for doors up to 14 feet (4.3 m) wide.

3.E. Standard Duty 1-3/8-inches (35 mm) Door: Clopay Model 3715. 3.E.1. Style: Steel doors with minor ribs, thermally-broken, polyurethane insulated. 3.E.2. Maximum Door Size: 18 feet, 2 inches (5.5 m) wide by 16 feet (4.9 m) high. 3.E.3. Overall Panel Thickness: 1-3/8-inches (35 mm). 3.E.4. Steel Skin Thickness: Minimum 27 gauge 0.016 inch (0.40 mm) exterior; minimum 28 gauge 0.015 inch (0.38 mm) interior. 3.E.5. End Stiles: Galvanized steel end stiles, minimum 20 gauge, 0.034 inch (.86 mm) thick, engineered for easy hardware attachment through pre-punched holes. 3.E.6. Astragal: U-shaped flexible PVC in retainer of full-length 0.055 inch (1.4 mm) rigid PVC. 3.E.7. Thermal Resistance (R-value): 12.9 deg F hr sq ft/Btu (2.3 (K sq m)/W); calculated door section R-value in accordance with DASMA TDS-163. 3.E.8. Windows: None. 3.E.9. Windows: Extruded polypropylene windows measuring 8 inches by 24 inches (200 mm by 600 mm). 3.E.9.a. Glazing: 1/2 inch (12 mm) insulated glass. 3.E.9.b. Glazing: 1/2 inch (12 mm) insulated tempered glass. 3.E.9.c. Glazing: 1/4 inch (6 mm) tempered glass. 3.E.10. Windows: Extruded polypropylene windows measuring 12 inches by 24 inches (305 mm by 600 mm). 3.E.10.a. Glazing: 1/2 inch (12 mm) insulated glass. 3.E.10.b. Glazing: 1/2 inch (12 mm) insulated tempered glass. 08360-14 3.E.10.c. Glazing: 1/4 inch (6 mm) tempered glass. 3.E.11. Windows: Full vision section, pre-painted to match door finish. 3.E.11.a. Glazing: 1/8 inch (3 mm) DSB clear float glass. 3.E.11.b. Glazing: 1/2 inch (13 mm) dual pane insulated glazing. 3.E.12. Finish: Interior stucco embossed texture with ribbed pattern, white. Exterior stucco embossed with ribbed pattern, exterior color as follows: 3.E.12.a. White. 3.E.12.b. Glacier White 3.E.12.c. Brown. 3.E.12.d. Commercial Tan. 3.E.12.e. Gray. 3.E.12.f. Clopay ColorBlast, a two part paint system utilizing Sherwin Williams Solar reflective Polane Paint system. Sherwin Williams color number SW ______. Paint system shall meet or exceed AAMA 2604 standards. 3.E.13. Locking: No Lock. 3.E.14. Locking: Inside spring loaded slide bolt lock on end stile that engages slot in track. 3.E.14.a. Provide one inside slide lock. 3.E.14.b. Provide two inside slide lock. 3.E.14.c. Provide five pin cylinder lock with outside key. 3.E.15. Door Drop Safety Device: Provide brackets designed to stop the fall of the door should lift cables fail. 3.E.16. Weatherstripping: Provide complete perimeter seals. Provide flexible top seal, flexible jamb seal and U shaped bottom seal. 3.E.17. Track: 3.E.17.a. Vertical Track: 2 inches (50 mm) wide, minimum 0.061 inch (1.55mm) galvanized steel tapered and mounted for wedge type closing. 3.E.17.b. Vertical Track: 3 inches (75 mm) wide, minimum 0.099 inch (2.52 mm) galvanized steel tapered and mounted for wedge type closing. 3.E.17.c. Horizontal Track: 2 inches (50 mm) wide, minimum 0.075 inch (1.91 mm) galvanized steel, reinforced with minimum 0.0897 inch (2.28 mm) galvanized steel angles as required. 3.E.17.d. Horizontal Track: 3 inches (50 mm) wide, minimum 0.099 inch (2.52 mm) galvanized steel, reinforced with minimum 0.0897 inch (2.28 mm) galvanized steel angles as required. 3.E.17.e. Provide standard lift tracks with 15 inches (381 mm) radius track as indicated. 3.E.17.f. Provide vertical lift tracks as indicated. 3.E.17.g. 08360-15 Provide high lift tracks as indicated. 3.E.17.h. Provide tracks that follow roof slope tracks as indicated. 3.E.17.i. Provide low headroom tracks as indicated. 3.E.18. Spring Counterbalance: Torsion spring counterbalance mechanism sized to weight of the door, with a helically wound, oil tempered torsion spring mounted on a steel shaft; cable drum of die cast aluminum with high strength galvanized aircraft cable with minimum 7 to 1 safety factor. 3.E.18.a. Standard Cycle Spring: 10,000 cycle. 3.E.18.b. High Cycle Spring: 25,000 cycles. 3.E.18.c. High Cycle Spring: 50,000 cycles. 3.E.18.d. High Cycle Spring: 100,000 cycles.

3.F. Door Construction: 3.F.1. Style: Steel doors with minor ribs, thermally-broken, polyurethane insulated. 3.F.2. Panels: Foamed in place Polyurethane core construction between exterior and interior steel skins. 3.F.3. Steel Skins: Formed from roll formed commercial or drawing quality steel sheet, hot-dip galvanized per ASTM A 924/A 924M and ASTM A 653/A 653M, pre-painted with primer and baked-on polyester topcoat; sections formed to create weather tight tongue-in- groove meeting joint. 3.F.4. Reinforcing: Galvanized and primed steel reinforcement located under each hinge location, pre-punched for hinge attachment. 3.F.5. Handle: Step plate/lift handle on bottom panel section.

2.4 FLUSH STEEL DOORS, THERMALLY-BROKEN, POLYURETHANE INSULATED

4.A. Premium Duty Insulated 2-inches (51 mm) Door: Clopay Model 3721. 4.A.1. Style: Flush steel doors, thermally-broken, polyurethane insulated. 4.A.2. Maximum Door Size: 24 feet, 2 inches (7.4 m) wide by 18 feet (5.5 m) high. 4.A.3. Overall Panel Thickness: 1-3/4-inches (45 mm). 4.A.4. Steel Skin Thickness: Minimum 27 gauge 0.016 inch (0.40 mm) exterior; minimum 28 gauge 0.015 inch (0.38 mm) interior. 4.A.5. End Stiles: Galvanized steel end stiles, engineered for easy hardware attachment through pre-punched holes. Minimum 18 gauge, 0.045 inch (1.14 mm) thick for single end hinge style and 16 gauge .056 inch (1.42 mm) minimum for double end hinge style. 4.A.6. Astragal: U-shaped flexible PVC in retainer of full-length 0.055 inch (1.4 mm) rigid PVC. 4.A.7. Thermal Resistance (R-value): 18.4 deg F hr sq ft/Btu (2.7 (K sq m)/W); calculated door section R-value in accordance with DASMA TDS-163. 4.A.8. Finish: Interior stucco embossed texture with shallow U ribbed pattern, white interior 08360-16 color. 4.A.9. Exterior: Woodgrain embossed texture with flush exterior panel color as follows: 4.A.9.a. White. 4.A.9.b. Brown. 4.A.9.c. Almond. 4.A.9.d. Desert Tan. 4.A.9.e. Sandtone. 4.A.9.f. Commercial Tan. 4.A.9.g. Clopay ColorBlast, a two part paint system utilizing Sherwin Williams Solar reflective Polane Paint system. Sherwin Williams color number SW ______. Paint system shall meet or exceed AAMA 2604 standards. 4.A.10. Windows: None. 4.A.11. Windows: Extruded polypropylene windows measuring 8 inches by 24 inches (200 mm by 600 mm). 4.A.11.a. Glazing: 7/8 inch (22 mm) insulated glass. 4.A.11.b. Glazing: 7/8 inch (22 mm) insulated tempered glass. 4.A.11.c. Glazing: 1/4 inch (6 mm) tempered glass. 4.A.12. Windows: Extruded polypropylene windows measuring 12 inches by 24 inches (305 mm by 600 mm). 4.A.12.a. Glazing: 7/8 inch (22 mm) insulated glass. 4.A.12.b. Glazing: 7/8 inch (22 mm) insulated tempered glass. 4.A.12.c. Glazing: 1/4 inch (6 mm) tempered glass. 4.A.13. Windows: Full vision aluminum section, pre-painted to match door finish. 4.A.13.a. Glazing: 1/8 inch (3 mm) DSB clear float glass. 4.A.13.b. Glazing: 1/4 inch (6 mm) tempered clear float glass. 4.A.13.c. Glazing: 1/2 inch (13 mm) dual pane insulated glazing. 4.A.13.d. Glazing: 5/8 inch (16mm) triple layer custom color polycarbonate glazing. 4.A.14. Windows: Black extruded polypropylene windows with rounded corners measuring 13 inches by 26 inches (303 mm by 606 mm). 4.A.14.a. Glazing: 5/8 inch (16 mm) double pane acrylic. 4.A.14.b. Glazing: 5/8 inch (16 mm) double pane lexan. 4.A.15. Window: Extruded polypropylene windows measuring 12 inches by 19.5 inches (305 mm by 495 mm). 4.A.15.a. Glazing: 1/8 inch (3 mm) DSB sheet glass. 4.A.15.b. 08360-17 Glazing: 1/8 inch (3 mm) acrylic sheet. 4.A.15.c. Glazing: 1/2 inch (12 mm) insulated glass glazing 4.A.16. Locking: No Lock. 4.A.17. Locking: Inside spring loaded slide bolt lock on end stile that engages slot in track. 4.A.17.a. Provide one inside slide lock. 4.A.17.b. Provide two inside slide lock. 4.A.17.c. Provide five pin cylinder lock with outside key. 4.A.18. Door Drop Safety Device: Provide brackets designed to stop the fall of the door should lift cables fail. 4.A.19. Weatherstripping: Provide complete perimeter seals. Provide flexible top seal, flexible jamb seal and U shaped bottom seal.

4.B. Premium Duty Insulated 2-inches (51 mm) Door: Clopay Model 3722. 4.B.1. Style: Flush steel doors, thermally-broken, polyurethane insulated. 4.B.2. Maximum Door Size: 36 feet, 2 inches (11.0 m) wide by 24 feet (7.3 m) high. 4.B.3. Overall Panel Thickness: 1-3/4-inches (45 mm). 4.B.4. Steel Skin Thickness: Minimum 20 ga .034 inch (0.86 mm) exterior; minimum 28 gauge 0.015 inch (0.38 mm) interior. 4.B.5. End Stiles: Galvanized steel end stiles, engineered for easy hardware attachment through pre-punched holes. Minimum 18 gauge, 0.045 inch (1.14 mm) thick for single end hinge style and 16 gauge .056 inch (1.42 mm) minimum for double end hinge style. 4.B.6. Astragal: U-shaped flexible PVC in retainer of full-length 0.055 inch (1.4 mm) rigid PVC. 4.B.7. Thermal Resistance (R-value): 18.4 deg F hr sq ft/Btu (2.7 (K sq m)/W); calculated door section R-value in accordance with DASMA TDS-163. 4.B.8. Finish: Interior stucco embossed texture with shallow U ribbed pattern, white interior color. 4.B.9. Exterior: Stucco embossed texture with flush exterior panel and color as follows: 4.B.9.a. White. 4.B.9.b. Brown. 4.B.9.c. Clopay ColorBlast, a two part paint system utilizing Sherwin Williams Solar reflective Polane Paint system. Sherwin Williams color number SW ______. Paint system shall meet or exceed AAMA 2604 standards. 4.B.10. Windows: None. 4.B.11. Windows: Extruded polypropylene windows measuring 8 inches by 24 inches (200 mm by 600 mm). 4.B.11.a. Glazing: 7/8 inch (22 mm) insulated glass. 4.B.11.b. Glazing: 7/8 inch (22 mm) insulated tempered glass. 08360-18 4.B.11.c. Glazing: 1/4 inch (6 mm) tempered glass. 4.B.12. Windows: Extruded polypropylene windows measuring 12 inches by 24 inches (305 mm by 600 mm). 4.B.12.a. Glazing: 7/8 inch (22 mm) insulated glass. 4.B.12.b. Glazing: 7/8 inch (22 mm) insulated tempered glass. 4.B.12.c. Glazing: 1/4 inch (6 mm) tempered glass. 4.B.13. Windows: Full vision aluminum section, pre-painted to match door finish. 4.B.13.a. Glazing: 1/8 inch (3 mm) DSB clear float glass. 4.B.13.b. Glazing: 1/4 inch (6 mm) tempered clear float glass. 4.B.13.c. Glazing: 1/2 inch (13 mm) dual pane insulated glazing. 4.B.13.d. Glazing: 5/8 inch (16mm) triple layer clear polycarbonate glazing. 4.B.13.e. Glazing: 5/8 inch (16mm) triple layer custom color polycarbonate glazing. 4.B.14. Windows: Black extruded polypropylene windows with rounded corners measuring 13 inches by 26 inches (303 mm by 606 mm). 4.B.14.a. Glazing: 5/8 inch (16 mm) double pane acrylic. 4.B.14.b. Glazing: 5/8 inch (16 mm) double pane lexan. 4.B.15. Locking: No Lock. 4.B.16. Locking: Inside spring loaded slide bolt lock on end stile that engages slot in track. 4.B.16.a. Provide one inside slide lock. 4.B.16.b. Provide two inside slide lock. 4.B.16.c. Provide five pin cylinder lock with outside key. 4.B.17. Door Drop Safety Device: Provide brackets designed to stop the fall of the door should lift cables fail. 4.B.18. Weatherstripping: Provide complete perimeter seals. Provide flexible top seal, flexible jamb seal and U shaped bottom seal.

4.C. Heavy Duty 1-3/4-inches (45 mm) Door: Clopay Model 3718. 4.C.1. Style: Flush steel doors, thermally-broken, polyurethane insulated. 4.C.2. Maximum Door Size: 32 feet, 2 inches (9.8 m) wide by 24 feet (7.3 m) high. 4.C.3. Overall Panel Thickness: 1-3/4-inches (45 mm). 4.C.4. Steel Skin Thickness: Minimum 27 gauge 0.016 inch (0.40 mm) exterior; minimum 28 gauge 0.015 inch (0.38 mm) interior. 4.C.5. End Stiles: Galvanized steel end stiles, engineered for easy hardware attachment through pre-punched holes. Minimum 18 gauge, 0.045 inch (1.14 mm) thick for single end hinge style and 16 gauge .056 inch (1.42 mm) minimum for double end hinge style. 08360-19 4.C.6. Astragal: U-shaped flexible PVC in retainer of full-length 0.055 inch (1.4 mm) rigid PVC. 4.C.7. Thermal Resistance (R-value): 16.2 deg F hr sq ft/Btu (2.7 (K sq m)/W); calculated door section R-value in accordance with DASMA TDS-163. 4.C.8. Finish: Interior stucco embossed texture with shallow U ribbed pattern, white color. Exterior stucco embossed texture with flush panel, exterior color as follows: 4.C.8.a. White. 4.C.8.b. Glacier White 4.C.8.c. Brown. 4.C.8.d. Commercial Tan. 4.C.8.e. Gray. 4.C.8.f. Trinar White. 4.C.8.g. Trinar Beige. 4.C.8.h. Clopay ColorBlast, a two part paint system utilizing Sherwin Williams Solar reflective Polane Paint system. Sherwin Williams color number SW ______. Paint system shall meet or exceed AAMA 2604 standards. 4.C.9. Windows: None. 4.C.10. Windows: Extruded polypropylene windows measuring 8 inches by 24 inches (200 mm by 600 mm). 4.C.10.a. Glazing: 7/8 inch (22 mm) insulated glass. 4.C.10.b. Glazing: 7/8 inch (22 mm) insulated tempered glass. 4.C.10.c. Glazing: 1/4 inch (6 mm) tempered glass. 4.C.11. Windows: Extruded polypropylene windows measuring 12 inches by 24 inches (305 mm by 600 mm). 4.C.11.a. Glazing: 7/8 inch (22 mm) insulated glass. 4.C.11.b. Glazing: 7/8 inch (22 mm) insulated tempered glass. 4.C.11.c. Glazing: 1/4 inch (6 mm) tempered glass. 4.C.12. Windows: Full vision aluminum section, pre-painted to match door finish. 4.C.12.a. Glazing: 1/8 inch (3 mm) DSB clear float glass. 4.C.12.b. Glazing: 1/4 inch (6 mm) tempered clear float glass. 4.C.12.c. Glazing: 1/2 inch (13 mm) dual pane insulated glazing. 4.C.12.d. Glazing: 5/8 inch (16mm) triple layer custom color polycarbonate glazing. 4.C.13. Windows: Black extruded polypropylene windows with rounded corners measuring 13 inches by 26 inches (303 mm by 606 mm). 4.C.13.a. Glazing: 5/8 inch (16 mm) double pane acrylic. 4.C.13.b. 08360-20 Glazing: 5/8 inch (16 mm) double pane lexan. 4.C.14. Locking: No Lock. 4.C.15. Locking: Inside spring loaded slide bolt lock on end stile that engages slot in track. 4.C.15.a. Provide one inside slide lock. 4.C.15.b. Provide two inside slide lock. 4.C.15.c. Provide five pin cylinder lock with outside key. 4.C.16. Door Drop Safety Device: Provide brackets designed to stop the fall of the door should lift cables fail. 4.C.17. Weatherstripping: Provide complete perimeter seals. Provide flexible top seal, flexible jamb seal and U shaped bottom seal.

