DOCSLIB.ORG

Terahertz Four-Wave Mixing Spectroscopy for Study of Ultrafast Dynamics in a Semiconductor Optical Amplifier Jianhui Zhou, Namkyoo Park, Jay W

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Terahertz Four-Wave Mixing Spectroscopy for Study of Ultrafast Dynamics in a Semiconductor Optical Amplifier Jianhui Zhou, Namkyoo Park, Jay W Terahertz four-wave mixing spectroscopy for study of ultrafast dynamics in a semiconductor optical amplifier Jianhui Zhou, Namkyoo Park, Jay W. Dawson, and Kerry J. Vahala Department of&lied Physics, Mail Stop 128-95, California Institute of Technology, Pasadena, Calijornia YI ID Michael A. Newkirk and Barry 1. Miller A Tk T Bell Laboratories, Holmdel, New Jersey 07733 (Received 2 April 1993; accepted for publication 18 June 1993) Ultrafast dynamics in a 1Spm tensile-strained quantum-well optical amplifier has been studied by highly nondegenerate four-wave mixing at detuning frequencies up to 1.7 THz. Frequency response data indicate the presence of two ultrafast physical processes with characteristic relaxation lifetimes of 650 fs and < 100 fs. The longer time constant is believed to be associated with the dynamic carrier heating effect. This is in agreement with previous time-domain pump-probe measurements using ultrashort optical pulses. Understanding the ultrafast intraband dynamics of the range of several hundred microwatts. This is in con- semiconductor active layers is of considerable importance trast to time-domain pump-probe measurements, where since, in addition to purely fundamental considerations, short pulse peak power is usually in the range of several the physical processes involved influence the modulation hundred milliwatts or higher.“S5 The information revealed response and spectral properties of semiconductor lasers in TFWM measurements is therefore readily applicable to and can induce crosstalk between multiplexed signals in analysis of modulation and spectral properties of semicon- semiconductor optical amplifiers. ductor lasers, where small-signal data are often needed. Ilnt.il recently, time-domain pump-probe measurement Among other advantages of TFWM are the simplicity of using ultrashort optical pulse~,‘-~ pioneered by Ippen and the experimental setup and better accuracy in measure- co-workers,1’.-3 has been the only direct technique for study ment of lifetime data since short lifetimes are mapped to a of ultrafdst intraband dynamics. These measurements have wide frequency span. In addition to providing a frequency- revealed characteristic time constants of 550 and 200 fs in domain tool for investigation of intraband dynamics, 1.5 ~i-rmInGaAsP bulk optical amplifiers’ and 700 and 250 TFWM measurements provide signal spectra that give am- fs in 1.5 /ltm multiple quantum-well optical amplifiers.” The plifier crosstalk strength for widely separated optical chan- longer time constants were attributed to a heated carrier nels as well as efficiency for possible use of TWAs as para- distribution cooling back to an equilibrium temperature metric channel converters. and is referred to as dynamic carrier heating. The shorter The TWA used in this study was a tensile-strained time constants were recently found to be caused by a com- InGaAs/InGaAsP multiple quantum-well TW.A operating bination of effects, including delay in the carrier heating, at 1.5 pm. Details on the structure appear in Refs. 10 and and spectral hole burning.” In addition, measurements on 11. The specific device was operated at a 100 mA bias multiple quantum-well optical amplifiers by Weiss et aZ.” current where the TM mode small-signal gain was mea- have resolved time constants of 2-7 ps, which were attrib- sured to be 20 dB for the wavelengths investigated, and the uted to carrier diffusion in the barrier layer and identified gain ripple less than 0.1 dB. The pump, probe, and local as the carrier capture time. oscillators used in the measurements are three single- Highly nondegenerate four-wave mixing due to ultra- frequency, tunable, Er-doped fiber ring lasers.” These la- fast intraband dynamics in semiconductor gain media was sers, having output powers of about 1 mW, linewidths less first proposed by Agrawal.’ Recently, highly nondegener- than 4 kHz, *’ and low intensity noise levels, I-( provide ideal ate four-wave mixing measurements in semiconductor sources for the TFWM experiment. traveling-wave optical amplifiers (TWAs) have been used As shown in Fig. 1, the optical outputs from the pump as a frequency-domain technique for studies of ultrafast and probe lasers, having optical frequencies fp and fq, dynamics in semiconductors. To date, however, all the were combined using a 3 dB fiber coupler2 and then colli- measurements have been limited to a detuning range of mated and coupled into the TWA using microscope objec- approximately 500 GHz.~-~ Here, we report measurements tives. The optical power coupled into the TWA was about of four-wave mixing in a tensile-strained multiple 250 pc1-w.Two fiber polarization controllers were employed quantum-well TWA at detuning frequencies up to 1.7 to match the polarization state of input pump and probe to THz, which corresponds to an equivalent temporal resolu- the TWA TM mode. Two optical isolators providing 60 dB tion of 94 fs (r= 1/2?rf). To our knowledge, this repre- isolation were placed before and after the TWA to elimi- sents the first report of terahertz four-wave mixing nate feedback caused by the facets of the input and output (TFWM) spectroscopy in semiconductor gain media. fibers, and to also serve as polarization selectors. TFWM is a small-signal technique since semiconduc- During the measurements, the pump laser (f’) was tor dynamics is probed using optical powers typically in ftxed at 1534 nm, while the probe ( fq) was tuned to vary 1179 Appl. Phys. Lett. 63 (9), 30 August 1993 0003-6951/93/63(9)/1179/3/$6.00 @ 1993 American Institute of Physics 1179 Downloaded 20 Dec 2005 to 131.215.225.171. Redistribution subject to AIP license or copyright, see http://apl.aip.org/apl/copyright.jsp FIG. 1. Experimental setup for the TFWM measurement. Detuning Frequency (-GHz) the detuning frequency fP- fq. The four-wave mixing sig- nal at 2fp- fq was heterodyne detected by mixing the sig- FIG. 3. Normalized four-wave mixing signal power vs negative dctuning nal with the fiber-laser local oscillator and tuning the local frequency showing theoretical fits. oscillator near the signal frequency. The mixing frequency was maintained at 4.00 GHz throughout the measurements have extended the simplified formula to include the possi- to eliminate the frequency dependence of detection elec- bility of several physical processes, tronics. The detected photocurrent was amplified by a mi- crowave amplifier with 40 dB gain and then measured us- ing a spectrum analyzer. The detuning frequencies were determined using an opt.ical spectrum analyzer. The optical powers of pump, probe, and local oscillator were As.0 mea- where l&vM, EP, and I$ are amplitudes of the signal, sured, so that the measured four-wave mixing signal could pump, and probe fields, f IS the detuning frequency, and Tj be normalized. and cj are the lifetimes and the complex coupling coeffi- The four-wave mixing signal was measured for detun- cients of the various relaxation processes. Physically, the ing frequencies from - 1.7 to 1.5 THz, limited only by the real and imaginary parts of the coupling coefficient repre- tunability of the fiber lasers used in the experiment. The sent the strengths of the dynamic gain and index gratings signal level at the maximum detuning frequency was still created by the specific relaxation process. Therefore, the about 20 dB above the noise floor, owing to the narrow coupling coefficients can serve, in some cases, as a criterion linewidth and low intensity noise of the fiber lasers. The for identifying the responsible physical mechanisms. normalized signal power as a function of detuning fre- The dashed line in Figs. 2 and 3 represents the re- quency is illustrated in Figs. 2 and 3. sponse accounting for carrier density modulation (inter- In prior work at lower frequencies, we have been able band recombination) only. The deviation of the measured to model these effects using uncoupled rate equations char- signal data from this one time constant fit indicates the acterized by a lifetime and a complex coupling coefi- presence of the ultrafast relaxation mechanisms. In addi- cient.