Victorian Purchasing Guide for UEE11 Electrotechnology Version 1

Victorian Purchasing Guide for the

UEE11 Electrotechnology Training Package

Version No 1

September 2012 © State of Victoria (Department of Education and Early Childhood Development) 2012. Copyright of this material is reserved to the Crown in the right of the State of Victoria. This work is licensed under a Creative Commons Attribution-NoDerivs 3.0 Australia licence (http://creativecommons.org/licenses/by-nd/3.0/au/). You are free use, copy and distribute to anyone in its original form as long as you attribute Skills Victoria, Department of Education and Early Childhood Development as the author, and you license any derivative work you make available under the same licence.

Disclaimer In compiling the information contained in and accessed through this resource, the Department of Education and Early Childhood Development (DEECD) has used its best endeavours to ensure that the information is correct and current at the time of publication but takes no responsibility for any error, omission or defect therein. To the extent permitted by law DEECD, its employees, agents and consultants exclude all liability for any loss or damage (including indirect, special or consequential loss or damage) arising from the use of, or reliance on the information contained herein, whether caused or not by any negligent act or omission. If any law prohibits the exclusion of such liability, DEECD limits its liability to the extent permitted by law, for the resupply of the information.

Third party sites This resource may contain links to third party websites and resources. DEECD is not responsible for the condition or content of these sites or resources as they are not under its control. Third party material linked from this resource is subject to the copyright conditions of the third party. Users will need to consult the copyright notice of the third party sites for conditions of usage.

of 50 Victorian Purchasing Guide  Version History

Training Package Date VPG Comments Version Approve d UEE11 Version 1 21 Initial Release of the UEE11 Electrotechnology Training Septembe Package Version 1 r 2012

of 50 UEE11 Electrotechnology Training Package Victorian Purchasing Guide

CONTENTS

of 50 INTRODUCTION What is a Victorian Purchasing Guide?

The Victorian Purchasing Guide provides information for use by Registered Training Organisations (RTOs) in the provision of Victorian government subsidised training.

Specifically the Victorian Purchasing Guide provides the following information related to the delivery of nationally endorsed Training Packages in Victoria:  The nominal hour range (minimum-maximum) available for each qualification.  Nominal hours for each unit of competency within the Training Package.  Sample Training Programs

Registration

RTOs must be registered by either the Victorian Registration and Qualifications Authority (VRQA) or the Australian Skills Qualification Authority (ASQA) regulatory body to be eligible to issue qualifications and statements of attainment under the Australian Quality Framework (AQF).

The VRQA is the regulatory authority for Victoria that registers VET training organisations who provide courses to domestic students only and who only offer training in Victoria.

To register to provide training to international students and in other Australian states and territories you will need to apply with ASQA.

of 50 QUALIFICATIONS

of 50 Code Title Qualification Nominal Hour Range Minimum Maximum UEE10111 Certificate I in ElectroComms Skills 180 180 UEE20111 Certificate II in Split Air-conditioning 360 360 and Heat Pumps Systems UEE20411 Certificate II in Winding and 360 360 Assembly UEE20511 Certificate II in Computer Assembly 360 360 and Repair UEE20711 Certificate II in Data and Voice 420 420 Communications UEE20811 Certificate II in Electrical 380 380 Wholesaling UEE20911 Certificate II in Electronic Assembly 360 360 UEE21011 Certificate II in Fire Alarms Servicing 360 360 UEE21211 Certificate II in Antennae Equipment 360 360 UEE21311 Certificate II in Remote Area 360 360 Essential Service UEE21411 Certificate II in Remote Area Power 360 360 Supply Maintenance UEE21611 Certificate II in Security Assembly 360 360 and Set-up UEE21711 Certificate II in Technical Support 360 360 UEE21911 Certificate II in Electronics 360 360 UEE22011 Certificate II in Electrotechnology 380 380 (Career Start) UEE22111 Certificate II in Sustainable Energy 420 420 (Career Start) UEE30111 Certificate III in Business Equipment 1020 1020 UEE30211 Certificate III in Computer Systems 1020 1020 Equipment UEE30311 Certificate III in Custom Electronics 980 980 Installations UEE30411 Certificate III in Data and Voice 1020 1020 Communications UEE30611 Certificate III in Electrical Machine 1100 1100 Repair UEE30711 Certificate III in Switchgear and 1100 1100 Controlgear UEE30811 Certificate III in Electrotechnology 1100 1100 Electrician UEE30911 Certificate III in Electronics and 1020 1020 Communications UEE31011 Certificate III in Fire Protection 1020 1020 Control UEE31111 Certificate III in Gaming Electronics 1020 1020 UEE31211 Certificate III in Instrumentation and 1020 1020 Control UEE31411 Certificate III in Security Equipment 1020 1020 Code Title Qualification Nominal Hour Range

of 50 Page 8 of 50 UNITS OF COMPETENCY AND NOMINAL HOURS

RTOs are advised that there is a mapping inside the Training Package that describes the relationship between new units and superseded or replaced units from the previous version of UEE11 Electrotechnology Training Package. Information regarding transition arrangements can be obtained from the state or national VET Regulating Authority (see Contacts and Links section).

You must be sure that all training and assessment leading to qualifications or Statements of Attainment from the UEE11 Electrotechnolgy Training Package is conducted against the Training Package units of competency and complies with the requirements in the assessment guidelines.

Listing of the Units of Competency and Nominal Hours

Unit Code Unit Title Nominal Hours UEENEEA101A Assemble electronic components 40 UEENEEA102A Select electronic components for assembly 20 UEENEEA103A Set up and check electronic component assembly 40 machines UEENEEA104A Modify electronic sub assemblies 40 UEENEEA105A Conduct quality and functional tests on assembled 20 electronic apparatus UEENEEA106A Use lead-free soldering techniques 40 UEENEEA107A Make up wiring looms for internal wiring of appliances 40 and machinery UEENEEA110A Assemble, mount and connect control gear and 120 switchgear UEENEEA112A Fabricate and assemble bus bars 60 UEENEEA113A Mount and wire control panel equipment 60 UEENEEB101A Operate and maintain amateur radio communication 40 stations UEENEEC001B Maintain documentation 20 UEENEEC002B Source and purchase material/parts for installation or 20 service jobs UEENEEC003B Provide quotations for installation or service jobs 20 UEENEEC004B Prepare specifications for the supply of materials and 40 equipment for electrotechnology projects UEENEEC005B Estimate electrotechnology projects 40 UEENEEC006B Prepare tender submissions for electrotechnology 60 projects UEENEEC007B Manage contract variations 40 UEENEEC008B Receive and store materials and equipment for 20 electrotechnology work UEENEEC009B Provide quotations for inspection and compliance audit 40 services UEENEEC010B Deliver a service to customers 20 UEENEEC012B Direct technical and non-technical enquiries to 20 appropriate personnel UEENEEC013B Participate in business equipment work and 20

of 50 Unit Code Unit Title Nominal Hours competency development activities UEENEEC014B Participate in computer equipment work and 20 competency development activities UEENEEC016B Participate in voice and data communications work and 20 competency development activities UEENEEC017B Participate in appliance servicing work and 20 competency development activities UEENEEC018B Participate in electrical machine repair work and 20 competency development activities UEENEEC019B Participate in switchgear and controlgear work and 20 competency development activities UEENEEC020B Participate in electrical work and competency 20 development activities UEENEEC021B Participate in electronics and communications work 20 and competency development activities UEENEEC022B Participate in fire protection control work and 20 competency development activities UEENEEC023B Participate in gaming electronic work and competency 20 development activities UEENEEC024B Participate in instrumentation and control work and 20 competency development activities UEENEEC025B Participate in refrigeration and air conditioning work 20 and competency development activities UEENEEC026B Participate in security equipment work and competency 20 development activities UEENEEC027B Participate in rail communications and networks work 20 and competency development activities UEENEED101A Use computer applications relevant to a workplace 20 UEENEED102A Assemble, set-up and test computing devices 80 UEENEED103A Evaluate and modify object oriented code programs 40 UEENEED104A Use engineering applications software on personal 40 computers UEENEED110A Set up, create and implement content for a web server 120 UEENEED111A Develop, implement and test object oriented code 140 UEENEED112A Support computer hardware and software for 120 engineering applications UEENEED113A Install and administer Unix based networked 80 computers UEENEED114A Design and manage enterprise computer networks 80 UEENEED115A Administer computer networks 80 UEENEED116A Develop computer network services 120 UEENEED117A Install and configure network systems for 120 internetworking UEENEED118A Design and implement network systems for 120 internetworking UEENEED119A Design and implement advanced routing for 100 internetworking systems UEENEED120A Design and implement remote access for 100 Internetworking systems

of 50 Unit Code Unit Title Nominal Hours UEENEED121A Design and implement multi-layer switching for 100 Internetworking systems UEENEED122A Design and implement security for Internetworking 100 systems UEENEED123A Design and implement wireless LANs/WANs for 100 internetworking systems UEENEED124A Integrate multiple computer operating systems on a 80 client server local area network UEENEED129A Develop web pages for engineering applications 40 UEENEED130A Select, install, configure and test multimedia 40 components UEENEED143A Install and configure a client computer operating 40 system and software UEENEED144A Commission industrial computer systems 20 UEENEED145A Modify-redesign of industrial computer systems 20 UEENEED146A Set up and configure basic local area network (LAN) 40 UEENEED147A Develop energy sector directory services 80 UEENEED148A Plan industrial computer systems projects 60 UEENEED149A Develop energy sector computer network applications 80 infrastructure UEENEED150A Develop industrial control programs for microcomputer 60 equipped devices UEENEED151A Provide programming solution for computer systems 60 engineering problems UEENEED152A Design embedded controller control systems 80 UEENEED153A Set up, configure and test biometric devices 40 UEENEED154A Analyse and implement biometric measuring 120 techniques and applications UEENEED155A Develop and validate biometric equipment/systems 120 installation UEENEEE006B Apply methods to maintain currency of industry 20 developments UEENEEE009B Comply with scheduled and preventative maintenance 20 program processes UEENEEE011C Manage risk in electrotechnology activities 60 UEENEEE012B Manage electrotechnology projects 40 UEENEEE013B Plan electrotechnology projects 60 UEENEEE015B Develop design briefs for electrotechnology projects 40 UEENEEE020B Provide basic instruction in the use of 20 electrotechnology apparatus UEENEEE038B Participate in development and follow a personal 20 competency development plan UEENEEE070B Write specifications for computer systems engineering 40 projects UEENEEE071B Write specifications for electrical engineering projects 40 UEENEEE072B Write specifications for electronics and 40 communications engineering projects UEENEEE073B Write specifications for refrigeration and air 40 conditioning engineering projects