4.D. Door Construction: 4.D.1. Panels: Foamed in place Polyurethane core construction between exterior and interior steel skins. 4.D.2. Steel Skins: Formed from roll formed commercial or drawing quality steel sheet, hot-dip galvanized per ASTM A 924/A 924M and ASTM A 653/A 653M, pre-painted with primer and baked-on polyester topcoat; sections formed to create weather tight tongue-in- groove meeting joint. 4.D.3. Reinforcing: Galvanized and primed steel reinforcement located under each hinge location, pre-punched for hinge attachment. 4.D.4. Handle: High impact polymer step plate/lift handle on bottom panel section. 4.D.5. Track: 4.D.5.a. Vertical Track: 2 inches (50 mm) wide, minimum 0.061 inch (1.55mm) galvanized steel tapered and mounted for wedge type closing. 4.D.5.b. Vertical Track: 3 inches (75 mm) wide, minimum 0.099 inch (2.52 mm) galvanized steel tapered and mounted for wedge type closing. 4.D.5.c. Horizontal Track: 2 inches (50 mm) wide, minimum 0.075 inch (1.91 mm) galvanized steel, reinforced with minimum 0.0897 inch (2.28 mm) galvanized steel angles as required. 4.D.5.d. Horizontal Track: 3 inches (50 mm) wide, minimum 0.099 inch (2.52 mm) galvanized steel, reinforced with minimum 0.0897 inch (2.28 mm) galvanized steel angles as required. 4.D.5.e. Provide standard lift tracks with 15 inches (381 mm) radius track as indicated. 4.D.5.f. Provide vertical lift tracks as indicated. 4.D.5.g. Provide high lift tracks as indicated. 4.D.5.h. Provide tracks that follow roof slope tracks as indicated. 4.D.5.i. Provide low headroom tracks as indicated. 4.D.6. Spring Counterbalance: Torsion spring counterbalance mechanism sized to weight of the door, with a helically wound, oil tempered torsion spring mounted on a steel shaft; cable 08360-21 drum of die cast aluminum with high strength galvanized aircraft cable with minimum 7 to 1 safety factor. 4.D.6.a. Standard Cycle Spring: 10,000 cycle. 4.D.6.b. High Cycle Spring: 25,000 cycles. 4.D.6.c. High Cycle Spring: 50,000 cycles. 4.D.6.d. High Cycle Spring: 100,000 cycles. 4.D.7. Break-Away Bottom Section: Integral part of door; with fiberglass or 1/8 inch (3 mm) polycarbonate lined bottom section with flexible neoprene rubber side edges; exterior to match door face. 4.D.7.a. Single breakaway bottom section for doors up to 20 feet (6 m) wide. 4.D.7.b. Double breakaway bottom section for doors up to 14 feet (4.3 m) wide.

2.5 RAISED PANEL STEEL DOORS, THERMALLY-BROKEN, POLYURETHANE INSULATED

5.A. Premium Duty Insulated 2-inches (51 mm) Door: Clopay Model 3723. 5.A.1. Style: Raised panel steel doors, thermally-broken, polyurethane insulated. 5.A.2. Maximum Door Size: 24 feet, 2 inches (7.4 m) wide by 18 feet (5.5 m) high. 5.A.3. Steel Skin Thickness: Minimum 27 gauge 0.016 inch (0.40 mm) exterior; minimum 28 gauge 0.015 inch (0.38 mm) interior. 5.A.4. Finish: Interior stucco embossed texture with shallow U ribbed pattern, white interior color. 5.A.5. Exterior: Stucco embossed texture with raised exterior panel and color as follows: 5.A.5.a. White. 5.A.5.b. Glacier White. 5.A.5.c. Almond. 5.A.5.d. Desert Tan. 5.A.5.e. Commercial Tan. 5.A.5.f. Brown. 5.A.5.g. Clopay ColorBlast, a two part paint system utilizing Sherwin Williams Solar reflective Polane Paint system. Sherwin Williams color number SW ______. Paint system shall meet or exceed AAMA 2604 standards. 5.A.6. Overall Panel Thickness: 2-inches (51 mm). 5.A.7. End Stiles: Galvanized steel end stiles, engineered for easy hardware attachment through pre-punched holes. Minimum 18 gauge, 0.045 inch (1.14 mm) thick for single end hinge style and 16 gauge .056 inch (1.42 mm) minimum for double end hinge style. 5.A.8. Astragal: U-shaped flexible PVC in retainer of full-length 0.055 inch (1.4 mm) rigid PVC. 5.A.9. Thermal Resistance (R-value): 18.4 deg F hr sq ft/Btu (3.0 (K sq m)/W); calculated door 08360-22 section R-value in accordance with DASMA TDS-163. 5.A.10. Windows: None. 5.A.11. Window: PVC windows measuring 12 inches by 19-1/2 inches (305 mm by 495 mm): 5.A.11.a. Glazing: 1/8 inch (3 mm) DSB sheet glass. 5.A.11.b. Glazing: 1/8 inch (3 mm) acrylic sheet. 5.A.11.c. Glazing: 1/2 inch (12 mm) insulated glass glazing. 5.A.12. Locking: No Lock. 5.A.13. Locking: Inside spring loaded slide bolt lock on end stile that engages slot in track. 5.A.13.a. Provide one inside slide lock. 5.A.13.b. Provide two inside slide lock. 5.A.13.c. Provide five pin cylinder lock with outside key. 5.A.14. Door Drop Safety Device: Provide brackets designed to stop the fall of the door should lift cables fail. 5.A.15. Weatherstripping: Provide complete perimeter seals. Provide flexible top seal, flexible jamb seal and U shaped bottom seal. 5.A.16. Track: 5.A.16.a. Vertical Track: 2 inches (50 mm) wide, minimum 0.061 inch (1.55mm) galvanized steel tapered and mounted for wedge type closing. 5.A.16.b. Vertical Track: 3 inches (75 mm) wide, minimum 0.099 inch (2.52 mm) galvanized steel tapered and mounted for wedge type closing. 5.A.16.c. Horizontal Track: 2 inches (50 mm) wide, minimum 0.075 inch (1.91 mm) galvanized steel, reinforced with minimum 0.0897 inch (2.28 mm) galvanized steel angles as required. 5.A.16.d. Horizontal Track: 3 inches (50 mm) wide, minimum 0.099 inch (2.52 mm) galvanized steel, reinforced with minimum 0.0897 inch (2.28 mm) galvanized steel angles as required. 5.A.16.e. Provide standard lift tracks with 15 inches (381 mm) radius track as indicated. 5.A.16.f. Provide vertical lift tracks as indicated. 5.A.16.g. Provide high lift tracks as indicated. 5.A.16.h. Provide tracks that follow roof slope tracks as indicated. 5.A.16.i. Provide low headroom tracks as indicated. 5.A.17. Spring Counterbalance: Torsion spring counterbalance mechanism sized to weight of the door, with a helically wound, oil tempered torsion spring mounted on a steel shaft; cable drum of die cast aluminum with high strength galvanized aircraft cable with minimum 7 to 1 safety factor. 5.A.17.a. Standard Cycle Spring: 10,000 cycle. 5.A.17.b. High Cycle Spring: 25,000 cycles. 08360-23 5.A.17.c. High Cycle Spring: 50,000 cycles. 5.A.17.d. High Cycle Spring: 100,000 cycles.

5.B. Door Construction: 5.B.1. Panels: Foamed in place Polyurethane core construction between exterior and interior steel skins. 5.B.2. Steel Skins: Formed from roll formed commercial or drawing quality steel sheet, hot-dip galvanized per ASTM A 924/A 924M and ASTM A 653/A 653M, pre-painted with primer and baked-on polyester topcoat; sections formed to create weather tight tongue-in- groove meeting joint. 5.B.3. Reinforcing: Galvanized and primed steel reinforcement located under each hinge location, pre-punched for hinge attachment. 5.B.4. Handle: High impact polymer step plate/lift handle on bottom panel section.

2.6 STEEL DOORS WITH MINOR RIBS, THERMALLY-BROKEN, POLYSTYRENE INSULATED

6.A. Heavy Duty Door: Clopay Model 3200. 6.A.1. Style: Steel doors with minor ribs, thermally-broken, polystyrene insulated. 6.A.2. Maximum Door Size: 32 feet, 2 inches (9.8 m) wide by 24 feet (7.3 m) high. 6.A.3. Overall Panel Thickness: 2 inches (51 mm). 6.A.4. Steel Skin Thickness: Minimum 24 gauge 0.022 inch (0.56 mm) exterior; minimum 28 gauge 0.015 inch (0.38 mm) interior. 6.A.5. Stiles: Steel pre-painted end stiles, minimum 0.049 inch (1.25 mm) thick, engineered for easy hardware attachment through pre-punched holes. 6.A.6. Bottom panel section reinforced with continuous 0.050 inch (1.27 mm) aluminum astragal retainer with U-shaped flexible PVC astragal. 6.A.7. Thermal Resistance (R-value): 9.1 deg F hr sq ft/Btu (1.6 (K sq m)/W); calculated door section R-value in accordance with DASMA TDS-163. 6.A.8. Windows: None. 6.A.9. Windows: Extruded polypropylene windows measuring 8 inches by 24 inches (200 mm by 600 mm). 6.A.9.a. Glazing: 1 inch nominal (25 mm) insulated glass. 6.A.9.b. Glazing: 1 inch nominal (25 mm) insulated tempered glass. 6.A.9.c. Glazing: 1/4 inch (6 mm) tempered glass. 6.A.10. Windows: Extruded polypropylene windows measuring 12 inches by 24 inches (305 mm by 600 mm). 6.A.10.a. Glazing: 1 inch nominal (25 mm) insulated glass. 6.A.10.b. Glazing: 1 inch nominal (25 mm) insulated tempered glass. 08360-24 6.A.10.c. Glazing: 1/4 inch (6 mm) tempered glass.. 6.A.11. Windows: Full vision aluminum section, pre-painted to match door finish. 6.A.11.a. Glazing: 1/8 inch (3 mm) DSB clear float glass. 6.A.11.b. Glazing: 1/4 inch (6 mm) tempered clear float glass. 6.A.11.c. Glazing: 1/2 inch (13 mm) dual pane insulated glazing. 6.A.11.d. Glazing: 5/8 inch (16mm) triple layer clear polycarbonate glazing. 6.A.11.e. Glazing: 5/8 inch (16mm) triple layer custom color polycarbonate glazing. 6.A.12. Finish: Stucco embossed texture with 0.040 inch (100 mm) minor ribs 4 inches or 5 inches (100 or 125 mm) on center, white interior, exterior as follows: 6.A.12.a. White. 6.A.12.b. Brown. 6.A.12.c. Commercial Tan. 6.A.12.d. Gray. 6.A.12.e. Black 6.A.12.f. Trinar White. 6.A.12.g. Clopay ColorBlast, a two part paint system utilizing Sherwin Williams Solar reflective Polane Paint system. Sherwin Williams color number SW ______. Paint system shall meet or exceed AAMA 2604 standards. 6.A.13. Locking: No Lock. 6.A.14. Locking: Inside spring loaded slide bolt lock on end stile that engages slot in track. 6.A.14.a. Provide one inside slide lock. 6.A.14.b. Provide two inside slide lock. 6.A.14.c. Provide five pin cylinder lock with outside key. 6.A.15. Door Drop Safety Device: Provide brackets designed to stop the fall of the door should lift cables fail . 6.A.16. Weatherstripping: Provide complete perimeter seals. Provide flexible top seal, flexible jamb seal and U shaped bottom seal. 6.A.17. Track: 6.A.17.a. Vertical Track: 2 inches (50 mm) wide, minimum 0.061 inch (1.55mm) galvanized steel tapered and mounted for wedge type closing. 6.A.17.b. Vertical Track: 3 inches (75 mm) wide, minimum 0.099 inch (2.52 mm) galvanized steel tapered and mounted for wedge type closing. 6.A.17.c. Horizontal Track: 2 inches (50 mm) wide, minimum 0.075 inch (1.91 mm) galvanized steel, reinforced with minimum 0.0897 inch (2.28 mm) galvanized steel angles as required. 6.A.17.d. 08360-25 Horizontal Track: 3 inches (50 mm) wide, minimum 0.099 inch (2.52 mm) galvanized steel, reinforced with minimum 0.0897 inch (2.28 mm) galvanized steel angles as required. 6.A.17.e. Provide standard lift tracks with 15 inches (381 mm) radius track as indicated. 6.A.17.f. Provide vertical lift tracks as indicated. 6.A.17.g. Provide high lift tracks as indicated. 6.A.17.h. Provide tracks that follow roof slope tracks as indicated. 6.A.17.i. Provide low headroom tracks as indicated. 6.A.18. Spring Counterbalance: Torsion spring counterbalance mechanism sized to weight of the door, with a helically wound, oil tempered torsion spring mounted on a steel shaft; cable drum of die cast aluminum with high strength galvanized aircraft cable with minimum 7 to 1 safety factor. 6.A.18.a. Standard Cycle Spring: 10,000 cycle. 6.A.18.b. High Cycle Spring: 25,000 cycles. 6.A.18.c. High Cycle Spring: 50,000 cycles. 6.A.18.d. High Cycle Spring: 100,000 cycles. 6.A.19. Break-Away Bottom Section: Integral part of door; with fiberglass or 1/8 inch (3 mm) polycarbonate lined bottom section with flexible neoprene rubber side edges; exterior to match door face. 6.A.19.a. Single breakaway bottom section for doors up to 20 feet (6 m) wide. 6.A.19.b. Double breakaway bottom section for doors up to 14 feet (4.3 m) wide. 6.A.20. Pass Door (Walk-Through Service Door): Integral part of door; 32 inches (813 mm) by 80 inches (2032 mm) with aluminum frame, welded corners, geared hinge, and pneumatic door closer; exterior matching door face; integral shiplap weather seal; keyed dead latch security lock.