“‘” To study the new ultrahigh-frequency data we tion, the asymmetric nature of the signal spectrum is be- lieved to be caused by phase interferences which occur between various mechanisms present. Since the positive detuning data show constructive interferences, we esti- mated a second time constant (i.e., in addition to the in- -10 0 Bpsnmmtal oat.4 ci- - - , Trw ConrtanlF,l E - * mr comtant Fit terband recombination time constant) using the positive $ - 2 me Constant6, signal spectrum. However, a two time constant response is i: -20 a still insufficient to provide a good fit for the whole signal P spectrum as shown in the figures. This indicates the exist- .o -30 m ence of an even faster process. A third term having a life- P ,N time of < 100 fs was required to obtain a good fit. -40 : Using the three-term formula, excellent fits were ob- 2 tained for both positive and negative detuning data with -50 '. ‘\ the same parameter set (see Figs. 2 and 3:-3 time con- ‘l . -50:o , . a&- . ..( . ,A stant fit.). The fitting paramet.ers are as follows: cl 100 1000 10000 = 5.6%“.““, ~,=0,0642r”.~~, ~;=O.O113e”~~“, .rl =200 ps, Detuning Frequency (GHz) r,= 650 fs, and ~~= 50 fs. Here we have used a value of 3.6 for the linewidth enhancement factor. It is important to FIG. 2. Normalized four-wave mixing signal power vs positive detuning note that the fits are quite sensitive to the longer intraband frrquency showing theoretical fits. relaxation time constant 650 fs, but are relatively insensi- 1180 Appl. Phys. Lett., Vol. 63, No. 9, 30 August 1993 Zhou et a/. 1180 Downloaded 20 Dec 2005 to 131.215.225.171. Redistribution subject to AIP license or copyright, see http://apl.aip.org/apl/copyright.jsp tive to the shorter time constant, because the equivalent With improvements to the fiber lasers, the detuning fre- temporal resolution of this measurement system is still lim- quency could be further extended to provide even better ited.
Load more

Recommended publications
  • Semiconductor Light Sources
    Laser Systems and Applications Couse 2020-2021 Semiconductor light sources Prof. Cristina Masoller Universitat Politècnica de Catalunya [email protected] www.fisica.edu.uy/~cris SCHEDULE OF THE COURSE Small lasers, biomedical Semiconductor light sources lasers and applications . 1 (11/12/2020) Introduction. 7 (19/1/2021) Small lasers. Light-matter interactions. 8 (22/1/2021) Biomedical lasers. 2 (15/12/2020) LEDs and semiconductor optical amplifiers. Laser models . 3 (18/12/2020) Diode lasers. 9 (26/1/2021) Laser turn-on and modulation response. Laser Material Processing . 10 (29/1/2021) Optical injection, . 4 (22/12/2020) High power laser optical feedback, polarization. sources and performance improving novel trends . 11 (2/2/2021) Students’ . 5 (12/1/2021) Laser-based presentations. material macro processing. 12 (5/2/2021) Students’ . 6 (15/1/2020) Laser-based presentations. material micro processing. 9/2/2021: Exam Lecturers: C. Masoller, M. Botey 2 Learning objectives . Understand the physics of semiconductor materials and the electron-hole recombination mechanisms that lead to the emission of light. Learn about the operation principles of light emitting diodes (LEDs) and semiconductor optical amplifiers (SOAs). Become familiar with the operation principles and characteristics of laser diodes (LDs). 3 Outline: Semiconductor light sources . Introduction . Light-matter interactions in semiconductor materials . Light Emitting Diodes (LEDs) . Semiconductor optical amplifiers (SOAs) . Laser diodes (LDs) The start of the laser diode story: the invention of the transistor Nobel Prize in Physics 1956 “For their research on semiconductors and their discovery of the transistor effect”. The invention of the transistor in 1947 lead to the development of the semiconductor industry (microchips, computers and LEDs –initially only green, yellow and red).