of 50 Unit Code Unit Title Nominal Hours UEENEEE074B Write specifications for renewable energy engineering 40 projects UEENEEE075B Write specifications for industrial electronics and 40 control projects UEENEEE077B Write specifications for automated systems projects 40 UEENEEE078B Contribute to risk management in electrotechnology 20 systems UEENEEE080A Apply industry and community standards to 20 engineering activities UEENEEE081A Apply material science to solving electrotechnology 60 engineering problems UEENEEE082A Apply physics to solving electrotechnology engineering 60 problems UEENEEE083A Establish and follow a competency development plan 20 in an electrotechnology engineering discipline UEENEEE084A Write specifications for electrotechnology engineering 40 projects UEENEEE101A Apply Occupational Health and Safety regulations, 20 codes and practices in the workplace UEENEEE102A Fabricate, assemble and dismantle utilities industry 40 components UEENEEE103A Solve problems in ELV single path circuits 40 UEENEEE104A Solve problems in d.c. circuits 80 UEENEEE105A Fix and secure electrotechnology equipment 20 UEENEEE107A Use drawings, diagrams, schedules, standards, codes 40 and specifications UEENEEE108A Lay wiring/cabling and terminate accessories for extra- 40 low voltage (ELV) circuits UEENEEE110A Develop and implement energy sector maintenance 60 programs UEENEEE114A Supervise and coordinate energy sector work activities 40 UEENEEE117A Implement and monitor energy sector OHS policies 20 and procedures UEENEEE118A Establish, maintain and evaluate energy sector OHS 60 systems UEENEEE119A Solve problems in multiple path extra low voltage 40 (ELV) a.c. circuits UEENEEE121A Plan an integrated cabling installation system 40 UEENEEE122A Carry out preparatory energy sector work activities 60 UEENEEE123A Solve basic problems electronic and digital equipment 80 and circuits UEENEEE124A Compile and produce an energy sector detailed report 60 UEENEEE125A Provide engineering solutions for problems in complex 60 multiple path circuit UEENEEE126A Provide solutions to basic engineering computational 60 problems UEENEEE127A Use advanced computational processes to provide 120 solutions to energy sector engineering problems UEENEEE128A Develop engineering solutions to photonic system 80

of 50 Unit Code Unit Title Nominal Hours problems UEENEEE129A Solve electrotechnical engineering problems 60 UEENEEE130A Provide solutions and report on routine 60 electrotechnology problems UEENEEE131A Solve problems in ELV circuits for non electrical 40 workers UEENEEE137A Document and apply measures to control OHS risks 20 associated with electrotechnology work UEENEEE141A Use of routine equipment/plant/technologies in an 60 energy sector environment UEENEEE142A Produce products for carrying out energy sector work 80 activities UEENEEE143A Produce routine tools/devices for carrying out energy 120 sector work activities UEENEEE144A Apply technologies and concepts to energy sector work 120 activities UEENEEE145A Apply computation when using 160 equipment/materials/concepts in an energy sector environment UEENEEE146A Identify effects of energy on machinery and materials 120 in an energy sector environment UEENEEE147A Identify building techniques, methods and materials 60 used in energy sector work activities UEENEEE148A Carry out routine work activities in an energy sector 40 environment UEENEEE149A Contribute to the operation of support plant and 120 equipment used in electricity supply industry UEENEEE150A Undertake computations in an energy sector 120 environment UEENEEE151A Transport apparatus, equipment and materials 60 UEENEEE152A Observe safety practices are followed in the vicinity of 20 isolated electrical cables UEENEEE160A Provide engineering solutions for uses of materials and 100 thermodynamic effects UEENEEE161A Analyse static and dynamic parameters of electrical 80 equipment UEENEEE162A Select drive components for electrical equipment 80 design UEENEEE163A Analyse materials for suitability in electrical equipment 80 UEENEEE164A Design electrical machine drives and production layout 80 plans UEENEEE179A Identify and select components, accessories and 20 materials for energy sector work activities UEENEEE185A Write work activity reports 20 UEENEEE190A Prepare engineering drawings using manual drafting 60 and CAD for electrotechnology/utilities applications UEENEEE191A Prepare electrotechnology/utilities drawings using 60 manual drafting and CAD equipment and software UEENEEE192A Produce detailed electrotechnology /utilities drawings 60

of 50 Unit Code Unit Title Nominal Hours using computer aided design equipment and software UEENEEF101A Install and connect cabling for direct access to 20 telecommunications service UEENEEF102A Install and maintain cabling for multiple access to 120 telecommunication services UEENEEF103A Install and maintain telecommunication cabling for 40 services in lifts UEENEEF104A Install and modify performance data communication 40 copper cabling UEENEEF105A Install and modify optical fibre performance data 40 communication cabling UEENEEF106A Solve problems in voice and data communications 40 circuits UEENEEF107A Set up and configure the wireless capabilities of 40 communications and data storage devices UEENEEF108A Select and arrange equipment for wireless 60 communication networks UEENEEF109A Install and connect data and voice communication 60 equipment UEENEEF110A Select and arrange data and voice equipment for local 120 area networks UEENEEF111A Test, report and rectify faults in data and voice 60 installations UEENEEF112A Install aerial telecommunication cables 40 UEENEEF113A Install underground communication cables 40 UEENEEF114A Set up and configure basic data communication 40 systems UEENEEF115A Assemble and connect telecommunication frames and 60 cabinets UEENEEG006A Solve problems in single and three phase low voltage 80 machines UEENEEG033A Solve problems in single and three phase low voltage 60 electrical apparatus and circuits UEENEEG063A Arrange circuits, control and protection for general 40 electrical installations UEENEEG076A Install and replace low voltage current transformer 20 metering UEENEEG101A Solve problems in electromagnetic devices and related 60 circuits UEENEEG102A Solve problems in low voltage a.c. circuits 80 UEENEEG103A Install low voltage wiring and accessories 20 UEENEEG104A Install appliances, switchgear and associated 20 accessories for low voltage electrical installations UEENEEG105A Verify compliance and functionality of low voltage 60 general electrical installations UEENEEG106A Terminate cables, cords and accessories for low 40 voltage circuits UEENEEG107A Select wiring systems and cables for low voltage 80 general electrical installations

of 50 Unit Code Unit Title Nominal Hours UEENEEG108A Trouble-shoot and repair faults in low voltage electrical 80 apparatus and circuits UEENEEG109A Develop and connect electrical control circuits 80 UEENEEG110A Find and repair faults in LV d.c. electrical apparatus 60 and circuits UEENEEG111A Carry out basic repairs to electrical components and 40 equipment UEENEEG113A Install and maintain emergency safety systems 60 UEENEEG116A Diagnose and rectify faults in traction lift systems 80 UEENEEG118A Maintain operation of electrical mining equipment and 60 systems UEENEEG119A Maintain operation of electrical marine equipment and 60 systems UEENEEG120A Select and arrange equipment for special LV electrical 60 installations UEENEEG121A Verify compliance and functionality of special LV 40 electrical installations UEENEEG122A Conduct compliance inspection of single phase LV 60 electrical installations UEENEEG123A Conduct compliance inspection of LV electrical 40 installations with demand exceeding 100 A per phase UEENEEG124A Conduct compliance inspection of special LV electrical 60 installations UEENEEG125A Plan electrical installations with a low voltage demand 40 up to 400 A per phase UEENEEG126A Install and maintain field power and distribution 40 systems with a low voltage demand up to 200 A per phase UEENEEG127A Design electrical installations with a low voltage 40 demand greater than 400 A per phase UEENEEG128A Plan low voltage switchboard and control panel layouts 40 UEENEEG129A Overhaul and repair major switchgear and controlgear 60 UEENEEG130A Design switchboards rated for high fault levels (greater 60 than 400 A) UEENEEG131A Evaluate performance of low voltage electrical 40 apparatus UEENEEG132A Carry out low voltage electrical field testing and report 60 findings UEENEEG143A Develop engineering solution for synchronous machine 60 and control problems UEENEEG144A Develop engineering solutions for d.c. machine and 60 control problems UEENEEG145A Develop engineering solutions for induction machine 60 and control problems UEENEEG149A Provide engineering solutions to problems in complex 60 polyphase power circuits UEENEEG150A Wind electrical coils 40 UEENEEG151A Place and connect electrical coils 40 UEENEEG152A Rewind single phase machines 120

