Updated 01-02-2013

GUIDELINES FOR LISTING AND REGISTRATION OF SUPPLIERS UNDER SECTION 180(m) WATER SERVICES INDUSTRY ACT 2006

1. INTRODUCTION

Any supplier who wishes to supply equipment, device, material, system or facility (collectively called as product) for water supply and sewerage system in Peninsular Malaysia, Wilayah-Wilayah Persekutuan Putrajaya and Labuan is required to be listed or registered with SPAN prior to carrying out such activities.

2. DEFINITION

For this purpose, a supplier refers to company incorporated in Malaysia (sole proprietorship, partnership, limited partnership or corporation) that has been established to offer goods and/or services.

3. PRODUCT CATEGORY

Registration of supplier will be classified in accordance to two (2) main product categories as listed below:

1 Updated 01-02-2013

Category A - Products that can undergo full certification to any SPAN recognised standards/specifications from any Certification Bodies recognised by SPAN.

- Products under this category and the respective approved standards are listed in Appendix I. Category B - Products without any specific standards/specifications or product with standards for test compliance that can undergo performance testing by any accredited test laboratory recognised by SPAN.

- Products under this category and the respective approved testing standards/requirements are listed in Appendix II.

4. APPLICATION FOR LISTING/REGISTRATION OF SUPPLIER

4.1 Application

Effective 6 February 2013, application for listing or registration of suppliers for products under category A and category B shall be made via on-line supplier e-registration at SPAN website.

4.2 Certificate of Conformity

Application for products in category A shall be accompanied with a copy of certificate of conformity issued by SPAN recognised certification bodies to show that product has complied with product standard.

2 Updated 01-02-2013

4.3 Certification Body

SPAN only recognises certificates produced by certification bodies which are accredited by Standard Malaysia under the Accreditation of Certification Bodies (ACB) Scheme and other international certification bodies recognised by Standard Malaysia through the Pacific Accreditation Cooperation (PAC) and International Accreditation Forum (IAF) Multilateral Recognition Arrangement (MRA).

List of accredited certification bodies recognised by SPAN can be referred to at Standard Malaysia website at www.standardmalaysia.gov.my or at www.apec-pac.org for certification bodies under the PAC MRA as well as at www.iaf.nu for certification bodies under the IAF MRA.

4.4 Test Report

Application for products under category B shall be accompanied with test report to show compliance to the testing standard/requirements (e.g. performance requirement of a product) as determined in Appendix II. Test report to be submitted for this purpose shall be the original copy and is written either in English or Bahasa Malaysia. Report in other languages shall be translated into either in English or Bahasa Malaysia before the submission to SPAN.

4.5 Testing Laboratory

SPAN only accepts testing report produced by testing laboratories which are accreditated by Standard Malaysia under the SAMM scheme and other international testing laboratories recognised by Standard Malaysia through the International Laboratory Accreditation Cooperation (ILAC) Mutual Recognition Arrangement (MRA) and International Accreditation Forum (IAF) Multilateral

3 Updated 01-02-2013

Recognition Arrangement (MLA). List of accredited testing laboratories can be referred to at Standard Malaysia website.

4 Updated 01-02-2013

4.6 Certified True Copy of Certificate

Copy of certificates (e.g. product certificate, HALAL certificate) shall be certified as a true copy by any of the following bodies:

(i) the certification body that produces the certificate (ii) Commission of Oath

5. APPROVAL FOR LISTING OF SUPPLIER AND PRODUCT UNDER CATEGORY A

5.1 Listing of Supplier

Any application under category A which has been approved will be listed in the “Listing of Supplier” at SPAN website.

5.2 Confirmation Letter

Confirmation letter to confirm the listing will be issued to the supplier.

5.3 Responsibilities of Supplier

All listed supplier under this category shall be responsible to ensure his product certificate is continuously maintained and valid throughout the listing period.

5 Updated 01-02-2013

5.4 Maintaining Supplier’s name in the Listing

Any listed supplier under this category is required to submit a copy of renewed product certificate on yearly basis in order to maintain his company and his product in the listing. Failing to comply with these requirements may lead to an automatic delisting of the supplier without prior notice.

6. APPROVAL FOR REGISTRATION OF SUPPLIER AND PRODUCT UNDER CATEGORY B

6.1 Certificate of Registration

Any application under category B which has been approved will be given a Certificate of Registration.

6.2 Validity of a Registration Certificate

The validity period of certificate of registration will be determine by SPAN and shall be valid for a period of not less than one year and not more than three years from the date of issuance.

6.3 Listing at the SPAN website

The approved supplier will be listed in the “List of Registered Supplier” at SPAN website.

6 Updated 01-02-2013

6.4 Responsibilities of a Registered Supplier

All registered supplier are responsible to adhere to all approval conditions as listed in the certificate of registration. Failing to comply with any of the conditions may lead to termination of registration.

6.5 Renewal of Certificate

Every application for renewal of certificate shall be made online not later than three months before the end of the expiry date.

7. PROCESSING TIME

7.1 Product Category A

When a completed application is received by SPAN, the processing time for listing of supplier at SPAN website and issuing confirmation letter will be completed within 3 working days.

7.2 Product Category B

For application which does not involve pilot project, certificate of registration will be issued to the approved supplier within 21 working days.