    [Show full text]
  • White Paper Introduction to Optical Amplifiers
    White Paper Introduction to Optical Amplifiers June 2010 1 Introduction Optical amplifiers are a key enabling technology for optical communication networks. Together with wavelength-division multiplexing (WDM) technology, which allows the transmission of multiple channels over the same fiber, optical amplifiers have made it possible to transmit many terabits of data over distances from a few hundred kilometers and up to transoceanic distances, providing the data capacity required for current and future communication networks. The purpose of this paper is to provide an overview of optical amplifiers. For a more detailed discussion on the implementation of optical amplifiers using Erbium doped fiber amplifier (EDFA) technology see Finisar’s white paper “Introduction to EDFA technology”. 2 What Are Optical Amplifiers? A basic optical communication link comprises a transmitter and receiver, with an optical fiber cable connecting them. Although signals propagating in optical fiber suffer far less attenuation than in other mediums, such as copper, there is still a limit of about 100 km on the distance the signals can travel before becoming too noisy to be detected. Before the commercialization of optical amplifiers, it was necessary to electronically regenerate the optical signals every 80-100 km in order to achieve transmission over long distances. This meant receiving the optical signal, cleaning and amplifying it electronically, and then retransmitting it over the next segment of the communication link. While this can be feasible when transmitting a single low capacity optical channel, it quickly becomes unfeasible when transmitting tens of high capacity WDM channels, resulting in a highly expensive, power- hungry and bulky regenerator station, as shown in Figure 1a.
    [Show full text]
  • Optical Amplifiers.Pdf
    ECE 6323 . Introduction . Fundamental of optical amplifiers . Types of optical amplifiers Erbium-doped fiber amplifiers Semiconductor optical amplifier Others: stimulated Raman, optical parametric . Advanced application: wavelength conversion . Advanced application: optical regeneration . What is optical amplification? . What use is optical amplification? Review: stimulated emission • Through a population, net gain occurs when there are more stimulated photons than photons absorbed • Require population inversion from input pump • Amplified output light is coherent with input light Optical amplification Energy pump Pin Pout Pin P Coherent z P Pin (N2 N1) z dP gP dz Optically amplified signal: coherent with input: temporally, If g>0: Optical gain spatially, and with polarization (else, loss) . What is optical amplification? . What use is optical amplification? • The most obvious: to strengthen a weakened signal (compensate for loss through fibers) • …But why not just detect the signal electronically and regenerate the signal? • System advantage: boosting signals of many wavelengths: key to DWDM technology • System advantage: signal boosting through many stages without the trouble of re-timing the signal • There are intrinsic advantages with OA based on noise considerations • Can even be used for pre-amplification of the signal before detected electronically . Introduction . Fundamental of optical amplifiers . Types of optical amplifiers Erbium-doped fiber amplifiers Semiconductor optical amplifier Others: stimulated Raman, optical
    [Show full text]
  • Section 5: Optical Amplifiers
    SECTION 5: OPTICAL AMPLIFIERS 1 OPTICAL AMPLIFIERS S In order to transmit signals over long distances (>100 km) it is necessary to compensate for attenuation losses within the fiber. S Initially this was accomplished with an optoelectronic module consisting of an optical receiver, a regeneration and equalization system, and an optical transmitter to send the data. S Although functional this arrangement is limited by the optical to electrical and electrical to optical conversions. Fiber Fiber OE OE Rx Tx Electronic Amp Optical Equalization Signal Optical Regeneration Out Signal In S Several types of optical amplifiers have since been demonstrated to replace the OE – electronic regeneration systems. S These systems eliminate the need for E-O and O-E conversions. S This is one of the main reasons for the success of today’s optical communications systems. 2 OPTICAL AMPLIFIERS The general form of an optical amplifier: PUMP Power Amplified Weak Fiber Signal Signal Fiber Optical AMP Medium Optical Signal Optical Out Signal In Some types of OAs that have been demonstrated include: S Semiconductor optical amplifiers (SOAs) S Fiber Raman and Brillouin amplifiers S Rare earth doped fiber amplifiers (erbium – EDFA 1500 nm, praseodymium – PDFA 1300 nm) The most practical optical amplifiers to date include the SOA and EDFA types. New pumping methods and materials are also improving the performance of Raman amplifiers. 3 Characteristics of SOA types: S Polarization dependent – require polarization maintaining fiber S Relatively high gain ~20 dB S Output saturation power 5-10 dBm S Large BW S Can operate at 800, 1300, and 1500 nm wavelength regions.
