Display Hidden Notes to Specifier. (Don't Know How? Click Here) s80

SECTION 08810 GLASS

Display hidden notes to specifier. (Don't know how? Click Here)

PART 1 GENERAL

1.1 SECTION INCLUDES

1.A. Fabrication of extra-large glass constructions.

1.2 RELATED SECTIONS

2.A. Section 08800 - Glazing: Application, installation and installation accessories.

1.3 REFERENCES

3.A. ANSI Z97.1 - American National Standard for Glazing Materials Used in Buildings, Safety Performance Specifications and Methods of Test.

3.B. ASTM International (ASTM): 3.B.1. ASTM C162 - Standard Terminology of Glass and Glass Products. 3.B.2. ASTM C1036 - Standard Specifications for Flat Glass. 3.B.3. ASTM C1172 - Standard Specification for Laminated Architectural Flat Glass. 3.B.4. ASTM C1048 - Standard Specification for Heat-Treated Glass - Kind HS, Kind FT, Coated and Uncoated Glass. 3.B.5. ASTM C1376 - Standard Specification for Pyrolytic and Vacuum Deposition Coatings on Glass. 3.B.6. ASTM E1300 - Standard Practice for Determining Minimum Thickness and Type of Glass required to resist a specific load. 3.B.7. ASTM E773 - Standard Test Method for Seal Durability of Sealed Insulating Glass Units. 3.B.8. ASTM E774 - Standard Specification for Sealed Insulating Glass Units. 3.B.9. ASTM E2188 - Standard Test Method for Insulating Glass Unit Performance. 3.B.10. ASTM E2189 - Standard Test Method for Testing Resistance to Fogging in Insulating Glass Units. 3.B.11. ASTM E2190 - Standard Specification for Insulating Glass Unit Performance and 08810-1 Evaluation.

3.C. Canadian General Standards Board (CAN/CGSB): 3.C.1. CAN/CGSB 12.1 M90 - Tempered or Laminated Safety Glass. 3.C.2. CAN/CGSB 12.2 M90 - Flat, Clear Sheet Glass. 3.C.3. CAN/CGSB 12.3 M90 - Flat, Clear Sheet Glass. 3.C.4. CAN/CGSB 12.4 M90 - Flat, Heat Absorbing Glass. 3.C.5. CAN/CGSB 12.8 M90 - Insulating Glass Units. 3.C.6. CAN/CGSB 12.10 M90 - Light and Heat Reflecting Glass.

3.D. CPSC 16 CFR 1201 - Safety Standard for Architectural Glazing Materials.

1.4 SUBMITTALS

4.A. Submit under provisions of Section 01300.

4.B. Product Data: For each glass product and glazing material indicated.

4.C. Product Certificates: For glass and glazing products, from manufacturer.

4.D. Warranties: Sample of special warranties.

4.E. Selection Samples: For each finish product specified, two complete sets of color chips representing manufacturer's full range of available colors and patterns.

4.F. Verification Samples: For each finish product specified, two samples, minimum size 6 inches (150 mm) square representing actual product, color, and patterns.

1.5 QUALITY ASSURANCE

5.A. Manufacturer Qualifications: Minimum 5 year experience manufacturing similar products.

5.B. Insulating-Glass Certification Program: Permanently marked either on spacers or on at least one component lite of units with appropriate certification label of IGCC.

5.C. Source Limitations for Glass: Obtain insulating glass from single source from single manufacturer for each glass type and technology.

5.D. Mockups: Build mockups to demonstrate aesthetic effects and to set quality standards for materials and execution. 5.D.1. Install glazing in mockups specified in Section 088000 to match glazing systems required for Project, including glazing methods.

08810-2 1.6 PRE-INSTALLATION MEETINGS

6.A. Convene minimum two weeks prior to starting work of this section.

1.7 DELIVERY, STORAGE, AND HANDLING

7.A. Deliver and store products in manufacturer's unopened packaging bearing the brand name and manufacturer's identification until ready for installation.

7.B. Protect glazing materials according to manufacturer's written instructions. Prevent damage to glass and glazing materials from condensation, temperature changes, direct exposure to sun, or other causes.

7.C. Handling: Handle materials to avoid damage.