6.B. Standard Duty Door: Clopay Model 3150. 6.B.1. Style: Steel doors with minor ribs, thermally-broken, polystyrene insulated. 6.B.2. Maximum Door Size: 18 feet 2 inches (5.54 m) wide by 16 feet (4.88 m) high. 6.B.3. Overall Panel Thickness: 1-3/8 inches (35 mm). 6.B.4. Steel Skin Thickness: Minimum 27 gauge 0.016 inch (0.40 mm) exterior; minimum 28 gauge 0.015 inch (0.38 mm) interior. 6.B.5. Stiles: Steel pre-painted end stiles, minimum 0.034 inch (0.86 mm) thick, engineered for easy hardware attachment through pre-punched holes. 6.B.6. Bottom panel section reinforced with continuous 0.050 inch (1.27 mm) aluminum astragal retainer with U-shaped flexible PVC astragal. 6.B.7. Thermal Resistance (R-value): 6.5 deg F hr sq ft/Btu (1.15 (K sq m)/W); calculated door section R-value in accordance with DASMA TDS-163. 6.B.8. Windows: None. 08360-26 6.B.9. Windows: Extruded polypropylene windows measuring 8 inches by 24 inches (200 mm by 600 mm). 6.B.9.a. Glazing: 1/2 inch (12 mm) insulated glass. 6.B.9.b. Glazing: 1/2 inch (12 mm) insulated tempered glass. 6.B.9.c. Glazing: 1/4 inch (6 mm) tempered glass. 6.B.10. Windows: Extruded polypropylene windows measuring 12 inches by 24 inches (305 mm by 600 mm). 6.B.10.a. Glazing: 1/2 inch (12 mm) insulated glass. 6.B.10.b. Glazing: 1/2 inch (12 mm) insulated tempered glass. 6.B.10.c. Glazing: 1/4 inch (6 mm) tempered glass. 6.B.11. Windows: Full vision aluminum section, pre-painted to match door finish. 6.B.11.a. Glazing: 1/8 inch (3 mm) DSB clear float glass. 6.B.11.b. Glazing: 1/2 inch (13 mm) dual pane insulated glazing. 6.B.12. Finish: Stucco embossed texture with 0.040 inch (100 mm) minor ribs 4 inches or 5 inches (100 or 125 mm) on center, white interior, exterior as follows: 6.B.12.a. White. 6.B.12.b. Brown. 6.B.12.c. Commercial Tan. 6.B.12.d. Gray. 6.B.12.e. Clopay ColorBlast, a two part paint system utilizing Sherwin Williams Solar reflective Polane Paint system. Sherwin Williams color number SW ______. Paint system shall meet or exceed AAMA 2604 standards. 6.B.13. Locking: No Lock. 6.B.14. Locking: Inside spring loaded slide bolt lock on end stile that engages slot in track. 6.B.14.a. Provide one inside slide lock. 6.B.14.b. Provide two inside slide lock. 6.B.14.c. Provide five pin cylinder lock with outside key. 6.B.15. Door Drop Safety Device: Provide brackets designed to stop the fall of the door should lift cables fail . 6.B.16. Weatherstripping: Provide complete perimeter seals. Provide flexible top seal, flexible jamb seal and U shaped bottom seal. 6.B.17. Track: 6.B.17.a. Vertical Track: 2 inches (50 mm) wide, minimum 0.061 inch (1.55mm) galvanized steel tapered and mounted for wedge type closing. 6.B.17.b. Vertical Track: 3 inches (75 mm) wide, minimum 0.099 inch (2.52 mm) galvanized 08360-27 steel tapered and mounted for wedge type closing. 6.B.17.c. Horizontal Track: 2 inches (50 mm) wide, minimum 0.075 inch (1.91 mm) galvanized steel, reinforced with minimum 0.0897 inch (2.28 mm) galvanized steel angles as required. 6.B.17.d. Horizontal Track: 3 inches (50 mm) wide, minimum 0.099 inch (2.52 mm) galvanized steel, reinforced with minimum 0.0897 inch (2.28 mm) galvanized steel angles as required. 6.B.17.e. Provide standard lift tracks with 15 inches (381 mm) radius track as indicated. 6.B.17.f. Provide vertical lift tracks as indicated. 6.B.17.g. Provide high lift tracks as indicated. 6.B.17.h. Provide tracks that follow roof slope tracks as indicated. 6.B.17.i. Provide low headroom tracks as indicated. 6.B.18. Spring Counterbalance: Torsion spring counterbalance mechanism sized to weight of the door, with a helically wound, oil tempered torsion spring mounted on a steel shaft; cable drum of die cast aluminum with high strength galvanized aircraft cable with minimum 7 to 1 safety factor. 6.B.18.a. Standard Cycle Spring: 10,000 cycle. 6.B.18.b. High Cycle Spring: 25,000 cycles. 6.B.18.c. High Cycle Spring: 50,000 cycles. 6.B.18.d. High Cycle Spring: 100,000 cycles.

6.C. Door Construction: 6.C.1. Panels: Sandwich construction of exterior and interior steel skins pressure bonded to an expanded core, with skins separated by a continuous silicone filling forming a thermal break. 6.C.2. Steel Skins: Formed from roll formed commercial or drawing quality steel sheet, hot-dip galvanized per ASTM A 924/A 924M and ASTM A 653/A 653M, pre-painted with primer and baked-on polyester topcoat; sections formed to create weather tight tongue-in- groove meeting joint, unless otherwise specified. 6.C.3. Reinforcing: Galvanized and primed steel reinforcement located under each hinge location, pre-punched for hinge attachment. 6.C.4. Handle: High impact polymer step plate/lift handle on bottom panel section.

2.7 FLUSH STEEL DOORS, THERMALLY-BROKEN, POLYSTYRENE INSULATED

7.A. Premium Duty Door: Clopay Model 3220. 7.A.1. Style: Flush steel doors, thermally-broken, polystyrene insulated. 7.A.2. Maximum Door Size: 32 feet, 2 inches (9.8 m) wide by 24 feet (7.3 m) high. 7.A.3. Overall Panel Thickness: 2 inches (51 mm). 7.A.4. 08360-28 Steel Skin Thickness: Minimum 20 gauge 0.034 inch (0.86 mm) exterior; minimum 28 gauge 0.015 inch (0.38 mm) interior. 7.A.5. Stiles: Steel prepainted end stiles, minimum 0.049 inch (1.25 mm) thick, engineered for easy hardware attachment through prepunched holes. 7.A.6. Bottom panel section reinforced with continuous 0.050 inch (1.27 mm) aluminum astragal retainer with U-shaped flexible PVC astragal. 7.A.7. Thermal Resistance (R-value): 9.1 deg F hr sq ft/Btu (1.6 (K sq m)/W); calculated door section R-value in accordance with DASMA TDS-163. 7.A.8. Windows: None. 7.A.9. Windows: Extruded polypropylene windows measuring 8 inches by 24 inches (200 mm by 600 mm). 7.A.9.a. Glazing: 1 inch nominal (25 mm) insulated glass. 7.A.9.b. Glazing: 1 inch nominal (25 mm) insulated tempered glass. 7.A.9.c. Glazing: 1/4 inch (6 mm) tempered glass. 7.A.10. Windows: Extruded polypropylene windows measuring 12 inches by 24 inches (305 mm by 600 mm). 7.A.10.a. Glazing: 1 inch nominal (25 mm) insulated glass. 7.A.10.b. Glazing: 1 inch nominal (25 mm) insulated tempered glass. 7.A.10.c. Glazing: 1/4 inch (6 mm) tempered glass. 7.A.11. Windows: Full vision aluminum section, pre-painted to match door finish. 7.A.11.a. Glazing: 1/8 inch (3 mm) DSB clear float glass. 7.A.11.b. Glazing: 1/4 inch (6 mm) tempered clear float glass. 7.A.11.c. Glazing: 1/2 inch (13 mm) dual pane insulated glazing. 7.A.11.d. Glazing: 5/8 inch (16mm) triple layer clear polycarbonate glazing. 7.A.11.e. Glazing: 5/8 inch (16mm) triple layer custom color polycarbonate glazing. 7.A.12. Finish: Stucco embossed texture, white interior, exterior as follows: 7.A.12.a. White. 7.A.12.b. Brown. 7.A.12.c. Clopay ColorBlast, a two part paint system utilizing Sherwin Williams Solar reflective Polane Paint system. Sherwin Williams color number SW ______. Paint system shall meet or exceed AAMA 2604 standards. 7.A.13. Locking: No Lock. 7.A.14. Locking: Inside spring loaded slide bolt lock on end stile that engages slot in track. 7.A.14.a. Provide one inside slide lock. 7.A.14.b. Provide two inside slide lock. 7.A.14.c. 08360-29 Provide five pin cylinder lock with outside key. 7.A.15. Door Drop Safety Device: Provide brackets designed to stop the fall of the door should lift cables fail 7.A.16. Weatherstripping: Provide complete perimeter seals. Provide flexible top seal, flexible jamb seal and U shaped bottom seal. 7.A.17. Track: 7.A.17.a. Vertical Track: 2 inches (50 mm) wide, minimum 0.061 inch (1.55mm) galvanized steel tapered and mounted for wedge type closing. 7.A.17.b. Vertical Track: 3 inches (75 mm) wide, minimum 0.099 inch (2.52 mm) galvanized steel tapered and mounted for wedge type closing. 7.A.17.c. Horizontal Track: 2 inches (50 mm) wide, minimum 0.075 inch (1.91 mm) galvanized steel, reinforced with minimum 0.0897 inch (2.28 mm) galvanized steel angles as required. 7.A.17.d. Horizontal Track: 3 inches (50 mm) wide, minimum 0.099 inch (2.52 mm) galvanized steel, reinforced with minimum 0.0897 inch (2.28 mm) galvanized steel angles as required. 7.A.17.e. Provide standard lift tracks with 15 inches (381 mm) radius track as indicated. 7.A.17.f. Provide vertical lift tracks as indicated. 7.A.17.g. Provide high lift tracks as indicated. 7.A.17.h. Provide tracks that follow roof slope tracks as indicated. 7.A.17.i. Provide low headroom tracks as indicated. 7.A.18. Spring Counterbalance: Torsion spring counterbalance mechanism sized to weight of the door, with a helically wound, oil tempered torsion spring mounted on a steel shaft; cable drum of die cast aluminum with high strength galvanized aircraft cable with minimum 7 to 1 safety factor. 7.A.18.a. Standard Cycle Spring: 10,000 cycle. 7.A.18.b. High Cycle Spring: 25,000 cycles. 7.A.18.c. High Cycle Spring: 50,000 cycles. 7.A.18.d. High Cycle Spring: 100,000 cycles. 7.A.19. Break-Away Bottom Section: Integral part of door; with fiberglass or 1/8 inch (3 mm) polycarbonate lined bottom section with flexible neoprene rubber side edges; exterior to match door face. 7.A.19.a. Single breakaway bottom section for doors up to 20 feet (6 m) wide. 7.A.19.b. Double breakaway bottom section for doors up to 14 feet (4.3 m) wide. 7.A.20. Pass Door (Walk-Through Service Door): Integral part of door; 32 inches (813 mm) by 80 inches (2032 mm) with aluminum frame, welded corners, geared hinge, and pneumatic door closer; exterior matching door face; integral shiplap weather seal; keyed dead latch security lock.

7.B. Heavy Duty Door: Clopay Model 3211. 08360-30 7.B.1. Style: Flush woodgrain embossed steel doors, thermally-broken, polystyrene insulated. 7.B.2. Maximum Door Size: 24 feet, 2 inches (7.4 m) wide by 18 feet (5.5 m) high. 7.B.3. Overall Panel Thickness: 2 inches (51 mm). 7.B.4. Steel Skin Thickness: Minimum 24 gauge 0.022 inch (0.56 mm) exterior; minimum 28 gauge 0.015 inch (0.38 mm) interior. 7.B.5. Stiles: Steel prepainted end stiles, minimum 0.049 inch (1.25 mm) thick, engineered for easy hardware attachment through pre-punched holes. 7.B.6. Thermal Resistance (R-value): 9.1 deg F hr sq ft/Btu (1.6 (K sq m)/W); calculated door section R-value in accordance with DASMA TDS-163. 7.B.7. Windows: None. 7.B.8. Window: PVC windows measuring 12 inches by 19-1/2 inches (305 mm by 495 mm): 7.B.8.a. Glazing: 1/8 inch (3 mm) DSB sheet glass. 7.B.8.b. Glazing: 1/8 inch (3 mm) acrylic sheet. 7.B.8.c. Glazing: 1/2 inch (12 mm) insulated glass glazing. 7.B.9. Finish: Flush exterior design with wood grain embossment, white interior and exterior as follows: 7.B.9.a. White. 7.B.9.b. Brown. 7.B.9.c. Almond. 7.B.9.d. Desert Tan. 7.B.9.e. Sandtone. 7.B.9.f. Trinar White. 7.B.9.g. Trinar Beige. 7.B.9.h. Clopay ColorBlast, a two part paint system utilizing Sherwin Williams Solar reflective Polane Paint system. Sherwin Williams color number SW ______. Paint system shall meet or exceed AAMA 2604 standards. 7.B.10. Locking: No Lock. 7.B.11. Locking: Inside spring loaded slide bolt lock on end stile that engages slot in track. 7.B.11.a. Provide one inside slide lock. 7.B.11.b. Provide two inside slide lock. 7.B.11.c. Provide five pin cylinder lock with outside key. 7.B.12. Door Drop Safety Device: Provide brackets designed to stop the fall of the door should lift cables fail . 7.B.13. Weatherstripping: Provide complete perimeter seals. Provide flexible top seal, flexible jamb seal and U shaped bottom seal. 08360-31 7.B.14. Track: 7.B.14.a. Vertical Track: 2 inches (50 mm) wide, minimum 0.061 inch (1.55mm) galvanized steel tapered and mounted for wedge type closing. 7.B.14.b. Vertical Track: 3 inches (75 mm) wide, minimum 0.099 inch (2.52 mm) galvanized steel tapered and mounted for wedge type closing. 7.B.14.c. Horizontal Track: 2 inches (50 mm) wide, minimum 0.075 inch (1.91 mm) galvanized steel, reinforced with minimum 0.0897 inch (2.28 mm) galvanized steel angles as required. 7.B.14.d. Horizontal Track: 3 inches (50 mm) wide, minimum 0.099 inch (2.52 mm) galvanized steel, reinforced with minimum 0.0897 inch (2.28 mm) galvanized steel angles as required. 7.B.14.e. Provide standard lift tracks with 15 inches (381 mm) radius track as indicated. 7.B.14.f. Provide vertical lift tracks as indicated. 7.B.14.g. Provide high lift tracks as indicated. 7.B.14.h. Provide tracks that follow roof slope tracks as indicated. 7.B.14.i. Provide low headroom tracks as indicated. 7.B.15. Spring Counterbalance: Torsion spring counterbalance mechanism sized to weight of the door, with a helically wound, oil tempered torsion spring mounted on a steel shaft; cable drum of die cast aluminum with high strength galvanized aircraft cable with minimum 7 to 1 safety factor. 7.B.15.a. Standard Cycle Spring: 10,000 cycle. 7.B.15.b. High Cycle Spring: 25,000 cycles. 7.B.15.c. High Cycle Spring: 50,000 cycles. 7.B.15.d. High Cycle Spring: 100,000 cycles.

7.C. Standard Duty Door: Clopay Model 3155. 7.C.1. Style: Flush woodgrain embossed steel doors, thermally-broken, polystyrene insulated. 7.C.2. Maximum Door Size: 18 feet 2 inches (5.54 m) wide by 16 feet (4.88 m) high. 7.C.3. Overall Panel Thickness: 1-3/8 inches (35 mm). 7.C.4. Steel Skin Thickness: Minimum 27 gauge 0.016 inch (0.40 mm) exterior; minimum 28 gauge 0.015 inch (0.38 mm) interior. 7.C.5. Stiles: Steel pre-painted end stiles, minimum 0.034 inch (0.86 mm) thick, engineered for easy hardware attachment through pre-punched holes. 7.C.6. Bottom panel section reinforced with continuous 0.050 inch (1.27 mm) aluminum astragal retainer with U-shaped flexible PVC astragal. 7.C.7. Thermal Resistance (R-value): 6.5 deg F hr sq ft/Btu (1.15 (K sq m)/W); calculated door section R-value in accordance with DASMA TDS-163. 7.C.8. Windows: None. 08360-32 7.C.9. Window: PVC windows measuring 12 inches by 19-1/2 inches (305 mm by 495 mm): 7.C.9.a. Glazing: 1/8 inch (3 mm) DSB sheet glass. 7.C.9.b. Glazing: 1/8 inch (3 mm) acrylic sheet. 7.C.9.c. Glazing: 1/2 inch (12 mm) insulated glass glazing. 7.C.10. Finish: Wood grained embossed texture with flush panel, white interior, exterior as follows: 7.C.10.a. White. 7.C.10.b. Brown. 7.C.10.c. Almond. 7.C.10.d. Sandtone. 7.C.10.e. Bronze. 7.C.10.f. Gray. 7.C.10.g. Clopay ColorBlast, a two part paint system utilizing Sherwin Williams Solar reflective Polane Paint system. Sherwin Williams color number SW ______. Paint system shall meet or exceed AAMA 2604 standards. 7.C.11. Locking: No Lock. 7.C.12. Locking: Inside spring loaded slide bolt lock on end stile that engages slot in track. 7.C.12.a. Provide one inside slide lock. 7.C.12.b. Provide two inside slide lock. 7.C.12.c. Provide five pin cylinder lock with outside key. 7.C.13. Door Drop Safety Device: Provide brackets designed to stop the fall of the door should lift cables fail. 7.C.14. Weatherstripping: Provide complete perimeter seals. Provide flexible top seal, flexible jamb seal and U shaped bottom seal. 7.C.15. Track: 7.C.15.a. Vertical Track: 2 inches (50 mm) wide, minimum 0.061 inch (1.55mm) galvanized steel tapered and mounted for wedge type closing. 7.C.15.b. Vertical Track: 3 inches (75 mm) wide, minimum 0.099 inch (2.52 mm) galvanized steel tapered and mounted for wedge type closing. 7.C.15.c. Horizontal Track: 2 inches (50 mm) wide, minimum 0.075 inch (1.91 mm) galvanized steel, reinforced with minimum 0.0897 inch (2.28 mm) galvanized steel angles as required. 7.C.15.d. Horizontal Track: 3 inches (50 mm) wide, minimum 0.099 inch (2.52 mm) galvanized steel, reinforced with minimum 0.0897 inch (2.28 mm) galvanized steel angles as required. 7.C.15.e. Provide standard lift tracks with 15 inches (381 mm) radius track as indicated. 7.C.15.f. 08360-33 Provide vertical lift tracks as indicated. 7.C.15.g. Provide high lift tracks as indicated. 7.C.15.h. Provide tracks that follow roof slope tracks as indicated. 7.C.15.i. Provide low headroom tracks as indicated. 7.C.16. Spring Counterbalance: Torsion spring counterbalance mechanism sized to weight of the door, with a helically wound, oil tempered torsion spring mounted on a steel shaft; cable drum of die cast aluminum with high strength galvanized aircraft cable with minimum 7 to 1 safety factor. 7.C.16.a. Standard Cycle Spring: 10,000 cycle. 7.C.16.b. High Cycle Spring: 25,000 cycles. 7.C.16.c. High Cycle Spring: 50,000 cycles. 7.C.16.d. High Cycle Spring: 100,000 cycles.