    [Show full text]
  • Optical Amplifier for Space Applications
    Optical Amplifier for Space Applications Richard L. Fork, Spencer T. Cole, Lisa J. Gamble, William M. Diffey, Department of Electrical and Computer Engineering Univers#y of Alabama in Huntsville, Huntsville, Alabama 35899 fork_@,ece.uah.¢du, Andrew S. Keys NASA-Marshall Space Flight Center, Huntsville, Alabama 35812 Abstract: We describe an optical amplifier designed to amplify a spatially sampled component of an optical wavefront to kilowatt average power. The goal is means for implementing a strategy of spatially segmenting a large aperture wavefront, amplifying the individual segments, maintaining the phase coherence of the segments by active means, and imaging the resultant amplified coherent field. Applications of interest are the transmission of space solar power over multi-megameter distances, as to distant spacecraft, or to remote sites with no preexisting power grid. ©!999 Optical Society of America OCIS codes: (140.3280) Laser amplifiers; (140.3290) Laser arrays References and Links I. J. Mankins, "A Fresh Look at Space Solar Power: New Architectures, Concepts and Technologies", h.ttp:/twww.tler.neqsunsat/freshlook2.htm, October 6 (1997). 2. J. Mankins and J. Howell, "An Executive Summary of Recent Space Solar Power Studies and Findings", NASA Space Solar Power Exploratory Research & Technology (SERT), April 23 (! 999). 3. R.L, Fork, C.V. Shank, and R.T. Yen, "Amplification of 70-fs optical pulses to gigawatt powers," Appl. Phys. Lett. 41,223-225, (1982). 4. A. Giesen, H. Hi, gel, A. Voss, K. Wittig, U. Brauch, H. Opower, "Scalable Concept for Diode-Pumped High- Power Solid-State Lasers", Applied Physics B58, 365-72 (1994). 5.
    [Show full text]
  • Properties of Mode-Locked Optical Pulses in a Dispersion-Managed Fiber-Ring Laser Using Semiconductor Optical Amplifier As Active Device Jacques W
    Properties of Mode-Locked Optical Pulses in a Dispersion-Managed Fiber-Ring Laser Using Semiconductor Optical Amplifier as Active Device Jacques W. D. Chi, Arnaud Fernandez, Chao Lu To cite this version: Jacques W. D. Chi, Arnaud Fernandez, Chao Lu. Properties of Mode-Locked Optical Pulses in a Dispersion-Managed Fiber-Ring Laser Using Semiconductor Optical Amplifier as Active Device. IEEE Journal of Quantum Electronics, Institute of Electrical and Electronics Engineers, 2013, 49 (1), pp.80-88. 10.1109/JQE.2012.2230317. hal-00849989 HAL Id: hal-00849989 https://hal.archives-ouvertes.fr/hal-00849989 Submitted on 2 Aug 2013 HAL is a multi-disciplinary open access L’archive ouverte pluridisciplinaire HAL, est archive for the deposit and dissemination of sci- destinée au dépôt et à la diffusion de documents entific research documents, whether they are pub- scientifiques de niveau recherche, publiés ou non, lished or not. The documents may come from émanant des établissements d’enseignement et de teaching and research institutions in France or recherche français ou étrangers, des laboratoires abroad, or from public or private research centers. publics ou privés. 80 IEEE JOURNAL OF QUANTUM ELECTRONICS, VOL. 49, NO. 1, JANUARY 2013 Properties of Mode-Locked Optical Pulses in a Dispersion-Managed Fiber-Ring Laser Using Semiconductor Optical Amplifier as Active Device Jacques W. D. Chi, Arnaud Fernandez, and Chao Lu, Member, IEEE Abstract— A hybrid model is proposed in order to exploit the (TB) using root-mean-square (RMS) definition, i.e.,thestan- idea of compensating semiconductor optical amplifiers (SOAs) dard deviation of energy densities of a signal in the time- nonlinearity by adjusting cavity dispersion in a SOA-fiber ring and frequency domain.