8. FEE

No fees are imposed for the application of listing or registration of supplier at this moment.

7 Updated 01-02-2013

9. USE OF SPAN LOGO

Use of SPAN logo is allowed for marketing purpose on product catalogue in the form of hard and electronic media and subject to the following conditions: (i) the logo cannot be printed on product to be supplied; (ii) the logo must be printed with listing or registration number; and (iii) SPAN logo cannot not be defaced, obstructed, misused, forged, falsified or altered.

Please refer to “Garis Panduan Penggunaan Logo SPAN” for details description on how to use SPAN logo.

10. FURTHER INFORMATION

For any further information about listing and registration of suppliers, please contact the department of Research, Development and Innovation of SPAN at the following contact number: 03 – 83179333/334/335 and speak to any of the following officer: Bazlan Mohd Noor (ext. 374)/ Natasha Khairuddin (ext. 218) / Zaidah Hassan (ext.219).

11. OFFENCE FOR GIVING FALSE OR MISLEADING INFORMATION

SPAN wish to highlight that it is an offence under Section 130 of the Water Services Industry Act 2006 for “a person who discloses or provides information to the Commission or its authorized officers that he knows or has reason to believe is false or misleading commits an offence and shall, on conviction, be liable to a fine not exceeding two hundred thousand ringgit or to imprisonment for a term not exceeding two years or to both.”

Research, Development and Innovation Division

8 Updated 01-02-2013

Feb 2012

9 Updated 01-02-2013

APPENDIX I

(1) Water supply products under Category A and the respective approved standards

Items Standard Number Standard Title

(a) Water Pipes

Specification for Polyethylene (PE) MS 1058: Part 2: 2005 Piping Systems for Water Supply : Part 2 : Pipes (Forth Revision)

Polyethylene Plastics Piping Systems – (PE) Pipes ISO 4427–2 : 2007 Polyethylene (PE) Pipes and Fittings for Water Supply – Part 2 : Pipes

Polyehtylene (PE) Pipes – General DIN 8075 (1999 – 08) quality requirements, testing. Plastics Piping Systems for Hot and ISO 22391: Part 2: Cold Water Installations – PE-RT Pipes 2007 Polyethylene of Raised Temperature Resistance (PE-RT) : Part 2 : Pipes Multilayer Piping Systems for Hot PE-RT/AL/PE-RT BS EN ISO 21003 -1: and Cold Water Installation Inside Pipes 2008 Buildings. General Plastic Piping Systems for Hot and Cold Water Installations – MS 1736 : Part 2 : PE-X Pipes Crosslinked Polyethylene (PE-X): 2004 Part 2 : Pipes (ISO 15875-2:2002 MOD) Standard Specification for PE Aluminium Polyethylene / Aluminium / (PE-AL-PE) ASTM F1282 – 03 Polyethylene (PE-AL-PE) Composite Pipes Pressure Pipes

MS 628: Part 1: 1999 Specification for Unplasticised PVC AMD.1: 2001 & AMD.2: (uPVC) Pipes for Water Supply : 2002 Part 1: Pipes (1st revision) Unplasticized Polyvinylchloride Plastics Piping Systems for Water (uPVC) Pipes Supply and for Buried and Above- BS EN ISO 1452-2: Ground Drainage and Sewerage 2009 Under Pressure. Unplasticized Poly(vinyl Chloride) (PVC U). Pipes

i Updated 01-02-2013

Items Standard Number Standard Title

Chlorinated Poly (Vinyl Chloride) MS 2045 : 2007 (PVC-C) Plastic Hot-and-Cold-Water Distribution Systems – Specification.

Chlorinated Standard Specification for Polyvinylchloride ASTM D2846 / Chlorinated Polyvinyl Chloride (cPVC) Pipes D2846M – 09b (cPVC) Plastic Hot and Cold Water Distribution System. Chlorinated Poly (Vinyl Chloride) MS 1757 : Part 1 : (PVC-C) – Plastic Piping System – 2008 Part 1 : Specification for Schedule 40 & 80 Pipes. Acrylonitrile-Butadiene Styrene (ABS) Piping Systems for Pressure MS 1419: Part 1: 2007 Applications – Part 1: Specification Acrylonitrile- for Compounds, Pipes and Fittings Butadiene- (First Revision) Styrene (ABS) Pipes Acrylonitrile Butadiene Styrene AS/NZS 3518 : 2004 (ABS) Compounds, Pipes and Fittings for Pressure Application.

Plastics Piping Systems for Hot and ISO 15874: Part 2: Cold Water Installations – 2003 Polypropylene Polypropylene (PP). Part 2: Pipes (PP) Pipes Polypropylene (PP) Pipes – PP-H, DIN 8078: 2008 PP-B, PP-R, PP-RCT – General Quality Requirements and Testing

Polybutylene (PB) Plumbing Pipe AS/NZS 2642-2: 2008 Systems – Polybutylene (PB) Pipe for Hot and Cold Water Applications. Polybutylene (PB) Pipes Plastics Piping Systems for Hot and MS ISO 15876-2 : Cold Water Installations – 2004, AMD. 1: 2009 Polybutylene (PB) Part 2 : Pipes (ISO 15876-2:2003, MOD) Plastics Piping System for Pressure Glass Reinforced and Non-pressure Water Supply – Plastic (GRP) ISO 10639: 2004 Glass Reinforced Thermosetting Pipes Plastics (GRP) Systems Based On Unsaturated Polyester (UP) Resin