1.8 WARRANTY

8.A. Manufacturer's Special Warranty for Coated-Glass Products: Manufacturer agrees to replace coated-glass units that deteriorate within specified warranty period. Deterioration of coated glass is defined as defects developed from normal use that are not attributed to glass breakage or to maintaining and cleaning coated glass contrary to manufacturer's written instructions. Defects include peeling, cracking, and other indications of deterioration in coating. 8.A.1. Warranty Period: Ten years from date of shipment from manufacturer.

8.B. Manufacturer's Special Warranty for Laminated Glass: Manufacturer agrees to replace laminated-glass units that deteriorate within specified warranty period. Deterioration of laminated glass is defined as defects developed from normal use that are not attributed to glass breakage or to maintaining and cleaning laminated glass contrary to manufacturer's written instructions. Defects include edge separation, delamination materially obstructing vision through glass, and blemishes exceeding those allowed by referenced laminated-glass standard. 8.B.1. Warranty Period: Five years from date of shipment from manufacturer.

8.C. Manufacturer's Special Warranty for Insulating Glass: Manufacturer agrees to replace insulating-glass units that deteriorate within specified warranty period. Deterioration of insulating glass is defined as failure of hermetic seal under normal use that is not attributed to glass breakage or to maintaining and cleaning insulating glass contrary to manufacturer's written instructions. Evidence of failure is the obstruction of vision by dust, moisture, or film on interior surfaces of glass. 8.C.1. Warranty Period: Ten years from date of shipment from manufacturer, except five years from date of shipment for units over 65 square feet or over 96 by 96 inches.

PART 2 PRODUCTS

2.1 MANUFACTURERS

1.A. Acceptable Manufacturer: AGNORA, which is located at: 200 Mountain Rd.; Collingwood, ON, Canada L9Y 4V5; Tel: 705-444-6654; Fax: 705-444-6657; Email: request info 08810-3 ([email protected]); Web: www.BIGASSGLASS.com

1.B. Web: http://www.bigassglass.com.

1.C. Substitutions: Not permitted.

1.D. Requests for substitutions will be considered in accordance with provisions of Section 01600.

2.2 APPLICATIONS/SCOPE CAPABILITY

2.A. Process: CNC Machining. 2.A.1. Thickness: 5 - 50 mm (3/16 inch - 2 inches). 2.A.2. Maximum Size: 3.3 x 6.1 m (130 x 240 inches).

2.B. Process: Straight Edge Polishing. 2.B.1. Thickness: 5 - 100 mm (3/16 inch - 4 inches). 2.B.2. Maximum Size: 3.3 x 7.6 m (130 x 300 inches).

2.C. Process: Painting. 2.C.1. Thickness: 5 - 25 mm (3/16 inch - 1 inch). 2.C.2. Maximum Size: 2.3 x 7.0 m (84 x 275 inches).

2.D. Process: Tempering. 2.D.1. Thickness: 5 - 25 mm (3/16 inch - 1 inch). 2.D.2. Maximum Size: 3.3 x 7.0 m (130 x 275 inches).

2.E. Process: Heat Strengthening. 2.E.1. Thickness: 5 - 12 mm (3/16 inch -1/2 inch). 2.E.2. Maximum Size: 3.3 x 7.0 m (130 x 275 inches).

2.F. Process: Heat Soak Testing. 2.F.1. Thickness: 5 - 25 mm (3/16 inch - 1 inch). 2.F.2. Maximum Size: 3.3 x 7.0 m (130 x 283 inches).

2.G. Process: Laminating. 2.G.1. Thickness: 6 - 100 mm (1/4 inch- 4 inches). 2.G.2. Maximum Size: 3.3 x 7.6 m (130 x 300 inches).

08810-4 2.H. Process: Insulating. 2.H.1. Thickness: 12 - 90 mm (1/2 inch - 3-1/2 inches). 2.H.2. Maximum Size: 3.3 x 6.1 m (130 x 240 inches).

2.3 MATERIALS

3.A. Licensed materials for glass fabrications. 3.A.1. Company: Saint-Gobain Glass. 3.A.2. Company: Pilkington Glass. 3.A.3. Company: PPG Industries. 3.A.4. Company: Saflex/Vanceva. 3.A.5. Company: Dupont/SentryGlas. 3.A.6. Company: ICD.

2.4 GLASS PRODUCTS

4.A. Clear Annealed Float Glass: ASTM C 1036, Type I, Class 1 (clear), Quality-Q3.