of 50 Unit Code Unit Title Nominal Hours UEENEEG153A Rewind three phase low voltage induction machines 120 UEENEEG154A Rewind LV direct current machines 120 UEENEEG155A Rewind HV three phase induction machines rated for 60 voltages to 3.3 kV UEENEEG156A Rewind HV three phase induction machines rated for 60 voltages above 3.3 kV UEENEEG157A Conduct electrical tests on LV electrical machines 40 UEENEEG158A Conduct electrical tests on HV electrical machines 60 UEENEEG159A Conduct mechanical tests on electrical machines and 40 components UEENEEG160A Evaluate performance of LV electrical machines 40 UEENEEG161A Design and develop modifications to LV electrical 60 machines UEENEEG162A Set up and place LV electrical apparatus and 40 associated circuits into service UEENEEG164A Repair and maintain mechanical components of 60 electrical machines UEENEEG165A Maintain and service traction lifts systems and 40 equipment UEENEEG166A Install and maintain escalators, moving walks and 40 treadways UEENEEG167A Align and install traction lift equipment 40 UEENEEG168A Diagnose and rectify faults in complex lift systems 40 UEENEEG169A Manage large electrical projects 40 UEENEEG170A Plan large electrical projects 60 UEENEEG171A Install, set up and commission interval metering 20 UEENEEG172A Investigate and report on electrical incidents and 60 causes UEENEEG175A Develop compliance policies and plans to conduct a 80 electrical contracting business UEENEEG177A Select low voltage power factor correction equipment 40 UEENEEG179A Develop detailed electrical drawings 60 UEENEEG180A Develop detailed and complex drawings for electrical 80 systems using CAD systems UEENEEG181A Provide advice on effective and energy efficient lighting 40 products UEENEEG182A Supply effective and efficient lighting products for 20 domestic and small commercial applications UEENEEG183A Provide advice on the application of energy efficient 20 lighting for ambient and aesthetic effect UEENEEG184A Provide photometric data for illumination system 80 design UEENEEG185A Select effective and efficient light sources and 60 luminaires for given locations and designs UEENEEG186A Design effective and efficient lighting for residential and 60 commercial buildings UEENEEG187A Design effective and efficient lighting for public, open 60 and sports areas UEENEEG188A Prepare quotations for the supply of effective and 40

of 50 Unit Code Unit Title Nominal Hours efficient lighting products for lighting projects UEENEEG189A Install and maintain emergency lighting systems 60 UEENEEG197A Apply currency of safe working practices and 20 compliance verification of electrical installations UEENEEG198A Apply compliance requirements to all aspects of 20 electrical work UEENEEG199A Conduct compliance and functional verification of 40 electrical apparatus and existing circuits UEENEEH101A Repair basic computer equipment faults by 40 replacement of modules/sub-assemblies UEENEEH102A Repairs basic electronic apparatus faults by 40 replacement of components UEENEEH103A Repair routine business equipment faults 120 UEENEEH104A Set up and test residential video/audio equipment 40 UEENEEH105A Verify functionality and compliance of custom 40 electronic installations UEENEEH106A Assemble and set up fixed video/audio components 120 and systems in buildings and premises UEENEEH107A Repair predictable faults in general electronic 40 apparatus UEENEEH108A Assemble and install reception antennae and signal 60 distribution equipment UEENEEH109A Set up and test gaming and game equipment 60 UEENEEH110A Install commercial video/audio system components 120 UEENEEH111A Troubleshoot single phase input d.c. power supplies 40 UEENEEH112A Troubleshoot digital sub-systems 80 UEENEEH113A Troubleshoot amplifiers in an electronic apparatus 80 UEENEEH114A Troubleshoot resonance circuits in an electronic 80 apparatus UEENEEH115A Develop software solutions for microcontroller based 60 systems UEENEEH116A Find and repair microwave amplifier section faults in 40 electronic apparatus UEENEEH117A Carry out repairs of predictable faults in video and 120 audio replay/recording apparatus UEENEEH118A Fault find and repair electronic apparatus 40 UEENEEH119A Repair predictable faults in television receivers 120 UEENEEH120A Fault find and repair gaming and games equipment 80 UEENEEH121A Fault find and repair high volume office equipment 120 UEENEEH122A Fault find and repair remote control apparatus 60 UEENEEH123A Fault find and repair microwave heating apparatus 40 UEENEEH124A Repair predictable faults in audio components 40 UEENEEH127A Set up and adjust commercial radio frequency (RF) 60 transmission and reception systems UEENEEH128A Install and test microwave antennae and waveguides 60 UEENEEH129B Fault find and repair navigation systems 60 UEENEEH130A Fault find and repair satellite-based surveillance and 60 observation systems UEENEEH131A Fault find and repair radar apparatus and systems 120

of 50 Unit Code Unit Title Nominal Hours UEENEEH132A Fault find and repair global positioning systems 60 UEENEEH133A Fault find and repair telecommunication apparatus and 60 systems UEENEEH134A Fault find and repair electronic medical equipment 120 UEENEEH135A Design custom electronic equipment installations 120 UEENEEH136A Design commercial video/audio installations 120 UEENEEH137A Program and commission commercial video/audio 40 systems UEENEEH138A Fault find and repair complex power supplies 40 UEENEEH139A Troubleshoot basic amplifier circuits 40 UEENEEH140A Fault find and repair sonar apparatus and systems 120 UEENEEH141A Manage computer systems/electronics projects 40 UEENEEH142A Solve oscillator problems 40 UEENEEH145A Develop engineering solutions to analogue electronic 80 problems UEENEEH146A Solve fundamental electronic communications system 40 problems UEENEEH147A Assess electronic apparatus compliance 60 UEENEEH148A Design and develop advanced digital systems 40 UEENEEH149A Develop engineering solutions to audio electronic 60 problems UEENEEH150A Assemble and set up basic security systems 80 UEENEEH151A Install large security systems 100 UEENEEH152A Enter instructions and test wired and wireless security 40 systems UEENEEH153A Program and test large security systems 120 UEENEEH154A Program and commission commercial security systems 60 UEENEEH155A Program and commission commercial access control 60 security systems UEENEEH156A Program and commission commercial security closed 60 circuit television systems UEENEEH157A Develop basic plans for integrating security systems 40 UEENEEH158A Design integrated security systems 40 UEENEEH159A Design integrated complex security systems for 60 multiple sites UEENEEH160A Plan large electronic projects 60 UEENEEH161A Install fire detection and warning system apparatus 40 UEENEEH162A Verify compliance and functionality of fire protection 60 system installations UEENEEH163A Enter and verify programs for fire protection systems 40 UEENEEH164A Commission large fire protection systems 40 UEENEEH165A Troubleshoot fire protection systems 40 UEENEEH166A Troubleshoot microcontroller based hardware systems 40 UEENEEH167A Commission electronics and communications systems 20 UEENEEH168A Modify/redesign of electronics and communications 20 systems UEENEEH169A Solve problems in basic electronic circuits 100 UEENEEH171A Troubleshoot faults in television receivers 120 UEENEEH172A Troubleshoot communication systems 80

of 50 Unit Code Unit Title Nominal Hours UEENEEH173A Troubleshoot professional audio reproduction 120 components UEENEEH174A Troubleshoot audio/video recording equipment 120 UEENEEH175A Troubleshooting in security system installations 60 UEENEEH176A Diagnose and rectify faults in electronic display circuits 60 UEENEEH177A Diagnose and rectify faults in recording and replay 60 equipment UEENEEH178A Diagnose and rectify faults in camera circuits and 60 equipment UEENEEH179A Diagnose and rectify faults in digital television circuits 80 and apparatus UEENEEH180A Diagnose and rectify faults in digital transmission 80 circuits and systems UEENEEH181A Design electronic printed circuit boards 40 UEENEEH182A Develop engineering solutions to RF amplifiers 40 problems UEENEEH183A Analyse the performance of wireless-based 40 electronic/communication systems UEENEEH184A Modify digital signal processing (DSP) based sub- 80 systems UEENEEH185A Design signal-conditioning subsystems 80 UEENEEH186A Commission satellite and microwave communication 40 systems UEENEEH187A Solve problems in electronic musical equipment 40 circuits UEENEEH188A Design and develop electronics/ computer systems 40 projects UEENEEH189A Provide Gate Array solutions for complex electronics 60 systems UEENEEH190A Provide engineering solutions to air traffic control 40 system problems UEENEEH191A Diagnose and rectify faults in air navigation circuits and 120 systems UEENEEH192A Develop solutions for air surveillance apparatus and 120 systems UEENEEI101A Use instrumentation drawings, specification, standards 40 and equipment manuals UEENEEI102A Solve problems in pressure measurement components 40 and systems UEENEEI103A Solve problems in density/level measurement 40 components and systems UEENEEI104A Solve problems in flow measurement components and 40 systems UEENEEI105A Solve problems in temperature measurement 40 components and systems UEENEEI106A Set up and adjust PID control loops 40 UEENEEI107A Install instrumentation and control cabling and tubing 20 UEENEEI108A Install instrumentation and control apparatus and 20 associated equipment

of 50 Unit Code Unit Title Nominal Hours UEENEEI110A Set up and adjust advanced PID process control loops 40 UEENEEI111A Find and rectify faults in process final control elements 40 UEENEEI112A Verify compliance and functionality of instrumentation 40 and control installations UEENEEI113A Setup and configure Human-Machine Interface (HMI) 60 and industrial networks UEENEEI114A Trouble shoot process control systems 60 UEENEEI115A Trouble shooting in medical equipment control systems 120 UEENEEI116A Assemble, enter and verify operating instructions in 20 microprocessor equipped devices UEENEEI117A Calibrate, adjust and test measuring instruments 40 UEENEEI118A Set up weighting measuring and control instruments 20 UEENEEI119A Set up industrial field control devices 60 UEENEEI120A Provide solutions to problems in industrial control 60 systems UEENEEI121A Trouble shoot in measuring and analysis systems 40 UEENEEI122A Assist in commissioning process and instrumentation 40 control systems UEENEEI123A Design electronic control systems 60 UEENEEI124A Fault find and repair analogue circuits and components 60 in electronic control systems UEENEEI125A Provide solutions to fluid circuit operations 60 UEENEEI126A Provide solutions to pneumatic/ hydraulic system 80 operations UEENEEI127A Analyse complex electronic circuits controlling fluids 80 UEENEEI128A Set up and configure controls on complex fluid systems 80 UEENEEI129A Set up electronically controlled mechanically operated 80 complex systems UEENEEI130A Set up electronically controlled robotically operated 80 complex systems UEENEEI131A Set up gas analysis measuring and control instruments 20 UEENEEI132A Set up water analysis measuring and control 20 instruments UEENEEI133A Set up scientific analysis measuring and control 20 instruments UEENEEI134A Manage instrumentation and control projects 40 UEENEEI135A Plan instrumentation and control projects 60 UEENEEI136A Manage automated control systems projects 40 UEENEEI137A Plan automated and control systems projects 60 UEENEEI138A Provide solutions to extra low voltage (ELV) electro- 60 pneumatic control systems and drives UEENEEI139A Diagnose and rectify faults in digital controls systems 60 UEENEEI140A Plan the electrical installation of integrated systems 20 UEENEEI141A Develop electrical integrated systems 20 UEENEEI142A Develop an electrical integrated system interface for 20 access through a touch screen UEENEEI143A Develop access control of electrical integrated systems 20 using logic-based programming tools UEENEEI144A Develop interfaces for multiple access methods to 20