    [Show full text]
  • Semiconductor Optical Amplifiers in Optical Communication System-Review
    International Journal of Engineering Research & Technology (IJERT) ISSN: 2278-0181 Vol. 2 Issue 10, October - 2013 Semiconductor optical amplifiers in optical Communication system-Review Aruna Rani 1, Mr. Sanjeev Dewra 2 1M.tech Scholar, Shaheed Bhagat Singh state technical campus, Ferozepur. 2Assistant professor & Head of ECE Department, Shaheed Bhagat Singh state technical campus, Ferozepur. Abstract In this paper Semiconductor optical amplifier and their applications have been reviewed. SOAs are under rapid development to achieve polarization independent gain, low facet reflectivity, good coupling to optical fibers, and high saturation power. A single optical amplifier can replace all the multiple components required for an electronic regeneration station and eliminate the need for electrical-optical and optical-electrical conversions. SOAs have been employed to overcome distribution losses in the optical communication applications and pursued for metropolitan-area networks as a low-cost alternative to fiber amplifiers. Keywords – Optical communication system, Semiconductor optical amplifier, Wavelength converter, Fabry-Perot Semiconductor Optical Amplifier 1. Introduction As the optical signal travels in a fiber waveguide, it suffers attenuation (loss of power). For very long fiber spans, the optical signal may be so attenuated that it become too weak to excite reliably the (receiving) photo detector, where upon the signal may be detected at an expected low bit error rate (~10-9 to ~10-11)[1].Optical amplifiers are key devices that reconstitute the attenuated optical signal, thus expanding the effective fiber span between the data source and destination. A semiconductor optical amplifier is an optical amplifier based on a semiconductorIJERTIJERT gain medium. It is essentially like a laser diode where the end mirrors have been replaced with anti-reflection coatings.
    [Show full text]
  • An Optical Amplifier Pump Laser Reference Design Based on the AMC7820
    Application Report SBAA072A – May 2002 – Revised March 2005 An Optical Amplifier Pump Laser Reference Design Based on the AMC7820 Rick Downs Data Acquisition Products ABSTRACT The AMC7820 is an integrated circuit designed for analog monitoring and control. Its features are put to use in this reference design for laser and thermoelectric cooler control in EDFA and Raman optical amplifiers. The resulting circuit fits into a credit-card sized space. Contents Introduction .............................................................................................................................................3 Erbium-Doped Fiber Amplifier Basics ..................................................................................................4 Pump Laser Module................................................................................................................................5 Laser Diode ...........................................................................................................................................6 Thermoelectric Cooler (TEC).................................................................................................................6 Thermistor..............................................................................................................................................7 Back Facet Monitor................................................................................................................................8 AMC7820: An Ideal Device for Control Loop Solutions ......................................................................8