7.D. Door Construction: 7.D.1. Panels: Sandwich construction of exterior and interior steel skins pressure bonded to an expanded core, with skins separated by a continuous silicone filling forming a thermal break. 7.D.2. Steel Skins: Formed from roll formed commercial or drawing quality steel sheet, hot-dip galvanized per ASTM A 924/A 924M and ASTM A 653/A 653M, pre-painted with primer and baked-on polyester topcoat; sections formed to create weather tight tongue-in- groove meeting joint, unless otherwise specified. 7.D.3. Reinforcing: Galvanized and primed steel reinforcement located under each hinge location, pre-punched for hinge attachment. 7.D.4. Handle: High impact polymer step plate/lift handle on bottom panel section.

2.8 RAISED PANEL STEEL DOORS, THERMALLY-BROKEN, POLYSTYRENE INSULATED

8.A. Heavy Duty Door: Clopay Model 3213. 8.A.1. Style: Raised panel wood grain embossed steel doors, thermally-broken, polystyrene insulated. 8.A.2. Maximum Door Size: 24 feet, 2 inches (7.4 m) wide by 18 feet (5.5 m) high. 8.A.3. Overall Panel Thickness: 2 inches (51 mm). 8.A.4. Steel Skin Thickness: Minimum 24 gauge 0.022 inch (0.56 mm) exterior; minimum 28 gauge 0.015 inch (0.38 mm) interior. 8.A.5. Stiles: Steel prepainted end stiles, minimum 0.049 inch (1.25 mm) thick, engineered for easy hardware attachment through pre-punched holes. 8.A.6. Thermal Resistance (R-value): 9.1 deg F hr sq ft/Btu (1.6 (K sq m)/W); calculated door section R-value in accordance with DASMA TDS-163. 8.A.7. Windows: None. 8.A.8. 08360-34 Window: PVC windows measuring 12 inches by 19-1/2 inches (305 mm by 495 mm): 8.A.8.a. Glazing: 1/8 inch (3 mm) DSB sheet glass. 8.A.8.b. Glazing: 1/8 inch (3 mm) acrylic sheet. 8.A.8.c. Glazing: 1/2 inch (12 mm) insulated glass glazing. 8.A.9. Finish: Raised panel exterior design, white interior and exterior as follows: 8.A.9.a. White. 8.A.9.b. Brown. 8.A.9.c. Almond. 8.A.9.d. Desert Tan. 8.A.9.e. Sandtone. 8.A.9.f. Trinar White. 8.A.9.g. Trinar Beige. 8.A.9.h. Clopay ColorBlast, a two part paint system utilizing Sherwin Williams Solar reflective Polane Paint system. Sherwin Williams color number SW ______. Paint system shall meet or exceed AAMA 2604 standards. 8.A.10. Locking: No Lock. 8.A.11. Locking: Inside spring loaded slide bolt lock on end stile that engages slot in track. 8.A.11.a. Provide one inside slide lock. 8.A.11.b. Provide two inside slide lock. 8.A.11.c. Provide five pin cylinder lock with outside key. 8.A.12. Door Drop Safety Device: Provide brackets designed to stop the fall of the door should lift cables fail. 8.A.13. Weatherstripping: Provide complete perimeter seals. Provide flexible top seal, flexible jamb seal and U shaped bottom seal. 8.A.14. Track: 8.A.14.a. Vertical Track: 2 inches (50 mm) wide, minimum 0.061 inch (1.55mm) galvanized steel tapered and mounted for wedge type closing. 8.A.14.b. Vertical Track: 3 inches (75 mm) wide, minimum 0.099 inch (2.52 mm) galvanized steel tapered and mounted for wedge type closing. 8.A.14.c. Horizontal Track: 2 inches (50 mm) wide, minimum 0.075 inch (1.91 mm) galvanized steel, reinforced with minimum 0.0897 inch (2.28 mm) galvanized steel angles as required. 8.A.14.d. Horizontal Track: 3 inches (50 mm) wide, minimum 0.099 inch (2.52 mm) galvanized steel, reinforced with minimum 0.0897 inch (2.28 mm) galvanized steel angles as required. 8.A.14.e. Provide standard lift tracks with 15 inches (381 mm) radius track as indicated. 8.A.14.f. 08360-35 Provide vertical lift tracks as indicated. 8.A.14.g. Provide high lift tracks as indicated. 8.A.14.h. Provide tracks that follow roof slope tracks as indicated. 8.A.14.i. Provide low headroom tracks as indicated. 8.A.15. Spring Counterbalance: Torsion spring counterbalance mechanism sized to weight of the door, with a helically wound, oil tempered torsion spring mounted on a steel shaft; cable drum of die cast aluminum with high strength galvanized aircraft cable with minimum 7 to 1 safety factor. 8.A.15.a. Standard Cycle Spring: 10,000 cycle. 8.A.15.b. High Cycle Spring: 25,000 cycles. 8.A.15.c. High Cycle Spring: 50,000 cycles. 8.A.15.d. High Cycle Spring: 100,000 cycles.

8.B. Standard Duty Door: Clopay Model 3154. 8.B.1. Style: Raised panel woodgrain embossed steel doors, thermally-broken, polystyrene insulated. 8.B.2. Maximum Door Size: 18 feet 2 inches (5.54 m) wide by 16 feet (4.88 m) high. 8.B.3. Overall Panel Thickness: 1-3/8 inches (35 mm). 8.B.4. Steel Skin Thickness: Minimum 27 gauge 0.016 inch (0.40 mm) exterior; minimum 28 gauge 0.015 inch (0.38 mm) interior. 8.B.5. Stiles: Steel pre-painted end stiles, minimum 0.034 inch (0.86 mm) thick, engineered for easy hardware attachment through pre-punched holes. 8.B.6. Bottom panel section reinforced with continuous 0.050 inch (1.27 mm) aluminum astragal retainer with U-shaped flexible PVC astragal. 8.B.7. Thermal Resistance (R-value): 6.5 deg F hr sq ft/Btu (1.15 (K sq m)/W); calculated door section R-value in accordance with DASMA TDS-163. 8.B.8. Windows: None. 8.B.9. Window: PVC windows measuring 12 inches by 19-1/2 inches (305 mm by 495 mm): 8.B.9.a. Glazing: 1/8 inch (3 mm) DSB sheet glass. 8.B.9.b. Glazing: 1/8 inch (3 mm) acrylic sheet. 8.B.9.c. Glazing: 1/2 inch (12 mm) insulated glass glazing. 8.B.10. Finish: Wood grain embossed texture with 0.040 inch (100 mm) elegant raised panel, exterior as follows: 8.B.10.a. White. 8.B.10.b. Brown. 8.B.10.c. Almond. 8.B.10.d. 08360-36 Sandtone. 8.B.10.e. Bronze. 8.B.10.f. Gray. 8.B.10.g. Clopay ColorBlast, a two part paint system utilizing Sherwin Williams Solar reflective Polane Paint system. Sherwin Williams color number SW ______. Paint system shall meet or exceed AAMA 2604 standards. 8.B.11. Locking: No Lock. 8.B.12. Locking: Inside spring loaded slide bolt lock on end stile that engages slot in track. 8.B.12.a. Provide one inside slide lock. 8.B.12.b. Provide two inside slide lock. 8.B.12.c. Provide five pin cylinder lock with outside key. 8.B.13. Door Drop Safety Device: Provide brackets designed to stop the fall of the door should lift cables fail. 8.B.14. Weatherstripping: Provide complete perimeter seals. Provide flexible top seal, flexible jamb seal and U shaped bottom seal. 8.B.15. Track: 8.B.15.a. Vertical Track: 2 inches (50 mm) wide, minimum 0.061 inch (1.55mm) galvanized steel tapered and mounted for wedge type closing. 8.B.15.b. Vertical Track: 3 inches (75 mm) wide, minimum 0.099 inch (2.52 mm) galvanized steel tapered and mounted for wedge type closing. 8.B.15.c. Horizontal Track: 2 inches (50 mm) wide, minimum 0.075 inch (1.91 mm) galvanized steel, reinforced with minimum 0.0897 inch (2.28 mm) galvanized steel angles as required. 8.B.15.d. Horizontal Track: 3 inches (50 mm) wide, minimum 0.099 inch (2.52 mm) galvanized steel, reinforced with minimum 0.0897 inch (2.28 mm) galvanized steel angles as required. 8.B.15.e. Provide standard lift tracks with 15 inches (381 mm) radius track as indicated. 8.B.15.f. Provide vertical lift tracks as indicated. 8.B.15.g. Provide high lift tracks as indicated. 8.B.15.h. Provide tracks that follow roof slope tracks as indicated. 8.B.15.i. Provide low headroom tracks as indicated. 8.B.16. Spring Counterbalance: Torsion spring counterbalance mechanism sized to weight of the door, with a helically wound, oil tempered torsion spring mounted on a steel shaft; cable drum of die cast aluminum with high strength galvanized aircraft cable with minimum 7 to 1 safety factor. 8.B.16.a. Standard Cycle Spring: 10,000 cycle. 8.B.16.b. High Cycle Spring: 25,000 cycles. 8.B.16.c. High Cycle Spring: 50,000 cycles. 08360-37 8.B.16.d. High Cycle Spring: 100,000 cycles.

8.C. Door Construction: 8.C.1. Panels: Sandwich construction comprising exterior and interior steel skins pressure bonded to an expanded core, with the skins separated by a continuous silicone filling that forms a thermal break. 8.C.2. Steel Skins: Formed from roll formed commercial or drawing quality steel sheet, hot-dip galvanized per ASTM A 924/A 924M and ASTM A 653/A 653M, pre-painted with primer and baked-on polyester topcoat; sections formed to create weather tight tongue-in- groove meeting joint, unless otherwise specified 8.C.3. Reinforcing: Galvanized and primed steel reinforcement located under each hinge location, pre-punched for hinge attachment. 8.C.4. Handle: Galvanized steel step plate/lift handle on bottom panel section.

2.9 DEEP RIBBED STEEL DOORS, POLYSTYRENE INSULATED

9.A. Premium Duty Door: Clopay Model 520S. 9.A.1. Style: Deep ribbed steel doors, insulated. 9.A.2. Maximum Door Size: 32 feet, 2 inches (9.8 m) wide and 26 feet (7.92 m) high. 9.A.3. Interior pre-painted 30 gauge steel back cover. 9.A.4. Exterior Steel Skin Thickness: Minimum 20 gauge 0.034 inch (0.86 mm). 9.A.5. Windows: None. 9.A.6. Windows: 24 inches by 6 inches (150 mm by 610 mm) with polypropylene frame to match door color. 9.A.6.a. Glazing:1/8 inch (3 mm) DSB clear float glass. 9.A.6.b. Glazing: 1/4 inch (6 mm) tempered clear float glass. 9.A.6.c. Glazing: 1/2 inch (13 mm) dual pane insulated glazing. 9.A.7. Windows: 24 inches by 12 inches (610 mm by 300 mm) with polypropylene frame to match door color. 9.A.7.a. Glazing: 1/8 inch (3 mm) DSB clear float glass. 9.A.7.b. Glazing: 1/4 inch (6 mm) tempered clear float glass. 9.A.7.c. Glazing: 1/2 inch (13 mm) dual pane insulated glazing. 9.A.8. Windows: Full-view sections, pre-painted to match door finish. 9.A.8.a. Glazing: 1/8 inch (3 mm) DSB clear float glass. 9.A.8.b. Glazing: 1/4 inch (6 mm) tempered clear float glass. 9.A.8.c. Glazing: 1/2 inch (13 mm) dual pane insulated glazing. 9.A.9. 08360-38 Finish: Exterior 1 mil (.025 mm) coating; interior 0.5 mil (0.013 mm) coating; color as follows: 9.A.9.a. White. 9.A.9.b. Brown. 9.A.10. Locking: No Lock. 9.A.11. Locking: Inside spring loaded slide bolt lock on end stile that engages slot in track. 9.A.11.a. Provide one inside slide lock. 9.A.11.b. Provide two inside slide lock. 9.A.11.c. Provide five pin cylinder lock with outside key. 9.A.12. Door Drop Safety Device: Provide brackets designed to stop the fall of the door should lift cables fail. 9.A.13. Weatherstripping: Provide complete perimeter seals. Provide flexible top seal, flexible jamb seal and U shaped bottom seal. 9.A.14. Track: 9.A.14.a. Vertical Track: 2 inches (50 mm) wide, minimum 0.061 inch (1.55mm) galvanized steel tapered and mounted for wedge type closing. 9.A.14.b. Vertical Track: 3 inches (75 mm) wide, minimum 0.099 inch (2.52 mm) galvanized steel tapered and mounted for wedge type closing. 9.A.14.c. Horizontal Track: 2 inches (50 mm) wide, minimum 0.075 inch (1.91 mm) galvanized steel, reinforced with minimum 0.0897 inch (2.28 mm) galvanized steel angles as required. 9.A.14.d. Horizontal Track: 3 inches (50 mm) wide, minimum 0.099 inch (2.52 mm) galvanized steel, reinforced with minimum 0.0897 inch (2.28 mm) galvanized steel angles as required. 9.A.14.e. Provide standard lift tracks with 15 inches (381 mm) radius track as indicated. 9.A.14.f. Provide vertical lift tracks as indicated. 9.A.14.g. Provide high lift tracks as indicated. 9.A.14.h. Provide tracks that follow roof slope tracks as indicated. 9.A.14.i. Provide low headroom tracks as indicated. 9.A.15. Spring Counterbalance: Torsion spring counterbalance mechanism sized to weight of the door, with a helically wound, oil tempered torsion spring mounted on a steel shaft; cable drum of die cast aluminum with high strength galvanized aircraft cable with minimum 7 to 1 safety factor. 9.A.15.a. Standard Cycle Spring: 10,000 cycle. 9.A.15.b. High Cycle Spring: 25,000 cycles. 9.A.15.c. High Cycle Spring: 50,000 cycles. 9.A.15.d. High Cycle Spring: 100,000 cycles. 9.A.16. 08360-39 Break-Away Bottom Section: Integral part of door; with fiberglass or 1/8 inch (3 mm) polycarbonate lined bottom section with flexible neoprene rubber side edges; exterior to match door face. 9.A.16.a. Single breakaway bottom section for doors up to 20 feet (6 m) wide. 9.A.16.b. Double breakaway bottom section for doors up to 14 feet (4.3 m) wide. 9.A.17. Pass Door (Walk-Through Service Door): Integral part of door; 32 inches (813 mm) by 80 inches (2032 mm) with aluminum frame, welded corners, geared hinge, and pneumatic door closer; exterior matching door face; integral shiplap weather seal; keyed dead latch security lock.

