Wood Ultimate Sliding French Door, Sliding Patio Door

Section 08 14 73 Wood Ultimate Sliding French Door Wood Sliding Patio Door

A. Part 1 General

B. 1.1 Section Includes

C. Wood Ultimate Sliding French Door and frame complete with hardware, glazing, weather strip, insect screen, removable grille, grilles-between-the-glass, simulated divided lite, ADL, interior shades, raised/flat panels, jamb extension, and standard or specified anchors, trim, attachments, and accessories.

D. Wood Sliding Patio Door and frame complete with hardware, glazing, weather strip, insect screen, removable grille, grilles-between-the-glass, simulated divided lite, interior shades, jamb extension, and standard or specified anchors, trim, attachments, and accessories.

E. 1.2 Related Sections

A. Section 01 33 23 – Submittal Procedures: Shop Drawings, Product Data, and Samples

B. Section 01 62 00 – Product Options

C. Section 01 63 00 – Product Substitution Procedures

D. Section 01 65 00 – Product Delivery

E. Section 01 66 00 – Product Storage and Handling Requirements

F. Section 01 71 00 – Examination and Preparation

G. Section 01 73 00 - Execution

H. Section 01 74 00 – Cleaning and Waste Management

I. Section 01 75 00 – Starting and Adjusting

J. Section 01 76 00 – Protecting Installed Construction

K. Section 06 22 00 – Millwork: Wood trim other than furnished by door and frame manufacturer

L. Section 07 92 00 – Joint Sealants: Sill sealant and perimeter caulking

M. Section 08 71 00 – Door Hardware: Hardware other than furnished by door and frame manufacturer

F. Section 09 90 00 – Paints and Coatings: Paint and stain other than factory-applied finish

Doc. 64314 Rev. 12/18/2017 Section 08 14 73 ~ 1 ~ Wood Sliding French Door / Patio Door CHECK MARVIN ONLINE DOCS FOR LATEST VERSION Printed on: 4/6/2018 22:01 a4/p4 G. 1.3 References

A. American Society for Testing and Materials (ASTM):

1. E283: Standard Test Method for Rate of Air Leakage through Exterior Windows, Curtain Walls, and Doors

2. E330: Standard Test Method for Structural Performance of Exterior Windows, Curtain Walls, and Doors by Uniform Static Air Pressure Difference

3. E547: Standard Test Method for Water Penetration of Exterior Windows, Curtain Walls, and Doors by Cyclic

4. E2190: Specification for Sealed Insulated Glass Units

5. C1036: Standard Specification for Flat Glass

H. E 2112: Standard Practice for Installation of Exterior Windows, Doors and Skylights

B. American Architectural Manufacturer’s Association / Window and Door Manufacturer’s Association (AAMA / WDMA/CSA):

1. AAMA/WDMA/CSA 101/I.S.2/A440-05: Standard/Specification for windows, doors, and unit skylights

I. AAMA/WDMA/CSA 101/I.S.2/A440-08: North American Fenestration, Standard/Specification for windows, doors, and skylights

J. AAMA/WDMA/CSA 101/I.S.2/A440-11: NAFS - North American Fenestration, Standard/Specification for windows, doors, and skylights

C. WDMA I.S.4: Industry Standard for Water Repellant Preservative Treatment for Millwork

D. Window and Door Manufacturer’s Association (WDMA): 101/I.S.2 WDMA Hallmark Certification Program

E. Sealed Insulating Glass Manufacturer’s Association / Insulating Glass Certification Council (SIGMA/IGCC)

F. National Fenestration Rating Council (NFRC):

1. 101: Procedure for Determining Fenestration Product Thermal Properties

K. 200: Procedure for Determining Solar Heat Gain Coefficients at Normal Incidence

L. Window Covering Manufacturer’s Association

1. A100.1: Standard for safety of corded window covering products M. 1.4 System Description

A. Design and Performance Requirements: Wood Ultimate Sliding French Door

Overall Overall Air Water Structural Design Certification Width Height # of Product Tested Tested Tested Pressure Rating Panels to psf to psf to psf (DP) in mm in mm