of 50 Unit Code Unit Title Nominal Hours monitor, schedule and control an electrical integrated system UEENEEI145A Diagnose and rectify faults in a.c. motor drive systems 60 UEENEEI146A Diagnose and rectify faults in d.c. motor drive systems 60 UEENEEI147A Diagnose and rectify faults in servo drive systems 60 UEENEEI148A Solve problems in single phase electronic power 60 control circuits UEENEEI149A Solve problems in polyphase electronic power control 60 circuits UEENEEI150A Develop, enter and verify discrete control programs for 60 programmable controllers UEENEEI151A Develop, enter and verify word and analogue control 60 programs for programmable logic controllers. UEENEEI152A Develop, enter and verify programs in Supervisory 60 Control and Data Acquisition systems UEENEEI153A Design and configure Human-Machine Interface (HMI) 60 networks UEENEEI154A Design and use advanced programming tools PC 120 networks and HMI Interfacing UEENEEI155A Develop structured programs to control external 40 devices UEENEEI156A Develop and test code for microcontroller devices 60 UEENEEI157A Configure and maintain industrial control system 60 networks UEENEEJ040B Manage refrigeration and air conditioning projects 40 UEENEEJ069B Plan refrigeration and air conditioning projects 60 UEENEEJ102A Prepare and connect refrigerant tubing and fittings 40 UEENEEJ103A Establish the basic operating conditions of vapour 60 compression systems UEENEEJ104A Establish the basic operating conditions of air 20 conditioning systems UEENEEJ105A Position, assemble and start up single head split air 70 conditioning and water heating heat pump systems UEENEEJ106A Install refrigerant pipe work, flow controls and 60 accessories UEENEEJ107A Install air conditioning and refrigeration systems, major 80 components and associated equipment UEENEEJ108A Recover, pressure test, evacuate, charge and leak test 60 refrigerants UEENEEJ109A Verify functionality and compliance of refrigeration and 20 air conditioning installations UEENEEJ110A Select refrigerant piping, accessories and associated 60 controls UEENEEJ111A Diagnose and rectify faults in air conditioning and 40 refrigeration systems and components UEENEEJ112A Diagnose and rectify faults in complex air conditioning/ 100 refrigeration systems UEENEEJ113A Commission air conditioning and refrigeration systems 40 UEENEEJ114A Resolve problems in hydronic systems 40

of 50 Unit Code Unit Title Nominal Hours UEENEEJ115A Resolve problems in beverage dispensers 40 UEENEEJ116A Resolve problems in transport refrigeration systems 20 UEENEEJ117A Resolve problems in ultra-low temperature refrigeration 20 systems UEENEEJ118A Resolve problems in post mix refrigeration systems 20 UEENEEJ119A Resolve problems in ice making systems 20 UEENEEJ120A Resolve problems in industrial refrigeration systems 20 UEENEEJ121A Monitor and adjust refrigeration energy management 40 systems UEENEEJ122A Diagnose faults in complex HVAC /refrigeration control 80 systems UEENEEJ123A Commission complex (HVAC) heating, ventilation and 80 air conditioning systems UEENEEJ124A Commission refrigeration/air conditioning hydronic 80 systems UEENEEJ125A Commission complex refrigeration systems and 80 equipment UEENEEJ126A Commission complex refrigeration/air conditioning 80 control systems UEENEEJ127A Establish the thermodynamic parameters of 80 refrigeration and air conditioning systems UEENEEJ128A Produce HVAC/R system design drawings 80 UEENEEJ129A Establish heat loads for commercial refrigeration 80 and/or air conditioning applications UEENEEJ130A Produce HVAC/R control system diagrams 40 UEENEEJ131A Determine noise and vibration encountered in HVAC/R 40 applications UEENEEJ132A Design commercial refrigeration systems and select 80 components UEENEEJ133A Design industrial refrigeration systems and select 80 components UEENEEJ134A Design heating, ventilation and air conditioning (HVAC) 60 systems and select components UEENEEJ135A Design control systems for refrigeration or heating, 80 ventilation and air conditioning systems UEENEEJ136A Evaluate and report on building services energy 80 management systems UEENEEJ137A Evaluate and report on the indoor air quality of 40 buildings UEENEEJ138A Analyse vibration and noise in refrigeration and air 80 conditioning systems UEENEEJ139A Develop specifications and prepare drawings for 60 HVAC/Refrigeration projects UEENEEJ141A Design complex commercial refrigeration systems and 40 select equipment UEENEEJ142A Design complex industrial refrigeration systems and 40 select equipment UEENEEJ143A Design complex air conditioning systems and select 120 equipment

of 50 Unit Code Unit Title Nominal Hours UEENEEJ144A Design mechanical ventilation/exhaust systems and 40 select equipment UEENEEJ145A Design hydronic systems and select equipment 80 UEENEEJ146A Design complex control systems for refrigeration, 80 heating, ventilation or air conditioning systems UEENEEJ147A Audit energy use for commercial HVAC/Refrigeration 40 systems UEENEEJ148A Audit HVAC/R control systems for compliance with 60 regulations and standards UEENEEJ149A Develop heat exchanger design specifications 80 UEENEEJ150A Evaluate new and alternative technologies applicable 40 to electrotechnology applications UEENEEJ151A Service small electrical appliances and power tools 60 UEENEEJ153A Find and rectify faults in motors and associated 60 controls in refrigeration and air conditioning systems UEENEEJ154A Find and rectify faults in appliance control systems and 60 devices UEENEEJ155A Service refrigeration appliances 60 UEENEEJ156A Service clothes washing machines and dryers 40 UEENEEJ157A Service electrical heating appliances 60 UEENEEJ158A Service dishwasher machines 40 UEENEEJ159A Service gas heating appliances 40 UEENEEJ161A Verify functionality and compliance of appliances 20 UEENEEJ162A Recover, pressure test, evacuate, charge and leak test 50 refrigerants — appliances UEENEEJ164A Analyse the operation of HVAC air and hydronic 80 systems UEENEEJ165A Evaluate thermodynamic and fluid parameters of 100 refrigeration systems UEENEEJ166A Resolve problems in dairy refrigeration systems 20 UEENEEJ167A Resolve problems in central plant air conditioning 40 systems UEENEEJ168A Maintain microbial control of refrigeration and air 20 conditioning systems UEENEEJ170A Diagnose and rectify faults in air conditioning and 80 refrigeration control systems UEENEEJ171A Resolve problems in refrigerated beverage vending 20 cabinets UEENEEJ172A Recover, pressure test, evacuate, charge and leak test 60 refrigerants — split systems UEENEEJ173A Service and repair microwave ovens 40 UEENEEJ174A Apply safety awareness and legal requirements for 10 hydrocarbon refrigerants UEENEEJ175A Service and repair self contained hydrocarbon air 20 conditioning and refrigeration systems UEENEEJ176A Install and commission hydrocarbon refrigerant 20 systems, components and associated equipment UEENEEJ177A Design hydrocarbon refrigerant systems 40 UEENEEJ178A Apply safety awareness and legal requirements for 10

of 50 Unit Code Unit Title Nominal Hours ammonia refrigerant UEENEEJ179A Repair and service ammonia refrigeration systems 20 UEENEEJ180A Install and commission ammonia refrigeration systems, 20 components and associated equipment UEENEEJ181A Design ammonia refrigerated systems 40 UEENEEJ182A Repair and service secondary refrigeration systems 20 UEENEEJ183A Design secondary refrigerant systems 40 UEENEEJ184A Apply safety awareness and legal requirements for 10 carbon dioxide refrigerant UEENEEJ185A Repair and service carbon dioxide refrigeration 20 systems UEENEEJ186A Install and commission carbon dioxide refrigeration 20 systems, components and associated equipment UEENEEJ187A Design carbon dioxide refrigerated systems 40 UEENEEJ188A Repair and service self contained carbon dioxide 20 refrigeration and heat pump systems UEENEEJ189A Service room air conditioners 30 UEENEEJ190A Select basic commercial refrigeration system 40 equipment, components and accessories UEENEEJ191A Select residential air conditioning system equipment, 40 components and accessories UEENEEJ192A Analyse the psychrometric performance of HVAC/R 50 systems UEENEEJ193A Analyse the thermodynamic performance of HVAC/R 40 systems UEENEEJ194A Solve problems in low voltage refrigeration circuits 60 UEENEEJ195A Establish the basic operating conditions of vapour 50 compression systems - appliances UEENEEJ196A Operate Ammonia Refrigeration Plan 40 UEENEEK101A Maintain safety and tidiness of remote area power 20 supply systems UEENEEK102A Work safely with remote area power supply systems 20 UEENEEK103A Conduct periodic maintenance of remote area power 40 supply battery banks UEENEEK104A Conduct periodic maintenance of remote area power 40 supply generator sets UEENEEK105A Conduct periodic maintenance of remote area power 40 supply photo voltaic arrays UEENEEK106A Conduct periodic maintenance of remote area power 40 supply wind generators UEENEEK107A Conduct checks in the demand side use of remote 40 area power supplies (RAPS) UEENEEK108A Plan periodic maintenance schedules of remote area 40 power supplies (RAPS) UEENEEK109A Attend to breakdowns in remote area power supplies 20 (RAPS) UEENEEK110A Co-ordinate maintenance of renewable energy (RE) 20 apparatus and systems UEENEEK111A Assemble and connect remote area power supplies 60