9.B. Heavy Duty Door: Clopay Model 524S. 9.B.1. Style: Deep ribbed steel doors, insulated. 9.B.2. Steel Backer Cover: Interior pre-painted 30 gauge steel back cover. 9.B.3. Maximum Door Size: 26 feet, 2 inches (7.97 m) wide and 24 ft (7.31 m) high. 9.B.4. Exterior Steel Skin Thickness: Minimum 24 gauge 0.022 inch (0.56 mm). 9.B.5. Windows: None. 9.B.6. Windows: 24 inches by 6 inches (150 mm by 610 mm) with polypropylene frame to match door color. 9.B.6.a. Glazing: 1/8 inch (3 mm) DSB clear float glass. 9.B.6.b. Glazing: 1/4 inch (6 mm) tempered clear float glass. 9.B.6.c. Glazing: 1/2 inch (13 mm) dual pane insulated glazing. 9.B.7. Windows: 24 inches by 12 inches (610 mm by 300 mm) with polypropylene frame to match door color. 9.B.7.a. Glazing: 1/8 inch (3 mm) DSB clear float glass. 9.B.7.b. Glazing: 1/4 inch (6 mm) tempered clear float glass. 9.B.7.c. Glazing: 1/2 inch (13 mm) dual pane insulated glazing. 9.B.8. Windows: Full-view sections, prepainted to match door finish. 9.B.8.a. Glazing: 1/8 inch (3 mm) DSB clear float glass. 9.B.8.b. Glazing: 1/4 inch (6 mm) tempered clear float glass. 9.B.8.c. Glazing: 1/2 inch (13 mm) dual pane insulated glazing. 9.B.9. Finish: Exterior 1 mil (.025 mm) coating; interior 0.5 mil (0.013 mm) coating; color as follows: 9.B.9.a. White. 9.B.9.b. Brown. 9.B.9.c. Tan. 9.B.9.d. Gray. 08360-40 9.B.9.e. Trinar White. 9.B.10. Locking: No Lock. 9.B.11. Locking: Inside spring loaded slide bolt lock on end stile that engages slot in track. 9.B.11.a. Provide one inside slide lock. 9.B.11.b. Provide two inside slide lock. 9.B.11.c. Provide five pin cylinder lock with outside key. 9.B.12. Door Drop Safety Device: Provide brackets designed to stop the fall of the door should lift cables fail. 9.B.13. Weatherstripping: Provide complete perimeter seals. Provide flexible top seal, flexible jamb seal and U shaped bottom seal. 9.B.14. Track: 9.B.14.a. Vertical Track: 2 inches (50 mm) wide, minimum 0.061 inch (1.55mm) galvanized steel tapered and mounted for wedge type closing. 9.B.14.b. Vertical Track: 3 inches (75 mm) wide, minimum 0.099 inch (2.52 mm) galvanized steel tapered and mounted for wedge type closing. 9.B.14.c. Horizontal Track: 2 inches (50 mm) wide, minimum 0.075 inch (1.91 mm) galvanized steel, reinforced with minimum 0.0897 inch (2.28 mm) galvanized steel angles as required. 9.B.14.d. Horizontal Track: 3 inches (50 mm) wide, minimum 0.099 inch (2.52 mm) galvanized steel, reinforced with minimum 0.0897 inch (2.28 mm) galvanized steel angles as required. 9.B.14.e. Provide standard lift tracks with 15 inches (381 mm) radius track as indicated. 9.B.14.f. Provide vertical lift tracks as indicated. 9.B.14.g. Provide high lift tracks as indicated. 9.B.14.h. Provide tracks that follow roof slope tracks as indicated. 9.B.14.i. Provide low headroom tracks as indicated. 9.B.15. Spring Counterbalance: Torsion spring counterbalance mechanism sized to weight of the door, with a helically wound, oil tempered torsion spring mounted on a steel shaft; cable drum of die cast aluminum with high strength galvanized aircraft cable with minimum 7 to 1 safety factor. 9.B.15.a. Standard Cycle Spring: 10,000 cycle. 9.B.15.b. High Cycle Spring: 25,000 cycles. 9.B.15.c. High Cycle Spring: 50,000 cycles. 9.B.15.d. High Cycle Spring: 100,000 cycles. 9.B.16. Break-Away Bottom Section: Integral part of door; with fiberglass or 1/8 inch (3 mm) polycarbonate lined bottom section with flexible neoprene rubber side edges; exterior to match door face. 9.B.16.a. 08360-41 Single breakaway bottom section for doors up to 20 feet (6 m) wide. 9.B.16.b. Double breakaway bottom section for doors up to 14 feet (4.3 m) wide. 9.B.17. Pass Door (Walk-Through Service Door): Integral part of door; 32 inches (813 mm) by 80 inches (2032 mm) with aluminum frame, welded corners, geared hinge, and pneumatic door closer; exterior matching door face; integral shiplap weather seal; keyed dead latch security lock.

9.C. Heavy Duty Door: Clopay Model 524V. 9.C.1. Style: Deep ribbed steel doors, insulated. 9.C.2. Interior polyethylene vinyl back cover. 9.C.3. Maximum Door Size: 26 feet, 2 inches (7.97 m) wide and 24 ft (7.31 m) high. 9.C.4. Exterior Steel Skin Thickness: Minimum 24 gauge 0.022 inch (0.56 mm). 9.C.5. Windows: None. 9.C.6. Windows: 24 inches by 6 inches (150 mm by 610 mm) with polypropylene frame to match door color. 9.C.6.a. Glazing: 1/8 inch (3 mm) DSB clear float glass. 9.C.6.b. Glazing: 1/4 inch (6 mm) tempered clear float glass. 9.C.6.c. Glazing: 1/2 inch (13 mm) dual pane insulated glazing. 9.C.7. Windows: 24 inches by 12 inches (610 mm by 300 mm) with polypropylene frame to match door color. 9.C.7.a. Glazing: 1/8 inch (3 mm) DSB clear float glass. 9.C.7.b. Glazing: 1/4 inch (6 mm) tempered clear float glass. 9.C.7.c. Glazing: 1/2 inch (13 mm) dual pane insulated glazing. 9.C.8. Windows: Full-view sections, prepainted to match door finish. 9.C.8.a. Glazing: 1/8 inch (3 mm) DSB clear float glass. 9.C.8.b. Glazing: 1/4 inch (6 mm) tempered clear float glass. 9.C.8.c. Glazing: 1/2 inch (13 mm) dual pane insulated glazing. 9.C.9. Finish: Exterior 1 mil (.025 mm) coating; interior 0.5 mil (0.013 mm) coating; color as follows: 9.C.9.a. White. 9.C.9.b. Brown. 9.C.9.c. Tan. 9.C.9.d. Gray. 9.C.9.e. Trinar White. 9.C.10. Locking: No Lock. 08360-42 9.C.11. Locking: Inside spring loaded slide bolt lock on end stile that engages slot in track. 9.C.11.a. Provide one inside slide lock. 9.C.11.b. Provide two inside slide lock. 9.C.11.c. Provide five pin cylinder lock with outside key. 9.C.12. Door Drop Safety Device: Provide brackets designed to stop the fall of the door should lift cables fail. 9.C.13. Weatherstripping: Provide complete perimeter seals. Provide flexible top seal, flexible jamb seal and U shaped bottom seal. 9.C.14. Track: 9.C.14.a. Vertical Track: 2 inches (50 mm) wide, minimum 0.061 inch (1.55mm) galvanized steel tapered and mounted for wedge type closing. 9.C.14.b. Vertical Track: 3 inches (75 mm) wide, minimum 0.099 inch (2.52 mm) galvanized steel tapered and mounted for wedge type closing. 9.C.14.c. Horizontal Track: 2 inches (50 mm) wide, minimum 0.075 inch (1.91 mm) galvanized steel, reinforced with minimum 0.0897 inch (2.28 mm) galvanized steel angles as required. 9.C.14.d. Horizontal Track: 3 inches (50 mm) wide, minimum 0.099 inch (2.52 mm) galvanized steel, reinforced with minimum 0.0897 inch (2.28 mm) galvanized steel angles as required. 9.C.14.e. Provide standard lift tracks with 15 inches (381 mm) radius track as indicated. 9.C.14.f. Provide vertical lift tracks as indicated. 9.C.14.g. Provide high lift tracks as indicated. 9.C.14.h. Provide tracks that follow roof slope tracks as indicated. 9.C.14.i. Provide low headroom tracks as indicated. 9.C.15. Spring Counterbalance: Torsion spring counterbalance mechanism sized to weight of the door, with a helically wound, oil tempered torsion spring mounted on a steel shaft; cable drum of die cast aluminum with high strength galvanized aircraft cable with minimum 7 to 1 safety factor. 9.C.15.a. Standard Cycle Spring: 10,000 cycle. 9.C.15.b. High Cycle Spring: 25,000 cycles. 9.C.15.c. High Cycle Spring: 50,000 cycles. 9.C.15.d. High Cycle Spring: 100,000 cycles. 9.C.16. Break-Away Bottom Section: Integral part of door; with fiberglass or 1/8 inch (3 mm) polycarbonate lined bottom section with flexible neoprene rubber side edges; exterior to match door face. 9.C.16.a. Single breakaway bottom section for doors up to 20 feet (6 m) wide. 9.C.16.b. Double breakaway bottom section for doors up to 14 feet (4.3 m) wide. 9.C.17. 08360-43 Pass Door (Walk-Through Service Door): Integral part of door; 32 inches (813 mm) by 80 inches (2032 mm) with aluminum frame, welded corners, geared hinge, and pneumatic door closer; exterior matching door face; integral shiplap weather seal; keyed dead latch security lock.

9.D. Heavy Duty Door: Clopay Model 525S. 9.D.1. Style: Deep ribbed steel doors, insulated. 9.D.2. Maximum Door Size: 20 feet 2 inches (6.15 m) wide and 18 feet (5.5 m) high. 9.D.3. Interior pre-painted 30 gauge steel back cover. 9.D.4. Exterior Steel Skin Thickness: Minimum 25 gauge 0.019 inch (0.48 mm). 9.D.5. Windows: None. 9.D.6. Windows: 24 by 6 inches (610 mm by 152 mm) with polypropylene frame to match door color. 9.D.6.a. Glazing: 1/8 inch (3 mm) DSB sheet glass glazing. 9.D.6.b. Glazing: 1/8 inch (3 mm) tempered sheet glass glazing. 9.D.6.c. Glazing: 1/8 inch (3 mm) acrylic glazing. 9.D.6.d. Glazing: 1/8 inch (3 mm) clear polycarbonate glazing. 9.D.7. Windows: 24 by 12 inch (610 by 300 mm) with polypropylene frame to match door color. 9.D.7.a. Glazing: 1/8 inch (3 mm) DSB sheet glass glazing. 9.D.7.b. Glazing: 1/8 inch (3 mm) tempered sheet glass glazing. 9.D.7.c. Glazing: 1/8 inch (3 mm) acrylic glazing. 9.D.7.d. Glazing: 1/8 inch (3 mm) clear polycarbonate glazing. 9.D.8. Windows: Full-view aluminum sections, pre-painted to match door finish. 9.D.8.a. Glazing: 1/8 inch (3 mm) DSB sheet glass glazing. 9.D.8.b. Glazing: 1/8 inch (3 mm) tempered sheet glass glazing. 9.D.8.c. Glazing: 1/8 inch (3 mm) acrylic glazing. 9.D.8.d. Glazing: 1/8 inch (3 mm) clear polycarbonate glazing. 9.D.9. Finish: Exterior 1 mil (.025 mm) coating; interior 0.5 mil (0.013 mm) coating; color as follows: 9.D.9.a. White. 9.D.9.b. Brown. 9.D.10. Locking: No Lock. 9.D.11. Locking: Inside spring loaded slide bolt lock on end stile that engages slot in track. 9.D.11.a. Provide one inside slide lock. 9.D.11.b. 08360-44 Provide two inside slide lock. 9.D.11.c. Provide five pin cylinder lock with outside key. 9.D.12. Door Drop Safety Device: Provide brackets designed to stop the fall of the door should lift cables fail. 9.D.13. Weatherstripping: Provide complete perimeter seals. Provide flexible top seal, flexible jamb seal and U shaped bottom seal. 9.D.14. Track: 9.D.14.a. Vertical Track: 2 inches (50 mm) wide, minimum 0.061 inch (1.55mm) galvanized steel tapered and mounted for wedge type closing. 9.D.14.b. Vertical Track: 3 inches (75 mm) wide, minimum 0.099 inch (2.52 mm) galvanized steel tapered and mounted for wedge type closing. 9.D.14.c. Horizontal Track: 2 inches (50 mm) wide, minimum 0.075 inch (1.91 mm) galvanized steel, reinforced with minimum 0.0897 inch (2.28 mm) galvanized steel angles as required. 9.D.14.d. Horizontal Track: 3 inches (50 mm) wide, minimum 0.099 inch (2.52 mm) galvanized steel, reinforced with minimum 0.0897 inch (2.28 mm) galvanized steel angles as required. 9.D.14.e. Provide standard lift tracks with 15 inches (381 mm) radius track as indicated. 9.D.14.f. Provide vertical lift tracks as indicated. 9.D.14.g. Provide high lift tracks as indicated. 9.D.14.h. Provide tracks that follow roof slope tracks as indicated. 9.D.14.i. Provide low headroom tracks as indicated. 9.D.15. Spring Counterbalance: Torsion spring counterbalance mechanism sized to weight of the door, with a helically wound, oil tempered torsion spring mounted on a steel shaft; cable drum of die cast aluminum with high strength galvanized aircraft cable with minimum 7 to 1 safety factor. 9.D.15.a. Standard Cycle Spring: 10,000 cycle. 9.D.15.b. High Cycle Spring: 25,000 cycles. 9.D.15.c. High Cycle Spring: 50,000 cycles. 9.D.15.d. High Cycle Spring: 100,000 cycles.

9.E. Heavy Duty Door: Clopay Model 525V. 9.E.1. Style: Deep ribbed steel doors, insulated. 9.E.2. Interior polyethylene vinyl back cover. 9.E.3. Maximum Door Size: 20 feet 2 inches (6.15 m) wide and 18 feet (5.5 m) high. 9.E.4. Interior pre-painted 30 gauge steel back cover. 9.E.5. Exterior Steel Skin Thickness: Minimum 25 gauge 0.019 inch (0.48 mm). 9.E.6. 08360-45 Windows: None. 9.E.7. Windows: 24 by 6 inches (610 mm by 152 mm) with polypropylene frame to match door color. 9.E.7.a. Glazing: 1/8 inch (3 mm) DSB sheet glass glazing. 9.E.7.b. Glazing: 1/8 inch (3 mm) tempered sheet glass glazing. 9.E.7.c. Glazing: 1/8 inch (3 mm) acrylic glazing. 9.E.7.d. Glazing: 1/8 inch (3 mm) clear polycarbonate glazing. 9.E.8. Windows: 24 by 12 inch (610 by 300 mm) with polypropylene frame to match door color. 9.E.8.a. Glazing: 1/8 inch (3 mm) DSB sheet glass glazing. 9.E.8.b. Glazing: 1/8 inch (3 mm) tempered sheet glass glazing. 9.E.8.c. Glazing: 1/8 inch (3 mm) acrylic glazing. 9.E.8.d. Glazing: 1/8 inch (3 mm) clear polycarbonate glazing. 9.E.9. Windows: Full-view aluminum sections, pre-painted to match door finish. 9.E.9.a. Glazing: 1/8 inch (3 mm) DSB sheet glass glazing. 9.E.9.b. Glazing: 1/8 inch (3 mm) tempered sheet glass glazing. 9.E.9.c. Glazing: 1/8 inch (3 mm) acrylic glazing. 9.E.9.d. Glazing: 1/8 inch (3 mm) clear polycarbonate glazing. 9.E.10. Finish: Exterior 1 mil (.025 mm) coating; interior 0.5 mil (0.013 mm) coating; color as follows: 9.E.10.a. White. 9.E.10.b. Brown. 9.E.11. Locking: No Lock. 9.E.12. Locking: Inside spring loaded slide bolt lock on end stile that engages slot in track. 9.E.12.a. Provide one inside slide lock. 9.E.12.b. Provide two inside slide lock. 9.E.12.c. Provide five pin cylinder lock with outside key. 9.E.13. Door Drop Safety Device: Provide brackets designed to stop the fall of the door should lift cables fail. 9.E.14. Weatherstripping: Provide complete perimeter seals. Provide flexible top seal, flexible jamb seal and U shaped bottom seal. 9.E.15. Track: 9.E.15.a. Vertical Track: 2 inches (50 mm) wide, minimum 0.061 inch (1.55mm) galvanized steel tapered and mounted for wedge type closing. 9.E.15.b. Vertical Track: 3 inches (75 mm) wide, minimum 0.099 inch (2.52 mm) galvanized 08360-46 steel tapered and mounted for wedge type closing. 9.E.15.c. Horizontal Track: 2 inches (50 mm) wide, minimum 0.075 inch (1.91 mm) galvanized steel, reinforced with minimum 0.0897 inch (2.28 mm) galvanized steel angles as required. 9.E.15.d. Horizontal Track: 3 inches (50 mm) wide, minimum 0.099 inch (2.52 mm) galvanized steel, reinforced with minimum 0.0897 inch (2.28 mm) galvanized steel angles as required. 9.E.15.e. Provide standard lift tracks with 15 inches (381 mm) radius track as indicated. 9.E.15.f. Provide vertical lift tracks as indicated. 9.E.15.g. Provide high lift tracks as indicated. 9.E.15.h. Provide tracks that follow roof slope tracks as indicated. 9.E.15.i. Provide low headroom tracks as indicated. 9.E.16. Spring Counterbalance: Torsion spring counterbalance mechanism sized to weight of the door, with a helically wound, oil tempered torsion spring mounted on a steel shaft; cable drum of die cast aluminum with high strength galvanized aircraft cable with minimum 7 to 1 safety factor. 9.E.16.a. Standard Cycle Spring: 10,000 cycle. 9.E.16.b. High Cycle Spring: 25,000 cycles. 9.E.16.c. High Cycle Spring: 50,000 cycles. 9.E.16.d. High Cycle Spring: 100,000 cycles.