Wood Ultimate Sliding French 6.24 6.0 psf 52.5 LC-PG35-SD 35 191 (4851) 95 1/2 (2426) 4 Door 16080 (OXXO) Wood Ultimate Sliding French 1.57 6.0 psf 60 psf LC-PG40-SD 40 146 ( 3708) 95 1/2 (2426) 3 Door 12080 (OXO) Wood Ultimate Sliding French 146 1.57 6.0 psf 60 psf LC-PG40-SD 40 (3727) 95 1/2 (2426) 3 Door 12080 3/4 (OXO) Low Profile Sill Wood Ultimate Sliding French 1.57 6.0 psf 60 psf CW-PG40-FD 40 50 3/4 (1289) 95 1/2 (2426) 1 Door 4080 (O) (SLT) Wood Sliding Patio Door

Overall Overall # of Air Water Structural Design Certification Width Height Panels Product Tested Tested Tested Pressure Rating to psf to psf to psf (DP) in mm in mm

Wood Sliding Patio Door 1.57 3.75 psf 37.5 psf LC-PG25-SD 25 143 (3632) 95 1/2 (2426) 4 12080 (OXXO) Wood Sliding Patio Door 1.57 3.75 psf 37.5 psf LC-PG25-SD 25 191 (4851) 82 (2083) 4 16068 (OXXO)

Wood Sliding Patio Door 146 1.57 4.5 psf 45 psf LC-PG30-SD 30 (3726) 95 1/2 (2426) 3 12080 11/16 (XOO)

Wood Sliding Patio Door 1.57 6.0 psf 60 psf LC-PG40-SD 40 96 5/8 (2454) 82 (2083) 2 8068 (XO/OX) Wood Sliding Patio Door 16068 1.57 3.75 psf 37.5 psf LC-PG25-SD 25 191 (4851) 82 2083 4 (OXXO) Low Profile Sill Wood Sliding Patio Door 8068 1.57 6.0 psf 60 psf LC-PG40-SD 40 96 5/8 (2454) 82 2083 2 (XO/OX) Low Profile Sill

Doc. 64314 Rev. 12/18/2014 Section 08 14 73 ~ 3 ~ Wood Sliding French Door / Patio Door CHECK MARVIN ONLINE DOCS FOR LATEST VERSION Printed on: 4/6/2018 22:01 a4/p4 N. 1.5 Submittals

A. Shop Drawings: Submit shop drawings under provision of Section 01 33 23

B. Product Data: Submit catalog data under provision of Section 01 33 23

C. Samples:

1. Submit corner section under provision of section 01 33 23

2. Include glazing system, quality of construction and specified finish

D. Quality Control Submittals: Certificates: submit manufacturer’s certification indicating compliance with specified performance and design requirement under provision of section 01 33 23

O. 1.6 Quality Assurance

A. Requirements: Consult local code for IBC [International Building Code] and IRC [International Residential Code] adoption year and pertinent revisions

P. 1.7 Delivery

A. Comply with provisions of Section 01 65 00

B. Deliver in original packaging and protect from weather

Q. 1.8 Storage and Handling

A. Prime and seal wood surfaces, including to be concealed by wall construction, if more than thirty (30) days will expire between delivery and installation. Seal unfinished top and bottom edges of door panels if door panels are stored at the job site more than one (1) week.

B. Store door panel flat on a level surface in a clean and dry storage area above ground to protect from weather under provision of Section 01660

R. Condition doors to local average humidity before hanging

S. 1.9 Warranty

T. Complete and current warranty information is available at marvin.com/warranty. The following summary is subject to the terms, condition, limitations and exclusions set forth in the Marvin Windows and Door Limited Warranty and Products in Coastal Environments Limited Warranty Supplement: A. Clear insulating glass with stainless steel spacers is warranted against seal failure caused by manufacturing defects and resulting in visible obstruction through the glass for twenty (20) years from the original date of purchase. Glass is warranted against stress cracks caused by manufacturing defects from ten (10) years from the original date of purchase.

U. Factory applied interior finish is warranted to be free from finish defects for a period of five (5) years from the original date of purchase.

V. Hardware and other non-glass components are warranted to be free from manufacturing defects for ten (10) years from the original date of purchase.

W. Part 2 Products

X. 2.1 Manufactured Units

A. Description: Factory-assembled Wood Ultimate Sliding French Door(s), as manufactured by Marvin Windows and Doors, Ripley, Tennessee.

B. Description: Factory-assembled Wood Sliding Patio Door(s), as manufactured by Marvin Windows and Doors, Ripley, Tennessee.