Filament- Standard Specification for Filament- ASTM D 2996-01 : Wounded Wound “Fibreglass” (Glass-Fiber- 2007 Fibreglass Pipes Thermosetting-Resin) Pipe

ii Updated 01-02-2013

Items Standard Number Standard Title

Steel Pipes, Joints and Specials for BS 534: 1990 Water and Sewage Non-Alloy Steel Tubes and Fittings for the Conveyance of Aqueous MS 1968 : 2007 Liquids Including Water for Human Steel Pipes Consumption – Technical Delivery Conditions Non-Alloy Steel Tubes and Fittings for the Conveyance of Aqueous BS EN 10224 : 2002 Liquids Including Water for Human Consumption – Technical Delivery Conditions Seamless, Welded and Heavily Cold MS 1841: 2010 Austenitic Stainless Steel Pipes - Stainless Steel Specification (SS) Pipes - Standard Specification for Industrial Seamless, Welded, and Heavily ASTM A312/A312M-11 Cold Worked Austenitic Stainless Steel Pipes Welded Stainless Steel Tubes for MS 1988: 2007 the Conveyance of Water and Other Aqueous Liquids – Technical Delivery Conditions Welded Stainless Steel Tubes for Stainless Steel the Conveyance of Aqueous Liquids (SS) Light Gauge BS EN 10312 : 2002 Including Water for Human Tubes Consumption. Technical Delivery Conditions Light Gauge Stainless Steel Pipes JIS G 3448: 2004 for Ordinary Piping

Ductile Iron Pipes, Fittings, MS 1919: 2006 Accessories and Their Joints for Water Pipelines – Requirement and Ductile Iron (DI) Test Method Pipes Ductile Iron Pipes, Fittings, Accessories and Their Joints for BS EN 545 : 2010 Water Pipelines – Requirement and Test Method

Copper and Copper Alloys. Seamless, Round Copper Tubes for Copper Tubes BS EN 1057: 1996 Water and Gas in Sanitary and Heating Applications

Steel Pipe with Steel Pipes of Lining Plastic for CJ/T 137: 2001 Plastic Lining Water Supply

iii Updated 01-02-2013

Items Standard Number Standard Title

(b) Water fittings

Polyethylene Pipes for Water BS EN 12201-3:2003 Supply. Part 3 : Fittings

Polyethylene (PE) Polyethylene (PE) Piping Systems MS 1058: Part 3: 2006 Fittings for Water Supply – Part 3 : Fittings

Fittings for Polyethylene (PE) Pipes AS/NZS 4129: 2008 for Pressure Applications. Pipe Joints and Components of HDPE Joints Polyethylene (PE) for Pipes Under DIN 16963 : Part 5 : Assemblies and Pressure, PE 80 and PE 100 – Part (1999-10) Fittings 5 : General Quality Requirements, Testing. Plastics Piping Systems for Hot and MS 1736 : Part 3 : Cold Water Installations – PE-X Fittings 2004 Crosslinked Polyethylene (PE-X): Part 3 : Fittings Plastics piping systems for hot and cold water installations – PE-RT Fittings ISO 22391 – 3 : 2007 Polyethylene of raised temperature resistance (PE-RT) – Part 3 : Fittings Multilayer piping systems for hot and PE-RT/AL/PE-RT ISO 21003 – 3 : 2008 cold water installations inside Fittings buildings – Part 3 : Fittings Polyethylene/aluminium and cross- linked polyethylene/aluminium PPO Fittings ISO 4176 : 1994 macro-composite pipe systems for pressure applications Specification for Performance BS 5114: 1975 (1981) Requirements for Joints and Amd.2 – 1987 Compression Fittings for Use with Nylon Joints and Polyethylene Pipes Compression Plastics Pipes and Fittings – Fittings for use Mechanical-Joint Compression with HDPE Pipes ISO 14236: 2000 Fittings for Use with Polyethylene Pressure Pipes in Water Supply Systems. Plastics Piping Systems for Hot and ISO 15874: Part 3: Cold Water Installations – 2003 Polypropylene (PP) – Part 3 : Fittings Polypropylene Pipe Joints and Elements for (PP) Fittings Polypropylene (PP) for Pipes Under DIN 16962-5: 2000 Pressure, PP-H 100, PP-B 80 and PP-R 80 – Part 5: General Quality Requirements, Testing.

iv Updated 01-02-2013

Items Standard Number Standard Title

Polybutylene (PB) Plumbing Pipe Systems – Mechanical Jointing AS/NZS 2642-3: 2008 Fittings for Use with Polybutylene (PB) Pipes for Hot and Cold Water Polybutylene (PB) Applications Fittings Plastics Piping Systems for Hot and MS ISO 15876 – 3 : Cold Water Installations – 2004 Polybutylene (PB) Part 3 : Fittings