9.F. Door Construction: 9.F.1. Panel Sections: 2 inches (52 mm) thick roll formed commercial quality steel panel sections, hot-dip galvanized per ASTM A 924/A 924M and ASTM A 653/A 653M, phosphatized and prepainted with primer and baked-on polyester topcoat. Panel faces reinforced with two 1/2 inch (13 mm) deep ribs on 8 inches (200 mm) centers, complemented by six 1/8 inch (3 mm) beads on 2 inches (50 mm) centers. Sections formed to created weathertight tongue and groove meeting rail. Bottom panel section reinforced with continuous 0.050 inch (1.27 mm) aluminum astragal retainer with U- shaped flexible PVC astragal. 9.F.2. Door Stiles: Galvanized, primed, and polyester top-coated turn-down steel end stiles; wrap face of panel sections a full 1-3/8 inches (35 mm); 0.049 inch (1.25 mm) minimum thickness up to 14 ft-2 inches (4.32 m), otherwise 0.61 inch (1.55 mm) thickness; engineered for easy hardware attachment through pre-punched holes. 9.F.3. Insulation: 1-3/8 inches thick (35 mm) polystyrene insulation with fire retardant additive to meet requirements of UL R-1894A, covered by steel backers on interior for durability; thermal resistance (R-value), 6.6 hr sq ft deg F/BTU (1.2 K sq m/W); calculated door section R-value in accordance with DASMA TDS-163. 9.F.4. Connections: Fasten panel sections and stiles with manufacturer's Tog-L-Loc joining system.

2.10 FLUSH STEEL DOORS, POLYSTYRENE INSULATED

10.A. 08360-47 Premium Duty Door: Clopay Model 522S. 10.A.1. Style: Flush steel doors, polystyrene insulated. 10.A.2. Maximum Door Size: 24 feet, 2 inches (7.37 m) wide and 24 feet (7.32 m) high. 10.A.3. Interior pre-painted 30 gauge steel back cover. 10.A.4. Exterior Steel Skin Thickness: Minimum 20 gauge 0.034 inch (0.86 mm). 10.A.5. Windows: None. 10.A.6. Windows: 24 inches by 6 inches (150 mm by 610 mm) with polypropylene frame to match door color. 10.A.6.a. Glazing: 1/8 inch (3 mm) DSB clear float glass. 10.A.6.b. Glazing: 1/4 inch (6 mm) tempered clear float glass. 10.A.6.c. Glazing: 1/2 inch (13 mm) dual pane insulated glazing. 10.A.7. Windows: 24 inches by 12 inches (610 mm by 300 mm) with polypropylene frame to match door color. 10.A.7.a. Glazing: 1/8 inch (3 mm) DSB clear float glass. 10.A.7.b. Glazing: 1/4 inch (6 mm) tempered clear float glass. 10.A.7.c. Glazing: 1/2 inch (13 mm) dual pane insulated glazing. 10.A.8. Windows: Full-view sections, pre-painted to match door finish. 10.A.8.a. Glazing: 1/8 inch (3 mm) DSB clear float glass. 10.A.8.b. Glazing: 1/4 inch (6 mm) tempered clear float glass. 10.A.8.c. Glazing: 1/2 inch (13 mm) dual pane insulated glazing. 10.A.9. Finish: Exterior 1 mil (.025 mm) coating; interior 0.5 mil (0.013 mm) coating; color as follows: 10.A.9.a. White. 10.A.9.b. Brown. 10.A.10. Locking: No Lock. 10.A.11. Locking: Inside spring loaded slide bolt lock on end stile that engages slot in track. 10.A.11.a. Provide one inside slide lock. 10.A.11.b. Provide two inside slide lock. 10.A.11.c. Provide five pin cylinder lock with outside key. 10.A.12. Door Drop Safety Device: Provide brackets designed to stop the fall of the door should lift cables fail. 10.A.13. Weatherstripping: Provide complete perimeter seals. Provide flexible top seal, flexible jamb seal and U shaped bottom seal. 10.A.14. Track: 08360-48 10.A.14.a. Vertical Track: 2 inches (50 mm) wide, minimum 0.061 inch (1.55mm) galvanized steel tapered and mounted for wedge type closing. 10.A.14.b. Vertical Track: 3 inches (75 mm) wide, minimum 0.099 inch (2.52 mm) galvanized steel tapered and mounted for wedge type closing. 10.A.14.c. Horizontal Track: 2 inches (50 mm) wide, minimum 0.075 inch (1.91 mm) galvanized steel, reinforced with minimum 0.0897 inch (2.28 mm) galvanized steel angles as required. 10.A.14.d. Horizontal Track: 3 inches (50 mm) wide, minimum 0.099 inch (2.52 mm) galvanized steel, reinforced with minimum 0.0897 inch (2.28 mm) galvanized steel angles as required. 10.A.14.e. Provide standard lift tracks with 15 inches (381 mm) radius track as indicated. 10.A.14.f. Provide vertical lift tracks as indicated. 10.A.14.g. Provide high lift tracks as indicated. 10.A.14.h. Provide tracks that follow roof slope tracks as indicated. 10.A.14.i. Provide low headroom tracks as indicated. 10.A.15. Spring Counterbalance: Torsion spring counterbalance mechanism sized to weight of the door, with a helically wound, oil tempered torsion spring mounted on a steel shaft; cable drum of die cast aluminum with high strength galvanized aircraft cable with minimum 7 to 1 safety factor. 10.A.15.a. Standard Cycle Spring: 10,000 cycle. 10.A.15.b. High Cycle Spring: 25,000 cycles. 10.A.15.c. High Cycle Spring: 50,000 cycles. 10.A.15.d. High Cycle Spring: 100,000 cycles. 10.A.16. Break-Away Bottom Section: Integral part of door; with fiberglass or 1/8 inch (3 mm) polycarbonate lined bottom section with flexible neoprene rubber side edges; exterior to match door face. 10.A.16.a. Single breakaway bottom section for doors up to 20 feet (6 m) wide. 10.A.16.b. Double breakaway bottom section for doors up to 14 feet (4.3 m) wide. 10.A.17. Pass Door (Walk-Through Service Door): Integral part of door; 32 inches (813 mm) by 80 inches (2032 mm) with aluminum frame, welded corners, geared hinge, and pneumatic door closer; exterior matching door face; integral shiplap weather seal; keyed dead latch security lock.

10.B. Door Construction: 10.B.1. Panel Sections: 2 inches (52 mm) thick roll formed commercial quality steel panel sections, hot-dip galvanized per ASTM A 924/A 924M and ASTM A 653/A 653M, phosphatized and prepainted with primer and baked-on polyester topcoat. Panel faces reinforced with two 1/2 inch (13 mm) deep ribs on 8 inches (200 mm) centers, complemented by six 1/8 inch (3 mm) beads on 2 inches (50 mm) centers. Sections formed to created weathertight tongue and groove meeting rail. Bottom panel section reinforced with continuous 0.050 inch (1.27 mm) aluminum astragal retainer with U- shaped flexible PVC astragal. 08360-49 10.B.2. Door Stiles: Galvanized, primed, and polyester top-coated turn-down steel end stiles; wrap face of panel sections a full 1-3/8 inches (35 mm); 0.049 inch (1.25 mm) minimum thickness up to 14 ft-2 inches (4.32 m), otherwise 0.61 inch (1.55 mm) thickness; engineered for easy hardware attachment through pre-punched holes. 10.B.3. Insulation: 1-3/8 inches thick (35 mm) polystyrene insulation with fire retardant additive to meet requirements of UL R-1894A, covered by steel backers on interior for durability; thermal resistance (R-value), 6.83 hr sq ft deg F/BTU (1.2 K sq m/W); calculated door section R-value in accordance with DASMA TDS-163. 10.B.4. Connections: Fasten panel sections and stiles with manufacturer's Tog-L-Loc joining system.

2.11 RAISED PANEL STEEL DOORS, POLYSTYRENE INSULATED

11.A. Heavy Duty Door: Clopay Model 664V. 11.A.1. Style: Steel woodgrain embossed raised panel steel door (Polystyrene insulation with vinyl back cover). 11.A.2. Maximum Door Size: 20 feet (6.10 m) wide by 18 feet (5.49 m) high. 11.A.3. Overall Panel Thickness: 2 inches (51 mm). 11.A.4. Exterior Skin Thickness: Minimum 24 gauge 0.022 inch (0.56 mm) exterior. 11.A.5. Interior Skin: Polyethylene vinyl backer. Color: white. 11.A.6. Stiles: Steel prepainted end stiles, minimum 18 gauge (0.049 inch) (1.25 mm) thick, up to 16 feet - 2 inches (4.9 m) wide. Over 16 feet - 2 inches (4.9 m) provide double end stile composed of one 18 gauge (.049 inch) (1.25 mm) minimum plus one 20 gauge (.035 inch) (.89 mm) minimum center stile. 11.A.7. Thermal Resistance (R-value): 6.3 deg F hr sq ft/Btu (1.1 (K sq m)/W); calculated door section R-value in accordance with DASMA TDS-163. 11.A.8. Windows: None. 11.A.9. Window: PVC windows measuring 12 inches by 19-1/2 inches (305 mm by 495 mm): 11.A.9.a. Glazing: 1/8 inch (3 mm) DSB sheet glass. 11.A.9.b. Glazing: 1/8 inch (3 mm) clear acrylic sheet. 11.A.9.c. Glazing: 1/8 inch (3 mm) obscure sheet glass. 11.A.10. Finish: Raised panel wood grain exterior design, pre-finished exterior with 1-mil, three coat baked-on polyester topcoat over primer on a phosphate coating. as follows: 11.A.10.a. White. 11.A.10.b. Brown 11.A.10.c. Almond. 11.A.10.d. Desert Tan. 11.A.10.e. Sandtone. 11.A.11. 08360-50 Locking: No Lock. 11.A.12. Locking: Inside spring loaded slide bolt lock on end stile that engages slot in track. 11.A.12.a. Provide a five point cylinder lock with L-handle and a single lock bar. 11.A.13. Door Drop Safety Device: Provide brackets designed to stop the fall of the door should lift cables fail. 11.A.14. Weatherstripping: Section joint seal tape shall be Neoprene foam seal, one-piece full length between joint of sections. Field installed jamb/header weather-stripping shall be extruded vinyl, placed in contact with outside of door sections. Astragal shall be full length of section, .040 inch (1.02 mm) aluminum retainer with U-shaped flexible PVC vinyl. 11.A.15. Hinge and Roller Assemblies: Hinges and brackets shall be 14 gauge (.070 inch), (1.78 mm) minimum galvanized steel. Ten-ball bearing steel rollers to be full-floating ball bearing in case hardened steel races and mounted to fit the taper of the track. 11.A.16. Tracks: Vertical tracks minimum 16 gauge (0.061 inch) (1.55 mm) galvanized steel tapered and mounted for wedge type closing. Horizontal tracks minimum 14 gauge (0.075 inch) (1.91 mm) galvanized steel, reinforced with minimum 13 gauge (0.0897 inch) (2.28 mm) galvanized steel angles as required: 11.A.16.a. Track Width: 2 inches (50 mm). 11.A.16.b. Track Width: 3 inches (75 mm). 11.A.16.c. Provide standard lift tracks with 15 inches (381 mm) radius track as indicated. 11.A.16.d. Provide vertical lift tracks as indicated. 11.A.16.e. Provide high lift tracks as indicated. 11.A.16.f. Provide tracks that follow roof slope tracks as indicated. 11.A.16.g. Provide low headroom tracks as indicated. 11.A.17. Track Mounting: (Bracket Mounting) Galvanized steel mounting brackets 12 gauge (.101 inch), (2.57 mm) minimum thick for wood jambs. 11.A.18. Track Mounting: (Continuous or Reverse Galvanized Steel Angle Mounting) 12 gauge (.101 inch), (2.57 mm) minimum angle for steel jambs; splice plates 12 gauge (.101 inch), (2.57 mm) minimum. 11.A.19. Spring Counterbalance: Torsion type, low stress, helically wound, oil-tempered spring on a galvanized steel tube or solid steel shaft. Die cast aluminum. Pre-formed galvanized steel aircraft cable to provide a minimum of a 7:1 safety factor. 11.A.19.a. Standard Cycle Spring: 10,000 cycle. 11.A.19.b. High Cycle Spring: 25,000 cycles. 11.A.19.c. High Cycle Spring: 50,000 cycles. 11.A.19.d. High Cycle Spring: 100,000 cycles.

11.B. Door Construction: 11.B.1. Panels: Steel woodgrain embossed raised panel steel door (Polystyrene insulation with vinyl back cover). 08360-51 11.B.2. Steel Skin: Formed from roll formed commercial or drawing quality steel sheet, hot-dip galvanized per ASTM A 924/A 924M and ASTM A 653/A 653M, pre-painted with primer and baked-on polyester topcoat. 11.B.3. Section Joint: Sections to form a weather-tight tongue and groove joint. 11.B.4. Reinforcing: Galvanized and primed steel reinforcement located under each hinge location, pre-punched for hinge attachment. 11.B.5. Handle: 3 inches (76 mm) horizontal galvanized steel step plate / lift handle shall be located on bottom section.