Y. 2.2 Frame Description

A. Non Finger-Jointed Pine or finger-jointed core with non finger-jointed Pine veneer; non finger-jointed Mahogany or finger-jointed core with non finger-jointed Mahogany veneer; non finger-jointed Vertical Grain Douglas Fir or finger-jointed with non finger-jointed Vertical Grain Douglas Fir veneer.

1. Kiln-dried to moisture content no greater than twelve (12) percent at time of fabrication

2. Water repellant, preservative treated in accordance with WDMA I.S.4.

B. Frame width: 4 9/16” (116mm); 6 9/16” (167mm)

C. Frame thickness: 1 1/16” (27mm)

D. Beige or Bronze fiberglass reinforced plastic (frp) sill 0.115” (3.0mm) thick, with a polycarbonate thermoplastic roller track. Red Oak, Mahogany or Cherry interior sill liner.

1. Optional Beige or Bronze fiberglass reinforced plastic Low Profile Sill, 0.080 (2mm) thick, 1 ½” (38mm) drop down profile under screen track with a polycarbonate thermoplastic roller track. ADA complaint. Does not meet impact (IZ3) requirements.

Z. Optional flat oak interior sill with polycarbonate thermoplastic roller track. This will decrease the RO height by 7/8” (22mm)

AA.2.3 Panel Description

Doc. 64314 Rev. 12/18/2014 Section 08 14 73 ~ 5 ~ Wood Sliding French Door / Patio Door CHECK MARVIN ONLINE DOCS FOR LATEST VERSION Printed on: 4/6/2018 22:01 a4/p4 A. Laminated veneer lumber (LVL) cores with non finger-jointed Pine, Mahogany, Vertical Grain Douglas Fir veneer

1. Kiln-dried to moisture content no greater than twelve (12) percent at time of fabrication

2. Water repellant, preservative treated in accordance with WDMA I.S.4.

B. Panel thickness: 1 ¾” (44mm)

C. Sticking: Ogee is standard with optional square sticking

D. Top rail and stile width: 4 ¾” (121mm) for Sliding French Door, 3” (76mm) for Sliding Patio Door

E. Bottom rail height: Sliding French Door - 8 1/8” (206mm), edge glued; 9 1/8” (232mm) for Sliding French with low profile sill; Sliding Patio Door – 3” (76mm) with standard sill, 3 15/16” (100mm) for Sliding Patio with low profile sill, face laminated

AB. Panel corners glued and fastened with 5/8” x 4 inch (16mm by 102mm) fluted hardwood dowels. Removable interior vinyl glazing stops with non finger-jointed wood covers. No visible fasteners.

AC. 2.4 Glazing

A. Select quality complying with ASTM C 1036. Shall comply with 16 CFR 1201 Safety Standard for Architectural Glazing Materials.

B. Glazing Method: Tempered Insulating glass

C. Glass Type: Clear, Bronze, Gray, Reflective Bronze, Tempered, Obscure, Laminated, Low E2 with or without Argon, Low E3 with or without Argon, Low E1 with or without Argon

D. Glazing Seal: Silicone bedding, exterior

AD. 2.5 Finish

A. Interior/Exterior: Treated bare wood

1. Prime: Factory-applied enamel primer. Available on Pine product only

B. Interior Finish Options:

1. Painted Interior Finish. Available on Pine product only.

2. Factory-applied water-borne acrylic enamel clear coat. Applied in two separate coats with light sanding between coats. Available on Pine, Mahogany, Vertical Grain Douglas Fir

AE. Factory-applied water-borne urethane stain. Stain applied over a wood (stain) conditioner. A water- borne acrylic enamel clear coat applied in two separate coats, with light sanding coats, applied over the stain. Available on Pine, Mahogany, and Vertical Grain Douglas Fir. Colors available: Wheat, Honey, Hazelnut, Leather, Cabernet, or Espresso. AF. 2.6 Hardware

A. Handle Set: Zinc die-cast substrate

1. Powder Coat finishes: Satin Taupe (default)

a. Optional Powder Coat finishes: White or Dark Bronze

AG.Metal finishes (brass substrate): Brass PVD, Antique Brass, Oil Rubbed Bronze PVD, Oil Rubbed Bronze, Satin Chrome, Polished Chrome, and Satin Nickel PVD

B. Rollers: Two adjustable steel (steel) roller assemblies per operating panel

1. Two ball bearing wheels per roller assembly

2. Maximum vertical adjustment 5/16” (8mm)

3. Optional: stainless steel rollers

C. Sliding French Locking System:

1. Marvin exclusive multi-point 2 locking hooks, stainless steel mechanism and keepers. Locking system operated at handle assembly. (Key lock cylinder – for active handles)

AH. Optional: Three-point locking system with stainless steel keepers and mechanism. Manual head bolt is standard on inactive panel.