Specification for Unplasticised PVC (uPVC) Pipes for Water Supply : MS 628: Part 2: Part 2: Joints and Fittings for Use Section 2.1: 1999 with uPVC Pipes: Section 2.1: uPVC Joints and Fittings Plastics Piping Systems for Water Supply and for Buried and Above- BS EN ISO: 1452-3: Ground Drainage and Sewerage 2009 Under Pressure. Unplasticized Unplasticized Poly(vinyl Chloride) (PVC U). Polyvinylchloride Fittings. (uPVC) Joints / Joints and Fittings for use with Fittings Unplasticized PVC Pressure Pipes. Injection Moulded Unplasticized BS 4346-1: 1969 PVC Fittings for Solvent Welding for use with Pressure Pipes, Including Potable Water Supply. Joints and Fittings for use with Unplastisized PVC Pressure Pipes. BS 4346-2: 1970 Mechanical Joints and Fittings, Principally of Unplasticized PVC. Standard Specification for ASTM D2846 / Chlorinated Polyvinyl Chloride D2846M – 09b (cPVC) Plastic Hot and Cold Water Distribution System. Chlorinated Poly (Vinyl Chloride) MS 1757 : Part 1 : (PVC-C) – Plastic Piping System – Chlorinated 2008 Part 2 : Specification for Schedule Polyvinylchloride 40 Socket-type Pipe Fittings. (uPVC) Fittings Chlorinated Poly (Vinyl Chloride) MS 1757 : Part 1 : (PVC-C) – Plastic Piping System – 2008 Part 3 : Specification for Schedule 80 Pipe Fittings. Chlorinated Poly (Vinyl Chloride) MS 2045 : 2007 (PVC-C) Plastic Hot-and-Cold-Water Distribution Systems – Specification.

v Updated 01-02-2013

Items Standard Number Standard Title

Acrylonitrile-Butadiene Styrene (ABS) Piping Systems for Pressure Acrylonitrile- MS 1419: Part 1: 2007 Applications – Part 1: Specification Butadiene- for Compounds, Pipes and Fittings Styrene (ABS) (First Revision) Fittings Acrylonitrile Butadiene Styrene AS/NZS 3518: 2004 (ABS) Compounds, Pipes and Fittings for Pressure Application Plastics Piping System for Pressure Glass Reinforced and Non-pressure Water Supply – Plastic (GRP) ISO 10639: 2004 Glass Reinforced Thermosetting Fittings Plastics (GRP) Systems Based On Unsaturated Polyester (UP) Resin Steel Pipes, Joints and Specials for BS 534: 1990 Water and Sewage Steel Pipe Non-alloy steel tubes and fittings for Specials the conveyance of aqueous liquids MS 1968 : 2007 including water for human consumption – technical delivery conditions Stainless Steel Pipework – Stainless Steel Fittings (SS) Threaded ISO 4144: 2003 Threaded in Accordance with ISO 7- Fittings 1. Wrought Austenitic Stainless Steel MS 1842: 2010 Piping Fittings – Specification (First Stainless Steel Revision). (SS) Welded Standard Specification for Wrought Fittings ASTM A403/A403M- Austenitic Stainless Steel Piping 10a Fittings Stainless Steel (SS) Press SAS 322: 2003 Stainless Steel Press Fittings Fittings Ductile Iron Pipes, Fittings, Accessories and Their Joints for MS 1919: 2006 Water Pipelines – Requirement and Ductile Iron Test Method Fittings Ductile Iron Pipes, Fittings, Accessories and Their Joints for BS EN 545 : 2010 Water Pipelines – Requirement and Test Method Copper Fittings Copper and Copper Alloys. Plumbing Fittings. Fittings with BS EN 1254-1: 1998 Short Ends for Capillary Brazing to Copper Tubes. BS EN 1254-2: 1998 Copper and Copper Alloys. Plumbing Fittings. Fittings with Compression Ends for Use with Copper Tubes.

vi Updated 01-02-2013

Items Standard Number Standard Title

Copper and Copper Alloys. Plumbing Fittings. Fittings BS EN 1254-4: 1998 Combining Other End Connections with Capillary or Compression Ends.

Steel Fittings with Malleable Iron Threaded Fittings of CJ/T 136: 2001 Plastic Lining Lining Plastic for Water Supply.

JKR Standard Specification for Spesifikasi JKR 20200- Detachable Joints and Variable Variable Adapter 0045-99 Adaptors for uPVC, Ductile Iron and AC Pipes.

JKR Standard Specification For Spesifikasi JKR 20200- Flange Adapter Flexible Couplings and Flange 0048-99 Adaptors.

JKR Standard Specification For Spesifikasi JKR 20200- Flexible Coupling Flexible Couplings and Flange 0048-99 Adaptors.

JKR Standard Specification for Spesifikasi JKR 20200- Detachable Joints and Variable Detachable Joint 0045-99 Adaptors for uPVC, Ductile Iron and AC Pipes.

Spesifikasi JKR 20200- JKR Standard Specification for Ferrous Saddle 0044-99 Ferrous Saddles.

Spesifikasi JKR 20200- JKR Standard Specification for 0042-99 Ductile Iron Pillar Hydrants. Pillar Hydrant

MS 1395: 1996 Specification for Pillar Hydrants

JKR Standard Specification for Ductile Iron (DI) Spesifikasi JKR 20200- Ductile Iron Strainer (DN 50 to DN Strainer 0100-01 600)

Spesifikasi JKR 20200- JKR Standard Specification for Swivel Ferrules 0174-04 Ferrules

vii Updated 01-02-2013

Items Standard Number Standard Title

Under Pressure Ferrules – Specification (First MS 1396: 2006 Vertical Ferrules Revision)

Gully Tops and Manhole Tops for Vehicular and Pedestrian Areas. Manhole Cover BS EN 124 : 1994 Design Requirements, Type Testing, Marking, Quality Control.