2.12 DEEP RIBBED STEEL DOORS, NON-INSULATED

12.A. Premium Duty Door: Clopay Model 520. 12.A.1. Style: Deep ribbed steel doors, non-insulated. 12.A.2. Maximum Door Size: 32 feet, 2 inches (9.8 m) wide by 26 feet (7.9 m) high. 12.A.3. Steel Skin Thickness: Minimum 20 gauge 0.034 inch (0.86 mm). 12.A.4. Windows: None. 12.A.5. Windows: 24 inches by 6 inches (150 mm by 610 mm) with polypropylene frame to match door color. 12.A.5.a. Glazing: 1/8 inch (3 mm, DSB clear float glass. 12.A.5.b. Glazing: 1/4 inch (6 mm) tempered clear float glass. 12.A.6. Windows: 24 inches by 12 inches (610 mm by 300 mm) with polypropylene frame to match door color. 12.A.6.a. Glazing: 1/8 inch (3 mm, DSB clear float glass. 12.A.6.b. Glazing: 1/4 inch (6 mm) tempered clear float glass. 12.A.7. Windows: Full-view sections, pre-painted to match door finish. 12.A.7.a. Glazing: 1/8 inch (3 mm) DSB clear float glass. 12.A.7.b. Glazing: 1/4 inch (6 mm) tempered clear float glass. 12.A.8. Finish: Exterior 1 mil (.025 mm) coating; interior 0.5 mil (0.013 mm) coating; color as follows: 12.A.8.a. White. 12.A.8.b. Brown. 12.A.9. Locking: No Lock. 12.A.10. Locking: Inside spring loaded slide bolt lock on end stile that engages slot in track. 12.A.10.a. Provide one inside slide lock. 12.A.10.b. Provide two inside slide lock. 12.A.10.c. 08360-52 Provide five pin cylinder lock with outside key. 12.A.11. Door Drop Safety Device: Provide brackets designed to stop the fall of the door should lift cables fail. 12.A.12. Weatherstripping: Provide complete perimeter seals. Provide flexible top seal, flexible jamb seal and U shaped bottom seal. 12.A.13. Track: 12.A.13.a. Vertical Track: 2 inches (50 mm) wide, minimum 0.061 inch (1.55mm) galvanized steel tapered and mounted for wedge type closing. 12.A.13.b. Vertical Track: 3 inches (75 mm) wide, minimum 0.099 inch (2.52 mm) galvanized steel tapered and mounted for wedge type closing. 12.A.13.c. Horizontal Track: 2 inches (50 mm) wide, minimum 0.075 inch (1.91 mm) galvanized steel, reinforced with minimum 0.0897 inch (2.28 mm) galvanized steel angles as required. 12.A.13.d. Horizontal Track: 3 inches (50 mm) wide, minimum 0.099 inch (2.52 mm) galvanized steel, reinforced with minimum 0.0897 inch (2.28 mm) galvanized steel angles as required. 12.A.13.e. Provide standard lift tracks with 15 inches (381 mm) radius track as indicated. 12.A.13.f. Provide vertical lift tracks as indicated. 12.A.13.g. Provide high lift tracks as indicated. 12.A.13.h. Provide tracks that follow roof slope tracks as indicated. 12.A.13.i. Provide low headroom tracks as indicated. 12.A.14. Spring Counterbalance: Torsion spring counterbalance mechanism sized to weight of the door, with a helically wound, oil tempered torsion spring mounted on a steel shaft; cable drum of die cast aluminum with high strength galvanized aircraft cable with minimum 7 to 1 safety factor. 12.A.14.a. Standard Cycle Spring: 10,000 cycle. 12.A.14.b. High Cycle Spring: 25,000 cycles. 12.A.14.c. High Cycle Spring: 50,000 cycles. 12.A.14.d. High Cycle Spring: 100,000 cycles. 12.A.15. Break-Away Bottom Section: Integral part of door; with fiberglass or 1/8 inch (3 mm) polycarbonate lined bottom section with flexible neoprene rubber side edges; exterior to match door face. 12.A.15.a. Single breakaway bottom section for doors up to 20 feet (6 m) wide. 12.A.15.b. Double breakaway bottom section for doors up to 14 feet (4.3 m) wide. 12.A.16. Pass Door (Walk-Through Service Door): Integral part of door; 32 inches (813 mm) by 80 inches (2032 mm) with aluminum frame, welded corners, geared hinge, and pneumatic door closer; exterior matching door face; integral shiplap weather seal; keyed dead latch security lock.

12.B. Heavy Duty Door: Clopay Model 524. 08360-53 12.B.1. Style: Deep ribbed steel doors, non-insulated. 12.B.2. Maximum Door Size: 26 feet, 2 inches (7.97 m) wide by 24 feet (7.31 m) high. 12.B.3. Steel Skin Thickness: Minimum 24 gauge 0.022 inch (0.56 mm). 12.B.4. Windows: None. 12.B.5. Windows: 24 inches by 6 inches (150 mm by 610 mm) with polypropylene frame to match door color. 12.B.5.a. Glazing: 1/8 inch (3 mm) DSB clear float glass. 12.B.5.b. Glazing: 1/4 inch (6 mm) tempered clear float glass. 12.B.6. Windows: 24 inches by 12 inches (610 mm by 300 mm) with polypropylene frame to match door color. 12.B.6.a. Glazing: 1/8 inch (3 mm) DSB clear float glass. 12.B.6.b. Glazing: 1/4 inch (6 mm) tempered clear float glass. 12.B.7. Windows: Full-view sections, pre-painted to match door finish. 12.B.7.a. Glazing: 1/8 inch (3 mm) DSB clear float glass. 12.B.7.b. Glazing: 1/4 inch (6 mm) tempered clear float glass. 12.B.8. Finish: Exterior 1 mil (.025 mm) coating; interior 0.5 mil (0.013 mm) coating; color as follows: 12.B.8.a. White. 12.B.8.b. Brown. 12.B.8.c. Commercial Tan. 12.B.8.d. Gray. 12.B.8.e. Trinar White. 12.B.9. Locking: No Lock. 12.B.10. Locking: Inside spring loaded slide bolt lock on end stile that engages slot in track. 12.B.10.a. Provide one inside slide lock. 12.B.10.b. Provide two inside slide lock. 12.B.10.c. Provide five pin cylinder lock with outside key. 12.B.11. Door Drop Safety Device: Provide brackets designed to stop the fall of the door should lift cables fail . 12.B.12. Weatherstripping: Provide complete perimeter seals. Provide flexible top seal, flexible jamb seal and U shaped bottom seal. 12.B.13. Track: 12.B.13.a. Vertical Track: 2 inches (50 mm) wide, minimum 0.061 inch (1.55mm) galvanized steel tapered and mounted for wedge type closing. 08360-54 12.B.13.b. Vertical Track: 3 inches (75 mm) wide, minimum 0.099 inch (2.52 mm) galvanized steel tapered and mounted for wedge type closing. 12.B.13.c. Horizontal Track: 2 inches (50 mm) wide, minimum 0.075 inch (1.91 mm) galvanized steel, reinforced with minimum 0.0897 inch (2.28 mm) galvanized steel angles as required. 12.B.13.d. Horizontal Track: 3 inches (50 mm) wide, minimum 0.099 inch (2.52 mm) galvanized steel, reinforced with minimum 0.0897 inch (2.28 mm) galvanized steel angles as required. 12.B.13.e. Provide standard lift tracks with 15 inches (381 mm) radius track as indicated. 12.B.13.f. Provide vertical lift tracks as indicated. 12.B.13.g. Provide high lift tracks as indicated. 12.B.13.h. Provide tracks that follow roof slope tracks as indicated. 12.B.13.i. Provide low headroom tracks as indicated. 12.B.14. Spring Counterbalance: Torsion spring counterbalance mechanism sized to weight of the door, with a helically wound, oil tempered torsion spring mounted on a steel shaft; cable drum of die cast aluminum with high strength galvanized aircraft cable with minimum 7 to 1 safety factor. 12.B.14.a. Standard Cycle Spring: 10,000 cycle. 12.B.14.b. High Cycle Spring: 25,000 cycles. 12.B.14.c. High Cycle Spring: 50,000 cycles. 12.B.14.d. High Cycle Spring: 100,000 cycles. 12.B.15. Break-Away Bottom Section: Integral part of door; with fiberglass or 1/8 inch (3 mm) polycarbonate lined bottom section with flexible neoprene rubber side edges; exterior to match door face. 12.B.15.a. Single breakaway bottom section for doors up to 20 feet (6 m) wide. 12.B.15.b. Double breakaway bottom section for doors up to 14 feet (4.3 m) wide. 12.B.16. Pass Door (Walk-Through Service Door): Integral part of door; 32 inches (813 mm) by 80 inches (2032 mm) with aluminum frame, welded corners, geared hinge, and pneumatic door closer; exterior matching door face; integral shiplap weather seal; keyed dead latch security lock.

12.C. Standard Duty Door: Clopay Model 525. 12.C.1. Style: Deep ribbed steel doors, non-insulated. 12.C.2. Maximum Door Size: 20 feet 2 inches (6.15 m) wide by 18 feet (5.5 m) high. 12.C.3. Steel Skin Thickness: Minimum 25 gauge 0.019 inch (0.48 mm). 12.C.4. Windows: None. 12.C.5. Windows: 24 by 6 inches (610 mm by 152 mm) with polypropylene frame to match door color. 12.C.5.a. 08360-55 Glazing: 1/8 inch (3 mm) DSB sheet glass glazing. 12.C.5.b. Glazing: 1/8 inch (3 mm) tempered sheet glass glazing. 12.C.5.c. Glazing: 1/8 inch (3 mm) acrylic glazing. 12.C.5.d. Glazing: 1/8 inch (3 mm) clear polycarbonate glazing. 12.C.6. Windows: 24 by 12 inch (610 by 300 mm) with polypropylene frame to match door color. 12.C.6.a. Glazing: 1/8 inch (3 mm) DSB sheet glass glazing. 12.C.6.b. Glazing: 1/8 inch (3 mm) tempered sheet glass glazing. 12.C.6.c. Glazing: 1/8 inch (3 mm) acrylic glazing. 12.C.6.d. Glazing: 1/8 inch (3 mm) clear polycarbonate glazing. 12.C.7. Windows: Full-view aluminum sections, pre-painted to match door finish. 12.C.7.a. Glazing: 1/8 inch (3 mm) DSB sheet glass glazing. 12.C.7.b. Glazing: 1/8 inch (3 mm) tempered sheet glass glazing. 12.C.7.c. Glazing: 1/8 inch (3 mm) acrylic glazing. 12.C.7.d. Glazing: 1/8 inch (3 mm) clear polycarbonate glazing. 12.C.8. Finish: Exterior 1 mil (.025 mm) coating; interior 0.5 mil (0.013 mm) coating; color as follows: 12.C.8.a. White. 12.C.8.b. Brown. 12.C.9. Locking: No Lock. 12.C.10. Locking: Inside spring loaded slide bolt lock on end stile that engages slot in track. 12.C.10.a. Provide one inside slide lock. 12.C.10.b. Provide two inside slide lock. 12.C.10.c. Provide five pin cylinder lock with outside key. 12.C.11. Door Drop Safety Device: Provide brackets designed to stop the fall of the door should lift cables fail . 12.C.12. Weatherstripping: Provide complete perimeter seals. Provide flexible top seal, flexible jamb seal and U shaped bottom seal. 12.C.13. Track: 12.C.13.a. Vertical Track: 2 inches (50 mm) wide, minimum 0.061 inch (1.55mm) galvanized steel tapered and mounted for wedge type closing. 12.C.13.b. Vertical Track: 3 inches (75 mm) wide, minimum 0.099 inch (2.52 mm) galvanized steel tapered and mounted for wedge type closing. 12.C.13.c. Horizontal Track: 2 inches (50 mm) wide, minimum 0.075 inch (1.91 mm) galvanized steel, reinforced with minimum 0.0897 inch (2.28 mm) galvanized steel angles as required. 08360-56 12.C.13.d. Horizontal Track: 3 inches (50 mm) wide, minimum 0.099 inch (2.52 mm) galvanized steel, reinforced with minimum 0.0897 inch (2.28 mm) galvanized steel angles as required. 12.C.13.e. Provide standard lift tracks with 15 inches (381 mm) radius track as indicated. 12.C.13.f. Provide vertical lift tracks as indicated. 12.C.13.g. Provide high lift tracks as indicated. 12.C.13.h. Provide tracks that follow roof slope tracks as indicated. 12.C.13.i. Provide low headroom tracks as indicated. 12.C.14. Spring Counterbalance: Torsion spring counterbalance mechanism sized to weight of the door, with a helically wound, oil tempered torsion spring mounted on a steel shaft; cable drum of die cast aluminum with high strength galvanized aircraft cable with minimum 7 to 1 safety factor. 12.C.14.a. Standard Cycle Spring: 10,000 cycle. 12.C.14.b. High Cycle Spring: 25,000 cycles. 12.C.14.c. High Cycle Spring: 50,000 cycles. 12.C.14.d. High Cycle Spring: 100,000 cycles.

12.D. Door Construction: 12.D.1. Panel Sections: 2 inches (52 mm) thick roll formed commercial quality steel panel sections, hot-dip galvanized per ASTM A 924/A 924M and ASTM A 653/A 653M, phosphatized and prepainted with primer and baked-on polyester topcoat. Panel faces reinforced with two 1/2 inch (13 mm) deep ribs on 8 inches (200 mm) centers, complemented by six 1/8 inch (3 mm) beads on 2 inches (50 mm) centers. Sections formed to create a weathertight tongue and groove meeting rail. Bottom panel section reinforced with continuous 0.050 inch (1.27 mm) aluminum astragal retainer with U- shaped flexible PVC astragal. 12.D.2. Door Stiles: Galvanized, primed, and polyester top-coated turn-down steel end stiles; wrap face of panel sections a full 1-3/8 inches (35 mm); 0.049 inch (1.25 mm) minimum thickness up to 14 ft, 2 inches (4.32 m), otherwise 0.61 inch (1.55 mm) thickness; engineered for easy hardware attachment through pre-punched holes. 12.D.3. Connections: Fasten panel sections and stiles with manufacturer's Tog-L-Loc joining system.

2.13 FLUSH STEEL DOORS, NON-INSULATED

13.A. Premium Duty Door: Clopay Model 522. 13.A.1. Style: Flush steel doors, non-insulated. 13.A.2. Maximum Door Size: 24 feet, 2 inches (7.37 m) wide by 24 feet (7.32 m) high. 13.A.3. Steel Skin Thickness: Minimum 20 gauge 0.034 inch (0.86 mm). 13.A.4. Windows: None. 13.A.5. 08360-57 Windows: 24 inches by 6 inches (150 mm by 610 mm) with polypropylene frame to match door color. 13.A.5.a. Glazing: 1/8 inch (3 mm) DSB clear float glass. 13.A.5.b. Glazing: 1/4 inch (6 mm) tempered clear float glass. 13.A.6. Windows: 24 inches by 12 inches (610 mm by 300 mm) with polypropylene frame to match door color. 13.A.6.a. Glazing: 1/8 inch (3 mm) DSB clear float glass. 13.A.6.b. Glazing: 1/4 inch (6 mm) tempered clear float glass. 13.A.7. Windows: Full-view sections, pre-painted to match door finish. 13.A.7.a. Glazing: 1/8 inch (3 mm) DSB clear float glass. 13.A.7.b. Glazing: 1/4 inch (6 mm) tempered clear float glass. 13.A.7.c. Glazing: 1/2 inch (13 mm) dual pane insulated glazing. 13.A.8. Finish: Exterior 1 mil (.025 mm) coating; interior 0.5 mil (0.013 mm) coating; color as follows: 13.A.8.a. White. 13.A.8.b. Brown. 13.A.9. Locking: No Lock. 13.A.10. Locking: Inside spring loaded slide bolt lock on end stile that engages slot in track. 13.A.10.a. Provide one inside slide lock. 13.A.10.b. Provide two inside slide lock. 13.A.10.c. Provide five pin cylinder lock with outside key. 13.A.11. Door Drop Safety Device: Provide brackets designed to stop the fall of the door should lift cables fail . 13.A.12. Weatherstripping: Provide complete perimeter seals. Provide flexible top seal, flexible jamb seal and U shaped bottom seal. 13.A.13. Track: 13.A.13.a. Vertical Track: 2 inches (50 mm) wide, minimum 0.061 inch (1.55mm) galvanized steel tapered and mounted for wedge type closing. 13.A.13.b. Vertical Track: 3 inches (75 mm) wide, minimum 0.099 inch (2.52 mm) galvanized steel tapered and mounted for wedge type closing. 13.A.13.c. Horizontal Track: 2 inches (50 mm) wide, minimum 0.075 inch (1.91 mm) galvanized steel, reinforced with minimum 0.0897 inch (2.28 mm) galvanized steel angles as required. 13.A.13.d. Horizontal Track: 3 inches (50 mm) wide, minimum 0.099 inch (2.52 mm) galvanized steel, reinforced with minimum 0.0897 inch (2.28 mm) galvanized steel angles as required. 13.A.13.e. Provide standard lift tracks with 15 inches (381 mm) radius track as indicated. 08360-58 13.A.13.f. Provide vertical lift tracks as indicated. 13.A.13.g. Provide high lift tracks as indicated. 13.A.13.h. Provide tracks that follow roof slope tracks as indicated. 13.A.13.i. Provide low headroom tracks as indicated. 13.A.14. Spring Counterbalance: Torsion spring counterbalance mechanism sized to weight of the door, with a helically wound, oil tempered torsion spring mounted on a steel shaft; cable drum of die cast aluminum with high strength galvanized aircraft cable with minimum 7 to 1 safety factor. 13.A.14.a. Standard Cycle Spring: 10,000 cycle. 13.A.14.b. High Cycle Spring: 25,000 cycles. 13.A.14.c. High Cycle Spring: 50,000 cycles. 13.A.14.d. High Cycle Spring: 100,000 cycles. 13.A.15. Break-Away Bottom Section: Integral part of door; with fiberglass or 1/8 inch (3 mm) polycarbonate lined bottom section with flexible neoprene rubber side edges; exterior to match door face. 13.A.15.a. Single breakaway bottom section for doors up to 20 feet (6 m) wide. 13.A.15.b. Double breakaway bottom section for doors up to 14 feet (4.3 m) wide. 13.A.16. Pass Door (Walk-Through Service Door): Integral part of door; 32 inches (813 mm) by 80 inches (2032 mm) with aluminum frame, welded corners, geared hinge, and pneumatic door closer; exterior matching door face; integral shiplap weather seal; keyed dead latch security lock.