of 50 Unit Code Unit Title Nominal Hours UEENEEK112A Provide basic sustainable energy solutions for energy 40 reduction in residential premises UEENEEK114A Promote sustainable energy practices in the 100 community UEENEEK116A Maintain and repair remote area power generation 40 facilities UEENEEK117A Maintain and repair facilities associated with remote 120 area essential service operations UEENEEK118A Maintain and monitor remote area essential service 120 (RAPS) operations UEENEEK120A Maintain operation of remote area power generation 120 plant UEENEEK121A Manage renewable energy (RE) projects 40 UEENEEK122A Plan renewable energy (RE) projects 60 UEENEEK123A Carry out basic repairs to renewable energy apparatus 80 UEENEEK124A Solve basic problems in micro hydro systems 20 UEENEEK125A Solve basic problems in photovoltaic energy apparatus 40 and systems UEENEEK127A Diagnose and rectify faults in renewable energy control 60 systems UEENEEK128A Solve problems in stand-alone renewable energy 60 systems UEENEEK129A Design renewable energy (RE) heating systems 120 UEENEEK130A Solve problems in wind energy conversion systems 60 rated up to 10 kW UEENEEK131A Design wind energy conversion systems (WECS) rated 60 to 10 kW UEENEEK132A Develop strategies to address environmental and 20 sustainability issues in the energy sector UEENEEK133A Design hybrid renewable power systems 80 UEENEEK134A Install ELV stand-alone photovoltaic power systems 60 UEENEEK135A Design grid connected photovoltaic power supply 60 systems UEENEEK136A Install, configure and commission LV micro-hydro 40 systems rated up to 6.4 kW UEENEEK137A Install, set up and maintain ELV micro-hydro systems 20 rated up to 6.4 kW UEENEEK138A Design micro-hydro systems rated to 6.4 kW 60 UEENEEK139A Design stand-alone renewable energy (RE) systems 40 UEENEEK140A Develop engineering solutions to renewable energy 60 (RE) problems UEENEEK142A Apply environmentally and sustainable procedures in 20 the energy sector UEENEEK143A Install small wind energy conversion systems rated up 20 to 10 kW for ELV stand-alone applications UEENEEK144A Install, configure and commission LV wind energy 40 conversion systems rated up to 10 kW UEENEEK145A Implement and monitor energy sector environmental and sustainable energy policies and procedures 20

of 50 Unit Code Unit Title Nominal Hours UEENEEK146A Design energy management controls for electrical installations in buildings 80 UEENEEK148A Install, configure and commission LV grid connected photovoltaic power systems 80 UEENEEK149A Verify compliance and functionality of a extra low voltage renewable energy installation 20 UEENEEK151A Develop effective engineering strategies for energy reduction in buildings 120 UEENEEK152A Develop strategies to address sustainability issues for 20 electrical installations UEENEEK153A Assess energy loads and uses for energy efficiency in 40 residential, office and retail premises UEENEEK154A Assess energy loads and uses for energy efficiency in 40 commercial facilities UEENEEK155A Assess energy loads and uses for energy efficiency in 40 industrial properties and enterprises UEENEEM019A Attend to breakdowns in hazardous areas — coal 20 mining UEENEEM020A Attend to breakdowns in hazardous areas — gas 20 atmospheres UEENEEM021A Attend to breakdowns in hazardous areas — dust 20 atmospheres UEENEEM022A Attend to breakdowns in hazardous areas — 20 pressurisation UEENEEM023A Install explosion-protected equipment and wiring 60 systems — coal mining UEENEEM024A Install explosion-protected equipment and wiring 60 systems — gas atmospheres UEENEEM025A Install explosion-protected equipment and wiring 60 systems — dust atmospheres UEENEEM026A Install explosion-protected equipment and wiring 60 systems — pressurisation UEENEEM027A Maintain equipment in hazardous areas — coal mining 60 UEENEEM028A Maintain equipment in hazardous areas — gas 60 atmospheres UEENEEM029A Maintain equipment in hazardous areas — dust 60 atmospheres UEENEEM030A Maintain equipment in hazardous areas — 60 pressurisation UEENEEM031A Overhaul and repair of explosion-protected equipment 60 — coal mining UEENEEM032A Overhaul and repair of explosion-protected equipment 60 — flameproof enclosures UEENEEM033A Overhaul and repair of explosion-protected equipment 60 — gas atmospheres UEENEEM034A Overhaul and repair of explosion-protected equipment 60 — dust atmospheres UEENEEM035A Conduct a conformity assessment of explosion- 40 protected equipment — coal mining

of 50 Unit Code Unit Title Nominal Hours UEENEEM036A Conduct a conformity assessment of explosion- 40 protected equipment — gas atmospheres UEENEEM037A Conduct a conformity assessment of explosion- 40 protected equipment — dust atmospheres UEENEEM038A Conduct testing of hazardous areas installations — 40 coal mining UEENEEM039A Conduct testing of hazardous areas installations — gas 40 atmospheres UEENEEM040A Conduct testing of hazardous areas installations — 40 dust atmospheres UEENEEM041A Conduct testing of hazardous area installations — 40 pressurisation UEENEEM042A Conduct visual inspection of hazardous areas 40 installations UEENEEM043A Conduct detailed inspection of hazardous areas 40 installations — coal mining UEENEEM044A Conduct detailed inspection of hazardous areas 40 installations — gas atmospheres UEENEEM045A Conduct detailed inspection of hazardous areas 40 installations — dust atmospheres UEENEEM046A Conduct detailed inspection of hazardous areas 40 installations — pressurisation UEENEEM047A Develop and manage maintenance programs for 20 hazardous areas electrical equipment — coal mining UEENEEM048A Develop and manage maintenance programs for 20 hazardous areas electrical equipment — gas atmospheres UEENEEM049A Develop and manage maintenance programs for 20 hazardous areas electrical equipment — dust atmospheres UEENEEM050A Develop and manage maintenance programs for 20 hazardous areas electrical equipment — pressurisation UEENEEM052A Classify hazardous areas — gas atmospheres 40 UEENEEM053A Classify hazardous areas — dust atmospheres 40 UEENEEM054A Plan electrical installations for hazardous areas — gas 20 atmospheres UEENEEM055A Plan electrical installations for hazardous areas — dust 20 atmospheres UEENEEM056A Plan electrical installations for hazardous areas — 20 pressurisation UEENEEM057A Design explosion-protected electrical systems and 20 installations — gas atmospheres UEENEEM058A Design explosion-protected electrical systems and 20 installations — dust atmospheres UEENEEM059A Design explosion-protected electrical systems and 20 installations — pressurisation UEENEEM060A Carry out overhaul and repair of explosion-protected 60 equipment — coal mining UEENEEM061A Carry out overhaul and repair of explosion-protected 60

of 50 Unit Code Unit Title Nominal Hours equipment — flameproof enclosures UEENEEM062A Carry out overhaul and repair of explosion-protected 60 equipment — gas atmospheres UEENEEM063A Carry out overhaul and repair of explosion-protected 60 equipment — dust atmospheres UEENEEM064A Conduct audit of hazardous areas installations — coal 60 mining UEENEEM065A Conduct audit of hazardous areas installations — gas 60 atmospheres UEENEEM066A Conduct audit of hazardous areas installations — dust 60 atmospheres UEENEEM067A Assess the fitness-for-purpose of hazardous areas 60 explosion-protected equipment — coal mining UEENEEM068A Assess the fitness-for-purpose of hazardous areas 60 explosion-protected equipment — gas atmospheres UEENEEM069A Assess the fitness-for-purpose of hazardous areas 60 explosion-protected equipment — dust atmospheres UEENEEM070A Repair reeling, trailing and flexible cables 60 UEENEEM071A Test reeling, trailing and flexible cables 60 UEENEEM072A Inspect and fit plugs/couplers for reeling, trailing and 60 flexible cables UEENEEM073A Verify compliance of repaired reeling, trailing and 60 flexible cables UEENEEM074A Plan electrical installations in hazardous areas — Coal 20 mining UEENEEM075A Design explosion-protected electrical systems — Coal 20 mining UEENEEM076A Use and maintain the integrity of a portable gas 20 detection device UEENEEM077A Install and maintain the integrity of fixed gas detection 20 equipent UEENEEM078A Manage compliance of hazardous areas 20 UEENEEM079A Design of gas detection systems 20 UEENEEM080A Report on the integrity of explosion-protected 20 equipment in a hazardous area UEENEEN101A Maintain mechanical rail signalling equipment and infrastructure 20 UEENEEN102A Assemble and wire internal electrical rail signalling equipment 20 UEENEEN103A Install and maintain rail track circuit leads and bonds 20 UEENEEN104A Test copper rail signalling cables 20 UEENEEN105A Install and maintain rail signalling power supplies 20 UEENEEN106A Install and maintain non-vital screen based control systems 20 UEENEEN107A Install and maintain active level crossing equipment 20 UEENEEN108A Install and maintain power operated point actuating devices 20 UEENEEN109A Install and maintain train detection equipment 20 UEENEEN110A Install and maintain non-vital telemetry systems 20