(c) Tank

Glass Coated / Glass Lined / AWWA D103-97, Factory-Coated Bolted Steel Tanks Glass Fused / ANSI/AWWA D103-09 For Water Storage Epoxy Coated / Epoxy Lining

Polyethylene (PE) Tanks For Cold MS 1225 : Pt 1 : 2007 Water Storage; Part 1: Capacity up PE / HDPE to 600G (Second Revision) Tanks Storage Tank Polyethylene (PE) Tanks For Cold MS 1225 : Pt 2: 2006 Water Storage; Part 2: Capacity more than 600G (First Revision)

GRP/FRP Specification for glass reinforced Sectional Water MS 1390 : 2010 polyester panels & panel water Tank tanks

Specification for glass fibre reinforced cistern of one-piece and BS EN 13280 : 2001 sectional construction for storage above ground of cold water Specification for Fibreglass Water MS 1241 : 1991 Tanks – Effective Capacity of Less FRP One-Piece Than 2000L Water Tank Glass Fibre Reinforced Plastic Cisterns for Cold Water Storage. BS 7491: Pt 2 : 1992 Specification for one piece cisterns of nominal capacity for 500L to 25000L.

Pressed Steel Sectional Specification for Pressed Steel BS 1564 : 1975 Rectangular Sectional Rectangular Tanks Tank Panel

viii Updated 01-02-2013

Items Standard Number Standard Title

Stainless Steel Stainless Steel Water Tanks (With JKR 20200-0041-99 Storage Tank Effective Capacity Up to 15,000L)

Stainless Steel Storage Tank CNS 9443 : 1989 Stainless Steel Storage Tanks (Rectangular / Panel Tank)

(d) Valves Industrial Valves. Metallic Butterfly Butterfly Valve BS EN 593 : 2004 Valves

Ductile Iron Air Valves JKR 20200-0097-01 (Revised Edition 2001)

Ductile Iron Air Valves JKR 20200-0043-99 (Revised Edition 1999)

Air Release, Air Vacuum, and ANSI / AWWA C512- Air Valve Combination Air Valve for 2004 Waterworks Service. Valves for Water Supply. Fitness for Purpose Requirements and BS EN 1074-4 : 2000 Appropriate Verification Tests. Air Valves. Specification for Double Flanged MS 1049 : 1986 Cast Iron Wedge Gate (sluice) valves for waterworks purposes. Industrial Valves. Copper Alloy Gate BS EN 12288 : 2010 Valves Industrial Valves. Cast Iron Gate BS EN 1171 : 2002 Valves Ductile Iron Type B Large Sluice Gate Valve JKR 20200-0077-00 Valves (DN700-DN1800)

Valves for Waterworks Purposes. BS 5163-1 : 2004 Predominantly key-operated cast iron gate valves. Code of practice Valves for Waterworks Purposes. Stem Caps for use on isolating BS 5163-2 : 2004 valves and associated water control apparatus. Specification. BS EN 12334 : 2001 Industrial Valves. Cast Iron Check Valves.

ix Updated 01-02-2013

Items Standard Number Standard Title

Industrial Valves. Steel Check BS EN 14341 : 2006 Valves

Copper Alloy Check Valve for BS 1953 : 1964 general purposes. Check Valve Specification for copper alloy globe, BS EN 12288 : 2003 globe stop, check and gate valves

Valves for Water Supply – Fitness for Purpose Requirements and Control Valve BS EN 1074-5:2001 Appropriate Verification Tests. Part 5 : Control Valve Stopvalves – Specification (First MS 1022 : 2005 Revision)

Specification for servicing valves BS 6675 : 1985 (copper alloy) for water services.

Stopvalve Building Valves. Copper alloy BS EN 1213 : 2000 stopvalves for potable water supply in buildings. Test & Requirements.

Specification of Mechanical JKR 20200-0055-99 Stopvalve for water supply usage

Piston Type Ball Valves (Excluding BS 1212 : Part 1 : 1953 Floats) Ball Valves Diaphragm Type (Brass Body) ball BS 1212 : Part 2 : 1971 Valves (Excluding Floats)

Fire Hydrant Systems Equipment. BS 5041 : Pt 1 : 1987 Specification for landing valves for wet risers Landing Valve Fire Hydrant System Equipment. BS 5041 : Pt 3 : 1975 Specification for landing valves for dry risers. Mixing Valves (Manually Operated) Mixing Valve for ablutionary and domestic (Manually BS EN 1286 : 1999 purposes. Operated) Non Thermostatic, non- compensating mixing valves Float Operated MS 1882 : 2005 Piston Type Float Operated Valves Valve – Specification

x Updated 01-02-2013

Items Standard Number Standard Title

JKR 20200-0059-99 Specification of Brass Float Valves

Building Valves. Water Pressure Pressure Valves and Combination Water BS EN 1567 : 2000 Reducing Valves Reducing Valves. Requirements and Test. Penstocks for use in Water and BS 7775 : 2005 Other Liquid Flow Applications. Specification. Penstock JKR Standard Specification for JKR 20200-0108-01 Penstocks (Revised Edition 2001)