D. Sliding Patio Locking System:

1. 2 point lock, zinc plated steel mechanism and keeper. Locking system operated at handle assembly.

AI. Manual head bolt is standard on in-active panel

AJ. 2.7 Weather Strip

A. Interlock weather strip between sliding panel and meeting stile on stationary panel

B. Side jambs to have two sets of bulb weather strip maintaining contact with door panel

C. Continuous slip coat weather strip along sill, head jamb, and meeting stiles

AK. Color: Beige, optional black

AL. 2.8 Jamb Extension

A. Factory-applied up to 3” (76mm), for other wall thickness indicated or required (shipped loose)

B. Finish: Matches interior frame finish

AM. 2.9 Insect Screen

Doc. 64314 Rev. 12/18/2014 Section 08 14 73 ~ 7 ~ Wood Sliding French Door / Patio Door CHECK MARVIN ONLINE DOCS FOR LATEST VERSION Printed on: 4/6/2018 22:01 a4/p4 A. Standard Sliding Screen: Aluminum top hung sliding screen with adjustable rollers and replaceable bottom guide. Frame to have edge mounted wool pile bug strip.

1. Sliding screen for XO, OX, OOX, XOO, OXXO operation

AN. Screen mesh: Charcoal fiberglass or Hi-Tran fiberglass mesh

AO.Standard Sliding Screen available in Bahama Brown, Bronze, Evergreen, Pebble Gray, White.

B. Ultimate Sliding Screen: Extruded aluminum sliding top hung screen with stainless steel ball bearing in nylon wheels, top rollers adjustable up to ¼” (6mm). Replaceable bottom guide. Frame to have edge mounted wool pile bug strip.

2. Sliding screen for XO, OX, OOX, XOO, OXXO operation

AP. Screen mesh: Charcoal fiberglass, Charcoal aluminum wire, Black aluminum wire, Bright aluminum wire, Bright bronze wire, Hi-Tran fiberglass mesh

AQ.Colors: Pebble Gray, Bahama Brown, Evergreen, Bronze, Stone White, Ebony, Wineberry, Coconut Cream, Hampton Sage, Cashmere, Arctic White, Cumulus Gray, Desert Beige, Green, Sierra White, Cadet Gray, Cascade Blue, French Vanilla, Bright Silver (pearlescent), or Copper (pearlescent)

AR. 2.10 Removable Interior Grilles

A. 3/4” by 15/32” (19mm x 12mm) or 1 1/8” x 15/32” (29mm x 12mm) – Pine only

1. Pattern: Rectangular; custom lite layout

AS. Finish: Match interior panel finish

AT. 2.11 Simulated Divided Lites (SDL)

A. 5/8” (16mm), 7/8” (22mm) wide, 1 1/8” (29mm) wide, 1 15/16” (49mm), 2 13/32” (61mm) wide with or w/out internal spacer bar.

AU. Muntins: Pine, Mahogany, Vertical Grain Douglas Fir

AV. Muntins adhere to glass with double coated acrylic foam tape

AW.Sticking:

1. Standard: Ogee

AX. Optional: Square

AY. Pattern: Rectangular, cottage, custom lite layout

AZ. Finish: Match panel finish

BA.2.12 Grilles-Between-the–Glass (GBG) A. 23/32” (18mm) contoured aluminum bar.

1. Exterior Colors: Stone White. The use of different types of glazing may alter the exterior GBG color appearance.

2. Interior Color: Stone White is the default. Optional colors: Bronze, Pebble Gray, Sierra White, Ebony (only available with Ebony exterior).

BB. Optional flat aluminum spacer bar. Contact your Marvin representative.

BC. Pattern: Rectangular, cottage, custom lite layout

BD. 2.13 Authentic Divided Lites (ADL) – For Sliding French door only

A. 1 ½” (38mm) insulating Pine, Mahogany, Vertical Grain Douglas Fir muntins or 7/8” (22mm) single glaze ADL with energy panel.

1. Pattern: Rectangular; custom lite layout

2. Finish: Match sash finish

BE.2.14 Raised or Flat Panels (Sliding French Door only)

A. Extira® panel for wood exterior or interior. Constructed of medium density fiberboard (MDF) core with laminate veneer to interior and exterior. Available bare wood or selected interior finish.