of 50 Unit Code Unit Title Nominal Hours UEENEEN111A Install and maintain trackside signal and train protection equipment 20 UEENEEN112A Install and maintain vital relay interlocking systems 20 UEENEEN114A Install and maintain computer based interlocking rail systems 20 UEENEEN116A Maintain electronic and microprocessor-based remote control systems 20 UEENEEN118A Find and repair rail signalling system faults 20 UEENEEN121A Repair rail signalling power and control cables 20 UEENEEN126A Develop rail signalling system maintenance programs 20 UEENEEN127A Decommission electrical and electro-mechanical rail signalling from service 20 UEENEEN128A Test and commission rail power equipment 20 UEENEEP010A Disconnect / reconnect appliances connected to low voltage installation wiring 60 UEENEEP011A Disconnect / reconnect neon signs connected to low voltage installation wiring 60 UEENEEP012A Disconnect / reconnect composite appliances 60 connected to low voltage installation wiring UEENEEP013A Disconnect / reconnect control devices connected to 60 low voltage installation wiring UEENEEP014A Disconnect / reconnect water heaters connected to low 60 voltage installation wiring UEENEEP015A Disconnect / reconnect motors connected to low 60 voltage installation wiring UEENEEP016A Locate and rectify faults in low voltage appliances 20 using set procedures UEENEEP017A Locate and rectify faults in low voltage composite 20 appliances using set procedures UEENEEP018A Locate and rectify faults in low voltage control devices 20 using set procedures UEENEEP019A Locate and rectify faults in low voltage water heaters 20 using set procedures UEENEEP020A Locate and rectify faults in low voltage motors using 20 set procedures UEENEEP021A Disconnect / reconnect explosion-protected appliances 60 and control devices connected to low voltage installation wiring UEENEEP022A Disconnect and reconnect 3.3 kV electric propulsion 60 components of self-propelled earth moving vehicles UEENEEP023A Attach flexible cables and plugs to electrical equipment 40 connected to a HV supply UEENEEP024A Attach cords and plugs to electrical equipment for 20 connection to a single phase 230 Volt supply UEENEEP025A Attach cords, cables and plugs to electrical equipment 20 for connection to 1000 Va.c. or 1500 Vd.c. supply UEENEEP026A Conduct in-service safety testing of electrical cord 20 connected equipment and cord assemblies UEENEER001B Contribute to the planning of a research project 80

of 50 Unit Code Unit Title Nominal Hours UEENEER002B Contribute to the conduct of a research project 80 UEENEER003B Contribute to the development of a 80 product/application/service UEENEER004B Contribute to the trial of a product/application/service 80 UEENEER005B Contribute to intellectual property management 80 UEENEER006B Contribute to the commercialisation of a 80 products/applications/services

of 50 SAMPLE TRAINING PROGRAMS

A range of Sample Training Plans have been provided to demonstrate the flexibility of qualifications contained in the UEE11 Electrotechnology Training Package, but are by no means mandatory.

Occupation / Work Assistant Work Function Qualification Certificate I in ElectroComms Skills Title Qualification UEE10111 Code Description People gaining this qualification will be able to perform basic work activities, including identifying and using a range of components, accessories, materials, tools, equipment, technologies, and customs for carrying out work in the Electrotechnology –Communications Industry. Sectors in the industry are electronics, electrical, communications, including telecommunications – voice, data, video and information technology, computer systems, instrumentation, lifts, refrigeration and air conditioning, and renewable/sustainable energy. Notes For advice on how to choose electives other than those listed below, please refer to the UEE11 Electrotechnology Training Package and its Qualifications Packaging Rules or contact the CMM Engineering Industries on (03) 9286 9880. Unit Code Unit Title Hours Core Use computer applications relevant to a UEENEED101A 20 workplace Apply Occupational Health and Safety UEENEEE101A regulations, codes and practices in the 20 workplace Identify and select components, accessories UEENEEE179A 20 and materials for energy sector work activities Carry out routine work activities in an energy UEENEEE148A 40 sector environment Apply environmentally and sustainable energy UEENEEK142A 20 procedures in the energy sector Electives Group A UEENEEC001B Maintain documentation 20 Electives Group B UEENEEE103A Solve problems in ELV single path circuits 40 Total hours 180

of 50 Occupation / Computer Assembler Work Function Qualification Certificate II in Computer Assembly and Repair Title Qualification UEE20511 Code Description Persons gaining this qualification will be able to select components and assemble computer to customer specifications and carry out routine hardware repairs (generally by replacement) of known faulty components following prescribed routines Notes For advice on how to choose electives other than those listed below, please refer to the UEE11 Electrotechnology Training Package and its Qualifications Packaging Rules or contact the CMM Engineering Industries on (03) 9286 9880. Unit Code Unit Title Hours Core UEENEED102A Assemble, set-up and test computing devices 80 Participate in development and follow a UEENEEE038B 20 personal competency development plan Apply Occupational Health and Safety UEENEEE101A regulations, codes and practices in the 20 workplace Fabricate, assemble and dismantle utilities UEENEEE102A 40 industry components Document and apply measures to control OHS UEENEEE137A 20 risks associated with electrotechnology work Apply environmentally and sustainable energy UEENEEK142A 20 procedures in the energy sector Electives

Group A UEENEEC001B Maintain documentation 20 Source and purchase material/parts for UEENEEC002B 20 installation or service jobs Receive and store materials and equipment for UEENEEC008B 20 electrotechnology work Electives

Group B Use computer applications relevant to a UEENEED101A 20 workplace UEENEED143A Install and configure a client computer 40 operating system and software Set up and configure basic local area network UEENEED146A 40 (LAN) Total hours 360

of 50 Occupation / Electrician Work Function Qualification Certificate III in Electrotechnology Electrician Title Qualification UEE30811 Code Description Persons gaining this qualification will be able to select, install, set up, test, fault find, repair and maintain electrical systems and equipment in building and premises. They will also have fulfilled ERAC requirements for an ‘Electrician’s licence’. Notes For advice on how to choose electives other than those listed below, please refer to the UEE11 Electrotechnology Training Package and its Qualifications Packaging Rules or contact the CMM Engineering Industries on (03) 9286 9880. Unit Code Unit Title Hours Core Participate in electrical work and competency UEENEEC020B 20 development activities Apply Occupational Health and Safety UEENEEE101A regulations, codes and practices in the 20 workplace Fabricate, assemble and dismantle utilities UEENEEE102A 40 industry components UEENEEE104A Solve problems in d.c. circuits 80 UEENEEE105A Fix and secure electrotechnology equipment 20 Use drawings, diagrams, schedules, UEENEEE107A 40 standards, codes and specifications Document and apply measures to control OHS UEENEEE137A 20 risks associated with electrotechnology work Solve problems in single and three phase low UEENEEG006A 80 voltage machines Solve problems in single and three phase low UEENEEG033A 60 voltage electrical apparatus and circuits Arrange circuits, control and protection for UEENEEG063A 40 general electrical installations

of 50 Solve problems in electromagnetic devices UEENEEG101A 60 and related circuits UEENEEG102A Solve problems in low voltage a.c. circuits 80 UEENEEG103A Install low voltage wiring and accessories 20 Install appliances, switchgear and associated UEENEEG104A accessories for low voltage electrical 20 installations Verify compliance and functionality of low UEENEEG105A 60 voltage general electrical installations Terminate cables, cords and accessories for UEENEEG106A 40 low voltage circuits Select wiring systems and cables for low UEENEEG107A 80 voltage general electrical installations Trouble-shoot and repair faults in low voltage UEENEEG108A 80 electrical apparatus and circuits UEENEEG109A Develop and connect electrical control circuits 80 Apply environmentally and sustainable energy UEENEEK142A 20 procedures in the energy sector Group A

Electives Use computer applications relevant to a UEENEED101A 20 workplace Group B

Electives UEENEEF102A Install and maintain cabling for multiple access 120 to telecommunication services Total Hours 1100 Occupation / Refrigeration and Air-Conditioning Mechanic Work Function Qualification Certificate III in Air-conditioning and Refrigeration Title Qualification UEE32211 Code Description Persons gaining this qualification will be able to select components, install, set up, test, fault find, repair and maintain refrigeration systems and equipment that apply to food storage and preservation and air conditioning and air distribution equipment in buildings and premises. They will also have fulfilled the regulatory requirements for purchasing and handling refrigerants. Notes For advice on how to choose electives other than those listed below, please refer to the UEE11 Electrotechnology Training Package and its Qualifications Packaging Rules or contact the CMM Engineering Industries on (03) 9286 9880. Unit Code Unit Title Hours Core Participate in refrigeration and air conditioning UEENEEC025B 20 work and competency development activities

of 50 Apply Occupational Health and Safety UEENEEE101A regulations, codes and practices in the 20 workplace Fabricate, assemble and dismantle utilities UEENEEE102A 40 industry components UEENEEE103A Solve problems in ELV single path circuits 40 UEENEEE105A Fix and secure electrotechnology equipment 20 Use drawings, diagrams, schedules, UEENEEE107A 40 standards, codes and specifications Document and apply measures to control OHS UEENEEE137A 20 risks associated with electrotechnology work Prepare and connect refrigerant tubing and UEENEEJ102A 40 fittings Establish the basic operating conditions of UEENEEJ103A 60 vapour compression systems Establish the basic operating conditions of air UEENEEJ104A 20 conditioning systems Install refrigerant pipe work, flow controls and UEENEEJ106A 60 accessories Install air conditioning and refrigeration UEENEEJ107A systems, major components and associated 80 equipment Recover, pressure test, evacuate, charge and UEENEEJ108A 60 leak test refrigerants Verify functionality and compliance of UEENEEJ109A 20 refrigeration and air conditioning installations Select refrigerant piping, accessories and UEENEEJ110A 60 associated controls Diagnose and rectify faults in air conditioning UEENEEJ111A 40 and refrigeration systems and components Commission air conditioning and refrigeration UEENEEJ113A 40 systems Find and rectify faults in motors and UEENEEJ153A associated controls in refrigeration and air 60 conditioning systems Diagnose and rectify faults in air conditioning UEENEEJ170A 80 and refrigeration control systems Solve problems in low voltage refrigeration UEENEEJ194A 60 circuits Apply environmentally and sustainable energy UEENEEK142A 20 procedures in the energy sector Disconnect / reconnect composite appliances UEENEEP012A 60 connected to low voltage installation wiring Unit Code Unit Title (Cont) Hours Locate and rectify faults in low voltage UEENEEP017A 20 composite appliances using set procedures Attach cords and plugs to electrical equipment UEENEEP024A for connection to a single phase 230 Volt 20 supply UEENEEP025A Attach cords, cables and plugs to electrical 20 equipment for connection to 1000 Va.c. or

of 50 1500 Vd.c. supply Electives

Group A UEENEEC001B Maintain documentation 20 Electives

Group B Resolve problems in transport refrigeration UEENEEJ116A 20 systems Resolve problems in ultra-low temperature UEENEEJ117A 20 refrigeration systems Total hours 1080 Occupation / Computer Technician Work Function Qualification Certificate IV in Computer Systems Title Qualification UEE40111 Code Description Persons gaining this qualification will be able to select, install, commission, fault find and maintain data processing, communications and control aspects of systems used for monitoring and control of systems for access, surveillance, safety and effective operation of manufacturing, buildings, structures, premises, precincts and personal computer and networks. Notes For advice on how to choose electives other than those listed below, please refer to the UEE11 Electrotechnology Training Package and its Qualifications Packaging Rules or contact the CMM Engineering Industries on (03) 9286 9880. Unit Code Unit Title Hours Core UEENEED102A Assemble, set-up and test computing devices 80 Use engineering applications software on UEENEED104A 40 personal computers Support computer hardware and software for UEENEED112A 120 engineering applications Install and configure a client computer UEENEED143A 40 operating system and software Set up and configure basic local area network UEENEED146A 40 (LAN) Participate in development and follow a UEENEEE038B 20 personal competency development plan Apply Occupational Health and Safety UEENEEE101A regulations, codes and practices in the 20 workplace Fabricate, assemble and dismantle utilities UEENEEE102A 40 industry components UEENEEE103A Solve problems in ELV single path circuits 40

of 50 Implement and monitor energy sector OHS UEENEEE117A 20 policies and procedures Compile and produce an energy sector UEENEEE124A 60 detailed report Document and apply measures to control OHS UEENEEE137A 20 risks associated with electrotechnology work Implement and monitor energy sector UEENEEK145A environmental and sustainable energy policies 20 and procedures Electives