(e) Back flow preventer Devices to prevent pollution by backflow of potable water. Hose BS EN 14454 : 2005 Dual Check Union backflow preventer DN15 to Backflow DN32 inclusive. Family H, Type A. Preventer Plumbing and drainage - Water AS/NZS 3500.1:2003 Services Devices to prevent pollution by backflow of potable water. Reduced BS EN 12729 : 2002 Controllable backflow preventer with Pressure Zone reduced pressure zone. Family B, Assembly Type A Plumbing and drainage - Water AS/NZS 3500.1:2003 Services (f) Meter Water Meters Intended for the Electromagnetic / metering of Cold Potable Water and Ultrasonic OIML R 49-1 Hot Water Flowmeter Part 1 : Metrological and technical requirement Water Meters Intended for the metering of Cold Potable Water and OIML R 49-1 Hot Water Part 1 : Metrological and technical Water Meter requirement Measurement of Water Flow in fully charged closed conduits – Meters for ISO 4064-1 : 2005 Clod Potable Water and Hot Water – Part 1 – Specification (g) Taps & Mixer

xi Updated 01-02-2013

Items Standard Number Standard Title

Sanitary Tapware. Single Taps and combination Taps For Water Supply BS EN 200 : 2008 Systems of Type 1 and Type 2. Bib Tap / Pillar General Technical Specification. Tap/ Faucet AS / NZS 3718 : 2005 Water Supply – Tap ware

Specification for draw off taps with MS 1461 : 1999 metal bodies for water service

Sanitary tapware. Mechanical BS EN 817 : 2008 mixing valves (PN 10). General technical specifications. Mixer Mixing Valves (manually operated) BS EN 1286 : 1999 for ablutionary and domestic purposes. (h) Water Closet

Vitreous China Water Closet Pans – MS 1522 : 2007 Specification (Second Revision) Water Closet Pan Specification for quality of Vitreous MS 147 : 2001 China Sanitary Appliances (First Revision)

Vitreous China Water Closet Pans – MS 1522 : 2007 Specification (Second Revision)

Moulded One- Specification For WC Flushing MS 795 : 2002 piece Water Cisterns & Flush Pipe Closet Specification for quality of Vitreous MS 147 : 2001 China Sanitary Appliances (First Revision)

(i) Water Closet and Flushing Cistern

Water Closet Specification For WC Flushing Flushing Cistern MS 795 : 2002 Cisterns & Flush Pipe & Flush Pipes

(j) Flush valve

JKR Standard Specification For Flush Valve JKR 20200-0130-01 Flush Valve

(k) Sanitary Appliances

xii Updated 01-02-2013

Items Standard Number Standard Title

Urinal bowls, Pedestal, Bidets, WC Pans Specification for quality of Vitreous Cistern & Cover MS 147 : 2001 China Sanitary Appliances (First Revision)

Wash Basin

(l) Urinals

Urinals MS 1799 : 2008 Urinals - Specification

(m) Water Treatment Chemical – Coagulant & Flocculant. Aluminium Sulphate for Use in MS 699:2008 Potable Water Supply –Specification Product Based on (Second Revision) Aluminium Liquid polyaluminium chloride for MS 1454:2007 use in potable water supply – specification (first revision), 2007

Specification for Sodium Aluminate MS 1572:2003 used for potable water supply

Specification for liquid ferric chloride MS 1450:1999 for potable water treatment

Specification for liquid ferric Product Based on MS 1452:1999 Iron sulphate for potable water treatment

Guidelines for the application of MS 1456:1999 liquid ferric based salts in potable water treatment

Poly(polydiallyldimethyl ammonium Product Based on MS 1930:2007 chloride) or polyDADMAC for use in PolyDADMAC potable water supply

Product based on Polyacrylamides for use in potable MS 1928:2007 Polyacrylamide water supply (specification)

Product based on Polyamines for use in potable water MS 1929: 2007 Polyamine supply (specification)

(n) Water Treatment Chemical – Softening Agent and PH Adjustment.

xiii Updated 01-02-2013

Items Standard Number Standard Title

Hydrated Lime / Hydrated Lime and slurry lime for Calcium MS 1836:2005 use in potable water supply Carbonate Sodium Specification for soda ash (sodium Carbonate / Soda MS 1551 : 2002 carbonate) used for potable water Ash supply (o) Water Treatment Chemical – Chemicals for Disinfection.

Specification for liquid chlorine used Chlorine MS 171:2003 for potable water supply

Sodium Sodium Hypochlorite for use in MS 1718:2003 Hypochlorite potable water supply Specification for calcium Calcium MS 1548:2003 hypochlorite use for potable water Hypochlorite supply 2003 Specification for potassium Potassium MS 1576: 2003 permanganate used for potable Permanganate water supply

Specification for Copper Sulphate Copper Sulphate MS 1571:2003 used for potable water.

(p) Water Treatment Chemical – Chemicals for Flouridation.

Specification for sodium fluoride Sodium Flouride MS 1573 : 2003 used for potable water supply

Sodium silicofloride for use in Sodium MS 1724:2004 potable water supply specification Silicoflouride 2004 (q) Water Treatment Chemical – Filter Media & Other Chemicals.

Specification for silica sand for the Sand MS 847: 1983 manufacturer of sodium silicate.

