SECTION 10 5113

METAL VENTED WARDROBE LOCKERS

PART 1 GENERAL

1.1 SUMMARY

A. Section Includes: 1. Metal vented wardrobe locker units with hinged doors.

B. Related Sections: 1. Division 01: Administrative, procedural, and temporary work requirements.

1.2 REFERENCES

A. ASTM International (ASTM): 1. A167 - Standard Specification for Stainless and Heat-Resisting Chromium-Nickel Steel Plate, Sheet, and Strip. 2. A653/A653M - Standard Specification for Steel Sheet, Zinc-Coated (Galvanized) or Zinc-Iron Alloy Coated (Galvannealed) by the Hot-Dip Process.

1.3 SYSTEM DESCRIPTION

A. Metal Lockers: 1. Configuration: Single tier. 2. Size: [12] [18] [24] [30] [36] [42] inches wide x 24 inches deep x [60] [66] [72] inches high.

1.4 SUBMITTALS

A. Submittals for Review: 1. Shop Drawings: Include dimensioned plans and elevations showing locker layout and relationship to adjacent construction. 2. Product Data: Manufacturer's descriptive data. 3. Samples: 3-1/4 x 1-1/2 inch paint samples [showing available colors.] [in each color.]

B. Sustainable Design Submittals: 1. Recycled Content. 2. Regional Materials.

1.5 QUALITY ASSURANCE

A. Manufacturer Qualifications: Minimum [10] [__] years [documented] experience in work of this Section.

B. Installer Qualifications: Minimum [2] [__] years [documented] experience in work of this Section.

C. Accessibility: Conform to [applicable accessibility code] [____] for accessible locker units.

1.6 WARRANTIES

A. Provide manufacturer’s 5 year warranty against defects in materials and workmanship.

PART 2 PRODUCTS

2.1 MANUFACTURERS

Tiffin Metal Products 10 5113-1 Metal Vented Wardrobe Lockers 08/19/10 A. Products are based upon Metal Personnel Duty Lockers as manufactured by Tiffin Metal Products and distributed by Storage Systems USA ([email protected], 800-698- 8990)

2.2 MATERIALS

A. Steel Sheet: 1. ASTM A1008/A1008M. 2. Recycled content: Minimum 80 percent recycled steel, with minimum 80 percent classified as post consumer.

**** OR ****

B. Stainless Steel: 1. ASTM A167, Type 304, rollable temper. 2. Recycled content: Minimum 60 percent recycled stainless steel, with minimum 60 percent classified as post consumer.

2.3 FABRICATION

A. Construction: 1. Doors, shelves, and reinforcements: Minimum 16 gauge [stainless] steel. 2. Top, bottom, back and sides: Minimum 14 gauge [stainless] steel. 3. Top, bottom, and front perforated for ventilation. 4. Shelves spaced 2 inches off back panel for ventilation.

B. Doors: 1. Louverless, self-closing. 2. Door hinges: 14 gauge [stainless] steel, continuous type, concealed, 180 degree opening.

C. Frames: 1. Formed and welded into integrated units with doors installed. 2. Body parts flanged and angled to provide rigidity; assembled by welding, bolting, or riveting using corrosion-resistant bolts and aluminum or stainless steel rivets. 3. Provide mounting holes for attaching lockers back-to-back and side-by-side.

D. Internal Components: 1. Shelves: [Stainless] steel. a. Two small and two large shelves. b. One small shelf with lockable valuables compartment. 2. Coat bar. 3. Perforated [stainless] steel boot tray. 4. Double hook for storage. 5. Single coat hooks on each side panel. 6. Pegboard panels on inside of doors, with storage pocket. 7. Unbreakable mirror with magnetic attachment. 8. Knockouts for electrical conduit; verify location in field.

E. Drawer Unit: 1. Located under locker unit. 2. Width to match locker x [24] [36] inches deep x [15] [18] inches high. 3. 200 pound capacity drawer slides. 4. Integrally formed ventilated handles. 5. Keyless lock; locks when locker door is closed. Released by pull handle inside locker.

F. Body Armor Drying Rack: Perforated [stainless] steel.

G. Bench: Hardwood, attached to top of drawer unit at each locker.

Metal Vented Wardrobe Lockers 10 5113-2 Tiffin Metal Products 08/19/10 H. Door Locks and Latches: 1. Lift latch operated, top and bottom bayonet style permitting closing without lifting latch handle. 2. Recessed door latch, painted cup with integral door latch/pull, pry-resistant, not protruding beyond face of door. 3. Locks: [Combination locks with master key override; furnish [one] [____] master [key.] [keys.]] [Key cylinder with locking cam; furnish [one key] [[____] keys] per lock and [one master key.] [[____] master keys.] Key as directed by Owner.] [Padlock hasp.]

I. Number Plates: 1. Number plates furnished loose and affixed to locker using pop rivets in pre-drilled holes in door. 2. Number doors as directed by Owner. J. Accessories: 1. Continuous sloping tops, minimum 24 gauge [stainless] steel. 2. Finished end panels without exposed fasteners. 3. Filler panels. 4. 4 inch high, four-sided base, ventilated, minimum 16 gauge [stainless] steel.

2.4 FINISHES

A. Steel: 1. Minimum 5 mil thick factory-applied baked-on textured powder coat finish. 2. Color: [Custom] [____] color [to be selected from manufacturer's full color range].

**** OR ****

B. Stainless Steel: 1. Face frame: No. 3 satin. 2. Doors: Patterned. 3. Body: No. 2B.

PART 3 EXECUTION

3.1 INSTALLATION

A. Install in accordance with manufacturer's instructions and approved Shop Drawings.

B. Set plumb, level, and aligned.

C. Attach lockers to supporting construction with anchors best suited to substrate conditions.

D. Bolt adjacent locker units together to provide rigid installation.

E. Install [end panels] [filler panels] [and] [sloped tops].

3.2 ADJUSTING

A. Adjust doors and latches to operate correctly.

END OF SECTION

Tiffin Metal Products 10 5113-3 Metal Vented Wardrobe Lockers 08/19/10