Group A UEENEEC001B Maintain documentation 20 Source and purchase material/parts for UEENEEC002B 20 installation or service jobs Use computer applications relevant to a UEENEED101A 20 workplace Comply with scheduled and preventative UEENEEE009B 20 maintenance program processes Electives Group B UEENEEA101A Assemble electronic components 40 UEENEEA102A Select electronic components for assembly 20 Unit Unit Code Unit Title (Cont) Code UEENEEA104A Modify electronic sub assemblies 40 Troubleshoot microcontroller based hardware UEENEEH166A 40 systems UEENEEH169A Solve problems in basic electronic circuits 100 Use instrumentation drawings, specification, UEENEEI101A 40 standards and equipment manuals Electives

Group C Prepare specifications for the supply of UEENEEC004B materials and equipment for electrotechnology 40 projects UEENEEC005B Estimate electrotechnology projects 40 Install and configure network systems for UEENEED117A 120 internetworking Integrate multiple computer operating systems UEENEED124A 80 on a client server local area network UEENEEH181A Design electronic printed circuit boards 40 Total hours 1240 Occupation / Production Controller Work Function Qualification Diploma of Electrical and Instrumentation Title

of 50 Qualification UEE50211 Code Description Persons gaining this qualification will be able to select, install, commission, maintain and diagnose faults/malfunctions on electrical, instrumentation and control equipment and systems. They will also have fulfilled ERAC requirements for an ‘Electrician’s licence’. Notes For advice on how to choose electives other than those listed below, please refer to the UEE11 Electrotechnology Training Package and its Qualifications Packaging Rules or contact the CMM Engineering Industries on (03) 9286 9880. Unit Code Unit Title Hours Core Participate in development and follow a UEENEEE038B 20 personal competency development plan Write specifications for electrotechnology UEENEEE084A 40 engineering projects Apply Occupational Health and Safety UEENEEE101A regulations, codes and practices in the 20 workplace Fabricate, assemble and dismantle utilities UEENEEE102A 40 industry components UEENEEE104A Solve problems in d.c. circuits 80 UEENEEE105A Fix and secure electrotechnology equipment 20 Use drawings, diagrams, schedules, UEENEEE107A 40 standards, codes and specifications Implement and monitor energy sector OHS UEENEEE117A 20 policies and procedures Compile and produce an energy sector UEENEEE124A 60 detailed report Document and apply measures to control OHS UEENEEE137A 20 risks associated with electrotechnology work Solve problems in single and three phase low UEENEEG006A 80 voltage machines Solve problems in single and three phase low UEENEEG033A 60 voltage electrical apparatus and circuits Arrange circuits, control and protection for UEENEEG063A 40 general electrical installations Solve problems in electromagnetic devices UEENEEG101A 60 and related circuits UEENEEG102A Solve problems in low voltage a.c. circuits 80 UEENEEG103A Install low voltage wiring and accessories 20 Install appliances, switchgear and associated UEENEEG104A accessories for low voltage electrical 20 installations Verify compliance and functionality of low UEENEEG105A 60 voltage general electrical installations Terminate cables, cords and accessories for UEENEEG106A 40 low voltage circuits

of 50 Select wiring systems and cables for low UEENEEG107A 80 voltage general electrical installations Trouble-shoot and repair faults in low voltage UEENEEG108A 80 electrical apparatus and circuits UEENEEG109A Develop and connect electrical control circuits 80 Use instrumentation drawings, specification, UEENEEI101A 40 standards and equipment manuals Unit Code Unit Title (Cont) Hours Solve problems in pressure measurement UEENEEI102A 40 components and systems Solve problems in density/level measurement UEENEEI103A 40 components and systems Solve problems in flow measurement UEENEEI104A 40 components and systems Solve problems in temperature measurement UEENEEI105A 40 components and systems UEENEEI106A Set up and adjust PID control loops 40 Install instrumentation and control cabling and UEENEEI107A 20 tubing Install instrumentation and control apparatus UEENEEI108A 20 and associated equipment Set up and adjust advanced PID process UEENEEI110A 40 control loops Find and rectify faults in process final control UEENEEI111A 40 elements Verify compliance and functionality of UEENEEI112A 40 instrumentation and control installations Setup and configure Human-Machine Interface UEENEEI113A 60 (HMI) and industrial networks Develop, enter and verify discrete control UEENEEI150A 60 programs for programmable controllers Develop strategies to address environmental UEENEEK132A 20 and sustainability issues in the energy sector Electives Group C Develop access control of electrical integrated UEENEEI143A 20 systems using logic-based programming tools Group D Develop and test code for microcontroller UEENEEI156A 60 devices Total hours 1680 Occupation / Electronics Engineering Associate Work Function Qualification Advanced Diploma of Electronics and Title Communications Engineering Qualification UEE60211 Code Description People gaining this qualification are able to design and validate/evaluate electronics and communicatons equipment and systems, manage risk, estimate and

of 50 manage projects and provide technical advice/sales Notes For advice on how to choose electives other than those listed below, please refer to the UEE11 Electrotechnology Training Package and its Qualifications Packaging Rules or contact the CMM Engineering Industries on (03) 9286 9880. Unit Code Unit Title Hours Core Develop design briefs for electrotechnology UEENEEE015B 40 projects Participate in development and follow a UEENEEE038B 20 personal competency development plan Contribute to risk management in UEENEEE078B 20 electrotechnology systems Apply Occupational Health and Safety UEENEEE101A regulations, codes and practices in the 20 workplace Implement and monitor energy sector OHS UEENEEE117A 20 policies and procedures Document and apply measures to control OHS UEENEEE137A 20 risks associated with electrotechnology work UEENEEH141A Manage computer systems/electronics projects 40 Commission electronics and communications UEENEEH167A 20 systems Modify/redesign of electronics and UEENEEH168A 20 communications systems Design and develop electronics/ computer UEENEEH188A 40 systems projects Develop strategies to address environmental UEENEEK132A 20 and sustainability issues in the energy sector Electives Group A Apply material science to solving UEENEEE081A 60 electrotechnology engineering problems Apply physics to solving electrotechnology UEENEEE082A 60 engineering problems ICTTEN3056A Install telecommunications network equipment 60 Electives

Group B UEENEEA101A Assemble electronic components 40 Use engineering applications software on UEENEED104A 40 personal computers Fabricate, assemble and dismantle utilities UEENEEE102A 40 industry components UEENEEE104A Solve problems in d.c. circuits 80 Repairs basic electronic apparatus faults by UEENEEH102A 40 replacement of components UEENEEH112A Troubleshoot digital sub-systems 80

of 50 Troubleshoot amplifiers in an electronic UEENEEH113A 80 apparatus Unit Code Unit Title (Cont) Hours Troubleshoot resonance circuits in an UEENEEH114A 80 electronic apparatus Develop software solutions for microcontroller UEENEEH115A 60 based systems Find and repair microwave amplifier section UEENEEH116A 40 faults in electronic apparatus UEENEEH139A Troubleshoot basic amplifier circuits 40 Solve fundamental electronic communications UEENEEH146A 40 system problems Troubleshoot microcontroller based hardware UEENEEH166A 40 systems UEENEEH169A Solve problems in basic electronic circuits 100 UEENEEH172A Troubleshoot communication systems 80 Assemble, enter and verify operating UEENEEI116A instructions in microprocessor equipped 20 devices Electives

Group C Evaluate and modify object oriented code UEENEED103A 40 programs Electives

Group D Provide solutions to basic engineering UEENEEE126A 60 computational problems Develop engineering solutions to analogue UEENEEH145A 80 electronic problems UEENEEH148A Design and develop advanced digital systems 40 UEENEEH181A Design electronic printed circuit boards 40 Develop engineering solutions to RF amplifiers UEENEEH182A 40 problems Electives

Group E UEENEED152A Design embedded controller control systems 80 UEENEEE011C Manage risk in electrotechnology activities 60 Use advanced computational processes to UEENEEE127A provide solutions to energy sector engineering 120 problems UEENEEE129A Solve electrotechnical engineering problems 60 UEENEEH160A Plan large electronic projects 60 Modify digital signal processing (DSP) based UEENEEH184A 80 sub-systems Provide Gate Array solutions for complex UEENEEH189A 60 electronics systems Total hours 2160

of 50 Occupation / IT Systems Manager Work Function Qualification Advanced Diploma of Computer Systems Title Engineering Qualification UEE60411 Code Description Persons gaining this qualification will be able to design, install/validate/evaluate and administer computer networks and systems, manage risk, estimate and manage projects and provide technical advice/sales.