4.B. Ultraclear Float Glass: ASTM C 1036, Type I, Class I (clear), Quality-Q3; and with visible light transmission of not less than 91 percent. 4.B.1. With solar heat gain coefficient of not less than 0.87.

4.C. Tinted Annealed Float Glass: ASTM C 1036, Type I, Class 2 (tinted), Quality-Q3.

4.D. Fully Tempered Float Glass: ASTM C 1048, Kind FT (fully tempered), Condition A (uncoated) unless otherwise indicated, Type I, Class 1 (clear) or Class 2 (tinted) as indicated, Quality-Q3. 4.D.1. Fabrication Process: By horizontal (roller-hearth) process with roll-wave distortion parallel to bottom edge of glass as installed unless otherwise indicated.

4.E. Heat-Strengthened Float Glass: ASTM C 1048, Kind HS (heat strengthened), Type I, Condition A (uncoated) unless otherwise indicated, Type I, Class 1 (clear) or Class 2 (tinted) as indicated, Quality-Q3. 4.E.1. Fabrication Process: By horizontal (roller-hearth) process with roll-wave distortion parallel to bottom edge of glass as installed unless otherwise indicated.

4.F. Pyrolytic-Coated, Low-Maintenance Glass: Clear float glass with a coating on first surface having both photocatalytic and hydrophilic properties that act to loosen dirt and to cause water to sheet evenly over the glass instead of beading.

4.G. Ceramic-Coated Vision Glass: ASTM C 1048, Condition C, Type I, Class 1 (clear) or Class 2 (tinted) as indicated, Quality-Q3; and complying with Specification No. 95-1-31 in GANA's 08810-5 "Engineering Standards Manual."

4.H. Reflective-Coated Vision Glass: ASTM C 1376.

4.I. Ceramic-Coated Spandrel Glass: ASTM C 1048, Type I, Condition B, Quality-Q3.

4.J. Silicone-Coated Spandrel Glass: ASTM C 1048, Type I, Condition C, Quality-Q3.

4.K. Reflective-Coated Spandrel Glass: ASTM C 1376, Kind CS.

4.L. Safety Glazing Labeling: Where safety glazing is indicated, permanently mark glazing with certification label of the SGCC or another certification agency acceptable to authorities having jurisdiction. Label shall indicate manufacturer's name, type of glass, thickness, and safety glazing standard with which glass complies.

4.M. Heat-Treated Float Glass: ASTM C 1048; Type I; Quality-Q3; Class I (clear) unless otherwise indicated; of kind and condition indicated. 4.M.1. Fabrication Process: By horizontal (roller-hearth) process with roll-wave distortion parallel to bottom edge of glass as installed unless otherwise indicated.

2.5 CNC MACHINING

5.A. Heat Treated Glass Products - Fabrication Guidelines: 5.A.1. Hole to Glass Edge Location: The minimum distance from the rim of a hole to the nearest edge of the glass shall be 1/4 inch (6 mm) or twice the glass thickness, whichever is greater. Tolerance for location of hole from specified edge is plus or minus 1/16 inch (1.5 mm). 5.A.2. Hole to Hole Location: The minimum distance between the rims of adjacent holes shall be 3/8 inch (9.5 mm) or 2 x glass thickness, whichever is greater. Tolerance for dimension between hole centers is plus or minus 1/16 inch (1.5 mm). 5.A.3. Hole to Corner Location: Holes in the vicinity of a corner shall be positioned so that the nearest edge of the hole is a minimum distance from the corner of 6.5 x the glass thickness. 5.A.4. Minimum Hole Diameter and Notch Radius: Circular holes shall have a diameter no less than 1/4 inch (6 mm) or equal to the glass thickness, whichever is greater. 5.A.5. Notches and cutouts shall have a radius corner greater than the glass thickness. Tolerance of hole diameter is ± 1/16 inch (1.5 mm). Dimensional tolerances of notches and cutouts is ± 1/16 inch (1.5 mm) for glass thicknesses less than 1/2 inch and plus or minus 1/8 inch (3 mm) for glass thicknesses of 1/2 inch (13 mm) or greater.

2.6 EDGE POLISHING

6.A. Code: BMCNCG. 6.A.1. Name: CNC ground back mitre. 6.A.2. 08810-6 Description: Variable angle ground mitre. Glass is removed on the back surface.