    [Show full text]
  • Efficient Raman Amplifiers and Lasers in Optical Fibers and Silicon
    Efficient Raman Amplifiers and Lasers in Optical Fibers and Silicon Waveguides: New Concepts Vom Promotionsausschuss der Technischen Universit¨atHamburg-Harburg zur Erlangung des akademischen Grades Doktor-Ingenieur (Dr.-Ing.) genehmigte Dissertation von Michael Krause aus Hamburg 2007 1. Gutachter: Prof. Dr. Ernst Brinkmeyer, TU Hamburg-Harburg 2. Gutachter: Prof. Dr. Klaus Petermann, TU Berlin 3. Gutachter: Prof. Dr. Klaus Sch¨unemann,TU Hamburg-Harburg Tag der m¨undlichen Pr¨ufung:6. Februar 2007 Uniform Resource Name (URN): urn:nbn:de:gbv:830-tubdok-5769 Danksagung Diese Arbeit ist an der Technischen Universit¨at Hamburg-Harburg w¨ahrend meiner T¨atigkeit als wissenschaftlicher Mitarbeiter in der Arbeitsgruppe Optische Kommu- " nikationstechnik\ entstanden. Ganz herzlich danken m¨ochte ich zun¨achst dem Leiter dieser Arbeitsgruppe, Herrn Prof. Dr. Ernst Brinkmeyer, fur¨ die M¨oglichkeit zur Mitar- beit und Promotion, die umfassende Betreuung und die Unterstutzung¨ s¨amtlicher meiner Vorhaben. Zu gr¨oßtem Dank verpflichtet bin ich weiterhin Hagen Renner fur¨ die unz¨ahligen Gelegenheiten zum ¨außerst ergiebigen fachlichen und nicht-fachlichen Diskutieren und Ideenfinden sowie schließlich fur¨ das Korrekturlesen dieser Arbeit. Bei Sven Cierullies m¨ochte ich mich fur¨ die ergebnisreiche Zusammenarbeit auf dem Gebiet der Raman-Faserlaser und die immer angenehme Stimmung im gemeinsamen Buro¨ bedanken. Weiterhin danke ich Raimonda Stanslovaityte, Robert Draheim, Yi Han und Heiko Fimpel, die im Rahmen ihrer Studien- und Diplomarbeiten hilfreiche Beitr¨age zu meiner Arbeit geliefert haben. Auch allen ubrigen¨ Mitarbeitern und Studenten der Arbeitsgruppe sei gedankt fur¨ ihren Beitrag zu einer gelungenen Arbeitsumgebung; J¨org Voigt danke ich fur¨ die Bera- tung bei praktisch-experimentellen Fragen und Frank Knappe fur¨ vielerlei Hilfestellun- gen.
    [Show full text]
  • Module 21 : Raman Amplifier
    Module 21 : Raman Amplifier Lecture : Raman Amplifier Objectives In this lecture you will learn the following Introduction Origin of Raman Scattering Raman Scattering in Optical Fibers Fiber Raman Amplifier Pumping Schemes for Raman Amplifier Impact of Raman Scattering on WDM system Introduction Raman scattering, especially if it is stimulated, is a very important non-linear effect because it affects the SNR in a WDM system. It can also be used for amplification of the optical signals in a long haul optical communication link. The spontaneous Raman scattering was discovered by Sir C. V. Raman. Incase of spontaneous Raman scattering, a small portion of the incident light is transformed into a new wave with lower or higher frequency. This transformation is because of the interaction of the photon with the vibrational modes of the material. The transformation efficiency of spontaneous Raman scattering is very low. Typically photons 1 part per million are transformed to the new wavelength per cm length of the medium. Contrary to spontaneous Raman scattering, stimulated Raman scattering can transform a large fraction of the incident light in the new frequency-shifted wave. Origin of Raman Scattering In principle, spontaneous Raman scattering can be observed in any material. If a medium is irradiated by an intense monochromatic light and if the scattered light is studied with a spectrometer, the scattered light shows new wavelengths in addition to the original wavelength. The wave which irradiates the material is called the Pump wave, the waves with lower frequencies are called the Stokes waves, and the waves with higher frequency are called the Anti-Stokes waves.