Notes For advice on how to choose electives other than those listed below, please refer to the UEE11 Electrotechnology Training Package and its Qualifications Packaging Rules or contact the CMM Engineering Industries on (03) 9286 9880. Unit Code Unit Title Hours Core UEENEED144A Commission industrial computer systems 20 Modify-redesign of industrial computer UEENEED145A 20 systems Develop design briefs for electrotechnology UEENEEE015B 40 projects Participate in development and follow a UEENEEE038B 20 personal competency development plan Contribute to risk management in UEENEEE078B 20 electrotechnology systems Apply Occupational Health and Safety UEENEEE101A regulations, codes and practices in the 20 workplace Implement and monitor energy sector OHS UEENEEE117A 20 policies and procedures Document and apply measures to control OHS UEENEEE137A 20 risks associated with electrotechnology work UEENEEH141A Manage computer systems/electronics projects 40 Design and develop electronics/ computer UEENEEH188A 40 systems projects Develop strategies to address environmental UEENEEK132A 20 and sustainability issues in the energy sector Electives

Group A Apply material science to solving UEENEEE081A 60 electrotechnology engineering problems Apply physics to solving electrotechnology UEENEEE082A 60 engineering problems Electives

Group B UEENEED102A Assemble, set-up and test computing devices 80 Use engineering applications software on UEENEED104A 40 personal computers

of 50 Support computer hardware and software for UEENEED112A 120 engineering applications Develop web pages for engineering UEENEED129A 40 applications Install and configure a client computer UEENEED143A 40 operating system and software Set up and configure basic local area network UEENEED146A 40 (LAN) Fabricate, assemble and dismantle utilities UEENEEE102A 40 industry components Repairs basic electronic apparatus faults by UEENEEH102A 40 replacement of components UEENEEH112A Troubleshoot digital sub-systems 80 Unit Code Unit Title (Cont) Hours Electives

Group C Install and administer Unix based networked UEENEED113A 80 computers UEENEED115A Administer computer networks 80 Install and configure network systems for UEENEED117A 120 internetworking Electives

Group D Provide solutions to basic engineering UEENEEE126A 60 computational problems Design and implement network systems for UEENEED118A 120 internetworking Integrate multiple computer operating systems UEENEED124A 80 on a client server local area network Electives

Group E UEENEED148A Plan industrial computer systems projects 60 UEENEEE129A Solve electrotechnical engineering problems 60 Use advanced computational processes to UEENEEE127A provide solutions to energy sector engineering 120 problems Design and manage enterprise computer UEENEED114A 120 networks UEENEED116A Develop computer network services 120 Design and implement security for UEENEED122A 100 Internetworking systems UEENEED152A Design embedded controller control systems 80 Develop energy sector computer network UEENEED149A 80 applications infrastructure Total hours 2200

of 50 Occupation / Electrical Installations designer Work Function Qualification Advanced Diploma of Engineering Technology - Title Electrical Qualification UEE62111 Code Description Persons gaining this qualification will be able to design, install/validate/evaluate and administer electrical installations, manage risk, estimate and manage projects and provide technical advice/sales Notes For advice on how to choose electives other than those listed below, please refer to the UEE11 Electrotechnology Training Package and its Qualifications Packaging Rules or contact the CMM Engineering Industries on (03) 9286 9880. Unit Code Unit Title Hours Core Use engineering applications software on UEENEED104A 40 personal computers UEENEEE011C Manage risk in electrotechnology activities 60 Develop design briefs for electrotechnology UEENEEE015B 40 projects Write specifications for electrical engineering UEENEEE071B 40 projects Apply industry and community standards to UEENEEE080A 20 engineering activities Apply material science to solving UEENEEE081A 60 electrotechnology engineering problems Apply physics to solving electrotechnology UEENEEE082A 60 engineering problems Establish and follow a competency UEENEEE083A development plan in an electrotechnology 20 engineering discipline Apply Occupational Health and Safety UEENEEE101A regulations, codes and practices in the 20 workplace Fabricate, assemble and dismantle utilities UEENEEE102A 40 industry components UEENEEE104A Solve problems in d.c. circuits 80 Use drawings, diagrams, schedules, UEENEEE107A 40 standards, codes and specifications Implement and monitor energy sector OHS UEENEEE117A 20 policies and procedures Compile and produce an energy sector UEENEEE124A 60 detailed report Provide engineering solutions for problems in UEENEEE125A 60 complex multiple path circuit UEENEEE126A Provide solutions to basic engineering 60

of 50 computational problems Document and apply measures to control OHS UEENEEE137A 20 risks associated with electrotechnology work Solve problems in single and three phase low UEENEEG006A 80 voltage machines Solve problems in single and three phase low UEENEEG033A 60 voltage electrical apparatus and circuits Arrange circuits, control and protection for UEENEEG063A 40 general electrical installations Solve problems in electromagnetic devices UEENEEG101A 60 and related circuits Unit Code Unit Title (Cont) Hours UEENEEG102A Solve problems in low voltage a.c. circuits 80 Terminate cables, cords and accessories for UEENEEG106A 40 low voltage circuits Select wiring systems and cables for low UEENEEG107A 80 voltage general electrical installations Provide engineering solutions to problems in UEENEEG149A 60 complex polyphase power circuits UEENEEG169A Manage large electrical projects 40 UEENEEG170A Plan large electrical projects 60 Develop strategies to address environmental UEENEEK132A 20 and sustainability issues in the energy sector Electives

Group A Trouble-shoot and repair faults in low voltage UEENEEG108A 80 electrical apparatus and circuits UEENEEI119A Set up industrial field control devices 60 Provide solutions to problems in industrial UEENEEI120A 60 control systems Fault find and repair analogue circuits and UEENEEI124A 60 components in electronic control systems Diagnose and rectify faults in digital controls UEENEEI139A 60 systems Electives

Group B Develop, enter and verify discrete control UEENEEI150A 60 programs for programmable controllers Electives

Group C Develop, enter and verify word and analogue UEENEEI151A control programs for programmable logic 60 controllers. Develop, enter and verify programs in UEENEEI152A Supervisory Control and Data Acquisition 60 systems Electives

Group E UEENEEE127A Use advanced computational processes to 120

of 50 provide solutions to energy sector engineering problems Design and use advanced programming tools UEENEEI154A 120 PC networks and HMI Interfacing Develop engineering solutions for induction UEENEEG145A 60 machine and control problems Total hours 2160

of 50 CONTACTS AND LINKS

Industry Skills Council (ISC)

EE-Oz Training This ISC is responsible Unit 2 Standards for developing this 48 Mort Street UEE11 Electrotechnology BRADDON, ACT, 2612 Training Package and Phone: (02) 6262 7055 can be contacted for further information. Fax: (02) 6257 4222 You can also source Email: [email protected] copies of the Training Package and support Web: http://www.ee-oz.com.au material.

National Register for VET in Australia

Training.gov.au TGA is the Australian training.gov.au (TGA) governments’ official National Register of information on Training Packages, qualifications, courses, units of competency and RTOs.

Australian Government

The Department DIISRTE provides a http://www.innovation.gov.au of Industry, range of services and You may also find Department of Education Innovation, resources to assist in Employment and Workplace Relations website Science, delivery of Training of use. Research and Packages. Search the Tertiary DIISRTE website for http://www.deewr.gov.au Education links to a range of (DIISRTE) relevant resources and publications.

State Government

Department of Higher Education and General information: Education and Skills Group is www.skills.vic.gov.au Early Childhood responsible for funding Development and the implementation Approved Training Schemes: Higher of Vocational Education http://www.skills.vic.gov.au/corporate/publication Education and and Training (VET) in s/brochures-and-fact-sheets/apprenticeships- Skills Group Victoria, including and-traineeships-in-victoria-industry-guides Apprenticeships and Traineeships.

Curriculum Maintenance Manager (CMM)

of 50 Engineering The CMM service is George Adda Industries provided by Executive Box Hill Institute of TAFE, Officers located within Victorian TAFE Private Bag 2014, Box Hill, institutes on behalf of Victoria, 3128 Skills Victoria. Phone: (03) 9286 9880 Fax: (03) 9286 9800 Email: [email protected] Web: http://trainingsupport.skills.vic.gov.au/cmminf.cf m

State VET Regulatory Authority

Victorian The VRQA is a www.vrqa.vic.gov.au statutory authority Registration and Phone: 03 9637 2806 Qualifications responsible for the Authority registration of education (VRQA) and training providers in Victoria to ensure the delivery of quality education and training.

National VET Regulatory Authority

Australian Skills ASQA is the national www.asqa.gov.au regulator for Australia’s Quality Authority Info line: 1300 701 801 (ASQA) VET sector vocational education and training sector.

ASQA regulates courses and training providers to ensure nationally approved quality standards are met.

Industry Regulatory Body

Energy Safe The industry Regulatory Level 5 Building 2 Victoria body can provide 4 Riverside Quay advice on licensing, legislative or regulatory Southbank, VIC, 3006 requirements which Postal Address: may impact on the delivery of training or PO BOX 262 the issuance of Collins Street West qualifications in this Training Package. Melbourne, Vic 8007

of 50 Phone: (03) 9203 9700 Fax: (03) 9686 2197 Email: [email protected] Web: http://www.esv.vic.gov.au/

WorkSafe

WorkSafe needs to provide WorkSafe written verification before High www.worksafe.vic.gov.au Victoria Risk Work Units can be added to an RTO’s scope of Info line: 1800 136 089 registration.

of 50 GLOSSARY

Code Nationally endorsed Training Package qualification code.

Title Nationally endorsed Training Package qualification title.

Unit Code Nationally endorsed Training Package unit code.

Unit Title Nationally endorsed Training Package unit title.

Nominal Hours The anticipated hours of supervised learning or training deemed necessary to conduct training and assessment activities associated with the program of study. These hours are determined by the Victorian State Training Authority. Nominal hours may vary for a qualification depending on the units of competency selected.

Scope of Registration Scope of registration specifies the AQF qualifications and/or units of competency the training organisation is registered to issue and the industry training and/or assessment services it is registered to provide.