Sodium (Specification) for sodium hydroxide Hydroxide / MS 700: 1981 (technical grades) Caustic Soda Powdered activated carbon for use MS 873:2005 in potable water supply – specification Activated Carbon Granular activated carbon for use in MS 1815 : 2005 potable water supply (specification)

xiv Updated 01-02-2013

(2) Sewerage products under Category A and the approved respective standards

Items Standard Number Standard Title

Package TS SPAN 1401:2010 Technical Specifications for Sewage plant Treatment System, Part 1: Prefabricated Tanks - Packaged Plants.

Septic tank MS 2441-1:2012 Onsite sewage treatment units Part 1: Prefabricated septic tanks specifications (Note: Standards had been approved, pending publication by end Feb 2012)

Manholes MS 881: Pt 1 Specification for precast concrete pipes and fittings for drainage and sewerage

Manhole BS EN 124 Gully tops & manhole tops for vehicular & cover pedestrian areas design req., type testing, marking, quality control

Vitrified clay a) MS 1061 Vitrified clay pipes and fittings and pipes pipe joints for drains and sewers : Part 1 : Requirement (First Revision)

b) BS EN 295-1 Vitrified clay pipes and fittings and pipe joints for drains and sewers.

Jacking pipe Jacking pipe

c) BS EN 295-7 Vitrified clay pipes and fittings and pipe joints for drains and sewers. Requirements for vitrified clay pipes and joints for pipe jacking

Reinforced MS 881: Pt 1 Specification for precast concrete concrete pipe pipes and fittings for drainage and sewerage Part:2 Specification for Inspection Chambers and gullies

AS 4058 Precast concrete pipes (pressure and non-pressure)

Jacking pipe

BS 5911-1 Concrete pipes and ancillary concrete xv Updated 01-02-2013

Items Standard Number Standard Title

products

HDPE pipe Profile Wall Profile Wall

DIN 16961 Thermoplastics pipes and fittings with profiled wall and smooth pipe inside

Solid Wall Solid Wall

MS 1058 Polyethylene (PE) piping systems for water supply

Ductile iron BS EN 598 Ductile iron pipes, fittings, accessories pipe and their joints for sewerage applications. Requirements and test methods

Glass-fibre BS 5480 Specification for GRP pipes, joints and reinforced fittings for use for water supply or pipe sewerage

ASTM D 3262 Specification for GRP Sewer Pipe

PVC pipe AS/NZS 1477 PVC pipes and fittings for pressure (PVC-U, applications PVC-M, PVC- C) BS 4660 Specification for unplasticized polyvinyl chloride (PVC-U) pipes and plastics fittings of nominal sizes 110 and 160 for below ground gravity drainage and sewerage

BS 5481 Specification for unplasticized PVC pipe and fittings for gravity sewers

JIS K 6741 uPVC Pipes for General Fluids (Excluding Potable Water )

xvi Updated 01-02-2013

Items Standard Number Standard Title

MS 979 Specification for unplasticizies sewerage pipe and fitting Part 1: pipes of diameter 100mm and 155mm

MS 979 Part 2 Pipes of diameter 200mm and above

AS/NZS 1477 PVC pipes and fittings for pressure application

BS EN 1401-1 Unplasticized Polyvinyl Chloride (PVC-U) Fittings For Non-Pressure Underground Drainage and Sewerage

ABS pipe MS 1419: Part 1 Specification for acrylonitrile butadiene styrene (ABS) pipes and fittings for pressure application Part 3 Solvent cement & priming (cleaning) fluids for use with ABS pipes & fittings

Steel Pipes, Joints and Specials for Steel Pipes BS 534 Water and Sewage

Standard Specification for Seamless, Stainless ASTM A312 Welded, and Heavily Cold Worked Steel Pipes Austenitic Stainless Steel Pipes

Stainless Standard Specification for Wrought ASTM A403 Steel Fittings Austenitic Stainless Steel Piping Fittings

Penstock BS7775 Penstocks for use in water and other (Wall liquid flow applications. Specification mounted, channel type, weir gate)

Cast Iron Pipes & ISO 6594 Cast Iron Pipes & Fittings - Spigot Series Fittings

xvii Updated 01-02-2013

Items Standard Number Standard Title

Gate valve MS 1049 Specification for double flanged cast iron wedge gate (sluice) valves for waterworks purposes

BS 5163 Valves for waterworks purposes. Stem caps for use on isolating valves and associated water control apparatus. Specification

EN 1074 (Part 2) Valves for water supply - Fitness for purpose requirements and appropriate verification tests - Part 2: Isolating valves

BS EN 1171 Industrial valves. Cast iron gate valves

Check valve BS EN 12334 Industrial valves. Cast iron check valves

Butterfly valve BS EN 593 Industrial valves. Metallic butterfly valves

Air/air release JKR20200-0097-01 JKR specification for air valves valve (as of July 2012)

xviii Updated 01-02-2013

APPENDIX II

(1) Water supply products under Category B and the respective standards/requirements

Product Testing Standards / Requirements

(a) Lining / coating / waterproofing / sealant / adhesive

Suitability of Non-Metallic Products for Use in Contact with Water MS 1583 : Part 1 : Intended for Human Consumption 2003 with Regard to Their Effect on the Quality of the Water : Part 1 : Lining / coating / Specification waterproofing / sealant / adhersive Suitability of Non-Metallic Products for Use in Contact with Water BS 6920 – 1 : 1996 Intended for Human Consumption with Regard to Their Effect on the Quality of the Water : Specification Testing of Products for Use in AS/NZS 4020: 2005 Contact with Drinking Water