6.B. Code: BMCNCP. 6.B.1. Name: CNC high polish back mitre. 6.B.2. Description: Variable angle polish mitre. Glass is removed on the back surface. Use of cerium wheel.

6.C. Code: BMCNHP. 6.C.1. Name: CNC high polish back mitre. 6.C.2. Description: Variable angle polish mitre. Glass is removed on the back surface. Use of cerium wheel.

6.D. Code: BMDTGR. 6.D.1. Name: Diamond tool ground back mitre. 6.D.2. Description: Variable angle ground mitre. Glass is removed on the back surface.

6.E. Code: BMDTHP. 6.E.1. Name: Diamond high polish Back mitre 6.E.2. Description: Variable angle polish mitre. Glass is removed on the back surface. Use of cerium wheel.

6.F. Code: FLAKSR. 6.F.1. Name: Belt edge arris. 6.F.2. Description: Diamond belt arrissed.

6.G. Code: FLASYM 6.G.1. Name: Asymmetrical chamfer CNC polish. 6.G.2. Description: Used for tempered laminates. Initial CNC polish to size and shape followed by diamond high polish on straight-line single edger.

6.H. Code: FLCNCG 6.H.1. Name: CNC flat ground. 6.H.2. Description: Dull edge with a chamfer on each side.

6.I. Code: FLCNCP 6.I.1. Name: CNC polish. 6.I.2. Description: Shiny edge with lines parallel to surfaces and chamfers on each side.

6.J. 08810-7 Code: FLCNHP. 6.J.1. Name: CNC high polish. 6.J.2. Description: Dull edge with a chamfer on each side.

6.K. Code: FLDTHP. 6.K.1. Name: Diamond high polish. 6.K.2. Description: Shiny edge with a chamfer on each side.

6.L. Code: FLGKSR. 6.L.1. Name: Belt flat ground. 6.L.2. Description: Diamond Belt flat ground. Some spots remain "as cut".

6.M. Code: FMCNCG. 6.M.1. Name: CNC ground front mitre. 6.M.2. Description: Variable angle ground mitre. Glass is removed on the front surface.

6.N. Code: FMCNCP. 6.N.1. Name: CNC polish front mitre. 6.N.2. Description: Variable angle polish mitre. Glass is removed on the front surface.

6.O. Code: FMCNHP. 6.O.1. Name: CNC high polish front mitre 6.O.2. Description: Variable angle polish mitre. Glass is removed on the front surface. Use of cerium wheel.

6.P. Code: FMDTGR. 6.P.1. Name: Diamond tool ground front mitre. 6.P.2. Description: Variable angle ground mitre made on single edger. Glass is removed on the front surface.

6.Q. Code: FMDTHP 6.Q.1. Name: Diamond high polish mitre. 6.Q.2. Description: Variable angle polish mitre made on single edger. Glass is removed on the back surface.

2.7 TEMPERING/HEAT STRENGTHENING

7.A. Strength: Where annealed float glass is indicated, provide annealed float glass, heat- 08810-8 strengthened float glass, or fully tempered float glass as needed to comply with "Performance Requirements" Article. Where heat-strengthened float glass is indicated, provide heat- strengthened float glass or fully tempered float glass as needed to comply with "Performance Requirements" Article. Where fully tempered float glass is indicated, provide fully tempered float glass.

2.8 LAMINATED GLASS

8.A. Laminated Glass: ASTM C 1172. Use materials that have a proven record of no tendency to bubble, discolor, or lose physical and mechanical properties after fabrication and installation. 8.A.1. Construction: comply with interlayer manufacturer's written instructions. 8.A.1.a. DuPont SentryGlas Clear. 8.A.1.b. Eastman (Solutia) Saflex Standard Color. 8.A.1.c. Eastman (Solutia) Vanceva Foundation Color. 8.A.1.d. Eastman (Solutia) Vanceva Specialty Color. 8.A.1.e. Eastman (Solutia) Vanceva White. 8.A.1.f. Eastman (Solutia) Vanceva Black. 8.A.1.g. Eastman (Solutia) Vanceva Hurricane Storm. 8.A.1.h. Eastman (Solutia) Saflex Acoustic Clear. 8.A.1.i. Southwall XIR 72-41. 8.A.1.j. Trosifol Clear.