    [Show full text]
  • A Tunable Multiwavelength Laser Employing a Semiconductor Optical Amplifier and an Opto-VLSI Processor
    View metadata, citation and similar papers at core.ac.uk brought to you by CORE provided by Research Online @ ECU Edith Cowan University Research Online ECU Publications Pre. 2011 2008 A Tunable Multiwavelength Laser Employing a Semiconductor Optical Amplifier and an Opto-VLSI Processor Muhsen Aljada Edith Cowan University Kamal Alameh Edith Cowan University Yong T. Lee Gwangju Institute of Science and Technology, Gwangju, South Korea Follow this and additional works at: https://ro.ecu.edu.au/ecuworks Part of the Computer Sciences Commons 10.1109/LPT.2008.921823 This is an Author's Accepted Manuscript of: Aljada, M. , Alameh, K. , & Lee, Y. T. (2008). A Tunable Multiwavelength Laser Employing a Semiconductor Optical Amplifier and an Opto-VLSI Processor. IEEE Photonics Technology Letters, 20(10), 815-817. Available here © 2008 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes, creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works. This Journal Article is posted at Research Online. https://ro.ecu.edu.au/ecuworks/1092 IEEE PHOTONICS TECHNOLOGY LETTERS, VOL. 20, NO. 10, MAY 15, 2008 815 A Tunable Multiwavelength Laser Employing a Semiconductor Optical Amplifier and an Opto-VLSI Processor Muhsen Aljada, Member, IEEE, Kamal Alameh, Senior Member, IEEE, and Yong Tak Lee Abstract—We propose and experimentally demonstrate a stable tunable multiwavelength laser employing a semi- conductor optical amplifier (SOA) in conjunction with an opto-very-large-scale-integration (VLSI) processor.
    [Show full text]
  • Signal Regeneration - Optical Amplifiers
    Signal regeneration - optical amplifiers In any atom or solid, the state of the electrons can change by: 1) Stimulated absorption - in the presence of a light wave, a photon is absorbed, the electron is excited to a higher energy level. E2 Light E1 2) Stimulated emission - in the presence of a light wave, a photon is emitted, the electron drops too a lower energy level. E2 Light Light E1 3) Spontaneous emission - in the absence of light, a photon is emitted and the electron drops to a lower energy level. E2 Light E1 NOTE: For stimulated processes , the absorbed or emitted photon has exactly the same phase φ and frequency ω (or wavelength λ ) as the stimulating light (coherence). Lecture 22: Optical Amplifiers Optical amplifiers... continued Stimulated processes (emission and absorption) are proportional to the light intensity at the appropriate frequency. Stimulated emission rate: ω r21(stim) = B·I( ) Stimulated absorption rate: E E2 ω 2 r12(stim) = B·I( ) !ω Spontaneous emission rate: !ω Energy r21(spon) = A E E1 1 A and B are the Einstein coefficients These rates determine the probability that a particular electron will undergo stimulated (or spontaneous) emission within a given time interval. Under normal circumstances we do not observe the stimulated process because the probability of the spontaneous process occurring is much higher. Lecture 22: Optical Amplifiers Optical amplifiers... continued How does the intensity I(ω ) of a light wave change when passing through a medium with n1 atoms in the ground state and n2 atoms in the excited state? ∂ωI() ~(!!ωωωnr−= nr ) ( n −⋅⋅ n ) B I () ∂x221 112 2 1 ∂ωI() =−αωI() ∂x Integration of this equation gives: = −α x I Ioe The absorption/gain coefficient α depends on the number of atoms in the excited ( n2 ) and ground states (n1) αω! −⋅ ~(nnB12 ) α Equilibrium (n1>n2 ( positive)) Absorption α Population Inversion (n2>n1) ( negative) Gain Need to “pump” electrons to N2 from N1.
    [Show full text]