13.B. Door Construction: 13.B.1. Panel Sections: 2 inches (52 mm) thick roll formed commercial quality steel panel sections, hot-dip galvanized per ASTM A 924/A 924M and ASTM A 653/A 653M, phosphatized and prepainted with primer and baked-on polyester topcoat. Panel faces reinforced with two 1/2 inch (13 mm) deep ribs on 8 inches (200 mm) centers, complemented by six 1/8 inch (3 mm) beads on 2 inches (50 mm) centers. Sections formed to create a weathertight tongue and groove meeting rail. Bottom panel section reinforced with continuous 0.050 inch (1.27 mm) aluminum astragal retainer with U- shaped flexible PVC astragal. 13.B.2. Door Stiles: Galvanized, primed, and polyester top-coated turn-down steel end stiles; wrap face of panel sections a full 1-3/8 inches (35 mm); 0.049 inch (1.25 mm) minimum thickness up to 14 ft, 2 inches (4.32 m), otherwise 0.61 inch (1.55 mm) thickness; engineered for easy hardware attachment through pre-punched holes. 13.B.3. Connections: Fasten panel sections and stiles with manufacturer's Tog-L-Loc joining system.

2.14 RAISED PANEL STEEL DOORS, NON-INSULATED

14.A. Heavy Duty Door: Clopay Model 664. 14.A.1. Style: Raised panel steel doors, non-insulated. 08360-59 14.A.2. Maximum Door Size: 20 feet (6.10 m) wide by 18 feet (5.49 m) high. 14.A.3. Exterior Skin Thickness: Minimum 24 gauge 0.022 inch (0.56 mm) exterior. 14.A.4. Interior Finish of Exterior Skin: White. 14.A.5. Stiles: Steel prepainted end stiles, minimum 18 gauge (0.049 inch) (1.25 mm) thick, up to 16 feet - 2 inches (4.9 m) wide. Over 16 feet - 2 inches (4.9 m) provide double end stile composed of one 18 gauge (.049 inch) (1.25 mm) minimum plus one 20 gauge (.035 inch) (.89 mm) minimum center stile. 14.A.6. Windows: None. 14.A.7. Window: PVC windows measuring 12 inches by 19-1/2 inches (305 mm by 495 mm): 14.A.7.a. Glazing: 1/8 inch (3 mm) DSB sheet glass. 14.A.7.b. Glazing: 1/8 inch (3 mm) clear acrylic sheet. 14.A.7.c. Glazing: 1/8 inch (3 mm) obscure sheet glass. 14.A.8. Finish: Raised panel wood grain exterior design, pre-finished exterior with 1-mil, three coat baked-on polyester topcoat over primer on a phosphate coating. as follows: 14.A.8.a. White. 14.A.8.b. Almond. 14.A.8.c. Desert Tan. 14.A.8.d. Sandtone. 14.A.8.e. Brown. 14.A.9. Locking: No Lock. 14.A.10. Locking: Inside spring loaded slide bolt lock on end stile that engages slot in track. 14.A.10.a. Provide a four point cylinder lock with L-handle and a single lock bar. 14.A.11. Door Drop Safety Device: Provide brackets designed to stop the fall of the door should lift cables fail. 14.A.12. Weatherstripping: Section joint seal tape shall be Neoprene foam seal, one-piece full length between joint of sections. Field installed jamb/header weather-stripping shall be extruded vinyl, placed in contact with outside of door sections. Astragal shall be full length of section, .040 inch (1.02 mm) aluminum retainer with U-shaped flexible PVC vinyl. 14.A.13. Hinge and Roller Assemblies: Hinges and brackets shall be 14 gauge (.070 inch), (1.78 mm) minimum galvanized steel. Ten-ball bearing steel rollers to be full-floating ball bearing in case hardened steel races and mounted to fit the taper of the track. 14.A.14. Tracks: Vertical tracks minimum 16 gauge (0.061 inch) (1.55 mm) (2" track), or min 13 gauge (.099 inch) (2.52mm) (3" track)galvanized steel tapered and mounted for wedge type closing. Horizontal tracks minimum 14 gauge (0.075 inch) (1.91 mm) (2" track) or min. 13 ga. (.099inch) 2.52mm) (3" track) galvanized steel, reinforced with minimum 13 gauge (0.0897 inch) (2.28 mm) galvanized steel angles as required: 14.A.14.a. Track Width: 2 inches (50 mm). 14.A.14.b. 08360-60 Track Width: 3 inches (75 mm). 14.A.14.c. Provide standard lift tracks with 15 inches (381 mm) radius track as indicated. 14.A.14.d. Provide vertical lift tracks as indicated. 14.A.14.e. Provide high lift tracks as indicated. 14.A.14.f. Provide tracks that follow roof slope tracks as indicated. 14.A.14.g. Provide low headroom tracks as indicated. 14.A.15. Track Mounting: (Bracket Mounting) Galvanized steel mounting brackets 12 gauge (.101 inch), (2.57 mm) minimum thick for wood jambs. 14.A.16. Track Mounting: (Continuous or Reverse Galvanized Steel Angle Mounting) 12 gauge (.101 inch), (2.57 mm) minimum angle for steel jambs; splice plates 12 gauge (.101 inch), (2.57 mm) minimum. 14.A.17. Spring Counterbalance: Torsion type, low stress, helically wound, oil-tempered spring on a galvanized steel tube or solid steel shaft. Die cast aluminum. Pre-formed galvanized steel aircraft cable to provide a minimum of a 7:1 safety factor. 14.A.17.a. Standard Cycle Spring: 10,000 cycle. 14.A.17.b. High Cycle Spring: 25,000 cycles. 14.A.17.c. High Cycle Spring: 50,000 cycles. 14.A.17.d. High Cycle Spring: 100,000 cycles.

14.B. Door Construction: 14.B.1. Panels: Steel embossed woodgrain raised panel steel door. 14.B.2. Steel Skin: Formed from roll formed commercial or drawing quality steel sheet, hot-dip galvanized per ASTM A 924/A 924M and ASTM A 653/A 653M, pre-painted with primer and baked-on polyester topcoat. 14.B.3. Section Joint: Sections to form a weather-tight tongue and groove joint. 14.B.4. Reinforcing: Galvanized and primed steel reinforcement located under each hinge location, pre-punched for hinge attachment. 14.B.5. Handle: 3 inches (76 mm) horizontal galvanized steel step plate / lift handle shall be located on bottom section.

2.15 SPECIALTY ALUMINUM DOORS

15.A. Chain Link Security Door: Clopay Model 811. 15.A.1. 0.120 inch (3.0 mm) diameter wire chain link fabric with 2 inch (51 mm) diamond pattern: 2-1/2 inches by 1-1/2 inches (64 mm by 38 mm) aluminum tubular frame internally reinforced corners with 10 gauge galvanized steel plate. 16 ga 1/2 inch (1.5 mm by 12 mm) diamond expanded metal security screen welded to frame. Door size to match exterior door. 15.A.2. Finish: Mill finish aluminum. 15.A.3. 08360-61 Finish: Powdercoat in color as indicated. 15.A.4. Tracks: Vertical tracks minimum 0.061 inch (1.55mm) for 2" track or .099 inch (2.52mm) for 3 " track galvanized steel tapered and mounted for wedge type closing. Horizontal tracks minimum 0.075 inch (1.91 mm) for 2" track or .099 inch (2.52mm) for 3 " track galvanized steel, reinforced with minimum 0.0897 inch (2.28 mm) galvanized steel angles as required: 15.A.4.a. Track Width: 2 inches (50 mm). 15.A.4.b. Track Width: 3 inches (75 mm). 15.A.5. Track Style: 15.A.5.a. Provide with tandem dual track to match exterior door configuration 15.A.5.b. Provide with diverter switch track to match exterior door configuration 15.A.5.c. Provide vertical lift tracks as indicated. 15.A.5.d. Provide high lift tracks as indicated. 15.A.5.e. Provide tracks that follow roof slope tracks as indicated. 15.A.6. Spring Counterbalance: Torsion spring counterbalance mechanism sized to weight of the door, with a helically wound, oil tempered torsion spring mounted on a steel shaft; cable drum of die cast aluminum with high strength galvanized aircraft cable with minimum 7 to 1 safety factor. 15.A.6.a. Standard Cycle Spring: 15,000 cycle. 15.A.6.b. High Cycle Spring: 25,000 cycles. 15.A.6.c. High Cycle Spring: 50,000 cycles. 15.A.6.d. High Cycle Spring: 100,000 cycles.

15.B. Screen Door: Clopay Model 812. 15.B.1. 1-1/2 inches (38 mm) or 1-7/8 inches (48 mm) thick aluminum screen door frame. Frame miter cut and riveted. Screen secured using vinyl snap in bead. Door size to match exterior door. 15.B.2. Screen type: 15.B.2.a. 304 alloy Stainless Steel 3030 mesh. 15.B.2.b. 304 alloy Stainless Steel 1212 mesh. 15.B.3. Finish: Mill finish aluminum. 15.B.4. Finish: Powder coat in color as indicated. 15.B.5. Tracks: Vertical tracks minimum 0.061 inch (1.55mm) for 2" track or .099 inch (2.52mm) for 3 " track galvanized steel tapered and mounted for wedge type closing. Horizontal tracks minimum 0.075 inch (1.91 mm) for 2" track or .099 inch (2.52mm) for 3 " track galvanized steel, reinforced with minimum 0.0897 inch (2.28 mm) galvanized steel angles as required: 15.B.5.a. Track Width: 2 inches (50 mm). 15.B.5.b. 08360-62 Track Width: 3 inches (75 mm). 15.B.6. Track Style: 15.B.6.a. Provide with tandem dual track to match exterior door configuration 15.B.6.b. Provide with diverter switch track to match exterior door configuration 15.B.6.c. Provide vertical lift tracks as indicated. 15.B.6.d. Provide high lift tracks as indicated. 15.B.6.e. Provide tracks that follow roof slope tracks as indicated. 15.B.7. Spring Counterbalance: Torsion spring counterbalance mechanism sized to weight of the door, with a helically wound, oil tempered torsion spring mounted on a steel shaft; cable drum of die cast aluminum with high strength galvanized aircraft cable with minimum 7 to 1 safety factor. 15.B.7.a. Standard Cycle Spring: 15,000 cycle. 15.B.7.b. High Cycle Spring: 25,000 cycles. 15.B.7.c. High Cycle Spring: 50,000 cycles. 15.B.7.d. High Cycle Spring: 100,000 cycles.

2.16 ELECTRIC DOOR OPERATORS

16.A. General: Provide electric door operator provided by door manufacturer for door with operational life specified complete with electric motor and factory pre-wired motor controls, starter, gear- reduction unit, clutch, remote-control stations, control devices, integral gearing for locking door, and accessories required for proper operation. Comply with NFPA 70. 16.A.1. Solenoid-operated brake.

16.B. Disconnect Device:Provide hand-operated disconnect or mechanism for emergency manual operation while disconnecting motor, without affecting timing of limit switch. Mount disconnect and operator so they are accessible from floor level. Include interlock device to automatically prevent motor from operating when emergency operator is engaged.

16.C. Design operator so motor may be removed without disturbing limit switch adjustment and without affecting emergency auxiliary operator.

16.D. Provide control equipment complying with NEMA ICS1, NEMA ICS 2, and NEMA ICS 6, with NFPA 70 Class 2 control circuit, maximum 24-V, AC or DC.

16.E. Electric Motors: Provide high-starting torque, reversible, continuous-duty, Class A insulated, electric motor, complying with NEMA MG 1, with overload protection, sized to start, accelerate, and operate door in either direction, from any position, at not less than 2/3 fps (0.2 m/s) and not more than 1 fps (.03m/s), without exceeding nameplate ratings or considering service factor. 16.E.1. Type: Mechanical. 16.E.2. Type: Solid State. 16.E.3.

08360-63 Type: Jackshaft. 16.E.4. Type: Trolley. 16.E.5. HP: 16.E.5.a. 1/3 hp (246 W). 16.E.5.b. 1/2 hp (373 W). 16.E.5.c. 3/4hp (559 W). 16.E.5.d. 1 hp (746 W). 16.E.6. Power Characteristics: 16.E.6.a. 115 V. 16.E.6.b. 220 V. 16.E.6.c. 460 V. 16.E.6.d. 1 phase. 16.E.6.e. 3 phase. 16.E.7. Service Factor: 16.E.7.a. NEMA MG 1. 16.E.7.b. NEMA 4 watertight. 16.E.7.c. NEMA 9 waterproof. 16.E.7.d. NEMA 10 oil resistant. 16.E.7.e. NEMA 12 explosion resistant. 16.E.8. Coordinate wiring requirements and electrical characteristics of motors with building electrical system.

16.F. Remote Control Station: Provide momentary contact, 3-button control station with push - button controls labeled "Open", "Close" and "Stop".

16.G. Remote Control Station: Provide continuous contact, 3-button control station with push - button controls labeled "Open", "Close" and "Stop".

16.H. Provide interior units, fully guarded, surface mounted, heavy-duty type, with general-purpose NEMA ICS 6 enclosure in one of the following types: 16.H.1. Enclosure Type: Type 1. 16.H.2. Enclosure Type: Type 4. 16.H.3. Enclosure Type: Type 12.

16.I. Obstruction Detection Device: Provide each motorized door with indicated external automatic safety sensor able to protect full width of door opening. Activation of sensor immediately stops 08360-64 and reverses downward door travel. 16.I.1. Sensor Edge: Provide each motorized door with an automatic safety sensing edge, located within astragal or weather stripping mounted to bottom bar. Contact with sensor immediately stops and reverses downward door travel. Connect to control circuit using manufacturer's standard take-up reel or self-coiling cord. Sensing edge shall be operated by: 16.I.1.a. Electric. 16.I.1.b. Pneumatic. 16.I.1.c. Electric fail safe. 16.I.1.d. Pneumatic fail safe. 16.I.2. Photo-electric control: Provide each motorized door with a photo-electric device that will stop and reverse the downward door travel if the light beam is broken or blocked. Device shall be: 16.I.2.a. NEMA Type 1. 16.I.2.b. NEMA Type 4.

16.J. Limit Switches: Provide adjustable switches, interlocked with motor controls and set to automatically stop door at fully opened and fully closed positions.

16.K. Radio Controls: Provide 3 button radio transmitter to provide remote open, close, stop functionality. 16.K.1. Provide external antenna and coaxial wiring to receiver to enhance radio control reception.

16.L. Provide auxiliary chain hoist: for emergency manual operation while disconnecting motor, without affecting timing of limit switch. Mount disconnect and operator so they are accessible from floor level. Include interlock device to automatically prevent motor from operating when emergency operator is engaged.

PART 3 EXECUTION

3.1 EXAMINATION

1.A. Examine wall and overhead areas, including opening framing and blocking, with installer present, for compliance with requirements for installation tolerances, clearances, and other conditions affecting performance of Work in this Section. 1.A.1. Proceed with installation only after unsatisfactory conditions have been corrected.

1.B. If substrate preparation is the responsibility of another installer, notify Architect of unsatisfactory preparation before proceeding.

3.2 PREPARATION

2.A. Prepare surfaces using the methods recommended by the manufacturer for achieving the best 08360-65 result for the substrate under the project conditions.

3.3 INSTALLATION

3.A. Install overhead doors and track in accordance with approved shop drawings and the manufacturer's printed instructions.

3.4 PROTECTION

4.A. Protect installed products until completion of project.

4.B. Touch-up, repair or replace damaged products before Substantial Completion.

END OF SECTION

08360-66

Load more

  66

Copy Link