BF. Utilizes 4 ¾” intermediate rail. Visible panel height is 12 1/64” (305mm).

BG. 2.15 Interior Shades

A. A cellular shade is attached to the door via a removable surround system that houses the cellular shade.

1. The shade moves independent of the door panels

BH. Shade stacks are hidden when the shades are open

BI. Operation is side to side

BJ. Pull Bar: Wood wrapped extruded aluminum

a. Species: Pine, Mahogany, Vertical Grain Douglas Fir, Mixed Grain Douglas Fir, Cherry, White Oak

BK. Interior Finishes: Matches interior panel finish

B. Cellular Shade

1. Single non-fire rated hexagonal honeycomb (cellular) 3/4” (19mm)

Doc. 64314 Rev. 12/18/2014 Section 08 14 73 ~ 9 ~ Wood Sliding French Door / Patio Door CHECK MARVIN ONLINE DOCS FOR LATEST VERSION Printed on: 4/6/2018 22:01 a4/p4 2. Semi-Opaque fabric (light filtering)

a. Colors: Driftwood, Marigold, Almond, Rose, Denim, Biscuit, Champagne, Moss, Cinnamon, Silver, White, Stone, Tan, Ivory, or Eggshell

3. Opaque fabric (blackout)

a. Colors: White, Stone, Tan, Ivory, or Eggshell

BL. 2.16 Accessories and Trim

A. Installation and Hardware Accessories:

1. Aluminum drip cap. Finish: Bahama Brown, Bronze, Evergreen, Pebble Gray, White.

2. Installation brackets: 6 3/8” (162mm), 9 3/8” (238mm), 15 3/8” (390mm)

3. Masonry brackets: 6” (152mm), 10” (254mm)

B. Exterior Wood Moulding:

1. Profile: Brick Mould Casing, Flat Casing, Stucco Brick Mould, Stucco Flat Casing, Special Casing 3 (SPC3), Special Casing 7 (SPC7), Special Casing 21 (SPC21), Special Casing 18 (SPC18), Special Casing 26 (SPC26)

2. Finish: Match exterior frame finish

BM.Cedar Dress:

1. Brick Mould and Flat Casing

2. Available on Pine frames

3. Bare Cedar

BN. Part 3 Execution

BO. 3.1 Examination

A. Verification of Condition: Before installation, verify openings are plumb, square and of proper dimensions as required in Section 01 71 00. Report frame defects or unsuitable conditions to the General contractor before proceeding.

B. Acceptance of Condition: Beginning on installation confirms acceptance of existing conditions.

BP. 3.2 Installation

A. Comply with Section 01 73 00. B. Assemble and install window/door unit(s) according to manufacturer’s instruction and reviewed shop drawing.

C. Install sealant and related backing materials at perimeter of unit or assembly in accordance with Section 07 92 00 Joint Sealants. Do not use expansive foam sealant.

D. Install accessory items as required.

E. Use finish nails to apply wood trim and mouldings.

BQ. 3.3 Field Quality Control

A. Remove visible labels and adhesive residue according to manufacturer’s instruction.

A. Unless otherwise specified, air leakage resistance tests shall be conducted at a uniform static pressure of 75 Pa (~1.57 psf). The maximum allowable rate of air leakage shall not exceed 2.3 L/sm2 (~0.45 cfm/ft2).

B. Unless otherwise specified, water penetration resistance testing shall be conducted per AAMA 502 and ASTM E1105 at 2/3 of the fenestration products design pressure (DP) rating using “Procedure B” – cyclic static air pressure difference. Water penetration shall be defined in accordance with the test method(s) applied.

BR. 3.4 Cleaning

A. Remove visible labels and adhesive residue according to manufacturer’s instruction.

B. Leave windows and glass in a clean condition. Final cleaning as required in Section 01 74 00.

BS.3.5 Protecting Installed Construction

A. Comply with Section 07 76 00.

B. Protecting windows from damage by chemicals, solvents, paint or other construction operations that may cause damage.

End of Section

Doc. 64314 Rev. 12/18/2014 Section 08 14 73 ~ 11 ~ Wood Sliding French Door / Patio Door CHECK MARVIN ONLINE DOCS FOR LATEST VERSION Printed on: 4/6/2018 22:01 a4/p4