(b) Tank

Structural Use of Steelwork in Cylindrical Double Building Part 1 : Code of Practice for BS 5950-1:2000 Fold System Design – Rolled and Welded Section. Steel Plate, Sheet & Strip. Carbon Corrugated Steel BS 1449:Pt 1: 1991 and carbon-manganese sheet and Panel With strip. Polyethylene-Lined SS 245:1995 (Cl. Specification for Glass Reinforced Water Storage Tank 10.2.1 & Polyester Sectional Water Tank Cl 10.2.2)

(c) Pump

Rotodynamic pumps – Hydraulic Pump ISO 9906 : Performance Acceptance Tests – Grades 1 and 2.

(d) Chemical for Water Treatment

Drinking Water Treatment Chemical Chlorine Dioxide NSF/ANSI 60-2011 – Health Effects (for disinfection &

i Updated 01-02-2013

Chemical Used for Treatment of oxidation) BS EN 12671:2009 Water Intended for Human – Consumption – Chlorine Dioxide Generated in Situ

All kind of imported NSF/ANSI 60-2011 Drinking Water Treatment Chemical polymer for – Health Effects flocculant

(e) Small Water Treatment System

Small Water Treatment System/ Require for a pilot project to show that the system work as Compact Water claimed and treated water produced comply with the treatment System National Standard for Drinking Water.

(f) New Innovative Product for Water Treatment

Any product which is not listed in category Require for a pilot project to show that the product/system A or B for water work as claimed. supply application

(as of July 2012)

ii Updated 01-02-2013

(2) Sewerage products under Category B and the respective standards/requirements

Product Testing Standards / Requirements

Small Sewage Treatment CAN/CSA B66-05 Design, material and System manufacturing requirements for prefabricated septic tanks and sewage holding tanks.

(Note: Standards is only for prefabricated tanks components. Conformity assessment for treatment efficiency is subject to either pilot project for new application or sampling & testing by 3rd party for existing installation)

Screw conveyor a) BS 4409-1 Screw conveyors. Specification for fixed trough type.

Pump (Centrifugal- a) BS EN ISO 5198 Centrifugal, mixed flow and submersible, end suction, axial pumps. Code for hydraulic performance self priming) tests. Precision class.

b) BS EN ISO 5199 Technical specifications for centrifugal pumps. Class II.

c) BS EN ISO 9905 Technical specifications for centrifugal pumps. Class I.

d) BS EN ISO 9908 Technical specifications for centrifugal pumps. Class III.

e) ISO 9906 Rotodynamic pumps. Hydraulic performance acceptance tests - Grades 1 and 2.

f) JIS B 8325 Submersible Motor Pumps for Sump.

Pump (Positive displacementa) BS EN 14343 Rotary positive displacement pumps. - screw, lobe) Performance tests for acceptance.

Surface aerator, brush a) BS EN 12255-15 Wastewater treatment plants. aerator, paddle wheel Measurement of the oxygen transfer in clean aerator, hydrojet aerator, water in aeration tanks of activated sludge plants ejector, aspirating aerator, submersible aerator, diffuser b) ASCE/EWRI 2-06 Measurement of oxygen transfer in clean water

i Updated 01-02-2013

Product Testing Standards / Requirements

(Note: Standards for material is subject to manufacturer recommendations)

Mixer, agitator a) BS ISO 21630 Pumps. Testing. Submersible mixers for wastewater and similar applications.

Air blower For blowing application a) JIS B 8341 Testing methods for displacement compressors.

For vacuum application a) BS ISO 21360 Vacuum technology. Standard methods for measuring vacuum-pump performance. General description.

Vacuum sewerage system a) BS EN 1091 Vacuum sewerage systems outside buildings b) WSA 06 Vacuum sewerage code of Australia

Vacuum pump

a) BS ISO 21360 Vacuum technology. Standard methods for measuring vacuum-pump performance. General description.

CIPP Sewer liner a) BS EN 13566 Part 1 – 4 Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks b) ASTM F2019-03, Standard Practice for Rehabilitation of Existing Pipelines and Conduits by the Pulled in Place Installation of Glass Reinforced Plastic (GRP) Cured-in- Place Thermosetting Resin Pipe (CIPP) c) ASTM D5813 Standard Specification for Cured- In-Place Thermosetting Resin Sewer Piping Systems

FRP slip lining & HDPE lining

a) BS EN 13566 Part 1 – 4 Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks

b) BS EN ISO 178 Plastics. Determination of ii Updated 01-02-2013

Product Testing Standards / Requirements

flexural properti

Grit & Grease Removal – Require for a pilot project to show that the Grit & grease collector/ Grit product/system work as claimed. collector/ Grease collector

Clarifier/ Sedimentation - Require for a pilot project to show that the Sludge scrapper & scum product/system work as claimed. skimmer/ Sludge scrapper/ Scum skimmer

Gravity thickener Require for a pilot project to show that the product/system work as claimed. Odour Control Require for a pilot project to show that the & Treatment product/system work as claimed.

iii