2.9 INSULATING GLASS

9.A. Manufacturers: Subject to compliance with requirements, provide glass technology as licensed and fabricated by AGNORA with identical performance characteristics: Manufacturers of licensed products shall be as listed below: 9.A.1. Company: Saint-Gobain Glass. 9.A.2. Company: Pilkington Glass. 9.A.3. Company: PPG Industries. 9.A.4. Company: Saflex/Vanceva. 9.A.5. Company: Dupont/SentryGlas. 9.A.6. Company: ICD.

9.B. Thermal and Optical Performance Properties: Provide glass with performance properties specified, as indicated in manufacturer's published test data, based on procedures indicated below: 9.B.1. For insulating-glass units, properties are based on units of thickness indicated for overall unit and for each lite.

08810-9 9.B.2. U-Factors: Center-of-glazing values, according to NFRC 100 and based on LBL's WINDOW 5.2 computer program, expressed as Btu/sq. ft. x h x deg F. 9.B.3. Solar Heat-Gain Coefficient and Visible Transmittance: Center-of-glazing values, according to NFRC 200 and based on LBL's WINDOW 5.2 computer program. 9.B.4. Visible Reflectance: Center-of-glazing values, according to NFRC 300.

9.C. Insulating-Glass Units: Factory-assembled units consisting of sealed lites of glass separated by a dehydrated interspace, qualified according to ASTM E 2190, and complying with other requirements specified. 9.C.1. Sealing System: _____. 9.C.2. Spacer: _____.

9.D. Glass Type GL-#: _____. 9.D.1. ______.

9.E. Construction: 9.E.1. ______.

9.F. Performance: 9.F.1. Overall Unit Thickness: _____ mm. 9.F.2. Thickness of Each Glass Lite: _____ mm. 9.F.3. Outdoor Lite: _____. 9.F.4. Interspace Content: _____. 9.F.5. Indoor Lite: Heat-strengthened float glass. 9.F.6. Low-E Coating: _____. 9.F.7. Reflectance - Visible In: _____ percent. 9.F.8. Reflectance - Visible Out: _____ percent. 9.F.9. Visible Light Transmittance: _____ percent minimum. 9.F.10. Winter Nighttime U-Factor: _____ maximum. 9.F.11. Summer Daytime U-Factor: _____ maximum. 9.F.12. Solar Heat Gain Coefficient: _____ maximum. 9.F.13. Shading Coefficient: _____.

2.10 SPANDREL GLASS

10.A. Glass Type GL-#: Spandrel Glass

08810-10 10.A.1. Ceramic-coated spandrel glass; 10.A.2. Silicone-coated spandrel glass. 10.A.3. Reflective-coated spandrel glass; Pyrolytic process 10.A.4. Reflective-coated spandrel glass; Sputter-coating (vacuum deposition process). 10.A.5. Heat-strengthened 10.A.6. Fully tempered float glass. 10.A.7. Basis-of-Design Product: _____. 10.A.8. Glass: _____. 10.A.9. Tint Color: _____. 10.A.10. Coating Color: _____. 10.A.11. Minimum Thickness: _____. 10.A.12. Coating Location: _____. 10.A.13. Winter Nighttime U-Factor: _____. 10.A.14. Summer Daytime U-Factor: _____. 10.A.15. Fallout Resistance: Passes fallout-resistance test in ASTM C 1048 for an assembly of glass and adhered reinforcing material.

PART 3 EXECUTION

3.1 EXAMINATION

1.A. Examine glass and framing, with glazier present, for compliance with the following: 1.A.1. Openings to receive glazing are plumb and square. 1.A.2. Manufacturing and installation tolerances, including those for size, squareness, offsets at corners. 1.A.3. Minimum required face or edge clearances. 1.A.4. Observable edge damage or face imperfections.

1.B. Clean glass, glazing channels and other framing members receiving glass immediately before glazing.

1.C. Remove coatings that are not firmly bonded to substrates.

1.D. Do not proceed with installation until unsatisfactory conditions have been corrected. Commencement of work signifies acceptance of substrate and installation conditions.

3.2 INSTALLATION, GENERAL 08810-11 2.A. Comply with referenced GANA glazing manual and instructions of manufacturers of glass, glazing sealants, and glazing compounds.

2.B. Install in proper relationship with adjacent materials.

3.3 CLEANING AND PROTECTION

3.A. Protect glass from contact with contaminating substances resulting from construction operations. Remove such substances by method approved by manufacturer.

END OF SECTION

08810-12